|
| 1 | Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for complete all as specified & directed. |
| 2 | Demolition of cement concrete (unreinforced) in ground floors and pavings not exceeding 15cm thickness (below or above ground level)complete all as specified & directed. |
| 3 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) of any thickness and in any positionand removing serviceable tiles to store and rubbish off the premises complete all as specified & directed. |
| 4 | Dismantling and breaking up drain pipes (salt glazed ware, AC, reinforced concrete, PVC or Cast iron) set in cement mortar of size 100mm/75mmfixed over wall or in floor including clamps etc., complete all as specified & directed. |
| 5 | Taking down cement rendering/plastering of any thickness and of any description including raking out joints, hacking for key, scrubbing down with water etc., over wall or ceiling surfaces complete all as specified & directed. |
| 6 | Taking down chowkhats or frames not exceeding 1.5 Sqm each with shutters(without taking off shutters from the frames) including hold fasts from wall and making good in cement mortar 1:4 complete all as specified & directed. |
| 7 | Taking down chowkhats or frames exceeding 1.5 Sqm each but not exceeding 4 Sqm each with shutters(without taking off shutters from the frames) including hold fasts from wall and making good in cement mortar 1:4 complete all as specified & directed. |
| 8 | Taking down shutter of any description and material exceding 1.00 Sqm but not exceeding 2.00 Sqm each complete all as specified & directed. |
| 9 | S&F solar control film 50 micron reflective type/frosted sticked to glass panes as per instructions of manufacturers complete all as specified & directed. |
| 10 | M&Lfor providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement complete all as specified & directed. |
| 11 | S&Fin repairs counter/table top vitreous China wash hand basin, of size 550X400X160mm white in colour,and 32mm bore dia CP finish copper alloy waste fitting/coupling, 32mm bore dia bottle trap including cutting for and pinning complete all as specified & directed. |
| 12 | M&L for preparation ofold decorated ceiling surfacesand applying one coat of white washincluding necessary filling of voids with wall care putty complete all as specified & directed. |
| 13 | S&F in repairs5.5 mm thick bevelled edge mirror of selected quality glass ,mounted on 17-18 mm thick WPC board fixed to wooden plugs with chromium plated \"D\" cut accessories, screws and washer complete all as specified & directed. |
| 14 | S&F12mm thick toughned glass fixed in windows/stair case railing of any material and description of required size, the edges of glass to be finished as clear polish including necessary cutting for nut bolt/screws/patch fittings etc complete all as specified and directed |
| 15 | Dismantalling of wall and ceilingboards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets and frame work complete all as specified and directed |
| 16 | S&F Gypsum Board 12mm thick in ceiling fixed with screw as per manufacturers instructions(metal frame work paid separately) including two coats of oil bound distemper duly filled the voids with wall care putty including preparation of surface complete all as specified and directed |
| 17 | S&FGl frame work (size of grid not exc. 605mmX605mm) for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre. |
| 18 | S&F in repairs fancy type 15mm bore dia long body fancy type bib tap chromium plated cast copper alloy, screwed down, high pressure, screwed ends for water pipe fitting or for unions including CP finish cup washer/wall flange complete all as specified & directed. |
| 19 | S&F in repairsfancy type 15mm bore dia short body fancy type bib tap chromium plated cast copper alloy, screwed down, high pressure, screwed ends for water pipe fitting or for unions including CP finish cup washer/wall flange complete all as specified & directed. |
| 20 | S&F in repairs15mm bore dia fancy angle stop valve, chromium plated, cast copper alloy,screwed down, high pressure, screwed ends for water pipe fitting or for unions including CP finish cup washer/wall flange complete all as specified & directed. |
| 21 | S&F in repairsPVC connection 15mm size with PTMT nuts of length 450mm complete all as specified & directed. |
| 22 | S&F in repairsPVC connection 15mm size with PTMT nuts of length 600mm complete all as specified & directed. |
| 23 | S&F in repairs10 litre capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float, and handle/push type, including 32mm bore dia PVC long/short flusing pipe andbrackets complete all as specified & directed. |
