|
| 1 | Taking down unserviceable FTL/batten fittings with supply and fix LED batten fitting 20 Watt, 240V, 4ft CDL/NW comprises of extruded channel in thermally conductive material with decorative end cap and high translucent serration milky white diffuser of high optically efficient plastic FR grade. The luminaire is pre-wired with high efficiency electronic driver having operating voltage 140-270V, P.F >0.95, THD <20% and IP20 protected alongwith provision of two Nos of PVC box of size 75x75x20mmor suspension wire of 1.5 mtr is included (02 nos) for hanging with ceiling surfaces by fastener bolt as per site requirement for mounting light fittings and as specified and directed by Engr-in-Charge. |
| 2 | S&F 10WLED batten with inbuilt smart motion sensor, 230 Volt , 50 Hz , 2 feet, polycarbonate extruted channel, powder coated with diffuser for glare free light, Inbuilt motion sensor prewired with 25% dimmer illuminous in ideal timewith all accessories including two Nos of PVC box of size 75x75x20mm for mounting light fittings including ceiling rose complete with following specification.(i) housing-polycarbonate extrusion,diffuser- opal- polymer, LED type- MID power ,Light distribition- general Spread, LED efficiency - > 130 lumen/Watt, System effieciency- > 100 lumen/Watt, Driver efficiency - more than 85%, power factor- more than 0.95, THD - <10%, Mounting/Fixing- Wall/Ceiling, Ingress Protection - IP-20, Sensor type- HF inbuilt integral occupancy/movement sensor, sensor range- upto 5 mtrs(cone formation ), Dimming operation- default operation at 25% of the is rated value. On detection of motion, light output rises to 100% for upto 20 sec . in absence of otion switches back to default operation, LED life- upto 30,000 Hrs.Surge Protection- not less than 1KV. |
| 3 | Taking down old existing unserviceable recessed mounting/hanging light fittings and Supply and fix 1\" x 4\" LED luminaires CRCA housing, white powder coated, with polymer diffuser complete with all accessories suitable for recessed mounting 36 Watt, 240V, CDL/NW. The luminaire is pre-wired with high efficiency electronic driver having operating voltage 140-270V, P.F >0.95, THD <20% and IP20 protected alongwith provision of two Nos of PVC box of size 75x75x20mm for mounting light fittings or suspension wire of 1.5 mtr is included (02 nos) for hanging with ceiling surfaces by fastener bolt as per site requirement and as specified and directed by Engr-in-Charge. |
| 4 | Taking down old unserviceable ceiling fan of any size/Make and deposite to MES store, Supply and fixing of ceiling fan 230V, 50 Hz, AC, 1200mm sweep, min air delivery 210 CFM with service value 6.00 BEE, five star rated with brushless direct current motor (BLDC) complete with hanging arrangement by down rod alongwith steel wire rope for additional safety in ceiling fan with all allied accessories and connecting up with three core, 0.75 sqmm PVC insulated copper conductor cable complete all as sepecified. |
| 5 | Taking down deterioted louvers and supply and fix new louvers, fixed type made out of 1.6 mm GI sheet with horizontal ventilation, bending into shape of size 45cmx45cm(outer) with 20x3mm flat iron base of size 45cmx45cm complete by providing of fixing arrangement for louvers upto 5th floor of including rate all as specified and directed by Engr-in-Charge. |
| 6 | S&F in replacement with new cable PVC insulated three core over all PVC sheathed 2.5 Sqmm stranded copper conductor flexible cable for connecion from DB to connector junction box for power supply to security light fittings drawn in PVC cashing capping or PVC conduit not less than 20mm as required at site and as directed by Engineer-in-Charge including taking out old one. Note - Quoted rate included for PVC cashing cappping / PVC conduit pipe (Medium grade) with fixing accessories like Band, clamp, junction etc. 3 core cable shall be measure as a single unit. |
| 7 | S & F in repair junction box of size not less than 4x4 inch with connector encloser, 3 terminal/ PVC/ polycarbonate, isolated body including taking out old one. |
