|
| 1 | RESEARCH LAB, MECHANICAL ENGINEERING, SMVD UNIVERSITY KATRA |
| 2 | TABLE FOR CABIN - Providing and placing of Main Table with overall size of table shall be 1500 Width mm X 750 Depth mm X 740 Height mm that is to be assembled at site. The construction of the main table shall be free standing structure constructed with the help of minifix dowels and pins. The work top shall have the size 1500mm X 750mm made up of 25mm thick particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The table top profile shall be in rectangle shape with front and back full round post form and other edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. The table top shall be supported over particle board base gable end. The end wall of the table on the side shall be topped by gable end. The gable end shall be made up of 25mm thick particle board and profile shall be in linear shape with front and back full round post form and other edge with appropriate PVC edge banding. The table shall be clad with 18mm thick modesty panel which provide structural support for the table. It should be 18mm thick pre-laminated particle board with appropriate PVC edge banding connected with both end. There shall be buffers provided at the base to avoid scratches on the floor. A mobile pedestal shall be provided with an overall size 400mm X 450mm X 660mm. The pedestal shall be made up of Pre-laminated particle board of grade II of IS 12823. Pedestal side, back, top, facia shall be 18mm thick and drawer base shall be 9mm thick. The pedestal shall have 3 nos. of drawer i.e. 2 box drawer and 1 filing drawer. The drawer shall be operated with SS handle and easily close & open with the assistance of roller channel and ball bearing channel having to enable smooth operation. The drawer shall have central locking mechanism in which all the drawer shall be synchronized locked with one single key. The pedestal shall be mounted over 50mm injection moulded nylon castor. Dimensions Tolerance + 20 mm. |
| 3 | TABLE FOR FACULTY CABIN - Providing and placing of Main Table with overall size of table shall be 2000 Width mm X 750 Depth mm X 740 Height mm that is to be assembled at site. The construction of the main table shall be free standing structure constructed with the help of minifix dowels and pins. The work top shall have the size 1500mm X 750mm made up of 25mm thick particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The table top profile shall be in rectangle shape with front and back full round post form and other edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. The table top shall be supported over particle board base gable end. The end wall of the table on the side shall be topped by gable end. The gable end shall be made up of 25mm thick particle board and profile shall be in linear shape with front and back full round post form and other edge with appropriate PVC edge banding. The table shall be clad with 18mm thick modesty panel which provide structural support for the table. It should be 18mm thick pre-laminated particle board with appropriate PVC edge banding connected with both end. There shall be buffers provided at the base to avoid scratches on the floor. A mobile pedestal shall be provided with an overall size 400mm X 450mm X 660mm. The pedestal shall be made up of Pre-laminated particle board of grade II of IS 12823. Pedestal side, back, top, facia shall be 18mm thick and drawer base shall be 9mm thick. The pedestal shall have 3 nos. of drawer i.e. 2 box drawer and 1 filing drawer. The drawer shall be operated with SS handle and easily close & open with the assistance of roller channel and ball bearing channel having to enable smooth operation. The drawer shall have central locking mechanism in which all the drawer shall be synchronized locked with one single key. The pedestal shall be mounted over 50mm injection moulded nylon castor.Dimensions Tolerance + 20 mm. |
