|
| 1 | Excavation in hilly area in all heights and depths and in all kind of soil by manual/mechanical means including saturated soil comprising of ordinary soil, soft rocks, hard rocks, chieselling/wedging out rock (where blasting is prohibited) and their intermediate classification of soil, setting out true to the required lines, grades, width cutting and trimming of side slopes to level as shown in the drawing and as directed by engineer-in-charge at site according to the MORD technical specification section 300 and 1600 and sorting out useful materials and stacking the same in all leads, lifts in acquired width of road and transportation of un-useful material for filling in road ways, camber, embankments for grade improvements and disposal of all surplus material tothe approved dumping sites through all modes of transportation upto 2 kmincluding head load or animal transport or mechanical means along with its leveling, fine dressing and carriage of machineries, materials, tools, equipments and safety measures and other incidentals necessary to complete the work by mechanical means and labour if required. Recovery of stones to the tune of 4202.94 cubic metre quantity ( four thousand two hundred two point ninty four ) cubic metres at the rate of 300/- (Rupees Three hundred) per cubic metre shall be effected from the contractor\"s running bills on pro-rata basis as per actual quantity executed. Any loss to the public, private property during the course of execution shall be the absolute responsibility of the contractor, which shall have to be duly compensated by him in all cases. The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST. |
| 2 | Construction of embankment with approved materials deposited at site from roadway cutting and excavation from drain and foundation of other structures graded and compacted to meet requirement including setting out, true to the lines, grades, width and side slopes in accordance with drawing including spreading the embankment material with motor grader in successive layer ofin layer 200mm (two hundred millimetre) uniforms thickness and compacting with vibratory roller 8-10 ( eight to ten) tonne static weight to meet requirement of Tables 300.1 and 300.2 as per MORD Technical Specification section 300 & 1600 and as per direction of Engineer-in-charge including carriage of materials within all leads, lifts and other incidentals. The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST. |
| 3 | Construction of subgrade and earthen shoulders with approved material obtained from borrow pits with in all lifts and leads, transporting to site, spreading, grading by mechanical means to required slope and compacted with three wheel 80-100 (eighty - hundred) kN static roller to meet requirement of Table 300.2 complete as per MORD technical Specification section 400 and as per direction of Engineer-in-charge including carriage of materials within all leads, lifts and other incidentals. The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST. |
| 4 | Earth work in excavation for all type of road structure such as retaining walls, breast walls, culverts, drain and Parapets etcetra in all type of classification of soil comprising of ordinary soil, ordinary rock, hard rock chiseling /wedging out rocks (Where blasting is prohibited) as per drawings and M.O.R.D. technical specification section 300 and 1600 and as per direction of the Engineer- In – Charge including setting out, construction of shoring and bracing, removal of stumps and other deleterious materials and disposal of materials upto any lead and lift including dressing of sides, bottom and back filling in trenches with excavatedsuitable approved material to the original surface in layer not executing 150 mm (one hundred fifty millimetre) compacted thicknessincluding shoring and strutting and pumping and bailingout water (surface and sub soil water ) upto any depth any quantam of water including cleaning of slush which may arise out during dewatering complete as per direction of Engineer-in-Charge. Including carriage of materials within all leads, lifts and other incidentals. The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST. |
| 5 | Back filling with granular material behind abutments, wing walls, return walls and retaining walls complete as per drawingandM.O.R.D. technical specifications section 1200 and 1600 and as per direction of Engineer – in- Charge including carriage of materials within all leads, liftsand other incidental . The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST. |
| 6 | Loosening of the ground upto a level of 300 mm (Three hundred milimeter) below the subgrade level, watered, graded and compacted in layers to meet requirement of Tables 300.1 and 300.2 for subgrade construction as per Technical Specification Clause 303.5.2. |
| 7 | Construction of granular sub-base by providing well graded material, spreading in uniform layers with motor grader / Tractor mount grader on prepared surface, mixing by mix in place method with rotavatorat OMC, and compacting with smoothwheelroller to achieve thedesired density, complete as per Technical Specification Clause 401. |
