|
| 1 | Taking down Shutters of any description exc 1 sq. mand n exc 2 sqm each |
| 2 | Taking down Chowkat or frames with shutters(without taking off shutters from the frames)exc 1.5 but n.exc 4.00 sqm each |
| 3 | Taking down and romoving Chowkats or frames not exc. 1.5 sq.m with shutter (without taking off shutters from the frames)complete all as specified. |
| 4 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premise |
| 5 | Demolition of cement concrete (unreinforced) in ground floors and paving n. exc. 15 cm thickness (below or above ground level) complete all as specified. |
| 6 | Taking down cement plaster on brick or stone walls, etc including raking out joints, hacking for key, scrubbing down with water etc.Note the area includs in this up to 4th stories building |
| 7 | S&F powder coating anodised aluminium section for shutter/frame for door, window and ventilator complete all as specified. |
| 8 | S & F powder coated frame sections for doors and windows approved and fixed all as specified and directed. (Note : (i) Paneling such as glass , Gauge etc will be measured and paid saperately.(ii)The rate quoted under this item deemed included for necessary jointing cleates, glazing clips, alluminium beading, screws, rubber packing and locking devices & in built handles for sliding windows. However, no element on account of weight will be taken into consideration for these item.(iii)Floor door spring/locks/tower bolts/ handles/ door closure/hinges for doors measured saparately.(iv) Size of door / windows shall be all as directed at site.(v)Grills will be measured saparately.(vi) Second class hard wood batten of appropriate size to be inserted inside the frame for fixing hinges and the same is included in the rate quoted.) |
| 9 | S & F plain sheet glass 5 mm thick tinted,fixed to aluminium doors/ windows / ventilators complete all as directed by Engr-in-Charge (Note:- Beading/rubber packing is included in the rates for aluminium sections above.) |
| 10 | M&L for Anodised aluminium grill (anodised transparent or dyed to requiredshade according to IS: 1868 with minimum anodic coating of gradeAC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainlesssteel screws @ 200 mm centre to centre, including cutting the grill toproper opening size for fixing and operation of handles and fixingapproved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer in-charge. |
| 11 | S & F in repairs 125x60mm size Pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinge, lock strike plate, etc. complete as specified. |
| 12 | S & F in repairs 105x60mm size Pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinge, lock strike plate, etc. complete as specified. |
| 13 | S&F factory made soild PVC moulded dorr shutter 28 to 30 mm thick(stiles), with 2,4 or 6 raised panel design with 2 mm thick moulded PVC sheet on the front face & 2 mm plain color pvc sheet on back face supplying and fixing in frame complete all as specified and directed |
| 14 | S&F PVC Door Frame for moulded door shutter of size 50mmx47mm made out of 5mm colour PVC sheet reinfoced with MS Square tub, suppling & fixing in opening as per specification and drawing. |
| 15 | S&F 125 mm Butt hinges, meduim weight, cold relled stainless steel and fixed complete all as specified and directed |
| 16 | S & F for aluminium anodised, barrel tower bolts of extruded section 150 mm long and fixed complete all as specified and directed |
| 17 | S&F 4mm thick Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified. |
| 18 | S&F 35 mm thich 2nd class Hard wood Glazed and skelton shutters, open rebated and prepared to receive glass, guaze etc, divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars any numbers, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securiing glass etc, sizes of members of shutters as specified in SSR Part-I, Section 8, clause 8.20(a) and fitted to chowkats. |
| 19 | S&F 30mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both side. |
| 20 | S & F for Galvanised mildsteelwire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples |
| 21 | S&F 250mm Aluminium alloy, anodised, sliding door bolt with hasp, staple(bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of exctruded sections or cast aluminium alloy and fixed. |
| 22 | S & F for mild steel 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed |
| 23 | M&L Glazed coloured ceramic tiles in vertical surfaces 450x300x7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10 mm thick in cement mortar 1:3 on fair faces of brick work or concrete surface as backing coat coat of dado/skirting etc complete all as specified and as directed . |
| 24 | M&L Non skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile 0.18 Sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick Screed bed or bedding layer of mortar for lying floor finished in Cement Mortar 1:4 complete all as specified and as directed . |
| 25 | M&L Non skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick Screed bed or bedding layer of mortar for lying floor finished in Cement Mortar 1:4.. |