| 24 | S&F in repairsfancy type square shape of minimum size 100mmX100mm swivel shower of cast stainless steel, including CP finish shower rod (long) and cup washer/wall flange for fixing with 15mm bore dia pipe/fittings complete all as specified & directed. |
| 25 | S&F in repairs tubular brass chromium plated Towel rail 20mm dia \"D\" type 60cm long between flanges complete all as specified & directed. |
| 26 | S&F in repairs CP finish soap dish cast stainless steelfixed to plugs complete all as specified & directed. |
| 27 | S&F in repairs15mmdia, cast copper alloy CP finish wall mixer (3 in 1)cast copper alloy, for mixing hot & cold water screwed down for water pipe/fittings including hand shower with flexible pipe complete all as specified & directed. |
| 28 | S&F in repairswall mounted Sheet glass shelf assembly consisting of acrylic sheet shelf 12cm wide with chromium plated bracket guard and railing, 60cm long complete all as specified & directed. |
| 29 | S&F in repairswall mounted corner Sheet glass shelf assembly consisting of acrylic sheet shelf 20cm wide and 30cm long each side with chromium plated bracket guard and railing, complete all as specified & directed. |
| 30 | Taking down shutter of any description and material (Wooden,Aluminium/UPVC) from frame/chowkhat exceeding 1Sqm but not exceeding 2Sqm each and re-fix in the same opening after necessary repairing, ease and adjust, cutting, grinding, adjusting,including using new nails/screws complete all as specified and directed. Note: Material required other than mentioned in this item for repairing shall be paid under respective supply only item. |
| 31 | Taking down shutter of any description and material (Wooden,Aluminium/UPVC) from frame/chowkhat not exceeding 1Sqm each and re-fix in the same opening after necessary repairing, ease and adjust, cutting, grinding, adjusting,including using new nails/screws complete all as specified and directed. Note: Material required other than mentioned in this item for repairing shall be paid under respective supply only item. |
| 32 | S&F in replacement of old defective wire cloth with new stainless steel wire cloth 0.36mm dia of wire and average width of aperature 1.40mm/nylon material and fixed in UPVC/wooden/steel door/window shutters including new second class hard wood beading of required size to secure the wire cloth/mesh/welding/nut bolt complete all as specified and directed. |
| 33 | S&F in repairs4mm thick sheet glass, ordinary quality, in squares, pane including taking down from wooden/steel/aluminium shutter of any description including using necessary size of second class hard wood beading to secure the glasss complete all as specified and directed. |
| 34 | S&F100mm medium weight mild steel butt hinges complete all as specified & directed. |
| 35 | S&F100mm medium weight stainless steel butt hinges including necessary stainless steel screws of reqd size complete all as specified & directed. |
| 36 | S&F in repairs 150mm long cast type anodised aluminium handle complete all as specified & directed. |
| 37 | Supply only 150mm long cast type anodised aluminium handlecomplete all as specified & directed. |
| 38 | S&F in repairsfloor door stopper of aluminum alloy body and tongue, anodized with hard drawn steel spring and vulcanised rubber piece complete all as specified & directed. |
| 39 | Supply only floor door stopper of aluminum alloy body and tongue, anodized with hard drawn steel spring and vulcanised rubber piece complete all as specified & directed. |
| 40 | S&F in repairsfor 250mm length of bolt, Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified & directed. |
| 41 | S&F in repairs200mm long aluminium, anodised barrel tower bolts of extruded section complete all as specified & directed. |
| 42 | Supply only 200mm length of bolt, aluminium anodised barrel tower bolts of extruded section, complete all as specified & directed. |
| 43 | S&F250mm length of bolt, Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified & directed. |
| 44 | S&FFactory made single extruded WPC (Wood Polymer Composite) solid one side decorated and other side plain flush door shutter of 30mm thickness comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. (Note: stainless steel butt hinges and necessary S S screws shall be paid separately) complete all as specified & directed. |
| 45 | S&F17mm to 18mm thick WPC board of approved make of one side prelam/rigidlam and other side plain colour fixed with screws, solvent cement/adhesive to make cup board/ cabinet shutters/drawer front/sides, partitions, shelves etc. including 1mm thick PVC lipping/beading fixed with solvet over edges of ply of required width and colour complete all as specified and directed. |
| 46 | S&F sleek soft hydraulic auto closing 3D (Big bend/middle bend/straight arm type) stainless steel finish hinges openable of 0 or 15 degree crank for cup board/ cabinet shutters (sample available in GE Office) complete all as specified and directed. |