| 8 | Providing, laying and spreading Material on a prepared sub grade, adding the designed quantity of cement to the spread Material, mixing in place with rotavator, grading with the motor grader and compacting with the road roller at OMC to achieve the desired unconfined compressive strength and to form a layer of base. as per the entire satisfaction and directions of Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST. |
| 9 | Providing and applying primer coat with Bitumen emulsion (SS-1)on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.90- 1.2 kg/sqm using mechanical means as per Technical Specification Clause 502. as per the entire satisfaction and directions of Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST. |
| 10 | Providing and applying tack coat on the prepared granular surface treated with primer and cleaned with hydraulic broom and spraying tack coat @0.20 to 0.25 kg (Zero point two zero to zero point two five) per Square metre as per MORD technical specification section 500, and as perdirection of Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidentals. The rate is including octroi, royality, malkana toll tax and other taxes imposed by the Government but excluding GST. |
| 11 | Providing, laying and rolling of close-graded premix surfacing material of 20 mm thickness composed of 11.2 mm to 0.9 mm (Eleven point two milimeter to zero point nine milimeter)(Type-A) aggregates using penetration grade bitumen to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 8-10 kN static roller and finishing to required level and grades as per Technical Specification Clause 509 |
| 12 | Construction of Panel concrete, plain cement concrete pavement, thickness as per design, over a prepared sub base,as per Clause 1501.2.2 design mixM30coarse and fine aggregates conforming to IS:383, maximum size of coarse aggregate not exceeding 25 mm (Twenty five milimeter), mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel, laying and fixing of 125 (One hundred twenty five) micron thick polythene film, wedges, steel plates including levelling the formwork as per drawing), spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including provision of contraction and expansion, construction joints, applying debonding strips, primer, sealant, dowel bars, near approaches to bridge/culvert and construction joints, admixture as approved, curing of concrete slabs for 14 days. Curing compound (where specified) and water finishing to lines and grade as per drawing and technical specification Clause 1501. PCC Grade M-30 Each Panel (0.50 x 0.50) thickness 150 mm. The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST. |
| 13 | Providing and errecting \" W\" metal beam crash barrier composing of 3 mm (three millimetre)thick corrugated sheet metal beam rail, 70 cm (seventy centimetre) above road/ Ground level fixed on I.S.M.C. series channel vertical post 150 x 75 x 5 mm (one hundred fifty into seventy five into five millimetre) spacerd 2 m (two metre) centre to centre 1.8 m (one point eight metre) high, 1.1 m (one point one metre) below ground/ road level, all steel part and fitments to be galvanised by hot dip process. All fitting to conforms to I.S 1367 and I.S. 1364 metal beam rail to be fixed on the vertical post with spacer of channel section 150x75x5mm (one hundred fifty into seventy five into five millimetre)and 330 mm (three hundred thirty millimetre) long complete as per MORTH technical specification section 800 as per the direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidental. The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST. |
| 14 | Providing and laying mechanically mixed and vibrated concrete for plain cement concrete inopen foundation for all type of structurecomplete using plain cement concrete nominal mix 1: 4: 8 ( One cement into four sand into eight graded crushed/broken stone aggregate 40mm(fourty millimetre) nominal size on ground or under waterandcuring complete including pumpingor bailing out water, dewateringremoval of slush as required at site which may arrise at the time oflaying concrete completefor all heights/ depths includingthe cost of form workas per drawings and M.O.R.D. technical specification section 800, 900 and 1200 as per the direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidental. The rate is including octroi,royality, Malkana, toll tax, or other taxes imposed by the Government but excluding GST. |
| 15 | Providing and laying100mm (one Hundred millimetre) dia PVC pipe made of Finolex weep holes in brick masonry/stone masonry, plain reinforced concrete, Abutments, Wing walls, Return walls and retaining/breast walls extended through the full width of the structure with slope I(V):20(H)(One vertical : Twenty Horizontal) towards draining face complete as per drawing and MORD technical specification section 700 and 1200 and as per direction of Engineer-in-charge including carriage of materials within all leads, lifts and other incidentals. The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST. |
