|
| 1 | Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits,manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft/loose soil complete all as specified and directed. |
| 2 | Excavating in trenchesexc1.5m but not exc 3.0m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n.exc 10sqm on plan and n.exc 1.5m in depth and getting out. in soft/loose soil complete all as specified and directed. |
| 3 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified and directed. |
| 4 | Removing excavated material (soil) n exc 50m and depositing where directed at a level n exc 1.5m above the starting point complete all as specified and directed. |
| 5 | M&L for PCC 1:4:8 type D:2 using 40mm graded crushed stone aggreate as in foundation for pole/stay assembly foundationetc all as specified and directed. |
| 6 | M&L for PCC 1:3:6 type C:2 using 40mm graded crushed stone aggreate as in foundation for pole/stay assembly etcall as specified and directed. |
| 7 | M&L for PCC 1:2:4 type B:2 using 40mm graded crushed stone aggreate as incoping ofincluding necessaryform work and fair finish to exposed surfaces and dismantling old onecomplete all as specified and directed. |
| 8 | M&L well burnt old size sub Class ‘B’ bricks, laidin trenches for cable protection complete all as specified and as directed by the Engineer-in-Charge. |
| 9 | M&L for in repair80mm dia GI pipe Light grade with all necessary fittings laid in trenches, fixed to wall/pole/under road/floor etc for cable protection complete all as specified and as directed. |
| 10 | M&L for in repair50mm dia GI pipe Light gradewith all necessary fittings laid in trenches, fixed to wall/pole/under road/floor etc for cable protection complete all as specified and as directed. |
| 11 | M&L for sand cushioning for protection of underground cable, consolidatedand compacted with clean dry sand complete all as specified and directed. |
| 12 | M&L for Cross arms, bracings, supports,clamps and back plates fabricated from structural steel sections including nuts, bolts, washers,welding, bending cold or hot,drilling holes for bolts, in any shape or size as indicated or directed and inclusive of one primer coat, one under coat and one finishing coat of aluminum paint complete all as specified & directed. |
| 13 | Taking out old/Unsv damagedexisting steel/concrete poles of any size/length from existing position etc and demolition of PCC foundation and removing the same from site complete all as specified and directed. |
| 14 | Supply and erecting steel tubular pole, swaged, complete with cast iron base plate, finial taper plug, bolts, nuts, washer and screws including painting with two coats of aluminium paint over one coat of red oxide primer on all exposed surfaces and tarring with black bituminous paints to portion embedded in PCC including numbering of poles with two coats of synthetic enamel paints, type 410-SP-31 (9 meter long) complete. (Note Excavation & Earth work andPCCfoundation/baseshall be measured and paid separately under relevant items of this BoQ) |
| 15 | S&F in repairs MCCB 63 Amps 4 pole, 415 V, breaking capacity 16 KA,Ics=100% ICU including spreader terminals & connected accessories both ends complete all as specified and directed. |
| 16 | S&F in repairs MCCB 100 Amps 4 pole, 415 V, breaking capacity 16 KA,Ics=100% ICU including spreader terminals & connected accessories both ends complete all as specified and directed. |
| 17 | S&F in repairsMCCB 160 Amps, 4 Pole, 415 V, adjustable type, with breaking capacity 36 KA, Ics=100 % ICU including spreader terminals & connected accessories both ends complete all as specified and directed. |
| 18 | S&F in repairsMCCB 200 Amps, 4 Pole, 415 V, adjustable type, with breaking capacity 36 KA,Ics=100 % ICU including spreader terminals & connected accessories both ends complete all as specified and directed. |
| 19 | S&F in repairsMCCB 250 Amps, 4 Pole, 415 V, Adjustable type, with breaking capacity 36 KA, 100 % ICUincluding spreader terminals & connected accessories both ends complete all as specified and directed. |
| 20 | S&F in repairsMCCB 320 Amps, 4 Pole, 415 V, adjustable type, with breaking capacity 36 KA, Ics=100% ICU including spreader terminals & connected accessories both ends complete all as specified and directed. |
