|
| 1 | Dismantling structural steel work including doors, gates, window, but excluding framed truss etc. |
| 2 | Erection and fixing only rolled sections as in framing for cladding, glazing and the like fixed with angle cleats and connecting plates, etc. |
| 3 | Demolition of Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level), Cement concrete (unreinforced) |
| 4 | Rough excavation not exceeding 1.5 m deep and getting out Soft/loose soil |
| 5 | M&L for hard core of gauge n. exc. 63 mm deposited, spread and levelled in layers n. exc. 15cm thick with broken bricks, watered and rammed to a true surface. |
| 6 | M&L for cement concrete in foundation filling and mass concrete E2, 1:5:10, 40mm graded aggregate. |
| 7 | Dismantling of Bricks (laid flat or on edge) or brick tiles in floors, channels, kerbs, aprons, etc. (each layer), laid dry, or laid, dry and, pointed |
| 8 | Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand (High Gloss and design as per directions of Engineer - in - Charge) |
| 9 | Dismentaling of brick work or stone/ boulder masonary, built in cement mortar including all quoins, arches, pillers etc, but excluding ashler facings, dressed stone work and precast concrete articles. |
| 10 | Labour charges for removing mortar from and cleaning bricks, stacking for measurement including all extra handling and removal and disposing off rubbish of cement mortar |
| 11 | M&L brick work with sub class-B brick straight or curve on plain exc 6m mean radious built in 1:4 cement mortar. (except brick) |
| 12 | M&L Brick work with sub class ‘B’ bricks, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6. |
| 13 | M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips. |
| 14 | M&L for slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like (Type B0, 1:2:4 20mm graded aggregate). |
| 15 | Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter flat rough surface. |
| 16 | M&L for applying neat cement slurry &rendering 15mm thick on fair faces of brick work or concrete surfaces 1:6 cement plaster in wall. |
| 17 | M&L for Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite 20mm thick, Shade as approved by EIC at the time of execution. |
| 18 | M&L Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings framework of water tanks and similar work conforming to Fe.290.Gde-E-165. |
| 19 | S&F for framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete (Fe 410 -W (Gde- E- 250) quality- A) |
| 20 | S&F for anodised Aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified. |
| 21 | Providing fabricating and installation of Aluminium Composite Panel (ACP cladding in pan shape in metallic colour of approved shades, made out of 4 mm thick aluminium composite panel consisting of 3mm thick FR grade mineral core sandwiched between two aluminium sheets (each 0.5mm thick). The aluminium panel cladding sheet shall be coil coated. The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face #1 and polymer (services) coating on face#2 as specified using stainless steelscrews, nuts, bolts, washers, cleats, weather silicon sealant, backer rods etc. as per directions of Engineer - in - Charge) ( cost of aluminium snap snap beading shall be paid separately), (Make Alexia Panels/ Aludecor/ Alstone/ Viva/ Reynobond India). |
| 22 | Providing and fixing double scaffolding system (cup lock type) on the exterior side, up to seven story height made with 40 mm dia M.S. tube 1.5 m centre to centre, horizontal & vertical tubes joining with cup & lock system with M.S. tubes, M.S. tube challies, M.S. clamps and M.S. staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for the required duration as approved and removing it there after. The scaffolding system shall be stiffened with bracings, runners, connection with the building etc wherever required for inspection of work at required locations with essential safety features for the workmen etc. complete as per directions and approval of Engineer-in-charge. The elevational area of the scaffolding shall be measured for payment purpose. The payment will be made once irrespective of duration of scaffolding. |
| 23 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises. |
| 24 | M&L for Virified Ceramic tiles dark shade/double charged/ ultracharged, 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match (Make - Nitco/ Kazaria/ Johnson/ Somany) |
| 25 | M&L for Screed bed or bedding layer of mortar 15 mm thick for laying floor finishes 1:6 |
| 26 | M&L for interior cementitious tile adhesive for vitrified tiles including grinding with power grinder on existing surface (colour white) (MYK/ Sika/ Pidilite/Somany). |
| 27 | Dismantling boarding, any description, fixed in any position with nails |