| 47 | Supplying and laying of 25mm nominal size CPVC pipes SDR 11 including plain & brass threaded special fittings of same size or of reducer or enlarged size, fixed to wall/ceiling or laying in floors and necessary cutting/chases in wall/floor of any description and their making good including taking down of existing tubing complete all as specified and directed. |
| 48 | Supplying and laying of 20mm nominal size CPVC pipes SDR 11 including plain & brass threaded special fittings of same size or of reducer or enlarged size, fixed to wall/ceiling or laying in floors and necessary cutting/chases in wall/floor of any description and their making good including taking down of existing tubing complete all as specified and directed. |
| 49 | S&F in repairs chowkats 30mm thick factory made wire mesh solid WPC door shutter consisting of Density 650 Kg /Cum manufactured by an ISO-9001-2015 certified Company , Door to be panelled with SS mosquito Mesh and XTN aluminium Mesh for additional strength and safety purpose. (confirming as per IS:4020). The door should be water proof, termite proof, fire retardant and having screw holding capacity. Door to be fixed to frame with 3 nos. M.S powder coated butt hinges size 100mm*25mm*2mm and 32mm long steel screws.Other hardwares should be fixed with 19x6mm size steel screws etc. Complete as per direction of Engineer-in -charge, manufacturer\"s specification & drawings. |
| 50 | S&F in repairshigh grade plastic, bath room mirror cabinet of size 450mmX350mm & 3mm thick looking mirror of make Modifloat or equivalentfixed to wooden/PVC plugs with screws complete all as specified & directed. |
| 51 | S&F in repairs600 mm x 450 mm bevelled edge mirror of selected quality glass ,mounted on 6 mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated screws and washer complete all as specified & directed. |
| 52 | S&F in repairstoilet paper holder with flat recessed type stainless steel material complete all as specified & directed. |
| 53 | S&F in repairsvitreous Chinawash down water closet pan,pedestal patternwhite (excluding flushing cistern) including plastic water closet seat, white closed pattern with flat bottom and cover and mild steel chromium plated hinging device complete all as specified & directed. |
| 54 | S&F in repairs vitreous China squatting pan,‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) including necessary PCC bedding, connected to PVC/CI pipes complete all as specified and directed. |
| 55 | M&L for cleaning and removing of all scale and dirt etc., from tanks, and from mouth of circulating pipes etc. including using 50gm of bleaching powder per tank after disconnecting of outlet pipe and re-connecting in the same position, capacity of tank exc. 250 litres but not exc. 500 litres each and marked on tank with white synthetic enamel paint as \" tank cleaned on ________\" using stencil complete all as specified and directed by Engineer-in-Charge. |
| 56 | M&L for cleaning and removing of all scale and dirt etc., from tanks, and from mouth of circulating pipes etc. including using 70gm of bleaching powder per tank after disconnecting of outlet pipe and re-connecting in the same position, capacity of tank exc. 500 litres but not exc. 1000 litres each and marked on tank with white synthetic enamel paint as \" tank cleaned on ________\" using stencil complete all as specified and directed by Engineer-in-Charge. |
| 57 | S&F in repairs PVC water storage cover of 500/1000 liter capacity of any description and shape as per existing water storage tank including necessary locking facility complete all as specified and directed |
| 58 | S&F in repairsvitreous China half stall urinal of size 350X340X615mm, bowl type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in white cement; fixing to flushing cistern, flush pipe, 40mm bore dia CP finish cast copper alloy waste fitting, CP finish urinal spreader complete all as specified and directed. |
| 59 | S&F in repairs 32/40mm dia PVC flexible waste pipe for wash hand basin, kitchen sink, urinal or similar work complete all as specified and directed. |
| 60 | S&F in repairs 32mm dia CP finish cast copper alloy waste fitting for wash hand basin, with long screwed shanks and fly nut and flange end, bedded in red lead cement complete all as specified and directed. |
| 61 | S&F in repairs CP finish cast copper alloy waste fitting of outlet 32mm dia for stainless steel kitchen sink, as per existing size and designs, with long screwed shanks and fly nut and flange end, bedded in red lead cement complete all as specified and directed. |