| 21 | S&F in repairsMCCB 400 Amps, 4 Pole, 415 V, adjustable type, with breaking capacity 36 KA, Ics=100% ICU including spreader terminals & connected accessories both ends complete all as specified and directed. |
| 22 | M & L for XLPE insulated GI wire/Strip armoured Electric power cable (Heavy duty) with stranded Aluminium conductor 1100 Volts grade, cross sectional area 150Sqmm 3.5 core laid in trench/pole/on wall completer all as specified and as directed. |
| 23 | M & L for XLPE insulated GI wire/Strip armoured Electric power cable (Heavy duty) with stranded Aluminium conductor 1100 Volts grade, cross sectional area 35Sqmm 3.5 core laid in trench/pole/on wall completer all as specified and as directed. |
| 24 | M & L for XLPE insulated GI wire/Strip armoured Electric power cable (Heavy duty) with stranded Aluminium conductor 1100 Volts grade, cross sectional area 25Sqmm 4.0 core laid in trench/pole/on wall completer all as specified and as directed. |
| 25 | M & L for XLPE insulated GI wire/Strip armoured Electric power cable (Heavy duty) with stranded Aluminium conductor 1100 Volts grade, cross sectional area 16Sqmm 4.0 core laid in trench/pole/on wall completer all as specified and as directed. |
| 26 | Dismantling cross armsof MS channels or angle sections etc complete all as specified and directed. |
| 27 | Dismantling insulators any type any sizes complete all as specifiedand directed. |
| 28 | M&L for repair, serviceing and replacement of unserviceable accessories of LT Panel any make type/size includingwelding, brazing and drilling work etc complete all as specified and directed.including the followings.(a) Tightening of all loose conectiont of cableinside the panel and welding the broken door of the panel.(b)Clean all the rusted busbar through emery paper and fixing insulation heat shrink sleeves through out the busbar including strip connected with out going MCCB.(c) Cutthe damage insulation portion end of cable inside the panel and reconnecting its into positions after fixing the end termintion/Sleeves complete with suitable size of aluminium lugs and stainless steel nut bolts including excavation and earth work in any type of soilfor taking out the existing cable loop to fixing the end joint or reconnection in position.(d) Repair/Replacement ofburn/unserviceable voltmeter, ammeter,indication lamp including control wiring of the panel between voltmeter, Ammeter and their selector switch and CTs .(e)Repair/Replacement of all burn lugs inside the panel.(f) Replacement of all the GI rusted nut, bolts,and washers with made of stainless steel nuts, bolts and washers.(g) Cleanthe dust inside the panel by air blower/vaccum cleaner complete.Note : (a) The cost of nut bolts, washers, insulation tape, lugs etc essentially required to make the panel serviceable shall be deemed to be included in the quoted rate. (b) Other spare parts/accessories shall measured and paid separatelyunder relevant items of schedule. |
| 29 | Supply, installation, testing and commissioning 3 phase and neutral, 415 volts indoor type LT panel of size 1800 mm height X 1400 mm width X 800 mm depth (over all dimension)confirming to IS 8623, CPRI approved, factory fabricated &factroy assembled , waterproof,dust and vermin proof cubical type with locking arrangement , LT Panel made out of suitable size angle iron, channel and fabricated from 2.00 mm thick (minimum) CRCA sheet with anti corrosive coating and finally epoxy polyester powder coating of flint Grey shade (RAL-7032), independently housing for each control switch gear and indicating lamps with & includingbusbars made of pure copperduly insulated with heat retardent fire proof (HRFR) heat shrinkable sleeves of relevant colours. Bus bar shell be properly supported/mounted on epoxy insulators.All live parts and joints shall be insulated with (HRFR) shrouds, conforming to IS, including provn for cable gland and lugs for incoming and out going cable and connecting suitableearth strips .Suitable openable doors shall be provided of all operational switchgear and MCCBs and detchable cover shall be provided on all other accessories including installation of panel .Panel shall be manufactured suitable for housing and including the following duly control wiring with multistranded copper condutor FRLS with colour coding incl connection with copper lugs complete for 3 phase 50 Hz electric supply :- |