| 4 | CHAIR FOR CABIN & FACULTY ROOMS - Supplying and placing ergonomically designed, comfortable & aesthetically appealing Medium back chair. The seat shall be made of 15mm thick hot pressed malaysian plywood with HR polyurethane foam 50mm thick having density 40kg/m³ upholstered with leatherite tapestry in black colour with 0.8mm thick and 535 GSM and the back shall be made of double layered malaysian moulded hot pressed plywood (12+6)mm thick with HR polyurethane foam 30mm thick having density 32kg/m³ upholstered with leatherite tapestry in black colour with 0.8mm thick and 535 GSM. Seat and back shall be joined with HR steel sheet. The armrest shall be used PP arm fixed type completely joint with seat. The chair shall have synchro knee tilt revolving mechanism with four position locking and tilt tension adjustment. The pneumatic seat height adjustable 100mm with BIFMA standard class-3 gaslift. The Pedestal shall be made up of injection moulded black nylon having pitch circle Dia 700 mm fitted with 5 nos. 50mm twin wheel castors which shall be made of injection moulded black nylon 30% glass filled having self lubricating property for friction free movemen with BIFMA standards. The Seat size shall be 480±10mm(W) X 495±10mm(D) and back size shall be 590±10mm(H) from seat & overall height = 1030±10mm. Dimensions Tolerance + 20 mm. |
| 5 | EXECUTIVE TABLE FOR CABIN 3 - Supplying & installing of table with ERU and pedestal having following specifications. The table shall be supplied in completely knock down conditions with an overall size W1800 X D1800 X H750mm that is to be assembled at site. The worktop shall have the size 1800 X 900mm made up of 50mm thick PLPB with approved laminate and finish as per approved shade. The top edge should cladded with 1.2mm thick extruded aluminium section all around the worktop and die cast end caps on joints for better strength of the table. The profile shall be in rectangle shape and enclosed by flapper box for electric provision. The top shall be supported on gable end. The end wall of the table on the side shall be topped by gable end. It should be 50mm thick Medium Density Fibre-board linear in profile and the edges cladd with extruded aluminium profile. The table shall be clad with 18mm thick modesty panel which provide structural support for the table. It should be 18mm thick particle board and shall be linear in profile. The table shall be supplied with credenza unit with an overall size 900mm X 450mmmm that shall be constructed from Pre-laminated particle board of grade II of IS 12823 with 25mm thick top and other parts 18mm thick like shutter, back, facia etc. The drawer and shutter shall be operated with ball bearing sliding channel and concealed crank hinge. G-profile Aluminium handle shall be supplied for ease of opening. The ERU unit shall be mounted on 38mm Dia. leg. Fixed pedestal shall be supplied with an overall size 380mm X 400mm X 600mm. The pedestal shall be made up of Pre-laminated particle board of grade II of IS 12823. Top shall be 25mm thick, side, back, facia shall be 18mm thick. The pedestal shall have 2 nos. of drawer having same. The drawer shall be operated with ball bearing sliding channel to enable smooth operation. Aluminium handle shall be provided for ease of opening. For locking provision central lock mechanism shall be given in which all the drawer shall be synchronized locked with one single key. The pedestal shall be mounted on Aluminium round leg. Dimensions Tolerance + 20 mm. |
| 6 | EXECUTIVE CHAIR FOR CABIN 3- Providing and supplying a high back chair with ergonomic design, comfortable & aesthetically appealing. The seat and back frame shall be made up of the combination of 15mm thick hot pressed commercial plywood and ply-board padded with high resilience polyurethane foam (50+25+30)mm thick having density (40, 32 & 32)kg/m³ in seat and (30+25)mm thick having density (32, 32)kg/m³ in back. The same shall be upholstered with leatherite tapestry 0.8mm thick and 535 GSM. The backrest shall be made by keeping the natural curvature of the spine for lumbar support which helps to provide full back support as well as head support. Seat and back shall be covered with polished wooden at both side for decorative appearance. The chair shall be supplied with natural wood arm having melamine polish and die cast aluminium end caps. For seating durability the chair shall have torsion bar 360 degree revolving mechanism with upright position locking and tilt tension adjustment. The Hydraulic seat height adjustment for healthy seating, user can adjust seat height up to 65mm with BIFMA standard class-3 gas-lift to suit them using the lever under the seat. The gas-lift mechanism should be tested as per ANSI/BIFMA X5.1-2011 standards. The Pedestal should have metal insert CRCA covered with natural wood having pitch circle dia. 630 mm fitted with 5 nos. twin wheel castors. The castors of the chair should be injection moulded in black 30% glass filled nylon, confirming to ANSI/BIFMA standards X5.1-2011 tested to perform 98,000 cycles with 250lbs load. The seat size shall be 510±10 mm(D) X 510±10 mm(W) and back size shall be 525±10 mm(W) X 710±10 mm(H) from seat. Overall height shall be = 1170±10 mm & overall width/depth = 740±10 mm.. Dimensions Tolerance + 20 mm. |