| 62 | M&L for pre-cast cement concrete block, (1:3:6), type C1 (using 20mm nominal size, crushed and graded stone aggregate) masonry with solid blocks and setting in cement mortar (1:6) having minimum compressive strength of 50 Kg per Sqcm including dismantling of existing masonary work complete all as specified & directed. |
| 63 | M&L for plain cement concrete, 25mm thick, (1:2:4), type B-0, (using 12.5mm nominal size crushed andgraded stone aggregate) for levelling/to receive screed for laying floor finish, finished fair and even complete all as specified & directed. |
| 64 | M&L for plain cement concrete, 75mm thick, (1:2:4), type B-1, (using 20mm nominal size crushed andgraded stone aggregate)for sub-base of floors & in pavings or of similar work finished fair and even complete all as specified & directed. |
| 65 | M&L for plain cement concrete, 75mm thick, (1:3:6), type C-1, (using 20mm nominal size crushed and graded stone aggregate)for plinth protection including filling of expansion joint with bituminous mixture finished fair and even complete all as specified & directed. |
| 66 | M&L for plain cement concrete, 75mm thick, (1:4:8), type D-1, (using 20mm nominal size crushed andgraded stone aggregate)for sub-base of floors or of similar type of work finished fair and even complete all as specified & directed. |
| 67 | M&L for plain cement concrete type B-1, 1:2:4 (using 20mm nominal size crushed and graded stone aggregate) as in coping, hold fast or of similar type of workincluding necessary form work complete in all respectas specified & directed. |
| 68 | M&L for60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified & directed. |
| 69 | M&Lfor coloured non-skid ceramic tiles 6mm to 7mm thick (square/rectangular) area of each tiles exceeding 0.18 sqm but not exc 0.38 sqm as in floor, set and jointed in neat cement slury and pointed in white cement with pigment to match the shade of tiles including cement screed bed or bedding layer of 15mm thick in cement mortar 1:4 complete all as specified & directed. |
| 70 | M&Lfor coloured glazed ceramic tiles joint less/edge cutted of sizearea of each tiles exceeding 0.18 sqm but not exc 0.38 sqm, 6mm to 7mm thick as in vertical surfaces, set and jointed in neat cement slurry and pointed in white cement with pigment to match the shade of tiles over and including 10mm thick backing/rendering in cement mortar (1:4) complete all as specified & directed. Note:- Those tiles fixed right angled to each other, the each tile should be chamfered/trim/sharp at 45 degrees at joint/corner/edge, the quoted rates are inclusive of this. |
| 71 | M&Lfor glazed/matt finish dark shade Vitrified tiles 7mm to 9mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36 Sqm in floorsset and jointed in neat cement slurry and pointed in white or coloured cement to matchthe tile colour, set and jointed in neat cement slury over cement screed bed or bedding layer15mm thick (1:4) complete all as specified & directed. |
| 72 | M&Lfor glazed/matt finish dark shade Vitrified tiles 7mm to 9mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36 in vertical surfaces etc. set and jointed in neat cement slurry and pointed in white or coloured cement to matchthe tile colour, over and incl 10mm thick plastering in cement mortar 1:4 complete all as specified & directed. Note:- Those tiles fixed right angled to each other the each tile should be chamfered/trim at 45 degrees at joint/corner /edge, the quoted rates are inclusive of this. |
| 73 | M&Lfor 15mm thick cement plaster in CM 1:6 over walls surface of any description and material, finished even & smooth without using extra cement complete all as specified & directed. |
| 74 | M&Lfor 15mm thick cement plaster in CM 1:4 over walls surface of any description and material, finished even & smooth without using extra cement complete all as specified & directed. |
| 75 | M&Lfor 10mm thick cement plaster in CM 1:3 over ceiling surface of any description and material, finished even & smooth without using extra cement complete all as specified & directed. |
| 76 | M&Lfor applying one coat of oil bound distemperon old decorated ceiling surfaces includingpreparation of surfaces and necessary filling of voids with wall care putty complete all as specified & directed. |
| 77 | S&F in repairs 25mm nominal boreCPVC, globe or gate valves, connected with pipe with solventof any material complete all as specified & directed. |
| 78 | S&F in repairs75mm borePVC (SWR) pipes single socketed in any length with rubber ring joints, fixed to wall with necessary mild steel clamps complete all as specified & directed. |
| 79 | S&F in repairs75mm borePVC (SWR) pipes single socketed in any length with rubber ring joints, laid in trenches or in floor complete all as specified & directed. |
| 80 | S&F in repairs110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, fixed to wall with necessary clamps complete all as specified & directed. |