| 30 | Incoming:(a) Copper strip busbar of current carrying capacity 800 Amps wrapped with PVC sleeves with maintained the colour code and provision of making holes with Copper nuts, bolts & washers for cable connections including hydrograpic insulators with nuts & bolts at both ends= 04 nos.(b) Air circuit Breaker Manual Drawout version capacity 630AICU=ICS=ICW (1s) =50KAsingle frame size with advance self power electronic protection units MP 4.10with LSI/LSIg+ neutral single frame size O/L + Over temperature protection+LCD Display with current metering +20 Trip History +20 Alarms+Logical selectivity, long time delay protection against overloads Ir from 0.2Ir to 1 x In (Step 1A)- OFF, long delay protection operationtime tr=40ms+30s (step 40ms),short time delay protection against short circuit ISd = from 1.5 Ir to 10 Ir- OFF (step 1A), short time delay protection operation time (t =K, I2t=K) tsd 40 ms + 1s (step 40 ms), Instaneous protection against very high short circuits li from2 to 15 in - OFF(step -1A), Earth fault currentlg from 0.2 + In - OFF (step 0.1 In), Time delay on earth fault tripping (t=K, I2t=K) tg from 80 ms + 1S (step 40 ms) Neutral protection IN=50%-100%-150%-200% - OFF, In built temperature protection, Rotatable terminals for Horizontal/Vertical Orientation fast operation , option to install various safety interlock.(c) Digital type flush mounted 3 phase VAF + PF meter with input voltage measurement range 50-500VAC (P-P), Aux supply 30-300 Volt AC/DC, CT secondary site selectable 1-5A, Accuracy Cl-1-0.5.(d) LED Neon indicator lamp (RYB) with holder,230/250 volts,AC - 01 set (set of three) |
| 31 | Out going:-(a) MCCB320 Amp, 4 Pole, 415 Volts, 36 KA rating with overload, short circuitfault protection 3 phase, Ics = 100% of Icu and shall have roto operative double break mechanism along total break time less than equal to 10 ms with Spreader terminal of both end side - 02 Nos. Make: Schneider Cat no - LV 540309/ Legrand Cat No: 422006/ Siemens, Cat: 3VA1332-4GE42-0AA0, ABB Cat No: 1SDA054478R1 L&T (LK) -CM94103OOQ1OG. |
| 32 | Supply ,fabrication, installation and testing of LT out door type factory made CPRI Approved , junction box of size 900mmX600mmX400mm (over all dimension) made out of 3.15 mm thick CRCA sheet dully supported with mild steel angle iron of size 40X40X5mm vertical frame and legs with mild steel flat iron 25X5 mm in horizontal sides of the frame with front and back side openable ,single hinged door / shutter with locking arrengement and powder coated finish both internal and external steel surfaces after necessary preparation of steel surfaces including providing PCC (1:3:6) type C2 foundation of size 0.80m X 0.6m X 0.90m depth (0.30m below ground level and 0.60m above ground level ) and connections of all outgoing / incomming existing cable of any size drawing / digging out cable from loops in trenches inclusive of necessary excavation and earthwork as required and relaying the cables including the following fitment accessories all complete as specified and directed.(a)Alluminium bus bar of size 50 mm X 6 mm X 400mm long wrapped with PVC sleeves with maintained the colour code and provision of making holes as required with nuts, bolts & washers for cable connections including hydrograpic insulators with nuts & bolts at both ends= 04 nos.(b)Enamelled iron danger notice plate of 1.60 mm thick mild steel sheet of size 200 mm X 150mm , white with letters , figures and conventional skull and bones in signal red and fixed with nuts and bolts on door / shutter of JB for LT -01 No. |
| 33 | Supply only epoxy type insulator for support of busbar grade 1100 volt as per existing size complete all as specified and directed. |
| 34 | Materialonly for control wiring of the panel with 1.5 sq mm multistranded, PVC insulated copper conductor 1100 Volt grade FRLS cable complete all as specified and directed. |
| 35 | Supply only LED phase indicator lamp colour RED/YELLOW/BLUE AC 220 Volt 50 Hz. complete all as specified and directed. |
| 36 | Supply only Digital Ampmeter of any range, flush mounting type of size96 mm x 96 mm (4”x4”) square dial 3 phase four wire system with selector switchcomplete all as specified and directed.. |
| 37 | Supply only Digital voltmeter of range (0-500) volts, flush mounting type of size96 mm x 96 mm (4”x4”) square dial 3 phase 4 wire system with selector switchcomplete all as specified and directed. |