| 7 | VISITOR CHAIR FOR CABIN 3 - Providing and supplying a high back chair with ergonomic design, comfortable & aesthetically appealing. The seat and back frame shall be made up of the combination of 15mm thick hot pressed commercial plywood and ply-board padded with high resilience polyurethane foam (50+25+30)mm thick having density (40, 32 & 32)kg/m³ in seat and (30+25)mm thick having density (32, 32)kg/m³ in back. The same shall be upholstered with leatherite tapestry 0.8mm thick and 535 GSM. The backrest shall be made by keeping the natural curvature of the spine for lumbar support which helps to provide full back support as well as head support. Seat and back shall be covered with polished wooden at both side for decorative appearance. The chair shall be supplied with natural wood arm having melamine polish and die cast aluminium end caps. The frame structure shall be cantilever support type made of MS CRCA powder coated 50-60µ (DFT) thick round pipe of dia. 28.5mm with 2mm thick. There shall be PPCP shoe provided at the base to avoid scratches on the floor. The Seat size shall be 480±10 mm(D) X 510±10 mm(W) and back size shall be 520±10 mm(W) X 580±10 mm(H) from seat. Overall height shall be = 1030±10 mm, overall depth = 620±10 mm & overall width = 620±10 mm. Dimensions Tolerance + 20 mm. |
| 8 | 2-SEATER SOFA FOR CABIN 3 - Supplying and placing two seater sofa that shall be constructed from natural hard wood and commercial plywood having inner frame. The thickness of the wood should allow for the heavy tension webbing. The sofa shall have spring attached and also be padded. The frame shall be padded with high resilience polyurethane foam having density 40Kg/m³ in seat and 32Kg/m³ in back. There shall be cushion arm provided padded with high resilience polyurethane foam having density 40Kg/m³. The complete structure shall be upholstered with leatherite tapestry 1±0.2 mm thick and 571 GSM. The understructure shall consist of SS 202 grade loop leg with shiny chrome finish having cross-section area 40mm X 20mm with 1.6mm thick. There shall be shoe provided at the bottom to avoid scratches on the floor. The seat size shall be 510±10 mm(D) X 1040±10 mm(W), seat height = 435±10 mm, overall width = 1360±10 mm, overall depth = 770±10 mm & overall height = 800±10 mm. Dimensions Tolerance + 20 mm. |
| 9 | CENTRE TABLE FOR CABIN 3 - Providing and supplying centre table with an overall size 1200mm X 600mm X 430mm. The top and side cladding shall be made up of 36mm thick pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. Extruded aluminium section shall be inserted within side corner edge at both side of the table. There shall be leveller shoe provided at the bottom. Dimensions Tolerance + 20 mm. The participating brand must have all the prevalent quality & safety related certifications like ISO: 9001, ISO:50001, ISO:14001 & ISO: 45001 by NABCB, BIFMA Membership, AIOTA & Greenguard Certification has to be submitted. |
| 10 | CORNER TABLE FOR CABIN 3 - Providing and supplying centre table with an overall size 600mm X 600mm X 430mm. The top and side cladding shall be made up of 36mm thick pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. Extruded aluminium section shall be inserted within side corner edge at both side of the table. There shall be leveller shoe provided at the bottom. Dimensions Tolerance + 20 mm. |