| 26 | M&L 25mm thick Cement concrete 1:2:4 type B-O(using 12.5mm graded aggregate) as in flooring, finished surfaces even and smooth without using extra cement. |
| 27 | M&L for rendering 15 mm thick in CM (1:3) mixed with water proofing compound @ 3% by weight of cement finishedeven and smooth without using extra cement in sunken portion of toilet etc complete all as specified and as directed Note: WPC will be measured and paid separtely |
| 28 | M&L for two coat of painting with Dr Fixit fast Flex (or equivalent) water proofing liquid including preparation of new plastered surfaces complete all as specified and as directed by Engineer-in-Charge. |
| 29 | M&L cement concrete 1:5:10 type E-2 using 20mm granded crushed Brick aggregates as in sunken portion of WC etc complete all as specified and as directed |
| 30 | Taking up or down steel tubing 15 mm bore, and connections, including cleaning for re-fixing or removal to store in repairscomplete all as specified. |
| 31 | Taking up or down steel tubing 20mm bore, and connections, including cleaning for re-fixing or removal to store in repairscomplete all as specified. |
| 32 | S&F 15 mm bore CPVC tubeswith all fittings and fixed complete to walls and ceilings or laid in floors. |
| 33 | S&F 20 mm bore tubes medium grade galvanised with all fittings and fixed complete to walls and ceilings or laid in floors. |
| 34 | S & F in repairs 15mm bore Bib taps, fancy type chromium plated cast copper alloy with crutch or butterly handle, screwed down, screwed with cupfor iron pipe or for brass ferrule and fixed complete all as specified and directed |
| 35 | S & F in repairs 15mm bore Stop Valve/ angle valve fancy type chromium plated , cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends with cup for iron pipe or for unions and fixed complete all as specified and directed. |
| 36 | S & F in repairs 15mm bore Pillar tapscentral hole Basin mixer with regular spout without popup waste system with 450 mm long braided hosedd 20 mm carttridge size fancy type,cast copper alloy,chromium plated, complete all as specified and directed. |
| 37 | S & F in repair single towel rall 450mm long fancy type chromium plated fixed with PVC plug and steel screw complete all as specified and directed. |
| 38 | S & F in repair towel ring round with round flange fancy type cromium plated fixed with PVC plug and steel screw complete all as specified and directed. |
| 39 | S & F in repair soap dish, vitreous China white, approximate size 160x 160x90mm complete all as specified and directed. |
| 40 | M & L in repair for hand shower (health faucet) with 18mm dia 1.20 m long(min) flexible tube and wall hook complete all as specified and directed. |
| 41 | S & F in repairfor PVC conection 15 mm size with PTMT nuts of length 450 mm long complete all as specified and directed |
| 42 | S & F in repair Swivel shower of PTMT any colour forfixing with 15mm pipe. (Minimum weight40gms complete all as specified and directed. |
| 43 | S&F in repair vitreous China wash basin white, flat back (min size 550x400 mm or as required) including S&F 32mm dia waste coupling, waste PVC pipe complete all as specified and as directed. |
| 44 | S&F in repair vitreous ChinaSquatting pan \"Orrisa\" pattren size(min size 580x440mm) white with integral foot rest, \"P\" or \"S\" trap cement concrete beddingcomplete all as specified and directed. |
| 45 | Supply only 10 Ltr capacity PVC valveless symphonic action type flushing cistern white low level with ball valve float, handle including bracket complete all as specified and directedwith glaged finish. |
| 46 | M&L for 15mm thick Rendering on fair faces of brick work or concrete sureces in Cement Moratar 1:6 finished surface even and smooth without using extra cement.Note the area includs in this up to 4th stories building |
| 47 | M&L for 15mm thick Rendering on fair faces of brick work or concrete sureces in Cement Moratar 1:4 finished surface even and smooth without using extra cement. Note the area includs in this up to 4th stories building |
| 48 | M&L for 10mm thick Rendering on ceiling surface fair faces of brick work or concrete sureces in Cement Moratar 1:3 finished surface even and smooth without using extra cement. Note the area includs in this up to 4th stories building |
| 49 | S& F in repair stain less steel decorative cutrain rod of 25 mm bore inluding 2 nos steel finale and bracket 02 nos etc and fixed to wall with plastic rowl plug and steel screw complete all as specified and directed. |
| 50 | S & F 600mm x 450mm mirror of thickness 5.0 mm with chromium plated brass spacers 25 to 30 mm in size in each corner including rounding the edges of the mirror and fixed-in-repairs complete all as specified |
| 51 | M & L for prepring old plaster surface by applying 1-2 mm thick wall care putty applying one coat Oil Bound distember on wall surface with roller brush complete all as specified and directed. |
| 52 | M & L for newplaster surface applying two coat Oil Bound distember on wall surface with roller brush complete all as specified and directed. |