| 38 | Supply only cast resin insulated type CT, Ratio 200/5Awith capable of withstanding momentary short circuitand symmetricalshort circuit for 01secondcomplete all as specified and directed. |
| 39 | Supply only cast resin insulated type CT, Ratio 250/5Awith capable of withstanding momentary short circuitand symmetricalshort circuit for 01second. complete all as specified and directed. |
| 40 | Supply only cast resin insulated type CT, Ratio 300/5Awith capable of withstanding momentary short circuitand symmetricalshort circuit for 01secondcomplete all as specified and directed. |
| 41 | Supply only copper bus bar any size (5x20, 10x20, 10x25, 10x40, 10x50,10x80) mmduly insulated with heat shrink busbar insulation sleevescomplete all as specified and directed. |
| 42 | Supply only aluminium bus bar any of any size duly insulated with heat shrink busbar insulation sleevescomplete all as specified and directed. |
| 43 | M&L in repair for replacement of MS sheet cover of LT panel board made out of any thick MS sheet as per required shape and size including necessary fabrication,welding and two coats of synthetic enamel painting over a coats of red oxide after proper preparation of steel surface complete and fixing accessories etc to match with existing panel surface complete all as specified and directed. |
| 44 | M&L for spray painting on existing steel surface of Panel/FPB/JB etc with two coats of synthetic enamel paint including one coat of red oxide on rusted area after proper cleaning and prepration of old painted surfaces steel / Iron of any description with spray machine complete all as specified and directed.Note:- Painting of panels / feeder filler boxes shall be carried out in different colour of paints as required at site and as directed). |
| 45 | Excavating and relaying of cables loops near the poles, panels, distribution box, cutting the damages/burnt parts of cable and reconnecting in the same position with aluminium thimbles/lugs of same size of cable, nuts bolts and washer (made of stainless steel) with proper insulation and cable sleeves etc complete all as specified and directed.Note : (i) Cost of nuts, bolts, washer, aluminium thimble/Lugs, insulation tape shall be deemed to be included in the quoted rate.(ii) Cost of sleeves measured and paid separately on relevant items of the schedule. |
| 46 | S& Fin repair of copper spreader terminal Kitsuitable for MCCB capacity 63 to100 Amp of any make and as per existing MCCB at site complete all asspecified anddirected. |
| 47 | S& Fin repair of copper spreader terminal Kitsuitable for MCCB capacity 125- 200 Amp of any make and as per existing MCCB at site complete all asspecified anddirected. |
| 48 | S& Fin repair of copper spreader terminal Kitsuitable for MCCB capacity 200 to 320 Amp of any make and as per existing MCCB at site complete all asspecified anddirected. |
| 49 | S& Fin repair of copper spreader terminal Kitsuitable for MCCB capacity 400 Amp of any make and as per existing MCCB at site complete all asspecified anddirected. |
| 50 | M&L forPainting ofsteel polewith cross arms, clamp of any length and shape for LT overhead line with single coat of aluminium paint including preparation of the existing surface including marking pole numbers in a 20 cm dia black circle with white letter painting of 3 Nos black & 02 Nos yellow bands width 30 cm by fluorescent paint in alternate layers upto 1.5 mtr heightabove theP.C.Ccopingandtwocoatofaluminiumpaintbeyond 1.5 meterheightcomplete all as specified and directed. |
| 51 | Relaying of old serviceablebrick as in cable protection completeall as specified and directed. |
| 52 | Taking out old unserviceable under ground cable of any size and any position from trenches, floors and wall and segrate the serviceable portion cable for reuse complete all as specified and directed. |
| 53 | Labour for drillinghole under the road with the help of bocki / by manual or by machinefor crossing GI tubingof any size 100 mm pipefor cable protection complete all as specified and directed. |
| 54 | Relaying of serviceable cable of any size retrieved here-in-above item after detecting the fault and making straight through jointing kit of 1100volt grade complete all as specified and directed.Note:-Necessary excavation,returning filling, removal of soil and straight through joint shall be measured and paid separately under respective item of this schedule. |