| 8 | S&F building security light bracket bend to shape made as required of 25/32mm dia, GI pipe light grade fixed to pole/ Wall including M&L for fixing with the help of flat iron clampwith the help of nuts and bolts for fixing of building security light fitting on the wall complete after taking out oldU/S one all as specified and as directed. |
| 9 | Taking out Old, U/s one Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete. Note :- GI bracket shall be measured and paid seperately. |
| 10 | S & F in replacement with Analog Timelite distribution board 16A, 3 pole, 230 Volt with contactor, relay and prewired with Analog time switch 3P Module, 24 hours program, programmable every 15 min., backup of 100 hours, current capacity 16A for ON/OFF controlling of security lights and including taking out old unserviceable complete all as specified and directed |
| 11 | M & L forDLP trunkingsystem of size 80x50mm fixing on wall Completeincluding taking down old DLP system with all accesoriesall as specified and directed. Note : Cover and fittings shall be measured and paid seperately. |
| 12 | M & L forDLPtrunkingsystem of size 105x50mm fixing on wall Complete including taking down old DLP systemwith all accesories all as specified and directed. Note : Cover and fittings shall be measured and paid seperately. |
| 13 | M & L for DLPtrunkingsystem of size 150x50mm fixing on wall Complete including taking down old DLP system with all accesories all as specified and directed. Note : Cover and fittings shall be measured and paid seperately. |
| 14 | M & L for flexible cover of size 65mm for DLP trunking Completeall as specified and directed. |
| 15 | M & L for flexible cover of size 85mm for DLP trunking Completeall as specified and directed. |
| 16 | M & L for flexible cover of size 130mm for DLP trunking Completeall as specified and directed. |
| 17 | M & L for Base joint for DLP trunking Completeall as specified and directed. |
| 18 | M & L forcover joint of size 65mm for DLP trunking Completeall as specified and directed. |
| 19 | M & L forcover joint of size 85mm for DLP trunking Completeall as specified and directed. |
| 20 | M & L forcover joint of size 130mm for DLP trunking Completeall as specified and directed. |
| 21 | M & L for90 degree flat angle for 80x50 mm DLP trunking Completeall as specified and directed. |
| 22 | M & L for90 degree flat angle for 105x50 mm DLP trunking Completeall as specified and directed. |
| 23 | M & L for90 degree flat angle for 150x50 mm DLP trunking Completeall as specified and directed. |
| 24 | M & L forinternal angle adj 80-100 degree for DLP trunking Completeall as specified and directed. |
| 25 | M & L forexternal angle adj 85-120 degree for DLP trunking Completeall as specified and directed. |
| 26 | M & L forclip on partition for DLP trunking Completeall as specified and directed. |
| 27 | M & L forseparation partition for DLP trunking Completeall as specified and directed. |
| 28 | M & L for left or right end for 80x50 mm DLP trunking Completeall as specified and directed. |
| 29 | M & L for left or right end for 105x50 mm DLP trunking Completeall as specified and directed. |
| 30 | M & L for left or right end for 150x50 mm DLP trunking Completeall as specified and directed. |
| 31 | Taking out old existing unarranged submain cables/communications cable/conduits/casing caping from wall surfaces and keep a side and refixing the same after making good of wall surfaces under cable trunking/trays complete all as specified and directed. |
| 32 | M&L for submain wiring with PVC insulated, PVC sheathed, armoured, FRLS 1100 V grade, 3 core 10 sqmm stranded copper conductor fixed on wall roof/duct complete and connecting from TPN DB to SPN DBs with glands including taking out existing damaged cables complete all as specified and directed. |
| 33 | Taking down old existing userviceable recessed mounting light fittings and Supply and fix 2\" x 2\" LED lumination, CRAC housing with efficient optics ensuring perfectly uniform illumination, with polymet diffuser complete with all accessories suitable for recessed mounting 36 Watt, 240V, CDL/NW. The luminaire is pre-wired with high efficiency electronic driver having operating voltage 140-270V, P.F>0.95, THD<20% mounting light fittings as specified and directed by Engr-in-Charge. |
