|
| 1 | Excavating over areas, not exceeding 1.50 m deep and getting out in soft/loose soil complete all as specifiedand as directed |
| 2 | Screening of sand and saw dust obtained from Srl item No.1aboveby manually or machine byheavy type / big size seive and stacking the serviceable materials for re-use complete all as specifiedand as directed. |
| 3 | Removing of excavated material exc 250 mbut not exceeding 500 m and depositing where directed at a level not exc 1.5 m above the starting point complete all as specifiedand as directed. |
| 4 | Labour only for forming embankments with specified materialspread in layers not exc. 30cm thick and finishing to required slope, size and shape etc, not exc 1.50m high from base complete all as specifiedand as directed. Note:- Serviceable materials obained from Srl item No.2 shall be re-used in this item |
| 5 | Labour only for forming embankments with sand and saw dust spread in layers n.exc. 30cm thick, and finishing to required slope, size and shape etc, exc 1.50 m but not exc 3.00 m high complete all as specifiedand as directed. Note:- Serviceable materials obained from Srl item No.2 shall be re-used in this item |
| 6 | Labour only for forming embankments with sand and saw dust spread in layers n.exc. 30cm thick, and finishing to required slope, size and shape etc, exc 3.0 m but not exc 4.5 m high complete all as specifiedand as directed. Note:- Serviceable materials obained from Srl item No.2 shall be re-used in this item |
| 7 | M&L forsand and saw dust mixed in proportion 1:1 for forming embankmentsspread in layers not exc. 30cm thick, from bottom trench to top butt wall of firing range including watering ,ramming, levelled and finishing to required slope, size and shapecomplete all as specifiedand as directed. |
| 8 | Surface dressing of not exc 15 cm deep of soft/loose soil including levlling of ground complete all as specifed and directed |
| 9 | S&F framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary,gusset plates, riveting, etc.. not exc 10 kg each brackets, confirming to Fe.290.Gde E-165 grade complete all as specifiedand as directed |
| 10 | M&L for cutting holes in stone masonry wall built in cement mortar for inserting hold fasts exc half brick but not exc full brick wall from the face of jambs and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4, type B1 (using 20mm graded crushed stone aggregates) complete all as specifed and directed |
| 11 | Demolition of cement concrete (unreinforced) of any description in any position complete all as specifed and directed |
| 12 | M&L forPCC 1:2:4,type B-1 (using 20mm graded crushed stone aggregates) as in foundation and filling in mass concrete complete all as specified and directed. |
| 13 | M&L for pre-cast cement concrete block masonry with solid blocks of mix 1:3:6(using 20mm graded crushed stone aggregates), exceeding 10 cm in width and setting in mortar 1:6 complete all as specifed and directed |
| 14 | M&L for PCC 1:2:4, type B-1 (using 20mm graded crushed stone aggregates) as in coping including weathering, slightly rounded or chamfered angles and necessary use and waste of form work complete all as specifed and directed |
| 15 | Taking down cement plaster on brick / concrete /stone masonry walls etc including racking out joints, hacking for key, scrubbing down with water etc complete including removing rubbish off the premises complete all as specifed and directed. |
| 16 | M&L for rendering 20mm thick on fair faces of brick work or concrete/stone wall surfaces in CM 1:4 to be finished even and smooth without using extra cement complete all as specifed and directed |