| 55 | Supply,laying & fixing double wall corrugated (DWC) pipes ofsize 63 mm outer dia and 50mm inner diamade of high density polythyline (HDPE) conforming to IS 16205(Part-24) in place of old Bricks including all accessories i.e. all type of joints, Sockets, Elbows, bends and End caps etc.. completeallas specified and directed.Make:- Supreme, Astral and Apollo or any other make approved by eastern command. |
| 56 | Supply and fixing cable jointing kit for 1.1 KV grade cable for straight through joint complete with jointing material heat shrink type and accessories suitable for 3½core XLPE, armoured, Aluminium conductor cable of size 150 to 185 sqmm complete all as specified and as directed. |
| 57 | Supply and fixing cable jointing kit for 1.1 KV grade cable for straight through joint complete with jointing material heat shrink type and accessories suitable for 3½core XLPE, armoured, Aluminium conductor cable of size 70 to 120sqmm complete all as specified and as directed. |
| 58 | Supply and fixing cable jointing kit for 1.1 KV grade cable for straight through joint complete with jointing material heat shrink type and accessories suitable for 3½core XLPE, armoured, Aluminium conductor cable of size 25 to 50 sqmm complete all as specified and as directed. |
| 59 | Supply and fixing cable jointing kit for 1.1 KV grade cable for straight through joint complete with jointing material heat shrink type and accessories suitable for 4core XLPE, armoured, Aluminium conductor cable of size 6 to 16 sqmm complete all as specified and as directed. |
| 60 | Supply and fixing Aluminium Lugs long barrel size 16 Sq mm all as specified and directed |
| 61 | Supply and fixing Aluminium Lugs long barrel size 35 Sq mm all as specified and directed |
| 62 | Supply and fixing Aluminium Lugs long barrel size 50 Sq mm all as specified and directed |
| 63 | Supply and fixing Aluminium Lugs long barrel size 95 Sq mm all as specified and directed |
| 64 | M&L for taking out and shifting the allLT Panel , Feeder Pillar Box, Junction Box not in proper ground space for workingand providing PCC (1:3:6) type C2 foundation of size 0.80m X 0.6m X 0.90m depth (0.30m below ground level and 0.60m above ground level ) and connections of all outgoing / incomming existing cable of any size drawing / digging out cable from loops in trenches inclusive of necessary excavation and earthwork as required and relaying the cables and commissioning the panelallasspecified and as directed.Note : No extra cost for PCC, Excavation of Looping cable should be paid to the contractor separately. |
| 65 | M&Lfor precast cement concrete RCC (1:2:4 type B-1 route indicator of size 150x150x600mm with 8 mmdia steel einforcement @ 100 c/cboth ways duly engraved \" LT CABLE/LT JOINT /FEEDER NO \" with two coats synthetic enamel paint first quality fixd with (PCC 1:3:6) below ground level of size 30x30x300mm complete all as specified and directed.Note : Quoted unit rate is deemed to be included the necessary cost of excavation, returning filling and removal etc. |
| 66 | Material and labour for Servicing and maintenance of Servo stablizerindoor/outdoortype and any of capacityatsite under the AOR of GE Bengdubi in any position(except major repair /rewinding),including partial decanning of stablizeroil, opening of top cover, disconnecting of internal connections of bushes,etc, replacement of unserviceable items i.e motors, transformer, control unit , brush carbon , top cover gasket of rubber cork sheet, tap changer, replace the burn out relay, etc complete all as specifed and as directed.Note :- (i) All tools and plant including magger, oil testing machine,and unloading all equipements such as crane/Hydra, chain pulley will be arranged by the contractor and No extra charges shall be paid to the contractor.(ii) Contractor shall deposit / Procure all the material in advance to avoid any late night fault/ after market hours / non availability of material in market. The elect supply shall be restore within 6 hours from the time of intimitation in day or night in the stn, failing this a panelty of Rs 3000/- per days /per complaint will be imposed on the contractor from contractor dues.(iii) Stablizer will be provided as and when repair work required/fault occured during the complete period of contract. Visit and repair charges of electrician and helper are included in the quoted rate. No extra charges shall be paid to the contractor.(iv) Strip opening of servo voltage stablizerfor detecting fault shall be included in the quoted rate. No extra amount shall be paid to the contractor. |
