Housing Urban and Rular Development Government Departments Closing in 0 days TDR #54252673

Tender For Development Of Igc Changsari Dist.- Kamrup

Issued by Government Departments · Kamrup, Assam
Tender Value
Ref. Documents
Estimated cost
Bid Submission
09 Mar 2026
0 days left
EMD
9.70 Lakhs
Bank guarantee accepted
Document Fee
10000
Non-refundable
Tender Type
Online

Tender Overview

Competition Type
NCB
Bidding Type
Tender
Location / State
Kamrup → Assam
EMD Exemption
Available
Quantity
Not Available

Project Description

Tender For Development Of Igc Changsari Dist.- Kamrup- 1 APPORACH AND INTERNAL ROAD- Construction of Subgrade and Earthen Shoulders(Construction of subgrade and earthen shoulders with approved materials obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of table (300-2) (a), (Including cost of testing of materials at site and laboratory as directed by the deptt.) 2 Granular Sub-Base with well graded material(Table 400-1)(B) By Mix in Place MethodConstruction of Granular Sub-base by providing close graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator with OMC and compacting with vibratory roller to achieve the desired density, complete as per Technical Specification Clause 401(Including cost of testing of materials at site and laboratory as directed by the deptt.)(i) For Grading I Material 3 Water Bound Macadam (Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with vibratory roller 8-10 tonnes in stages to proper grade and camber, applying and brooming requisite type of screening/binding material to fill up the interstices of coarse aggregate, watering and compacting to the required density(with an initial lead of 5.0 km ) A) By Manual Means (I) For grading –II (b) Using Screening Type-A (13.2mm Agg.) 4 (II) For grading –III (c) Using Screening Type-B (11.2mm Agg.) 5 Providing and laying interlocking concrete block pavement (ICBP) conforming to IS: 15658-2006 including all lead and lift complete as per technical specification and directed.(a) 100 mm thick interlocking precast blocks having compressive strength 50 N/ sq.m 6 Providing and laying M-40 grade cement concrete edge block/ edge restraints complete asper technical specification clause 1504. 7 RCC DRAIN- Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth, 1.5m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth, lead up to 50m and lift up to 1.5m,as directed by Engineer-in-Charge. All kinds of soil. 8 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6 (1 Cement : 3 coarse sand(zone-III) : 6 graded stone aggregate 20 mm nominal size). 9 Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size) 10 Centering and shuttering including strutting, propping etc. and removal of form for : Foundations, footings, bases of columns, etc. for mass concrete 11 Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc. 12 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more. 13 Dry brick pitching half brick thick in drains including supply of bricks and preparing the surface complete : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 14 CULVERT- Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth. 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed. 15 Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete. 16 Providing and laying in positon cement concrete of specified grade excluding the cost of centering and shutttering - All work up to plinth level: a) In Prop. 1 cement : 3 Sand : 6 Coarse agg. by volume 17 Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering , shuttering, finishing and reinforcement - All works up to plinth level: 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size) 18 Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundations and plinth in : cement mortar 1:4 (1 cement : 4 coarse sand) 19 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand) 20 Centering and shuttering including strutting, propping etc, and removal of form for: Foundations, footings, bases of columns etc. for mass concrete 21 12 mm Cement plaster of mix 1:6 ( 1 cement : 6 fine sand) 22 15 mm Cement plaster on the rough side of single or half brick wall mix 1:6 ( 1 cement : 6 fine sand) 23 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more. 24 CONSTRUCTION OF 11 KV & 3 PHASE LT LINE- GI Steel Tubular Pole, SP-66 25 11KV Danger Plate 26 11 KV T Cross Arm (GI) with angle size 50x50x6mm 27 Galvanized Channel Cross Arm (100x50x6x2200) mm 28 Composite Polymeric 11 kV Pin Insulator (5 KN) FRP 24mm 29 Composite Polymeric 11 kV Disc Insulator (70 KN) with H/W Fitting(T&C) 30 ACSR Raccon Conductor 31 Al Bimatellic Wire 32 Tension Clamp for Raccon ACSR 33 3Cx120 + 1Cx95sqmm (Meassenger cum neutral) 34 Cable tie 35 Anchor Clamp Wedge Type LT ABC as per NFC Standard 36 Suspension Clamp 37 Eye Hook for anchor & suspension Clamp 38 Pole Clamp of GI Flat 50x6mm 39 Cable End Caps for AB Cables 40 ASA Disbribution box with pre-fitted lug for 250A 3 Ph 10 connectors with spring loaded Busbar system for service connection. 41 Steel strap for installing DB size 20mm x 1m long 42 Buckle for steel strap for DB fixing 43 10 Sq.mm AL PVC Cable per Distribution Box 44 Insulating piercing connector IPC P2x95 for DB charging as per NFC 45 Insulating piercing connector IPC P2x95 for ABC to ABC TEE connection as per NFC Std. 46 Insulated crimping type midspan joint (set contains 5 nos. ferrules as per cable) as per NFC std. 47 GI Earth Pipe, 50mm dia, 3 Mtr. Length 48 GI Wire 8 SWG for earthing 49 HT Stay Set 50 GI Stay Wire, 7/10 SWG 51 GI Nuts & Bolts with Washers (assorted) 52 LT Danger Plate 53 11KV Danger Plate 54 Transportation & Storage Charges Rs. 86606.39 55 Grouting & Mufflering of Steel Tubular Pole SP-22 56 Grouting of Stay Set with PCC and Boulder 57 Supervision Charge amount payable to APDCL Rs. 59567.58 58 Solart Street Lights- SEMI-Integrated (Two in One) / Integrated LED SolarStreet Light: LED Luminary rating 30 Watt,100 Wp 12 Volt Solar Panel, LiFePO4 Lithium FerroPhosphate Battery with 30 Ah Capacity, 12 Volt, 2000 Charge/Discharge Cycle,PWM with Auto Dusk-to-Dawn ON/OFF, Die Cast Aluminium enclosure with IP 66 rating along with 20 ft GI Tubular Pole (76mm round) and galvanised mounting accesories including 3 years comprehensive onsite warranty ((Make- LUMINOUS, Waaree, Phylips, Crompton, Bajaj or Equivalent) Please Enable Macros to View BoQ information