| 16 | Drainage Spouts complete as per drawing and Technical specificationincluding carriage of material within all leads, lifts and other incidental. The rate is including octroi,royality, Malkana, toll tax, or other taxes imposed by the Government but excluding GST. |
| 17 | Providing and laying of boulder apron laid in wire crates with 4 mm (four millimetre) dia GI wire conforming to IS:280 and IS:4826 in 100 mm x 100 mm (one hundred millimetre into one hundred millimetre) mesh (woven diagonally) including 10 % (ten percent) extra for laps and joints laid with stone boulders weighing not less than 25 kg (tewnty five kilogram) each as per drawing and MORD technical specifications section 1301 including carriage of materials within all leads, liftsand other incidental . The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST. |
| 18 | Providing and laying mechanically mixed and vibrated concrete for plain cement concreteinopen foundation for all type of structurecomplete using plain cement concreteGrade M-10 (M-Ten) on ground or under waterandcuring complete including pumpingor bailing out water, dewateringremoval of slush as required at site which may arrise at the time oflaying concrete completefor all heights/ depths includingthe cost of form workas per drawings and M.O.R.D. technical specification section 800, 900 and 1200 as per the direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidental. The rate is including octroi,royality, Malkana, toll tax, or other taxes imposed by the Government but excluding GST. |
| 19 | Providing and laying mechanically mixed and vibrated plain cement concretein road structure using plain cement concrete grade M-15 (M-Fifteen) on ground or under water in substructure and curing complete including pumping or bailing out water completefor all heights/depths including cost of form work in craddle bedding culvert as per drawing and MORD technical specification section 800, 900 and 1100 including carriageof materials with in all leads, lifts and otherincidental,as per the entire satisfaction and directions of Engineer-in-Charge . The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST. |
| 20 | Providing and laying mechanically mixed and vibrated plain cement concretein road structure using plain cement concrete design mix M-20 (M-Twenty)on ground or under water and curing complete including pumping or bailing out water completefor all heights/depths including cost of form work in craddle bedding culvert as per drawing and MORD technical specification section 800, 900 and 1100 including carriageof materials with in all leads, lifts and otherincidental,as per the entire satisfaction and directions of Engineer-in-Charge . The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST. |
| 21 | Providing and laying mechanically mixed and vibrated reinforced cement concretein road structure using reinforced cement concrete design mix M-20 (M-Twenty) on ground or under water and curing complete including pumping or bailing out water completefor all heights/depths including cost of form work in craddle bedding culvert as per drawing and MORD technical specification section 800, 900 and 1100 including carriageof materials with in all leads, lifts and otherincidental,as per the entire satisfaction and directions of Engineer-in-Charge . The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST. |
| 22 | Providing and laying mechanically mixed and vibrated reinforced cement concretein road structure using reinforced cement concrete design mix M-25 (M-Twenty five)on ground or under water and curing complete including pumping or bailing out water completefor all heights/depths including cost of form work in craddle bedding culvert as per drawing and MORD technical specification section 800, 900 and 1100 including carriageof materials with in all leads, lifts and otherincidental,as per the entire satisfaction and directions of Engineer-in-Charge . The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST. |
| 23 | Providing and laying mechanically mixed and vibrated reinforced cement concrete in road structure using reinforced cement concrete gradeM-30 (M-Thirty)on ground or under wateron superstructure and curing complete including pumping or bailing out water completefor all heights/depths including cost of form work in craddle bedding culvert (for wearing course) onlyas per drawing and MORD technical specification section 800, 900 and 1100 including carriageof materials with in all leads, lifts and otherincidental,as per the entire satisfaction and directions of Engineer-in-Charge . The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST. |
| 24 | Supplying, fitting and placing HYSD reinforcement made of TATA Tiscon / SAILcomplete in sub-structure as per drawing and Technical Specification including carriageof materials with in all leads, lifts and otherincidental,as per the entire satisfaction and directions of Engineer-in-Charge including carriageof materials with in all leads, lifts and otherincidental,as per the entire satisfaction and directions of Engineer-in-Charge . The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST |
