|
| 1 | Earth work in excavation by mechanicalmeans (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. |
| 2 | All kinds of soil. |
| 3 | Providingandlayinginpositioncementconcreteof specified grade excluding the cost of centering and shuttering - All work up to plinth level : |
| 4 | 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 5 | Extra for providing 151 marked Stainless Steel butt hinges instead of M.S. pressedbutthingesbright finishedof requiredsize with necessary screws. (Shutter area to be measured). |
| 6 | Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : |
| 7 | 150x10 mm |
| 8 | Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : |
| 9 | 125 mm |
| 10 | Providing and fixing factory made uPVC door frame made of uPVC extruded sections having an overall dimension as below (tolerance ±1mm),with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame to be Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19 mm and 1mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturer’s specification and direction of Engineer-in-charge |
| 11 | Extruded section profile size 48x40 mm |
| 12 | Providing and fixing factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5 mm thick heat moulded PVC \"C\" channel of size 30 mm thickness, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5 mm thick, 95 mm wide PVC sheet out of which 75mm shall be flat and 20 mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided both side of the panel. 10 mm (5 mm x 2 ) thick, 20 mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail, paneling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles & rails with 7 mm (5 mm+2 mm) thick x 15 mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5 mm thick PVC strip of 20 mm width is to be stuck on the interior side of the \"C\" Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge, manufacturer\"s specification & drawing. |
| 13 | 30 mm thick plain PVC door shutters |
| 14 | Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. |
| 15 | 40 mm thick with 20 mm nominal size stone aggregate |
| 16 | Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. |
| 17 | 0.30 mm thick with zinc coating not less than 275 gm/ m² |
| 18 | Providing and fixing white vitreous china pedestal type water closet(European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : |
| 19 | W.C. pan with ISI marked white solid plastic seat and lid |
| 20 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall |
| 21 | 20 mm nominal dia Pipes |
| 22 | 40 mm nominal dia Pipes |
| 23 | Providing and fixingtwo way bid cock with wall flange of approved quality QQT-7041 or equivalent of approved quality as per the direction of Engineer-in-charge [Jaquar Make] |
| 24 | Providing and fixing C.P. Hand Shower [Health faucet] [ABS Body] with 1.20 Mtr long PVC Tube and Wall hock make [Jaquar ALD-BLK 583 or equivalent. |
| 25 | Providing and fixing Angular stop cockof approved makeJaguar / perryware , FLR-CHR-5053Nor equivalent |
| 26 | 15mm nominal bore |
| 27 | Providing and fixing 19mm thick Marine Ply wood of IS 710 Grade on E-W/C Room Floor including requiired nails etc all complete as per direction of Engineer-in-charge |
| 28 | Providing and fixing soil, waste and vent pipes with UPVC pipe conforming to IS :13592 type B including joining with seal ring conforming to IS: 5382 living 10mm gap for thermal expansion(i) single socketed pipes |
| 29 | 110 mm dia PVC(Pipe 6 kg/per sqcm) |
| 30 | 75 mm dia PVC(Pipe 6 kg/per sqcm) |
| 31 | Providing and fixing ball valve CPVC of approved quality, high or low pressure with plastic floats completeigh or low pressure, with plastic floats complete : |
| 32 | 20mm nominal bore |
| 33 | 40mm nominal bore |
| 34 | Providing wood work frame in trusses, purlins, in post, truss, purlins, rafter, wall partition, strucutre with sawn timber i/c required screws, nails etc all completeSuperior class hard wood cat-II \"A\" |