BOQ

Name of Work:- Development Of Igc Changsari Dist.- Kamrup
Sl. No. Item Description
1APPORACH AND INTERNAL ROAD- Construction of Subgrade and Earthen Shoulders(Construction of subgrade and earthen shoulders with approved materials obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of table (300-2) (a), (Including cost of testing of materials at site and laboratory as directed by the deptt.)
2Granular Sub-Base with well graded material(Table 400-1)(B) By Mix in Place MethodConstruction of Granular Sub-base by providing close graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator with OMC and compacting with vibratory roller to achieve the desired density, complete as per Technical Specification Clause 401(Including cost of testing of materials at site and laboratory as directed by the deptt.)(i) For Grading I Material
3Water Bound Macadam (Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with vibratory roller 8-10 tonnes in stages to proper grade and camber, applying and brooming requisite type of screening/binding material to fill up the interstices of coarse aggregate, watering and compacting to the required density(with an initial lead of 5.0 km ) A) By Manual Means (I) For grading –II (b) Using Screening Type-A (13.2mm Agg.)
4(II) For grading –III (c) Using Screening Type-B (11.2mm Agg.)
5Providing and laying interlocking concrete block pavement (ICBP) conforming to IS: 15658-2006 including all lead and lift complete as per technical specification and directed.(a) 100 mm thick interlocking precast blocks having compressive strength 50 N/ sq.m
6Providing and laying M-40 grade cement concrete edge block/ edge restraints complete asper technical specification clause 1504.
7RCC DRAIN- Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth, 1.5m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth, lead up to 50m and lift up to 1.5m,as directed by Engineer-in-Charge. All kinds of soil.
8Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6 (1 Cement : 3 coarse sand(zone-III) : 6 graded stone aggregate 20 mm nominal size).
9Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size)
10Centering and shuttering including strutting, propping etc. and removal of form for : Foundations, footings, bases of columns, etc. for mass concrete
11Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.
12Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.
13Dry brick pitching half brick thick in drains including supply of bricks and preparing the surface complete : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
14CULVERT- Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth. 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed.
15Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete.
16Providing and laying in positon cement concrete of specified grade excluding the cost of centering and shutttering - All work up to plinth level: a) In Prop. 1 cement : 3 Sand : 6 Coarse agg. by volume
17Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering , shuttering, finishing and reinforcement - All works up to plinth level: 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size)
18Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundations and plinth in : cement mortar 1:4 (1 cement : 4 coarse sand)
19Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand)
20Centering and shuttering including strutting, propping etc, and removal of form for: Foundations, footings, bases of columns etc. for mass concrete
2112 mm Cement plaster of mix 1:6 ( 1 cement : 6 fine sand)
2215 mm Cement plaster on the rough side of single or half brick wall mix 1:6 ( 1 cement : 6 fine sand)
23Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.
24CONSTRUCTION OF 11 KV & 3 PHASE LT LINE- GI Steel Tubular Pole, SP-66
2511KV Danger Plate
2611 KV \"T\" Cross Arm (GI) with angle size 50x50x6mm
27Galvanized Channel Cross Arm (100x50x6x2200) mm
28Composite Polymeric 11 kV Pin Insulator (5 KN) FRP 24mm
29Composite Polymeric 11 kV Disc Insulator (70 KN) with H/W Fitting(T&C)
30ACSR Raccon Conductor
31Al Bimatellic Wire
32Tension Clamp for Raccon ACSR
333Cx120 + 1Cx95sqmm (Meassenger cum neutral)
34Cable tie
35Anchor Clamp Wedge Type LT ABC as per NFC Standard
36Suspension Clamp
37Eye Hook for anchor & suspension Clamp
38Pole Clamp of GI Flat 50x6mm
39Cable End Caps for AB Cables
40ASA Disbribution box with pre-fitted lug for 250A 3 Ph 10 connectors with spring loaded Busbar system for service connection.
41Steel strap for installing DB size 20mm x 1m long
42Buckle for steel strap for DB fixing
4310 Sq.mm AL PVC Cable per Distribution Box
44Insulating piercing connector IPC P2x95 for DB charging as per NFC
45Insulating piercing connector IPC P2x95 for ABC to ABC TEE connection as per NFC Std.
46Insulated crimping type midspan joint (set contains 5 nos. ferrules as per cable) as per NFC std.
47GI Earth Pipe, 50mm dia, 3 Mtr. Length
48GI Wire 8 SWG for earthing
49HT Stay Set
50GI Stay Wire, 7/10 SWG
51GI Nuts & Bolts with Washers (assorted)
52LT Danger Plate
5311KV Danger Plate
54Transportation & Storage Charges Rs. 86606.39
55Grouting & Mufflering of Steel Tubular Pole SP-22
56Grouting of Stay Set with PCC and Boulder
57Supervision Charge amount payable to APDCL Rs. 59567.58
58Solart Street Lights- SEMI-Integrated (Two in One) / Integrated LED SolarStreet Light: LED Luminary rating 30 Watt,100 Wp 12 Volt Solar Panel, LiFePO4 Lithium FerroPhosphate Battery with 30 Ah Capacity, 12 Volt, 2000 Charge/Discharge Cycle,PWM with Auto Dusk-to-Dawn ON/OFF, Die Cast Aluminium enclosure with IP 66 rating along with 20 ft GI Tubular Pole (76mm round) and galvanised mounting accesories including 3 years comprehensive onsite warranty ((Make- LUMINOUS, Waaree, Phylips, Crompton, Bajaj or Equivalent) Please Enable Macros to View BoQ information