| 67 | Note:-(i) Minor Gasket, rubber washer, Copper / Aluminum thimble, nuts, bolts and washer for any size of stabliserwill be included in the quoted rate . No extra amount shall be paid to the contractor for the same.(ii) Stud/spindle, stabliseroil, dehydration ofoil and insulator and other major items shall be measured and paid seperately. |
| 68 | Supply only RollerCarbon brush as per sample at existing site all as specified and directed please |
| 69 | Supply only reversible synchronising single phase motor low speed - instant start stop ,High torque -10 Kg cm capacity 0.008 HP, input voltage240V 50 Hz 250 mAas per sample at existing site all as specified and directed please |
| 70 | Supply onlyvariac dimmer for 3 ph oil cooled servo voltage stabliser as per sample at existing site all as specified and directed. |
| 71 | Supply onlyE.C Grade DPC/super enamelled copper winding wire and rewinding for made out of buck boost transformerof 3 ph oil cooled servo voltage stablizer as per existing number of turns, gauge, insulation value matching with OEM designed complete all as specified and directed. |
| 72 | Supply onlymicro controller based fully automatic digital type servo motor operated line voltage corrector as per sample at existing site all as specified and directed. |
| 73 | Supply onyPorcelain Bushing including brass stud and nutas per existing size suitable for servo voltage stablizer anycapacity all as specified and directed. |
| 74 | Material and labour for toping up of the servo voltage stablizeroil withnew transformer Oil having dielectric strength not less than 50 KV complete all as specifed and as directed. Make - Power link /Savita/Transol |
| 75 | Taking down carefully copper / aluminium point wiring (light, fan, switch,socket or power, Bell & Two way point) complete with fitting such asswitches, sockets, ceiling rose,sketch light fittings etc, and making good the disturbed surface ofwalls and floors etc complete all as specified and directed. |
| 76 | Taking down carefully main switches DB\"s/ MCB DB\"s and making good the disturbed surfaces of wallsetc complete all as specified and directed. |
| 77 | Taking down carefully copper / aluminium sub mainwiring including teak wood batten / conduit and making good the disturbed surface of walls directed. |
| 78 | Material and labour for point wiring with 1.50 Sqmm single core PVC insulated, unsheathed cable FRLSH 1100 volts grade with multi stranded copper conductor drawn through and incuding medium grade PVC conduit with all accessories such as elbow, tee, bend etc, ISI marked,concealed on wall/ceiling and incuding provision of 1.50 Sqmm single core PVC insulated, unsheathed cable FRLSH 1100 volts grade with multi stranded copper conductor green colour as earth continuity conductor and connected to common earth dolly with suitable size of lugs, including or modular metal flush box for fixing modular switch, socket etc and mild steel sunken boxes made out of 1.6 mm thick mild steel sheet metal with earth dolly and coated of red oxide primer both internally and externally including provision of new 3 mm thick plastic laminated sheet top cover for housing the switches, socket outlets, fan regulators etc with brass screws and brass washers and making good the disturbed surfaces as per existing for one light point controlled by one way switch complete all as specified and directed. Note :- Switches, socket and fan regulators and modular box inner and outer cover plate to be measured and paid separately. |
| 79 | All as per item no 75.00 above but one bell point controlled by one bell Push |
| 80 | All as per item no 75.00 above but one 5 Amps socket out let point controlled by one switch on same board with other switches. |
| 81 | All as per item no 75.00 above but one 5 Amps socket out let point on independent board controlled by one switch. |
| 82 | All as per item no 75.00 above but one light point controlled by one, two way switch 5 Amps |
| 83 | All as per item No 75.00 above but wiring with 2.5 sq mm single core copper conductor for one socket out let 15/16 amps point on the independent board. |