| 53 | M & L for prepring old plaster surface applying one coat of oil bound distemper on ceiling surface with roller brush complete all as specified and directed. |
| 54 | M & L preparing newly plastered surfaces of wall by appliying wall putty 1 to 1.5 mm thick, cutting/rubbing to obtained a smooth surface and applying two coats of weather coat exterior paint with approved tint over a coat of primer (as per Manufacturer\"s) |
| 55 | M&L preparing old Decorated/Treated/roughPlastered surfaces of Wallsby brooming down or steel wire brushing and scraping downand applying one Coat of Weather Coat Exterior Paint (in Camuflage/Plain pattern as ordered) with approved Tint(as per Manufacturer\"s instructions), complete all as specified and as directed. |
| 56 | M&L applying subsequent Coats of Weather Coat Exterior Paint (in Camuflage/Plain pattern as ordered) with approved Tint(as per Manufacturer\"s instructions), complete all as specified and as directed. |
| 57 | M&L for preparing new wooden surfaces of any description, not otherwise described over 10cm in width or girth and applying two coats of synthetic enamel paint over pink primer. |
| 58 | M&L Preparing old painted surfaces of wood of any description, not otherwise described, over 10cm width or girth and one coat of synthetic enamel paint. |
| 59 | M&L for preparing old painted steel and iron surfaces of any description, over 10cm in width or girth, not otherwise described and applying one coat of synthetic enemal paint complete all as specified and directed. |
| 60 | Taking down existing damaged APP membrane and clean the surface , frost, surface laitance and contamination and free from loose aggregate, iclean with water complete all as directed by Engr-in-Charge. |
| 61 | M&L for PCC 1: 2 :4 Type B-1 (using 12.5 mm graded stone aggregate) as in padding over roof slab laid to slope finished even and smooth, roof kerbs or mud stops, rounded or chamfered on edges complete all as specified and directed.(Note : Rates are included upto G+2 Storey) |
| 62 | M&L for 10 mm thick cement plaster with CM 1:4 smooth finish for application of waterproof coating primer the surface clean with water complete with making the corner plain and smooth all as directed by Engr-in-Charge.(Note : Rates are included upto G+2 Storey) |
| 63 | Supply only Integral Water Proofing Compound, ISI Marked, as approved, complete all as specified and as directed. |
| 64 | M&L for cleaning the newly plastered surfaces thoroughly with wire brushes and providing water proofing treatment all as specified here in after :-(a) Bituminous primer @ 0.30liter per sqm conforming to IS 3384-1986 (b) 3mm thick APP polymeric membrane minimum weighing 3 Kg/Sqm laid by torch application method with over laps of 100 mm joints of traverse direction and 75 mm at longitudinal direction duly thermofused by flame torch all as specified in application manuel of the company |
| 65 | M&L for applying aluminium paint(Each coat) @ 100ml/Sqm over APP membrane all as specified and directed |
| 66 | Supply and fix Godrej pattern mild steel cup board with shutter made out of 1.00 mm thick M.S. sheet60cm depth sides incl with back & 3 shelves & vertical partition & mild steel door shutter two leaves with frame, incl necessary fittings with locking arrangement and handle etc all as per Godrej Pattern with duplicate keys including necessary fittings & two coats of spray painting over a coat of red oxide zinc chromate primer complete and dismantling of old/rusted cupboard frame and shelves. The cost of grouting them in CM (1:3) is deemed to be included in unit rates (Only front face of cupboard to be measured)complete all as specified and as directed . |
| 67 | Demolition of brick work or stone/boulders Masonry/concrete surface built in cement mortar or cement lime mortar including all quions, arches, pillars, ect but excluding ashlar facings dressed stone work and precast concrete articles. |
| 68 | M&L for brick work with sub class \"B\" brick, straight or curved on plan exc 6.0 mtr mean radius built in CM 1:4 etc complete all as specified and directed |
| 69 | M&L for brick work with sub class \"B\" brick, straight or curved on plan exc 6.0 mtr mean radius built in CM 1:4 etc complete all as specified and directed (except Bricks) |
| 70 | M&L for PCC 1:3:6 type B1 using 20mm graded stone aggregate asin floor 40 mm thick finishing the surface without using extra cement complete all as specified |
| 71 | Taking downcement or cement lime plaster on brick or stone walls, etc.including raking out joints, hacking for key, scrubbing down with water, etc |
| 72 | M&L for rendering 15 mm thick in CM 1:4, finished even and smooth without using extra cement complete all as specified and as directed |
| 73 | M & L for prepring any type of newly plasetered surface of walls and applying two coats of weather coat exterior paint ( in camouflage/plain pattern as directed) over a coat of primer ( as per manufacturer\"s instruction) all as specified and directed. |
| 74 | Excavation in trenches n.exc 1.50mtr wide and 1.50mtr in depth for foundation etc or for shafts, wells cessipts, manhole etc not exceeding 10 Sqm on plan and not exceeding 1.5 mtr deth and getting out in soft /loose soil etc complete all as specified and as directed |