AI Tender Summary

OUR REF NO 54252673
AUTHORITY Government Departments
TENDER VALUE Ref. Documents
LAST DATE 09-03-2026
Authority
Authority Name Assam Industrial Infrastructure Development Copr
Work Description Tender For Development Of Igc Changsari Dist.- Kamrup- 1 APPORACH AND INTERNAL ROAD- Construction of Subgrade and Earthen Shoulders(Construction of subgrade and earthen shoulders with approved materials obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of table (300-2) (a), (Including cost of testing of materials at site and laboratory as directed by the deptt.) 2 Granular Sub-Base with well graded material(Table 400-1)(B) By Mix in Place MethodConstruction of Granular Sub-base by providing close graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator with OMC and compacting with vibratory roller to achieve the desired density, complete as per Technical Specification Clause 401(Including cost of testing of materials at site and laboratory as directed by the deptt.)(i) For Grading I Material 3 Water Bound Macadam (Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with vibratory roller 8-10 tonnes in stages to proper grade and camber, applying and brooming requisite type of screening/binding material to fill up the interstices of coarse aggregate, watering and compacting to the required density(with an initial lead of 5.0 km ) A) By Manual Means (I) For grading –II (b) Using Screening Type-A (13.2mm Agg.) 4 (II) For grading –III (c) Using Screening Type-B (11.2mm Agg.) 5 Providing and laying interlocking concrete block pavement (ICBP) conforming to IS: 15658-2006 including all lead and lift complete as per technical specification and directed.(a) 100 mm thick interlocking precast blocks having compressive strength 50 N/ sq.m 6 Providing and laying M-40 grade cement concrete edge block/ edge restraints complete asper technical specification clause 1504. 7 RCC DRAIN- Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth, 1.5m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth, lead up to 50m and lift up to 1.5m,as directed by Engineer-in-Charge. All kinds of soil. 8 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6 (1 Cement : 3 coarse sand(zone-III) : 6 graded stone aggregate 20 mm nominal size). 9 Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size) 10 Centering and shuttering including strutting, propping etc. and removal of form for : Foundations, footings, bases of columns, etc. for mass concrete 11 Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc. 12 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more. 13 Dry brick pitching half brick thick in drains including supply of bricks and preparing the surface complete : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 14 CULVERT- Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth. 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed. 15 Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete. 16 Providing and laying in positon cement concrete of specified grade excluding the cost of centering and shutttering - All work up to plinth level: a) In Prop. 1 cement : 3 Sand : 6 Coarse agg. by volume 17 Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering , shuttering, finishing and reinforcement - All works up to plinth level: 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size) 18 Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundations and plinth in : cement mortar 1:4 (1 cement : 4 coarse sand) 19 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand) 20 Centering and shuttering including strutting, propping etc, and removal of form