| 84 | Material and labour for point wiring with 1.50 Sqmm single core PVC insulated, unsheathed cable FRLSH 1100 volts grade with multi stranded copper conductor drawn through and non metallic rigid PVC casing caping double lock system with all accessories such as elbow, tee, bend etc, ISI marked on wall/ceiling and incuding provision of 1.50 Sqmm single core PVC insulated, unsheathed cable FRLSH 1100 volts grade with multi stranded copper conductor green colour as earth continuity conductor and connected to common earth dolly with suitable size of lugs, including mild steel sunken boxes made out of 1.6 mm thick mild steel sheet metal with earth dolly and coated of red oxide primer both internally and externally including provision of new 3 mm thick plastic laminated sheet top cover for housing the switches, socket outlets, fan regulators etc with brass screws and brass washers and making good the disturbed surfaces as per existing for one light point controlled by one way switch complete all as specified and directed. Note :- Switches, socket and fan regulators to be measured and paid separately. |
| 85 | All as per item no 81.00 above but one bell point controlled by one bell Push |
| 86 | All as per item no 81.00 above but one 5 Amps socket out let point controlled by one switch on same board with other switches. |
| 87 | All as per item no 81.00 above but one 5 Amps socket out let point on independent board controlled by one switch. |
| 88 | All as per item No 81.00 above but wiring with 2.5 sq mm single core copper conductor for one socket out let 15/16 amps point on the independent board. |
| 89 | Material and labour for point wiring with 1.50 Sqmm single core PVC insulated, unsheathed cable FRLSH 1100 volts grade with multi stranded copper conductor drawn through in existing conduit on wall/ceiling and incuding provision of 1.50 Sqmm single core PVC insulated, unsheathed cable FRLSH 1100 volts grade with multi stranded copper conductor green colour as earth continuity conductor and connected to common earth dolly with suitable size of lugs, including mild steel sunken boxes made out of 1.6 mm thick mild steel sheet metal with earth dolly and coated of red oxide primer both internally and externally including provision of new 3 mm thick plastic laminated sheet top cover for housing the switches, socket outlets, fan regulators etc with brass screws and brass washers and making good the disturbed surfaces as per existing for one light point controlled by one way switch complete all as specified and directed. Note :- Switches, socket and fan regulators to be measured and paid separately. |
| 90 | All as per item no 86.00 above but one bell point controlled by one bell Push |
| 91 | All as per item no 86.00 above but one 5 Amps socket out let point on independent board controlled by one switch. |
| 92 | All as per item No 86.00 above but wiring with 2.5 sq mm single core copper conductor for one socket out let 15/16 amps point on the independent board. |
| 93 | M&L for concealed flame-proof point wiring FRLSH PVC insulated unsheathed single core multi-standard copper conductor cable 1100 volt gade of 1.5sqmm drawn through and including (medium grade) stove enamelled steel conduit in concealed of FRLS PVC insulted unshelathed single core multi standard copper conductor cable for earth continuity wire, connected to earth dolly and to be terminated in control Gear box/Flame proof switch wih and including flame proof junction box as per requirement including testing on completion compete including cutting chases for concealed conduct pinning in making good to facing and pointing in using cement mortar and making good disturbed surfaces complete all as specified and as directed. |
| 94 | Supply and fixing switch piano flush button single pole one way 5 amps, AC 240 Volts complete all as specified and directed. |
| 95 | Supply and fixing in repair switch piano flush button single pole one way 5 amps, AC 240 Volts complete all as specified and directed. |
| 96 | Supply and fixing socket outlet flush type 5 Amps, 5 pin, AC 240 Volts complete all as specified and directed. |
| 97 | Supply and fixing in repair socket outlet flush type 5 Amps, 5 pin, AC 240 Volts complete all as specified and directed. |
| 98 | Supply and fixing switch piano flush button single pole one way 15 Amps AC 240 volt complete all as specified and directed. |