| 25 | Providing and laying Rubble stone laid in cement mortar 1:3 (One Cement intothree Sand) laid over cement concrete bedding complete as per drawing and technical specification clause1303 including carriageof materials with in all leads, lifts and otherincidental,as per the entire satisfaction and directions of Engineer-in-Charge . The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST |
| 26 | Construction of RCC railing of M30 Grade in-situ with 20 mm (Twenty milimeter)nominal size aggregate, true to line and grade, tolerance of vertical RCC post not to exceed 1 in 500 (One into five hundred), centre to centre spacing between vertical post not to exceed 2000 mm (Two thousand milimeter), leaving adequate space between vertical post for expansion, complete as per approved drawings and technical specifications.including carriageof materials with in all leads, lifts and otherincidental,as per the entire satisfaction and directions of Engineer-in-Charge . The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST |
| 27 | Providing and laying (to level or slope) 1000mm dia (One thousand millimetres) diameter reinforced cement concrete heavy duty non pressure pipes IS Class NP3 for culverts on first class bedding of granular material in single row including providing and fixing collar with cement mortar 1 : 2 ( One cement : two sand)but excluding the cost of excavation, protection works, back filling, concrete bedding and masonry work in head walls and parapetsas perdrawing andM.O.R.D. technical specifications section 1100 and as per direction of Engineer – in- Charge including carriage of materials within all leads, liftsand other incidental . The rate is includingoctroi,royality, Malkana, toll tax, orother taxes imposed by the Government but excluding GST. |
| 28 | Providing and laying mechanically mixed and vibrated plain cement concretein road structure using plain cement concretegrade M-15 (M-Fifteen) in Parapet and curing complete including pumping or bailing out water completefor all heights/depths including cost of form work in craddle bedding culvert as per drawing and MORD technical specification section 800, 900 and 1100 including carriageof materials with in all leads, lifts and otherincidental,as per the entire satisfaction and directions of Engineer-in-Charge . The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST. |
| 29 | Providing and fixing of typical PMGSY informatory sign board with logo as per M.O.R.D. specification and drawing . Three MS plates of 1.6 mm ( one point six millimetre) thick top and middle plate duly welded with MS flat iron 25mmx5mm ( twenty five millimetres into five millimetres) size on back on edges. The lower plate will be welded with MS angle iron frame of 25mmx25mmx5mm (Twenty five millimetre into twenty five milimetres into five millimetre). The angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to2 Nos. ( Two Nos.) 75mmx75mm (seventy five millimetre into seventy five millimetres) of 12 SWG (twelve standard wire gauge) sheet tubes posts duly embedded in cement concrete M-15 (M fifteen) nominal mix 1:2½ : 5 (One cement: Two and half sand: Five graded or crushed stone aggregate 40mm(Forty milimetres)grade blocks of 450mmx450mmx600mm ( four hundred fifty millimetres into four hundred fifty millimetres into six hundred millimetres), 600mm ( six hundred millimetres) below ground level. The top most diamond plate will be welded to middle plate by 47mmx47mm (Forty seven millimetre into forty seven millimetres) of 12 SWG (Twelve standard wire gauge) steel plate tube. All MS will be stove enamelled on both sides. Lettering and printing arrows, borders etcetera will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections offramed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing andM.O.R.D. technical specifications section 1700 and as per direction of Engineer – in- Charge including carriage of materials within all leads, liftsand other incidental . The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST. |
| 30 | Reinforced cement concrete M-15 (M-fifteen) grade 5th (fifth) Kilometre stone (Precast) of standard design as per IRC :8fixing in position including painting and printing etcetera as per drawing and MORD technical specification section 1700 and as per the directions of the Engineer-in-Charge including carriage of material, within all leads, lifts and other incidentals.The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST. |
| 31 | Reinforced cement concrete M-15 (M-fifteen) grade Ordinary Kilometer Stone (Precast) of standard design as per IRC :8 fixing in position including painting and printing etcetera as per drawing and MORD technical specification section 1700 and as per the directions of the Engineer-in-Charge including carriage of material, within all leads, lifts and other incidentals.The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST. |