| 11 | WOODEN ALMIRAH FOR CABIN FACULTY ROOM & HALL - Supplying & placing storage unit with an overall size 900mm X 450mm X 2000mm. Storage shall be made up of Pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. All profile i.e. side, back, top, shutter, skirting shall be 18mm thick and the edges shall be sealed with thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. The storage shall have 3 nos. of adjustable shelf and 1 fixed shelf. 2 normal shutter and 2 glass shutter shall be provided for closing and opening the shutter. The glass shutter shall be made 4mm clear glass insert within aluminium profile. The shutter shall be operated with concealed crank hinge with SS handle as well as MP lock mechanism. To protect the wall from kicks, abrasion and serve as a decorative moulding, skirting shall be provided at bottom. There shall be buffers provided at the base to avoid scratches on the floor. Dimensions Tolerance + 20 mm. |
| 12 | STEEL ALMIRAH FOR CABIN FACULTY ROOM & HALL - Providing, supplying and placing steel almirah in perfectly upright and straight position. The overall size of the Almirah shall be 915mm (W) X 485mm (D) X 1980mm (H) including legs. It should be supplied with 4 nos. of adjustable shelves i.e. 5 loading compartments. All components shall be made of 0.8mm thick high yield strength CRCA sheet of grade ‘D’ confirming to IS: 513. Stiffeners shall be provided in shelf & door. The steel hinged door shall be provided with locking mechanism which is assembled with bolt arrangement. The shelves shall have folded constructions which have intrinsic rigidity and high load carrying capacity. Uniformly distributed load capacity per each shelf shall be 40kg maximum. The complete steel structure shall be constructed by welding and provide finishing with epoxy polyester powder coated to be thickness 50-60µ. Dimensions Tolerance + 20 mm. |
| 13 | STEEL BOOKCASE FOR CABIN & FACULTY ROOM - Providing and supplying metal book case with an overall size 915 mm (W) X 320 mm (D) X 1750mm (H). The book case shall be supplied with 4 nos. of individual compartments. All components shall be made of 0.8mm high yield strength CRCA sheet of grade ‘D’ confirming to IS: 513. Each door shall have individual locking provision and 4 mm thick transparent glass for clear inside vision secured in a metal frame through rubber gasket. Each door shall have scissor mechanism for receding inside the top of respective compartment which ensures parallel & smooth movement. Each door shall have plastic side end caps as handle which is easy to grip. Each compartment has a storage shelf having Uniformly Distributed Load Capacity of each shelf is 40 Kg maximum. The finish is Epoxy Polyester Powder coated to the thickness of 40-60µ. Adjustable leveler shall be provided with metal insert to resist scratches on the floor and also level & support structure.Dimensions Tolerance + 20 mm. |
| 14 | VISITOR CHAIR FOR CABIN & FACULTY ROOMS - Providing and supplying visitor chair with ergonomic design for user comfort. The seat and back shall be made of hot pressed commercial plywood padded with high resilience polyurethane foam having density 40Kg/m³ in seat and 32kg/m³ in back. The same shall be upholstered with leatherite tapestry 0.8mm thick. The backrest of the chair shall be made by keeping the natural curvature of the spine for lumbar support with the assistance of cushion. The armrest shall be cushion arm with leatherite covering. The frame structure shall be cantilever support type made up of MS/CRCA chrome plated circular pipe having dia. 28.6mm. There shall be co-polymer polypropylene shoe provided at the base to avoid scratches on the floor as well as uneven surfacing. The seat size shall be 480±10 mm(W) X 460±10 mm(D) and back size shall be 460±10 mm(W) X 580±10 mm(H) from seat & overall height = 1020±10 mm, overall width = 610±10 mm & overall depth = 670±10 mm. Dimensions Tolerance + 20 mm. |