| 28 | M&L for Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre tocentre/ intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre. |
| 29 | M&L for 8mm thick seamless calcium silicate ceiling made out of 1800 x 1200 mm size board of siliceous and calcareous material reinforced with cellulose fibre fixed to the ceiling section with 25 mm long self drilling and tapping screws having phillips head with under head cutter at 200 mm centre to centre, including finshing the joint of face board with specially formulated jointing compound and 48 mm wide fibre tape to provide seam less finish (Frame work for ceiling shall be measured and paid separately)(Make-Hilux or equivalent). |
| 30 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. (JK/ Birla) |
| 31 | M&L, apply primer paint and exterior grade plastic emulsion paint two coats on surfaces of any description over 10cm girth or width, not otherwise described (Make - Apex of Asian paints) / weathercoat of Berger paints/ Suraksha of Nerolac paints) Shade as approved by EIC at the time of execution. |
| 32 | M&L for cutting chases, pinning in making good to facings where required and pointing in cement morter 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc, and cutting chases forconcealed water tubing & conceal conduit wiring etc. and making good, cutting not exc 10 cm girth in brick walls. |
| 33 | M&L for fixing stain less steel letters or figures (Block, Roman, Italic or Indian) n exc. 20 cm high, thickness 25mm. |
| 34 | M&L for fixing stain less steel letters or figures (Block, Roman, Italic or Indian) n exc. 15 cm high, thickness 25mm |
| 35 | M&L forpreparing old steel surfaces, apply synthetic enamel(ordinary/ tint) painting two coat Surfaces of anydescription, not otherwise descri-bed, over 10cm width or girth steel based surface (Asian paints / Nerolac/ Berger). approved by OFCd. |
| 36 | Removing the excaveted debris exc. 1.5km butn exc 5km and depositing where directed. |
| 37 | Supply and fixing factory made uPVC white colour Two track four panels sliding glazed door made of (big series) frame 67 x 50 mm & sash 46 x 82 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead/ double glazing bead of appropriate dimension. (Area of door above 8.00 sqm upto 10.00 sqm) comprising of uPVC multi-chambered frame, with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension uPVC extruded glazing beads, uPVC extruded interlock and uPVC extruded Inline sash adaptor (if required), EPDM gasket, wool pile, zinc alloy (white powder coated) handle with key on one side of extreme panels along with zinc plated mild steel multi point locking having transmission gear with keeps, zinc alloy (white powder coated) cresent lock (if required), stainless steel (SS 304 grade) body with adjustable double nylon rollers (weight bearing capacity to be 120 kg), G.l fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware\"s and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. (Make- Prominance/ AIS/ Duroplast/ LG Hausys/ Saint Gobain/ Simta/ Fenesta). |
| 38 | Supply and fixing factory made uPVC white colour Casement door with top hung ventilator with 3D and SS friction (400 x 19 x 1.9 mm) made of (big series) frame 67 x 64 mm, sash 67 x 110 mm & mullion 67 x 80 mm all having wall thickness of 2.3 + 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of door upto 2.50 sqm) comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, zinc alloy (white powder coated) 3D hinges and one handle on each side of panels along with zinc plated mild steel multi point locking having transmission gear, cylinder with keeps and one side key, G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws, etc.Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware\"s and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality complete all as specified and directed by Engineer-in-Charge (Make- Prominance/ AIS/ Duroplast/ LG Hausys/ Saint Gobain/ Simta/ Fenesta). |
| 39 | M&L for 4.8mm thick sheet glass , ordinary quality and glazing with oil putty in square exc 0.5sq.mtr in each pane sheet glass is ground or obscured or frosted, on one side.(Make Saint Gobain/ Modi guard, ISI mark) |
| 40 | S&F for door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed (Aluminium (extruded section) body. |
| 41 | M&L for concealled type wiring for one light point or one fan point or 5A plug point controlled by one switch with 1.5sqmm size copper cables in PVC conduit (Make Finolex/ Havells/ Anchor) (Incl.JB/ concelled boxes etc.). |
| 42 | M&L for 5A switch piano flush button single pole one way (Make Anchor/ Cub/ Arkay/ Cona) |
| 43 | Supply and fixing round shape 15 watt 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete (Make- CG/ Phillips / Havells/ Panasonic/ Wipro). |