| 75 | Excavation over areas 1.50 mtr in depth for foundation etc or for shafts, wells cessipts, manholeand getting out in soft /loose soil etc complete all as specified and as directed |
| 76 | Surface excavation in any type of soil n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out |
| 77 | Returning filling in, with soil inlcuidng spreading, levelling,watering and well ramming in layers not exc 25 cm thicks etc complete all as specified and as directed |
| 78 | Removing excavated soil/ building material/debries to a distance exc 250 mtr but not exceeding 500 mtr and depositing where directed etc complete all as specified and directed |
| 79 | M&L for cement concrete 1:4:8 type D-2 (using 40mm graded aggregates) as in foundation and mass concrete etc complete all as specified and directed |
| 80 | M&L for cement concrete 1:2:4 type, B1 using 20 mm graded stone aggregates as in copings including necessary use and waste formwork, weathering, slightly rounded or chamfered angles and throating etc complete all as specified and directed |
| 81 | Earth work excavation in post holes ( or similar holes) in hard/dense soil ,each not exceeding 0.50 Cum ,getting out ,returning filling in and ramming earth or broken rubble mixed with earth around ,in layers not exceeding 25 cm ,watering and removing surplus soil. |
| 82 | S&F Framed mild steel work as in posts/ struts in fencingincluding cutting tops to shape, drilling holes,bolting,rivetting flatetc. complete conforming to Fe-290 gde E165 all as spd and directed |
| 83 | S&F Framed mild steel work as in gates including pintel hinges, stops, hand made sliding bolts etc. complete conforming to Fe-410-0 or Fe-310-0 all as spd and directed |
| 84 | Desigining and providing and fixingAluminium Composite Clading 3mm thick with FR grade mineral core sandwiched between two aluminium sheets (each 0.5mm thcik) of over RCC/Brick surfaces either segmental/ straight in plan wherever specified with extruded aluminium U section, angle, cleats, weather sealants, backer rods of required size stailess steel screws,rivets,brackets,drilling and fixing the cladding to either masonary or reinforced cement concrete as the case may be manufacturer\"s specifications, complete the work in all necessary accessories. At all soffits aluminium cladding shall be bend 90 degree and joints at corner or edges will not be acceptable. On horizontzl surfaces, the size of sheet should be maximum available of size complete all as per manufacturer\"s specification and as directed by Engr-In-Charge. |
| 85 | S&F 30-35 mm thick GRC/GFRC Jali by drilling or patching it in walls/RCC Columns including dismantling old RCC jali all as specified anddirected |
| 86 | One coat of synthetic enamel paint on old painted steel surfaces of any description over 10 cm width or girth including preparation of surfaces all as specified and as directed. |
| 87 | Dismantling of plain or corrugated steel sheeting or mangalore tile roof any guage, thickness from roof covering complete all as specified. |
| 88 | S&F for Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screwscomplete all as specified. |
| 89 | S&FRoof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. .Fe-410- W(Gde E-250)quality-B |
| 90 | Preparing new steel or iron surfaces all as specified |
| 91 | M&L forcoat of red oxide primer on steel surface |
| 92 | M&L forcoat of synthetic enamel paint on steel surface |
| 93 | M&L forapplying one coat of synthetic enamel paint over concrete surface/kerb stone |
| 94 | M & L for Precast coloured ceramic pavement tiles 300x300x7-8 mm thick laid in floorings as per manufacturer size over a screed bed of CM 1:6, 20 mm thick all as specified. |
| 95 | Machine pressed precast concrete interlocking paver block with glossy finish any shape and size confirming to IS 15658 – 2006 of 60 mm thickness, M-35 Grade, with grey cement and pigment,over new sub-baselaid over and including 20mm thick screed be complete all as specified. |
| 96 | M&L for cobble stone of any shape and size of 60 mm thickness, with grey cement and pigment,over new sub-baselaid over and including 20mm thick screed be complete all as specified. |
| 97 | M&L for 20-25 mm thick precast chequeredtiles glossy finish of size 300 x 300 mm, coloured, pre-polished, set and jointed in neat cement slurry and pointed in coloured cement to match with the shade of tiles, as in floor, laid over and including 20mm thick screed bed i, all as specified and as directed. |
| 98 | M&L for preparing old plastered surafce of compound wall |
| 99 | M&L for applying one coat of acrylic smooth exterior paint of required shade and making blue line of width 300-450 mm at desired intervalsall as specified and directed |
| 100 | Fixing in repair only Galvanised. 2 strand, steel barbedwire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails strain- ing bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured) |
| 101 | (Note : Completion shall be issued once all the debries is removed from the MOD land.) |