| 15 | MODULAR CONFERENCE TABLE - Supplying & Placing Conference table in completely knock down conditions with an overall size 2400mm X 1200mm X 750mm that is to be assembled at site. The table top shall have same size made up of 25mm thick Pre-laminated particle board of grade II of IS 12823 with one side laminate and finish as per approved shade. The table top profile shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree celsius. Single sided flapper box shall be enclosed at table top that houses video, audio, data and power connection discretely. The end wall of the table on the side shall be topped by gable end. The gable end shall have the size 900mm X 570mm. The gable end shall be made up of 25mm thick Pre-laminated particle board and profile shall be in linear shape with appropriate PVC edge banding. The table shall be clad with 18mm thick modesty panel which provide structural support for the table. The modesty panel shall be 18mm thick pre-laminated particle board with appropriate PVC edge banding connected with both end. The table shall be supported on SS pipe leg 202 grade. It shall have cross section area 80mm X 20mm. There shall be buffers provided to avoid scratches on the floor. The table connections have to be made in such a way that no gap should be seen in between. Table shall be provide a Flip up/ Pop up box (without wires) 01 no. Dimensions Tolerance + 20 mm. |
| 16 | MAIN CHAIR FOR CONFERENCE TABLE - Providing and supplying a high back chair with ergonomic design, comfortable & aesthetically appealing. The seat and back shall be made of natural wood and combination of (18+6)mm thick double layered moulded commercial plywood padded with high resilience polyurethane foam 70mm thick having density 40kg/m³ in seat and 70mm thick having density 32kg/m³ in back. The same shall be upholstered with leatherite tapestry 0.8mm thick and 535 GSM. The backrest shall be made by keeping the natural curvature of the spine which helps to provide lumbar support as well as head support. The chair shall be supplied with polypropylene chrome cushion arm with leatherite covering top pivot joint with back. For seating durability the chair shall have torsion bar 360 degree revolving mechanism with upright position locking and tilt tension adjustment. The pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 65mm with BIFMA standard class-3 gas-lift to suit them using the lever under the seat. The gas-lift mechanism should be tested as per ANSI/BIFMA X5.1-2011 standards. The Pedestal should have five legged injection moulded polypropylene with chrome having pitch circle dia. 700 mm fitted with 5 nos. twin wheel castors. The castors of the chair should be injection moulded in black 30% glass filled nylon, confirming to ANSI/BIFMA X5.1-2011 standards tested to perform 98,000 cycles with 250lbs load. The seat size shall be 510±10 mm(D) X 530±10 mm(W) and back size shall be 500±10 mm(W) X 720±10 mm(H) from seat. Overall height shall be = 1180±10 mm, overall depth = 670±10 mm & overall width = 710±10 mm. Dimensions Tolerance + 20 mm. |
| 17 | CHAIRS FOR CONFERENCE TABLE - Providing and supplying a medium back chair with ergonomic design, comfortable & aesthetically appealing. The seat and back shall be made of natural wood and combination of (18+6)mm thick double layered moulded commercial plywood padded with high resilience polyurethane foam 70mm thick having density 40kg/m³ in seat and 70mm thick having density 32kg/m³ in back. The same shall be upholstered with leatherite tapestry 0.8mm thick and 535 GSM. The backrest shall be made by keeping the natural curvature of the spine which helps to provide lumbar support. The chair shall be supplied with polypropylene chrome cushion arm with leatherite covering top pivot joint with back. For seating durability the chair shall have torsion bar 360 degree revolving mechanism with upright position locking and tilt tension adjustment. The pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 65mm with BIFMA standard class-3 gas-lift to suit them using the lever under the seat. The gas-lift mechanism should be tested as per ANSI/BIFMA X5.1-2011 standards. The Pedestal should have five legged injection moulded polypropylene with chrome having pitch circle dia. 700 mm fitted with 5 nos. twin wheel castors. The castors of the chair should be injection moulded in black 30% glass filled nylon, confirming to ANSI/BIFMA X5.1-2011 standards tested to perform 98,000 cycles with 250lbs load. The seat size shall be 510±10 mm(D) X 530±10 mm(W) and back size shall be 500±10 mm(W) X 520±10 mm(H) from seat. Overall height shall be = 980±10 mm, overall depth = 670±10 mm & overall width = 710±10 mm. Dimensions Tolerance + 20 mm. |