for: Foundations, footings, bases of columns etc. for mass concrete 21 12 mm Cement plaster of mix 1:6 ( 1 cement : 6 fine sand) 22 15 mm Cement plaster on the rough side of single or half brick wall mix 1:6 ( 1 cement : 6 fine sand) 23 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more. 24 CONSTRUCTION OF 11 KV & 3 PHASE LT LINE- GI Steel Tubular Pole, SP-66 25 11KV Danger Plate 26 11 KV T Cross Arm (GI) with angle size 50x50x6mm 27 Galvanized Channel Cross Arm (100x50x6x2200) mm 28 Composite Polymeric 11 kV Pin Insulator (5 KN) FRP 24mm 29 Composite Polymeric 11 kV Disc Insulator (70 KN) with H/W Fitting(T&C) 30 ACSR Raccon Conductor 31 Al Bimatellic Wire 32 Tension Clamp for Raccon ACSR 33 3Cx120 + 1Cx95sqmm (Meassenger cum neutral) 34 Cable tie 35 Anchor Clamp Wedge Type LT ABC as per NFC Standard 36 Suspension Clamp 37 Eye Hook for anchor & suspension Clamp 38 Pole Clamp of GI Flat 50x6mm 39 Cable End Caps for AB Cables 40 ASA Disbribution box with pre-fitted lug for 250A 3 Ph 10 connectors with spring loaded Busbar system for service connection. 41 Steel strap for installing DB size 20mm x 1m long 42 Buckle for steel strap for DB fixing 43 10 Sq.mm AL PVC Cable per Distribution Box 44 Insulating piercing connector IPC P2x95 for DB charging as per NFC 45 Insulating piercing connector IPC P2x95 for ABC to ABC TEE connection as per NFC Std. 46 Insulated crimping type midspan joint (set contains 5 nos. ferrules as per cable) as per NFC std. 47 GI Earth Pipe, 50mm dia, 3 Mtr. Length 48 GI Wire 8 SWG for earthing 49 HT Stay Set 50 GI Stay Wire, 7/10 SWG 51 GI Nuts & Bolts with Washers (assorted) 52 LT Danger Plate 53 11KV Danger Plate 54 Transportation & Storage Charges Rs. 86606.39 55 Grouting & Mufflering of Steel Tubular Pole SP-22 56 Grouting of Stay Set with PCC and Boulder 57 Supervision Charge amount payable to APDCL Rs. 59567.58 58 Solart Street Lights- SEMI-Integrated (Two in One) / Integrated LED SolarStreet Light: LED Luminary rating 30 Watt,100 Wp 12 Volt Solar Panel, LiFePO4 Lithium FerroPhosphate Battery with 30 Ah Capacity, 12 Volt, 2000 Charge/Discharge Cycle,PWM with Auto Dusk-to-Dawn ON/OFF, Die Cast Aluminium enclosure with IP 66 rating along with 20 ft GI Tubular Pole (76mm round) and galvanised mounting accesories including 3 years comprehensive onsite warranty ((Make- LUMINOUS, Waaree, Phylips, Crompton, Bajaj or Equivalent) Please Enable Macros to View BoQ information
Basic Detail
Tender No E No. 746034/60 date 22/02/2026
Bidding Type Tender
Location
City Kamrup
State Assam
Key Dates
Publish Date 24 Feb 2026
Submission Date 09 Mar 2026
Open Date 09 Mar 2026
Finance
Tender Value Ref. Documents
Tender Fee 10000
EMD 9.70 Lakhs
Exemption Available
Document List
BOQ_81727.xls
e30067df-1e25-4bab-adbd-ece300d9be8b.html
FOB.pdf
Tendernotice_1.pdf
Tendernotice_2.pdf
Bid_document.pdf

Unlock Full AI Tender Summary

Get instant access to the complete AI-generated analysis — scope, eligibility, timeline & more.

Instant Access Secure Free
Your details are secure and used only for document delivery.

Tender Timeline

Feb 24, 2026
11:30 IST

Tender Published

Tender notice published.

Completed
Mar 09, 2026
17:00 IST

Bid Submission Deadline

Online submission via eProcurement portal.

Completed
Mar 09, 2026

Bid Opening Date

Technical bids will be opened and evaluated.

Completed

Tender Documents

Download All (ZIP) ↓
xls

BOQ_81727.xls

html

e30067df-1e25-4bab-adbd-ece300d9be8b.html

pdf

FOB.pdf

pdf

Tendernotice_1.pdf

pdf

Tendernotice_2.pdf

pdf

Bid_document.pdf

Disclaimer

We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender