|
| 1 | Excavation in Soil using Hydraulic Excavator CK 90 and Tippers with Disposal- Excavation for roadwork in soil with hydraulic excavator of 0.9 cum bucket capacity including cutting and loading in tippers, trimming bottom and side slopes, in accordance with requirements of lines, grades and cross sections, and transporting to the embankment location within all lifts as per MORT&H specification 301. I/C cost of material, labour, T&P and all Taxes but Excluding GST |
| 2 | Construction of Embankment with Material Deposited from Roadway Cutting :-Construction of embankment with approved materials deposited at site from roadway cutting and excavation from drain and foundation of other structures graded and compacted to meet requirement of table 300-2. I/C cost of material, labour, T&P and all Taxes but Excluding GST |
| 3 | Construction of Embankment with Material obtained from Borrowpits - Construction of embankment with approved material obtained from borrow pits with all lifts & transporting to site, spreading, grading to required slope and compacting to meet requirement of table 300-2. I/C cost of material, labour, T&P and all Taxes but Excluding GST |
| 4 | Construction of Embankment with Material obtained from Borrowpits (Lead 2Km.) :-Construction of embankment with approved material obtained from borrow pits with all lifts and leads with 2 Km, transporting to site, spreading, grading to required slope and compacting to meet requirement of table 300-2 I/C cost of material, labour, T&P and all Taxes but Excluding GST |
| 5 | By Mix in Place Method Construction of granular sub-base by providing close graded Material, spreading in uniform Layes with moter grader on prepared surface, mixing by min place method with front end loader at OMC, and compacting with vibratory roller to achieve the desired density, complete as per clause 401 I/C cost of material, labour, T&P and all Taxes but Excluding GST |
| 6 | WMM - Providing Laying Spreading and Compacting grade Stone aggregates of wet mixed macadem (In layers) specification including premixing the meterial with water at OMC Mechnical Mix Plant carriage of mixed material by tipper to site, laying in uniform layers with paver in subbase / base course of well prepared surface and compacting with vibratry roller to achive the desired Compation. (MoRT&H Specification No. 406) I/C cost of material, labour, T&P and all Taxes but Excluding GST |
| 7 | Prime Coat Providing and applying primer coat with SS2 grade bitumen emulsion on prepared surface of granular Base including clearing of road surface and spraying primer at the rate of 0.70 kg/sqm using mechanical means. I/C cost of material, labour, T&P and all Taxes but Excluding GST |
| 8 | Tack Coat (For Bituminous surface): -Providing and applying Tack coat with bitumen VG-10 on prepared bituminous surface including cleaning of road surface and spraying tack coat at the rate of 0.20kg sqm using mechincal means & complet as per MoRT&H Specification No. 503. I/C cost of material, labour, T&P and all Taxes but Excluding GST |
| 9 | Dense Graded Bituminous Macadam Grading II Providing and laying dense graded bituminous macadam with higher capacity batch type HMP using crushed aggregates of specified grading, premixed with bituminous binder VG-30 @ 4.5 per cent by weight of total mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MoRTH specification clause No. 505 complete in all respects. I/C cost of material, labour, T&P and all Taxes but Excluding GST |
| 10 | Bituminous Concrete:-Providing and laying bituminous Concrete Grading-II with 100-120 TPH batch type HMP producing an average output of 75 tonnes per hour using crushed aggregrates of specified grading premixed with bituminous binder VG-30, @ 5.4 % of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade. level and alignment and rolling with smooth wheeled vibatory and tandem rollers to achive the desired compaction as per MOTRH specification Clause 507 complete in all respect I/C cost of material, labour, T&P and all Taxes but Excluding GST |
| 11 | Cement Concrete Pavement :-Construction of un-reinforced, dowel jointed, plain cement concrete pavement M-35 over a prepared sub base with 43 grade OPC cement (Make J.P., ACC, Birla or J.K.) coarse and fine aggregate conforming to IS 383, maximum size of coarse aggregate not exceeding 25 mm, replacing cement by fly ash to the extent of 15 per cent and sand by 10 per cent, mixed in a batching and mixing plant as per approved mix design, transported to site, laid with a fixed form or slip form paver, spread, compacted and finished in a continuous operation including provision of contraction, expansion, construction and longitudinal joints, joint filler, separation membrane, sealant primer, joint sealant, debonding strip, dowel bar, tie rod, admixtures as approved, curing compound, finishing to lines and grades as per drawing I/C cost of material, labour, T&P and all Taxes but Excluding GST |
| 12 | S/F of 5th Kilometer Stone & lettring Painting etc. I/C cost of material, labour, T&P and all Taxes but Excluding GST |
| 13 | S/F of Kilometer Stone & lettring Painting etc. I/C cost of material, labour, T&P and all Taxes but Excluding GST |
| 14 | S/F of Hectometer Stone & lettring Painting etc. I/C cost of material, labour, T&P and all Taxes but Excluding GST |
| 15 | Dismantling brick work or stone work in lime or cement mortar and including stacking of materials as directed by Engineer-In-Charge within a distance of 60 meters (200 feet). SOR Ch.17 SI No.692 I/C cost of material, labour, T&P and all Taxes but Excluding GST |
| 16 | Dismantling reinforced cement concrete or reinforced brick work including stacking of dismantled materials as directed by Engineer-In-Charge within a distance of 60 meters (200 feet). SOR Ch.17 SI No.694 I/C cost of material, labour, T&P and all Taxes but Excluding GST |
| 17 | Construction of Embankment with Material obtained from Borrowpits (Lead 2Km.) :-Construction of embankment with approved material obtained from borrow pits with all lifts and leads with 1 Km, transporting to site, spreading, grading to required slope and compacting to meet requirement of table 300-2 I/C cost of material, labour, T&P and all Taxes but Excluding GST |
| 18 | Dewatering work of undergrounding water as well as surface water with the help of diesel engine pumping set during earth work in excavation of foundation for laying lean concrete and brick work in foudation (or as required), hire charging of pumping set, Fuel charge, labour and other T&P including cost of operation as per requirement at site & as direction by Engineer-in-Charge. I/C cost of material, labour, T&P and all Taxes but Excluding GST |
| 19 | Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom and backfilling with approved material. As per Morth Specification 304(B) I/C cost of material, labour, T&P and all Taxes but Excluding GST |
| 20 | Plain Cement Concrete in Open Foundation complete as per Drawing and Technical Specifications. 1500, 1700 & 2100 Sr 12.08 (P.C.C. Grade M-15) I/C cost of material, labour, T&P and all Taxes but Excluding GST |
| 21 | Plain/Reinforced cement concrete in sub-structure complete as per drawing and Technical Specifications. 1500, 1700 & 2200 (P.C.C. Grade M-20) I/C cost of material, labour, T&P and all Taxes but Excluding GST |
| 22 | Plain/Reinforced Cement Concrete in Open Foundation complete as per Drawing and Technical Specifications 23.05, 1500, 1700 & 2100 Sr 12.08 (R.C.C. Grade M-30) I/C cost of material, labour, T&P and all Taxes but Excluding GST |
| 23 | Rainforce cement concrete in sub-structure complete as per drawing and Technical Specifications 1500, 1700 & 2200 sr no. 13.05. (RCC Grade M-30) I/C cost of material, labour, T&P and all Taxes but Excluding GST |
| 24 | Sand Filling in Foundation Trenches as per Drawing & Technical Specification. As per MORTH Specification No. 304, S.I. 12.3 I/C cost of material, labour, T&P and all Taxes but Excluding GST |
| 25 | R.C.C. M-30 :- Providing and laying reinforced cement concrete in superstructure as per drawing and technical specifications clauses 800, 1205.4 and 1205.5 I/C cost of material, labour, T&P and all Taxes but Excluding GST |
| 26 | Providing and laying cement concrete wearing coat M-30 grade excluding reinforcement complete as per drawing and technical specification clause 800 and 2702 I/C cost of material, labour, T&P and all Taxes but Excluding GST |
| 27 | Supplying, fitting and placing HYSD (Fe-500) bar reinforcement in foundation, substructure & superstructure complete as per drawings and technical specification clauses 1600 . I/C cost of material, labour, T&P and all Taxes but Excluding GST |
| 28 | Providing weep holes in Brick masonry/Plain/ Reinforced concrete abutment, wing wall/ return wall with 100 mm dia PVC pipe, extending through the full width of the structure with slope of 1V :20H towards drawing foce. Complete as per drawing and Technical Specifications I/C cost of material, labour, T&P and all Taxes but Excluding GST |
| 29 | Drainage Spouts complete as per drawing and Technical specification. As per MORT&H Specification No. 14.9 I/C cost of material, labour, T&P and all Taxes but Excluding GST |
| 30 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. I/C cost of material, labour, T&P and all Taxes but Excluding GST |
| 31 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on old work including cost of all material, Labour, T&P etc. complete required for proper completion of the work. I/C cost of material, labour, T&P and all Taxes but Excluding GST |
| 32 | Providing and laying of 40 mm gauge B/B under Hume pipe culvert foundation in road work including all materials, labours, T&P etc. required for completion of the work. CH-20, Sl.no. 18 I/C cost of material, labour, T&P and all Taxes but Excluding GST |
| 33 | Brick Masonry Work in Cement Mortar 1:3 in Foundation complete excluding Pointing and Plastering, as per Drawing and Technical Specifications 1300. I/C cost of material, labour, T&P and all Taxes but Excluding GST |
| 34 | Supply, laying and fixing of NP3 class hume pipes in proper position in culvert. Hume Pipe 350 mm Dia Culvert I/C cost of material, labour, T&P and all Taxes but Excluding GST |
| 35 | Supply, laying and fixing of NP3 class hume pipes in proper position in culvert. Hume Pipe 600 mm Dia Culvert I/C cost of material, labour, T&P and all Taxes but Excluding GST |
| 36 | Supply, laying and fixing of NP3 class hume pipes in proper position in culvert. Hume Pipe 1000 mm Dia Culvert I/C cost of material, labour, T&P and all Taxes but Excluding GST |
| 37 | Pointing with cement mortar (1:3 ) on brick work in substructure as per Technical Specifications I/C cost of material, labour, T&P and all Taxes but Excluding GST |
| 38 | Plastering with cement mortar (1:3 ) on brick work in sub-structure as per Technical Specifications I/C cost of material, labour, T&P and all Taxes but Excluding GST |
| 39 | White washing with lime on undecorated wall surfaces (Two coats) to give an even shade including thoroughly brooming the surface to remove all dirt, dust mortar drops and loose scales of lime wash and other foreign matters. as per SOR CH 16, (SI.No. 672) I/C cost of material, labour, T&P and all Taxes but Excluding GST |
| 40 | Road Marking with Hot Applied Thermoplastic Compound with Reflectorising Glass Beads on Bituminous Surface. Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35-2015 The finished surface to be level, uniform and free from streaks and holes. I/C cost of material, labour, T&P and all Taxes but Excluding GST |
| 41 | 6M Span overhead Cantilever Structure with 300dia MS one vertical post :- Supply, fixing & erection of built up Cantilever Structure 6 m span comprising of one vertical posts of 6.00 M height made up of 300 mm NB heavy class MS pipe as vertical member welded with 10 mm MS plate at top & 12 mm M S plate at bottom. The horizontal Truss shall comprise of 50 mm dia heavy class M. S. pipe and 40 mm dia heavy M S pipe as bracing & 10 mm M$ plate at bottom for fixing to vertical post as per structure design & drawing with one of steel primer and two coats of synthetic enamel plant. The work includes construction of RCC Foundation of size 0.90×0.90×1.50 m of required depth as per site condition for built up structure including Earth work in excavation 100 mm thick Lean Concrete in 1:3:6 cement coarse sand and 40 mm gauge stone ballast and RCC - M25 grade concrete including supply and fixing of 25 mm dia Foundation Bolts 600 mm long as per provision of structure design including cost of reinforcement & shuttering. The lateral vertical clearances and complete installation work shall be as per relevant clauses of MORT&H specification section 800 and IRC 67: 2012 complete in all respect The Rates shall include cost of design fabrication, supply, transportation Local shifting Erection of Signage structure using crane, inclusive of all taxes etc. all T&P machine, material and labour required for proper completion of work as per direction of Engineer-in-charge. I/C cost of material, labour, T&P and all Taxes but Excluding GST |
| 42 | Retro-Reflective Sheeting type-IV with 4 mm thick ACM Single Side-Providing & fixing of reflective signs with a corrosion resistant 4 mm thick with 0.4 to 0.5 mm both side aluminium skin aluminium composite panel face to be fully covered with High Intensity prismatic sheeting type IV as per IRC-67:2012 retro reflective sheeting with back frame MS angle of 35x35x5 mm. Legends, letters, numerals and borders etc should be as per MORTH specification No-801.3.7. The sheeting shall have a pressure - sensitive adhesive of the aggressive - tack type requiring no heat solvent other preparation for adhesion to a smooth clean surface, in a manner recommended by the sheeting manufacturer. The ACM (Aluminum Composite Materials) shall be fixed on the Back frame MS Angle with riveting. Micro prismatic type IV Retro reflective sheeting confirming to ASTM D4958-09 shall be Pressure fixed, The Retro reflective sheeting shall be listed for a certificate of having the sheeting tested for coefficient of retro reflection, daytime colour and luminance, shrinkage, flexibility, liner removal, adhesion, impact resistance, specular gloss and fungus resistance, 3 years outdoor weathering and its having passed these tests shall be obtained from International/Government Laboratory/Institute by the manufacturer of the sheeting and in case the certificate is obtained from international condition, it should also be obtained from Indian condition within 3 years of launching of product by the manufacture in abroad. Alternatively, a certificate conforming to ASTM Specification (D 4956-09) on artificial accelerated weathering requirements from a reputed laboratory in India can be accepted provisionally. In such a situation, the Employer/Client, if so desires, could seek for a performance guarantee which would be released after receipt of certificate meeting the requirement of three years outdoor weathering of the sheeting as per IRC 67:2012 & Proof of the same Report shall be uploaded which quoting tender. The rate shall include all materials, labour, T&P, transportation, installation and incidentals all complete as per direction of the Engineer-in-Charge. I/C cost of material, labour, T&P and all Taxes but Excluding GST |
| 43 | Retro-reflectorised Traffic sign as per IRC-67-2012:Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC :67-2012 made of high intensity grade sheeting type-IV vide clause 801.3, fixed over aluminium sheeting 1.5 mm thick supported on a mild steel angle iron post 75 mm×75 mm×6 mm firmly fixed to the ground by means of properly designed foundation with M 15 grade cement concrete 45 cm×45 cm×60 cm. 60 cm below ground level as per approved drawing. The Retro reflective sheeting shall be tested for a certificate of having the sheeting tested for coefficient of retro reflection, daytime colour and luminance, shrinkage, flexibility, liner removal, adhesion, impact resistance, specular gloss and fungus resistance, 3 years outdoor weathering and its having passed these tests shall be obtained from International/Government Laboratory Institute by the manufacturer of the sheeting and in case the certificate is obtained from international condition, it should also be obtained from Indian condition within 3 years of launching of product by the manufacture in abroad. Alternatively, a certificate conforming to ASTM Specification (D 4956-09) on artificial accelerated weathering requirements from a reputed laboratory in India can be accepted provisionally. In such a situation, the Employer/Client, if so desires, could seek for a performance guarantee which would be released after receipt of certificate meeting the requirement of three years outdoor weathering of the sheeting as per IRC 67.2012. Legends, letters, numerals and borders etc should be as per MORTH specification No-801.3.7. Proof of the same in form of government report shall be uploaded while quoting tender ii) 60cm Circular with diffinitation plate (20cmx60cm) Mandatory (Speed limit) I/C cost of material, labour, T&P and all Taxes but Excluding GST |
| 44 | Retro-reflectorised Traffic sign as per IRC-67-2012:Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC :67-2012 made of high intensity grade sheeting type-IV vide clause 801.3, fixed over aluminium sheeting 1.5 mm thick supported on a mild steel angle iron post 75 mm×75 mm×6 mm firmly fixed to the ground by means of properly designed foundation with M 15 grade cement concrete 45 cm×45 cm×60 cm. 60 cm below ground level as per approved drawing. The Retro reflective sheeting shall be tested for a certificate of having the sheeting tested for coefficient of retro reflection, daytime colour and luminance, shrinkage, flexibility, liner removal, adhesion, impact resistance, specular gloss and fungus resistance, 3 years outdoor weathering and its having passed these tests shall be obtained from International/Government Laboratory Institute by the manufacturer of the sheeting and in case the certificate is obtained from international condition, it should also be obtained from Indian condition within 3 years of launching of product by the manufacture in abroad. Alternatively, a certificate conforming to ASTM Specification (D 4956-09) on artificial accelerated weathering requirements from a reputed laboratory in India can be accepted provisionally. In such a situation, the Employer/Client, if so desires, could seek for a performance guarantee which would be released after receipt of certificate meeting the requirement of three years outdoor weathering of the sheeting as per IRC 67.2012. Legends, letters, numerals and borders etc should be as per MORTH specification No-801.3.7. Proof of the same in form of government report shall be uploaded while quoting tender iii) 80mmx60mm rectangular with diffinitation (20cmx60cm) Informetory Board I/C cost of material, labour, T&P and all Taxes but Excluding GST |
| 45 | Retro-reflectorised Traffic sign as per IRC-67-2012:Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC :67-2012 made of high intensity grade sheeting type-IV vide clause 801.3, fixed over aluminium sheeting 1.5 mm thick supported on a mild steel angle iron post 75 mm×75 mm×6 mm firmly fixed to the ground by means of properly designed foundation with M 15 grade cement concrete 45 cm×45 cm×60 cm. 60 cm below ground level as per approved drawing. The Retro reflective sheeting shall be tested for a certificate of having the sheeting tested for coefficient of retro reflection, daytime colour and luminance, shrinkage, flexibility, liner removal, adhesion, impact resistance, specular gloss and fungus resistance, 3 years outdoor weathering and its having passed these tests shall be obtained from International/Government Laboratory Institute by the manufacturer of the sheeting and in case the certificate is obtained from international condition, it should also be obtained from Indian condition within 3 years of launching of product by the manufacture in abroad. Alternatively, a certificate conforming to ASTM Specification (D 4956-09) on artificial accelerated weathering requirements from a reputed laboratory in India can be accepted provisionally. In such a situation, the Employer/Client, if so desires, could seek for a performance guarantee which would be released after receipt of certificate meeting the requirement of three years outdoor weathering of the sheeting as per IRC 67.2012. Legends, letters, numerals and borders etc should be as per MORTH specification No-801.3.7. Proof of the same in form of government report shall be uploaded while quoting tender vii) 30x90 cm Hazard I/C cost of material, labour, T&P and all Taxes but Excluding GST |
| 46 | Road Delineator Delineator: Supply & Fixing of MS Delineator made of Mild steel with pure polyester powder coating with the minimum thickness of powder coating of not less than 40 micron for protection against corrosion. The surface should be concealed so that there should not be any exposed surface without powder coating. Alternatively, these metal guide poles can be concealed with thermoplastic body. The posts shall have lan ellipsoidal or circular design with the height of the pole shall be 800 to 900 mm above the ground with about 200 to 300 mm base which can be anchored onto the ground. Mild steel Guide Poles shall conform to Type XI sheeting specifications as per IRC:67 and ASTM D4956 which would ensure to obtain clear visibility of the road alignment during night time. The Retro reflective sheeting shall be tested for A certificate of having the sheeting tested for coefficient of retro reflection, daytime colour and luminance, shrinkage, flexibility, liner removal, adhesion, impact resistance, specular gloss and fungus resistance, 3 years outdoor weathering and its having passed these tests shall be obtained from International Government Laboratory/Institute by the manufacturer of the sheeting and in case the certificate is obtained from international condition, it should also be obtained from Indian condition within 3 years of launching of product by the manufacture in abroad. Alternatively, a certificate conforming to ASTM Specification (D4956-09) on artificial accelerated weathering requirements from a reputed laboratory in India can be accepted provisionally. In such a situation, the Employer/Client, if so desires, could seek for a performance guarantee which would be released after receipt of certificate meeting the requirement of three years outdoor weathering of the sheeting as per IRC 67:2012 & Proof of the same Report shall be uploaded which quoting tender. The rate shall include all materials, labour T&P. transportation, installation and incidentals all complete as per direction of the Engineer-in-Charge. I/C cost of material, labour, T&P and all Taxes but Excluding GST |
| 47 | Road Marking with Hot Applied Thermoplastic Compound with Reflectorising Glass Beads on Bituminous Surface. (Repeated/ Transverse bar):-Providing and laying of hot applied thermoplastic compound 5 mm thick including reflectorising glass beads @ 500 gms per sqm area, thickness of 5 mm is exclusive of surface applied glass beads as per IRC:35-2015 The finished surface to be level, uniform and free from streaks and holes. I/C cost of material, labour, T&P and all Taxes but Excluding GST |
| 48 | Type - A, \"W\": Metal Beam Crash Barrier :-Providing and erecting a \"w metal beam crash barrier comprising of 3 mm thick corrugated sheet metal beam rail, 70 cm above road/ground level, fixed on ISMC series channel vertical post, 150×75×5 mm spaced 2 m centre to centre, 1.8 m high. 1.1 m below ground/road level, all steel parts and fitments to be galvanized by hot dip process, all fittings to conform to IS: 1367 and 18:1364, metal beam rail to be fixed on the vertical post with a spacer of channel section 150×75×5 mm, 330 mm long complete as per clause 810. I/C cost of material, labour, T&P and all Taxes but Excluding GST I/C cost of material, labour, T&P and all Taxes but Excluding GST |
| 49 | Maintenance Charges for Bituminous Road PartMaintenance Charge including repair of painted surface, earthwork on patri etc complete as per direction of E.I. for the period of five years from the actual date of completion of work. (From Item No. 1 to 48)For First Year @ Zeero % |
| 50 | Maintenance Same as Item No. 49 but for Second Year 0.25% of cost of total executed Work |
| 51 | Maintenance Same as Item No. 49 but for Third Year 0.50% of cost of total executed Work |
| 52 | Maintenance Same as Item No. 49 but for Fourth Year 0.75% of cost of total executed Work |
| 53 | Maintenance Same as Item No. 49 but for Fifth Year 1.00% of cost of total executed Work Please Enable Macros to View BoQ information |