| 18 | DISCUSSION TABLE- Supplying & Placing Conference table in completely knock down conditions with an overall size Dia. 900mm X 750mm that is to be assembled at site. The table top shall be made up of 25mm thick Pre-laminated particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The table top profile shall be in circular shape and the edges shall be sealed with 2mm thick PVC edge banding. The table understructure shall be a combination of MS powder coated and Pre-laminated particle board. There shall shoe provided at the base to avoid scratches on the floor. Table shall be provide a Flip up/ Pop up box (without wires) 01 no. Dimensions Tolerance + 20 mm. |
| 19 | CHAIR FOR DISCUSSION TABLE - Supplying and placing Lounge Chair. The seat shall be made of 12 mm thick hot pressed plywood upholstered with high resiliance moulded polyurethane foam 50mm thick having density 40kg/m³ with leatherite tapestry 0.8mm thick 535 GSM and the back shall be made of Wooden Frame upholstered with high resiliance moulded polyurethane foam 25mm thick having density 32kg/m³ with leatherite tapestry 0.8mm thick 535GSM. The frame structure shall be 4 legs support type made up of Reducing Pipe Frame Powder Coated tubular pipe having cross-section area Dai 19mm thick. The seat size shall be 430±10 mm (D) X 450±10 mm (W) and back size shall be 500±10 mm (W) X 400±10 mm (Ht) from seat. Overall height shall be = 840±10 mm, overall depth = 540±10 mm & overall width = 580±10 mm. Dimensions Tolerance + 20 mm. |
| 20 | MODULAR WORKSTATION FOR HALL - Supplying & Placing modular workstation in completely knock down conditions with SIZE :- W1200 X D600 X H750/1200MM that is to be assembled at site.The construction of the main table shall be free standing structure. The worktop shall have the size 1200mm X 600mm made up of 25mm thick Re Lam Particle Board with laminate and sealed with 2mm thick PVC edge banding. A pullout keyboard trey shall be provided of 18mm thick PLPN. PARTITION :- 60mm thick panel based partition of height 1200mm having provision of fabric / soft pin up board/ Laminate / race way. WORKTOP :- 25mm thick PLPB board with pvc edge banding. All Aluminum parts shall be pretreated and duly powder coated of 40µ-50µ thick. Raceway shall be provided of aluminum below the work top as per requirement for inlaying the electrical management and carrying the wire horizontally. The exposed vertical and horizontal faces of the frames shall be snap fitted with curve trims. The trims shall be made of aluminum extrusions of size 60x19mm with 1.5mm thick and should be covered with Die Cast End caps on joints, 2 ways, 3 ways & 4 ways caps as required. Wire management partition shall have concealed wire management capabilities and shall be engineered for responsive and safe operations of power, telecommunications and data (LAN) and has separate components for electrical, data and telephone cables having adequate capability of both the vertical and horizontal wire movements. Slots/cutouts shall be provided on raceways to fix all electrical and data points. MOBILE PEDESTAL :- (2D + 1F) 18mm thick PLPB board with pvc edge banding, Mobile pedestal shall be provided with an overall size 400mm X 450mm X 680mm. Pedestal side, back, top, facia shall be 18mm thick and drawer base shall be 9mm thick. The pedestal shall have 3 nos. of drawer i.e. 2 box drawer and 1 filing drawer. The drawer shall be operated with SS handle and easily close & open with the assistance of roller channel and ball bearing channel to enable smooth operation. The drawer shall have central locking mechanism in which all the drawer shall be synchronized lock with one single key. A nylon castor based CPU unit shall be provided with 18mm thick PLPB. Dimensions Tolerance + 20 mm. |
| 21 | CHAIR FOR WORKSTATIONS - Providing and supplying medium back chair with ergonomic design, comfortable & aesthetically appealing. The seat shall be made of 18mm thick hot pressed commercial plywood upholstered with high resilience moulded polyurethane foam 50mm thick having density 40kg/m³ with foam net tapestry 0.9mm thick and 300 GSM and the back shall be made of injection moulded polypropylene net cover upholstered with breathable mesh tapestry. The backrest of the chair shall be made by keeping the natural curvature of the spine with adjustable lumbar support. The chair shall be supplied with injection moulded PU adjustable arm completely joint with seat. For seating durability the chair shall