| 81 | S&F in repairs110mmPVC (SWR) pipes single socketed in any length with rubber ring joints, laid in trenches or in floor complete all as specified & directed. |
| 82 | S&F in repairsPVC (SWR) floor trap of outlet dia 75mm, plain with SS gratings 125X125mm size with openable circular grating with or without hole including jointing with solvent cement including fixing to pipe properly with solvent complete all as specified & directed. |
| 83 | S&F in repairsPVC (SWR) bends with access door for 75 mm bore pipe complete all as specified & directed. |
| 84 | S&F in repairsPVC (SWR) bends with access doorfor 110 mm bore pipe complete all as specified & directed. |
| 85 | S&F in repairsPVC (SWR) junction single, (Single T) equal or unequal size with access door for 75 mm bore pipe complete all as specified & directed. |
| 86 | S&F in repairsPVC (SWR) junction single, (Single T) equal or unequal with access door for 110mm bore pipe complete all as specified & directed. |
| 87 | S&F in repairsPVC (SWR) vent cowl 110 mm dia complete all as specified & directed. |
| 88 | S&F in repairsPVC (SWR) vent cowl 75 mm dia complete all as specified & directed. |
| 89 | Supplying, hoisting and fixing of triple layer, ISI marked, 1000 Litre rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) fixed in position all as specified in SSR Part I including PTMT 25mm bore ball valve high pressure with epoxy coated aluminium rod and high density plastic ball , two nos new tank nipples of PTMT material 20/25mm bore dia as required including dismantling of existing water storage tank of any capacity complete all as specified & directed. |
| 90 | S&FAluminium sliding windows shutters powder coated (minimum thickness of powder coating 50 micron)including powder coated main frame,three track (two for glazed and one for wire mesh) without sash barsincluding necessary jointing cleats, glazing clips, EPDM rubber packing, powder coated aluminium snap beading, screws, wheels, locking arrangments, suitable handles for sliding purpose, 4mm thick dark black tint plain glass and stainless steel wire mesh of dia 0.36mm and 1.40mm width of aperature, silicon chemical filling at gaps between section frame and wall surfaces completeallas specified and directed. |
| 91 | S&F in repairssheet glass, ordinary quality, in squares, pane of 4mm thickness not exc 0.5 Sqm each complete all as specified and directed. |
| 92 | S&F in repairsfor factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm² , modules of elasticity 900 N/mm²and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made all as specified and directed. |
| 93 | S&F in repairsstainless steel handles 100mm size, D type dotted for kitchen/cup board cabinet shutters complete all as specified and directed. |
| 94 | S&F in repairsto drawer ball bearing runners 45mm telescopic channel (20 inch) full extension load capacity 50 Kgs complete all as specified and directed. |
| 95 | S&F in repairsMS 300mm, ordinary rat tail rod pattern springs including roller and roller plate of soft closing hydraulic pattern including welding to frame as required complete all as specified & directed. |
| 96 | M&Lfor preparation of old decorated painted wood and wood based surfaces of any description, not otherwise described, over 10cm width or girth and applying one coat of synthetic enamel paint duly filled the voids with enamel based putty complete all as specified & directed. |
| 97 | M&Lfor preparation of old steel surfaces of any description, over 10cm in width or girth, not otherwise described and applying one coat of synthetic enamel paint duly filled the voids with enamel based putty complete all as specified & directed. |
| 98 | S&F in repairs s 25mm dia decorative type stainless steel curtain rods including fixing end brackets, middle brackets , stops, etc. complete all as specified & directed. |
| 99 | S&F in repairs ed window guard bars, hold fasts of plain/square conforming to Fe-290, Gde E-165 and fixed in walls of any description including bed blocks cutting, angle iron/flat iron frame of appd design and similar articles complete all as specified & directed. |
| 100 | M&Lfor applying two coats synthetic enamel paint over new steel surfaces of any description, over 10cm in width or girth, not otherwise described duly filled the voids with enamel based putty complete all as specified & directed. |
| 101 | M&Lfor applying two coats of oil bound distemper over a coat of primer on walls, pillasters, cornices, etc., on newly plastered surfaces using spunge roller including one coat of primer over 2mm thick wall care putty in two coats complete all as specified & directed. |
| 102 | M&Lfor applying two coats of white washon newly plasterd ceiling surfaces including necessary filling of voids with wall care putty complete all as specified & directed. |