| 32 | Reinforced cement concrete M-15 (M-fifteen) grade 200m (two hundred metre) Stone (Precast) of standard design as per IRC :8fixing in position including painting and printing etcetera as per drawing and MORD technical specification section 1700 and as per the directions of the Engineer-in-Charge including carriage of material, within all leads, lifts and other incidentals.The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST. |
| 33 | Reinforced cement concrete M-15 (M-fifteen) grade Boundary Pillars/ Local stone of standard design as per IRC :25fixing in position including finishing and lettering but excluding painting etc extra as per drawing and MORD technical specification section 1700 and as per the directions of the Engineer-in-Charge including carriage of material, within all leads, lifts and other incidentals.The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST. |
| 34 | Providing and erecting direction and place identification retro-reflectorised cautionary, mandatory & informatory sign boards upto 0.90 sqm (zero point nine zero) size board, as per IRC-67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting. 1.5mm (one point five millimetre) thick supported on a mild steel angle iron post 75mm x 75mm x 6mm (seventy five into seventy five into six millimetre ) firmly fixed to the ground by means of properly designed foundation with M-15 grade (M-fifteen grade) cement concrete 450x450x600mm (four hundred fifty into four hundred fifty into six hundred millimetre) , 600mm ( six hundred millimetre) below ground level as per approved drawings and technical specification section 1700, including painting angle iron post with primes and two coats of Epoxy paint as per specification and direction of Engineer-in-Charge includingcarriage of materials within all leads, liftsand other incidental. The rate isincludingoctroi,royality, Malkana, tolltax, or other taxesimposed by the Government but excluding GST. |
| 35 | Providing and erecting direction and place identification retro-reflectorised cautionary, mandatory & informatory sign boards upto 0.60 sqm (zero point six zero) size circular board, as per IRC-67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting. 1.5mm (one point five millimetre) thick supported on a mild steel angle iron post 75mm x 75mm x 6mm (seventy five into seventy five into six millimetre ) firmly fixed to the ground by means of properly designed foundation with M-15 grade (M-fifteen grade) cement concrete 450x450x600mm (four hundred fifty into four hundred fifty into six hundred millimetre) , 600mm ( six hundred millimetre) below ground level as per approved drawings and technical specification section 1700, including painting angle iron post with primes and two coats of Epoxy paint as per specification and direction of Engineer-in-Charge includingcarriage of materials within all leads, liftsand other incidental. The rate isincludingoctroi,royality, Malkana, tolltax, or other taxesimposed by the Government but excluding GST. |
| 36 | Providing and erecting direction and place identification retro-reflectorised cautionary, mandatory & informatory sign boards upto 0.60 x 0.60 sqm (zero point six zero into zero pint six zero) sizerectangular Retro reflective board (Hairpin Bend Curve), as per IRC-67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting. 1.5mm (one point five millimetre) thick supported on a mild steel angle iron post 75mm x 75mm x 6mm (seventy five into seventy five into six millimetre ) firmly fixed to the ground by means of properly designed foundation with M-15 grade (M-fifteen grade) cement concrete 450x450x600mm (four hundred fifty into four hundred fifty into six hundred millimetre) , 600mm ( six hundred millimetre) below ground level as per approved drawings and technical specification section 1700, including painting angle iron post with primes and two coats of Epoxy paint as per specification and direction of Engineer-in-Charge includingcarriage of materials within all leads, liftsand other incidental. The rate isincludingoctroi,royality, Malkana, tolltax, or other taxesimposed by the Government but excluding GST. |
| 37 | Providing and erecting direction and place identification retro-reflectorised cautionary, mandatory & informatory sign boards upto 0.60 x 0.45 sqm (zero point six zero into zero four five) sizerectangular board (Chevron), as per IRC-67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting. 1.5mm (one point five millimetre) thick supported on a mild steel angle iron post 75mm x 75mm x 6mm (seventy five into seventy five into six millimetre ) firmly fixed to the ground by means of properly designed foundation with M-15 grade (M-fifteen grade) cement concrete 450x450x600mm (four hundred fifty into four hundred fifty into six hundred millimetre) , 600mm ( six hundred millimetre) below ground level as per approved drawings and technical specification section 1700, including painting angle iron post with primes and two coats of Epoxy paint as per specification and direction of Engineer-in-Charge includingcarriage of materials within all leads, liftsand other incidental. The rate isincludingoctroi,royality, Malkana, tolltax, or other taxesimposed by the Government but excluding GST. |