have ACTICE BIO-SYNCHRO mechanism with upright position locking and tilt tension adjustment. The pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 100mm with BIFMA standard class-3 gas-lift to suit them using the lever under the seat. The gas-lift mechanism should be tested as per ANSI/BIFMA X5.1-2011 standards. The Pedestal should have five legged made of die cast aluminium having pitch circle dia. 700 mm fitted with 5 nos. twin wheel castors. The castors of the chair should beinjection moulded in 30% glass filled nylon, confirming to ANSI/BIFMA standards X5.1-2011 tested to perform 98,000 cycles with 250lbs load. The seat size shall be 520±10 mm(W) X 500±10 mm(D) and back size shall be 495±10 mm(W) X 610±10(H) from seat & overall height = 1010±10 mm. Dimensions Tolerance + 20 mm. The participating brand must have all the prevalent quality & safety related certifications like ISO: 9001, ISO:50001, ISO:14001 & ISO: 45001 by NABCB, BIFMA Membership, AIOTA & Greenguard Certification has to be submitted. |
| 22 | 2 DOOR LOCKERS FOR HALL - Providing and Placing in position Personal Locker Unit shall be of dimensions 380mm(W) X 450mm(D) X 1800mm(H) having 2 locker unit. Each locker shall have 1 nos. of Hanging rod. Locking shall have cam lock with lock lever plus option. Material shall be CRCA 0.8 mm thickness. Shelf shall be uniformly distributed load capacity per each shelf level is 35 Kg maximum. Finish shall be epoxy polyester powder coated to the thickness of 50 microns. Handle/Label holder shall be aesthetically appealing Snap fit ABS plastic handle. Ventilation shall be attractive punched pattern for ventilation. Dimensions Tolerance + 20 mm. |
| 23 | 3 DOOR LOCKERS FOR HALL - Providing and Placing in position Personal Locker Unit shall be of dimensions 380mm(W) X 450mm(D) X 1800mm(H) having 3 locker unit. Locking shall have cam lock with lock lever plus option. Material shall be CRCA 0.8 mm thickness. Shelf shall be uniformly distributed load capacity per each shelf level is 35 Kg maximum. Finish shall be epoxy polyester powder coated to the thickness of 50 microns. Handle/Label holder shall be aesthetically appealing Snap fit ABS plastic handle. Ventilation shall be attractive punched pattern for ventilation. Dimensions Tolerance + 20 mm. |
| 24 | 4 DOOR LOCKERS FOR HALL - Providing and Placing in position Personal Locker Unit shall be of dimensions 380mm(W) X 450mm(D) X 1800mm(H) having 4 locker unit. Locking shall have cam lock with lock lever plus option. Material shall be CRCA 0.8 mm thickness. Shelf shall be uniformly distributed load capacity per each shelf level is 35 Kg maximum. Finish shall be epoxy polyester powder coated to the thickness of 50 microns. Handle/Label holder shall be aesthetically appealing Snap fit ABS plastic handle. Ventilation shall be attractive punched pattern for ventilation. Dimensions Tolerance + 20 mm. |
| 25 | LAB OVER HEAD UNIT- Providing and fixing Lab Over Head Unit with overall dimensions 750(W)mm x 320(D)mm x 675mm(H). Over Head Unit shall be Welded body with load bearing members such as top, bottom and stiffeners made of 0.8mm thick CRCA Sheet. The storage unit shall be provided with a shelf made of 0.8mm thick CRCA sheet. Each shelf shall have load carrying capacity of 30-40 kgs. MP with 180 degree cam lock. Semi recessed handle and SS hinge. Shutter shall be provided with a MP lock. |
| 26 | LABORATORY LAB STOOLS- Providing and Placing in position Ht. Adjustable Stool with Back. The seat shall be made up of 1.2±0.1cm thick flat plywood and with moulded Polyurethane foam and are upholstered with replaceable synthetic leather covers. The dimensions of Seat shall be Diameter 40.0 cm and Adjustments are 360° Revolving type. The back foam shall be designed with contoured Lumbar support for extra comfort. The upholstery shall be available in synthetic leather. The dimensions of Back shall be 45.0 cm (W) covered with polyurethane foam. The HR polyurethane Foam shall be moulded with density = 40 +/-2 kg/m3. The five-prong pedestal shall be fabricated from 0.2 ± 0.02 cm thick HR sheet ( IS : DD 1079/ HR ), Powder coated ( DFT 40-60 microns ). The twin wheel castors shall be injection moulded in Black Nylon. Dimensions Tolerance ±20 mm. Please Enable Macros to View BoQ information |