| 103 | M&Lfor applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified & directed. |
| 104 | M&L for preparing, washing, rubbing down and stopping of old distempered surface and applying one coat of oil bound distemperusing spunge roller on walls, pillasters, cornices etc, all as specified & directed. |
| 105 | M&L forpreparing, washing, rubbing down and complete removal of existing treatmentfor applying twocoats ofacrylic emulsion paintof Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives over and including priming coat of exterior primer applied on old decorated surfacesofwalls including necessary filling of voids with wall care putty complete all as specified & directed. |
| 106 | S&F in repairs GI wire netting 0.90mm dia and 12mm square mesh lathing to wood or metal studding, joists, etc. in walls, ceilings, stanchions, beams, etc. including all laps, cutting, waste and cutting in plaster, concrete/stone surafce in patches complete all as specified & directed. |
| 107 | S&F 50mm bore dia high density polyethylene pipes (HDPE) and fittings of pressure rating 6kgf/cm² fixed complete to walls, ceilings or in floors as drain out pipe etc., including necessary cutting and chasing in wall or floor of any description complete all as specified & directed. |
| 108 | S&F in repairs 16mm to 18mm thick pre-polished (table rubbed and polished) machine cut Granite stone work (of any type & size)in steps(treads), window/door-cills, cooking platforms, wash hand basin counter and like bedded and jointed with grey cement slurry with 20mm thick cement mortar (1:4) including pointing in white cement with pigment to match with shade of granite and cutting for circular holes of any dia for fixing sanitary fittings or of simialr work including dismantaling of existing stone slab flooring including cement mortar complete all as specified & directed. |
| 109 | S&F in repairs 16mm to 18mm thick pre-polished (table rubbed and polished) machine cut Granite stone work (of any type & size)in steps(risers), jambs, pillars, dado/skirting and like laid over cement screed bedded with 15mm thick cement mortar (1:4) and jointed with grey cement slurryincluding pointing in white cement with pigment to match with shade of granite and cutting for circular holes of any dia for fixing sanitary fittings or of simialr work including dismantaling of existing stone slab flooring including cement mortar complete all as specified & directed. |
| 110 | S&F in repairs20mm diaBall valves high pressure of PTMT with epoxy coated Aluminiumrod& high density plastic ball screwed for iron/CPVC/PPR pipe and fixed complete all as specified & directed. |
| 111 | S&F in repairs25mm diaBall valves high pressure of PTMT with epoxy coated Aluminiumrod& high density plastic ball screwed for iron/CPVC/PPR pipe and fixed complete all as specified & directed. |
| 112 | M&Lfor full round and polished moulding (as per main stone polish) to edges of stone slabs upto 20mm thick, such as in window cill, jambs, counters, steps etc. and of other similar situations complete all as specified & directed. |
| 113 | S&F in repairsfancy swan neck Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered \"Hot\" or \"Cold\" with long screwed shanks and fly-nuts, screwed for iron pipe complete all as specified & directed. |
| 114 | Supplying, hoisting and fixing of double layer, ISI marked, 500 Litre Rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) fixed in position all as specified in SSR Part -I including two nos PTMT/UPVC tank nipple and25mm bore PTMTball valve high pressure with epoxy coated aluminium rod and high density plastic ball including dismantling of existing water storage tank of any capacity complete all as specified & directed. |
| 115 | S&Fin repairs Health faucet (ABS Body) chromium plated suitable for 15 mm borepipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete as specified and directed. |
| 116 | S&Ffactory made uPVC colour Sliding window Three track,area of each window not exceeded 2 Sqm,made of extruded profiles with wall thickness of 2.3mm (+ 0.2mm). Window profile with hollow section with multi chamber. Frame (90mm x 42.5mm), sliding sash (54mm x 32mm). Sliding mesh Sash (54mm x 32mm) Sliding interlock (One vertical length in each shutters) (30mm x 35.50mm), Glazing bead (22mm x 14.5mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2 +0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (18mm x 10mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of Zinc alloyed (white powder coated), steel roller system. The rates includes fiber mesh and 4mm thick frosted toughned glass.. Note: The unit rate quoted by contractor includes all other connected accessories. Net Opening will be measured for payment purpose. |