| 38 | Providing and erecting direction and place identification retro-reflectorised cautionary, mandatory & informatory sign boards upto 0.90 x 0.30 sqm (zero point nine zero into zero point three zero) sizerectangular board (Hazard Markers), as per IRC-67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting. 1.5mm (one point five millimetre) thick supported on a mild steel angle iron post 75mm x 75mm x 6mm (seventy five into seventy five into six millimetre ) firmly fixed to the ground by means of properly designed foundation with M-15 grade (M-fifteen grade) cement concrete 450x450x600mm (four hundred fifty into four hundred fifty into six hundred millimetre) , 600mm ( six hundred millimetre) below ground level as per approved drawings and technical specification section 1700, including painting angle iron post with primes and two coats of Epoxy paint as per specification and direction of Engineer-in-Charge includingcarriage of materials within all leads, liftsand other incidental. The rate isincludingoctroi,royality, Malkana, tolltax, or other taxesimposed by the Government but excluding GST. |
| 39 | Providing and erecting direction and place identification retro-reflectorised cautionary, mandatory & informatory sign boards upto 0.90 sqm (zero point nine zero) sizeoctagon boards (Stop), as per IRC-67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting. 1.5mm (one point five millimetre) thick supported on a mild steel angle iron post 75mm x 75mm x 6mm (seventy five into seventy five into six millimetre ) firmly fixed to the ground by means of properly designed foundation with M-15 grade (M-fifteen grade) cement concrete 450x450x600mm (four hundred fifty into four hundred fifty into six hundred millimetre) , 600mm ( six hundred millimetre) below ground level as per approved drawings and technical specification section 1700, including painting angle iron post with primes and two coats of Epoxy paint as per specification and direction of Engineer-in-Charge includingcarriage of materials within all leads, liftsand other incidental. The rate isincludingoctroi,royality, Malkana, tolltax, or other taxesimposed by the Government but excluding GST. |
| 40 | Providing and erecting direction and place identification retro-reflective sign boards, as per IRC-67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3, fixed over aluminium sheeting width, 2 mm (two milimeters) thick with areanot exceeding 0.9 sqm (zero point nine) supported on RCC Post 100 mm x 100 mm (hundred into hundred milimeters) firmly fixed to the ground by mean of properly designedfoudation with M-15 grade (M-fifteen grade) cement concrete 450x450x600mm (four hundred fifty into four hundred fifty into six hundred millimetre) , 600mm ( six hundred millimetre) below ground level as per approved drawings and technical specification section 1700, including painting angle iron post with primes and two coats of Epoxy paint as per specification and direction of Engineer-in-Charge includingcarriage of materials within all leads, liftsand other incidental. The rate is includingoctroi,royality, Malkana, tolltax, or other taxesimposed by the Government but excluding GST |
| 41 | Providing and erecting direction and place identification retro-reflective sign boards, as per IRC-67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3, fixed over aluminium sheeting width, 2 mm (two milimeters) thick with areanot exceeding 0.90 sqm (zero point nine zero) supported on mild steel iron post 75 mm x 75 mm x 6 mm, (seventy five into seventy five into six milimeters), 2 Nos. (two numbers) firmly fixed to the ground by mean of properly designedfoudation with M-15 grade (M-fifteen grade) cement concrete 450x450x600mm (four hundred fifty into four hundred fifty into six hundred millimetre) , 600mm ( six hundred millimetre) below ground level as per approved drawings and technical specification section 1700, including painting angle iron post with primes and two coats of Epoxy paint as per specification and direction of Engineer-in-Charge includingcarriage of materials within all leads, liftsand other incidental. The rate is includingoctroi,royality, Malkana, tolltax, or other taxesimposed by the Government but excluding GST |
| 42 | Providing and fixing of typical PMGSY logo sign board with Logo as per MORD specifications and drawing. With ACP Sheet 3 mm (three milimeter) thick fixed on MS Angle 25mmx 25mm x 3mm (twenty five into twenty five into three milimeters) size on back on edges. Vertical Post MS square tubes 80x80x4.80 mm (eighty into eighty into four point eight zero milimeter) thick duly embedded with base plate 200x200 x5mm (two hundred into two hundred into five milimeter) in cement concrete M-20 (M- Twenty) grade blocks of Size 450 mm x 450 mm x600 mm (four hundred fifty into four hundred fifty into six hundred milimeters), below ground level. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 and Annexure 1700.1. Retro Reflective Sheet Type IV including cutting, printing, lettering & fixing comp. in all respects. as per specification and direction of Engineer-in-Charge includingcarriage of materials within all leads, liftsand other incidental. The rate is includingoctroi,royality, Malkana, tolltax, or other taxesimposed by the Government but excluding GST |
| 43 | Providing and fixing ofPMGSY Citizen Informatory board with Logo as per MORD specifications and drawing. With ACP Sheet 4 mm (four milimeter) thick fixed on MS Angle 25mmx 25mm x 3mm (twenty five into twenty five into three milimeters) size on back on edges. Vertical Post MS square tubes 80x80x4.80 mm (eighty into eighty into four point eight zero milimeter) thick duly embedded with base plate 300x300 x5mm (three hundred into three hundred into five milimeter) in cement concrete M-20 (M- Twenty) grade blocks of Size 600 mm x 600 mm x750 mm (six hundred into six hundred into seven hundred fifty milimeters), below ground level. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 and Annexure 1700.1. Retro Reflective Sheet Type IV including cutting, printing, lettering & fixing comp. in all respects. as per specification and direction of Engineer-in-Charge includingcarriage of materials within all leads, liftsand other incidental. The rate is includingoctroi,royality, Malkana, tolltax, or other taxesimposed by the Government but excluding GST |
| 44 | Providing and laying of hot applied thermoplastic compound 2.5 mm (Two point five milimeter) thick including reflectorising glass beads @ 250 gms (two hundred fifty grams) per sqm area, thickness of 2.5 mm (two point five milimeters) is exclusive of surface applied glass beads as per IRC:35. The finished surface to be level, uniform and free from streaks & holes as per specification and direction of Engineer-in-Charge includingcarriage of materials within all leads, liftsand other incidental. The rate is includingoctroi,royality, Malkana, tolltax, or other taxesimposed by the Government but excluding GST |
| 45 | Providing and laying 8 nos. (fifteen) rumble strips covered with premix bituminous carpet, 15-20 mm (fifteen to twenty milimeter) high at centre, 250 mm (two hundred fifty milimters) wide placed at 1 m (one meter)centre-to-centre at approved locations to control speed, marked with white strips of road marking paint as per specification and direction of Engineer-in-Charge includingcarriage of materials within all leads, liftsand other incidental. The rate is includingoctroi,royality, Malkana, tolltax, or other taxesimposed by the Government but excluding GST |
| 46 | Supplying and installation of delineators (road way indicators, hazard markers, object markers), 80-100 cm high (eighty to one hundred centimetre) above ground level, painted black and white in 15 cm (fifteen centimetre) wide strips, fitted with 80 x 100 mm (eighty into one hundred millimetre) rectangular or 75 mm dia (seventy five millimetre diametre) circular reflectorised panels at the top, buried or pressed into the ground and conforming to IRC-79 and the drawings and specifications complete as per direction of Engineer – in- Charge including carriage of materials within all leads, liftsand other incidental . The rate is includingoctroi,royality, Malkana, toll tax, orother taxes imposed by the Government but excluding GST. |
| 47 | Providing and fixing of PMGSY (Maintenance Information board), as per MORD Specifications and drawings made of 3.0mm (three point zero millimetre)on back on edges, Vertical post MS square tubes 80x80x4.80 mm (Eighty inti eighty into four point eight zero milimeter) thick with base plate 300x300x5mm (three hundred into three hundred into five milimeter) duly embeded in cement concrete M-20 grade (M-Twenty) blocks of size 600mm x 600mm x750mm (six hundred into six hundred into seven hundred fifty milimeter), below ground level. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 and Annexure 1700.1. Retro Reflective Sheet Type IV including cutting, printing, lettering & fixing comp. in all respects. thick ACP sheetsas per specification and direction of Engineer-in-Charge includingcarriage of materials within all leads, liftsand other incidental. The rate is includingoctroi,royality, Malkana, tolltax, or other taxesimposed by the Government but excluding GST |
| 48 | Providing and Fixing pavement marker(Cat eyes) made out of ABC 3 M (three) plastic of size 128x110x29.5 mm ( one hundred twenty eight into one hundred ten into twenty nine decimal five millimetres) without nail having 50mm ( fifty millimetres) stem of ABS. The pavement marker shall be installed with epoxy ABS as per specification including carriage of materials and equipmentwith all mode of transportation and as per direction of Engineer – in- Charge including carriage of materials within all leads, liftsand other incidental . The rate is includingoctroi,royality, Malkana, toll tax, orother taxes imposed by the Government but excluding GST. |