| 99 | Supply and fixing in repair switch piano flush button single pole one way 15 Amps AC 240 volt complete all as specified and directed. |
| 100 | Supply and fixing socket outlet flush type multipurpose 2 in1, 3 pin 5 and 15 Amps, AC 240 volts complete all as specified and directed. |
| 101 | Supply and fixing in repair socket outlet flush type multipurpose 2 in1, 3 pin 5 and 15 Amps, AC 240 volts complete all as specified and directed. |
| 102 | Supply and fixing bell push single pole, 6 Amps, AC 240 Volts, flush type complete all as specified and directed. |
| 103 | Supply and fixing in repair bell push single pole, 6 Amps, AC 240 Volts, flush type complete all as specified and directed. |
| 104 | Supply and fixing celing rose surface bakelite 63.5 mm dia three terminal complete all as specified and directed. |
| 105 | Supply and fixing in repair celing rose surface bakelite 63.5 mm dia three terminal complete all as specified and directed. |
| 106 | Supply and fixing electronic Fan regulator 450 watt 2 module, with 5 step type regulator complete all as specified and directed. |
| 107 | Supply and fixing in repair for electronic Fan regulator 450 watt 2 module, with 5 step type regulator complete all as specified and directed. |
| 108 | Supply and fixing ding dong Bell, AC 240 Volts,single pole complete all as specified and directed. |
| 109 | Supply and fixing Bell multi music typeAC 240 Volts, single pole complete all as specified and directed. |
| 110 | Refixing paino switch of any capacity 5 /15 amps obtained from respective item of BOQ. |
| 111 | Refixing socket 5 amps or 15 amps capcaity obtained from respective item of BOQ. |
| 112 | Supply and Fixing Flame proof rotary type switch with termination box in LM6, 16A single pole 250V AC Complete all as specified and as Directed |
| 113 | Supply and fixing in repair PVC rectangular block for mountingswitches, sockets ,fan regulatoretc with 3 mm thick plastic laminated sheet cover of size 350 x 300 x 50 mm complete all as specified and directed. |
| 114 | All as per item no 110.00 above but of size 250 x 200 x 50 mm. |
| 115 | All as per item no 110.00 above but of size 200 x 150 x 50 mm. |
| 116 | All as per item no 110.00 above but of size 175 x 100 x 50 mm. |
| 117 | All as per item no 110.00 above but of size100 x 100 x 50 mm size. |
| 118 | Supply and fixing in repair pressed steel terminal rectangular sunken boxes made out of 1.6 mm thick mild steel sheet metal with earth dolly for mounting, switches, sockets, fan regulator etc including 3.00 mm thick plastic laminated sheet cover of suitable size for MS box size of 250 x 300 x 50 mm with brass screws and brass washers complete all as specified and directed. |
| 119 | All as per item no 115.00 above but of MS box size of 200mm X 250 mm |
| 120 | All as per item no 115.00 above but of MS box size of 200mm X 150 mm |
| 121 | All as per item no 115.00 above but of MS box size of150mm X 100 mm |
| 122 | All as per item no 115.00 above but of MS box size of 100mm X 100 mm |
| 123 | Supply and fixing in repair plastic laminated bakelite sheet cover of Hylam brand 3.00 mm thick including cutting holes for switches, sockets etc as per requirement including fixing with brass machine screws and washer for size 275 mm X 325 mm complete all as specifed and directed. |
| 124 | All as per item no 120.00 above but of size225 mm X 275 mm |
| 125 | All as per item no 120.00 above but of size 225 mm X 175 mm |
| 126 | All as per item no 120.00 above but of size175 mm X 125 mm |
| 127 | All as per item no 120.00 above but of size125 mm X 125 mm |
| 128 | Supply and fixing double door TPN DBs 4 wayof powder coated DB\"s suitable for MCB\"s fitted with bus bar,Neutral link,Earth bar and Din ral & DB\"s will be fitted concealed in wall / surface as per site required complete all as specified and directed. |
| 129 | Supply and fixingdouble door SPN DBs 12 wayof powder coated DB\"s suitable for MCB\"s fitted with bus bar,Neutral link,Earth bar and Din ral as per existing finishing complete all as specified and directed. |
| 130 | Supply and fixingdouble door SPN DBs 8 wayof powder coated DB\"s suitable for MCB\"s fitted with bus bar,Neutral link,Earth bar and Din ral as per existing finishing complete all as specified and directed. |
| 131 | Supply and fixing double door SPN DBs 4wayof powder coated DB\"s suitable for MCB\"s fitted with bus bar,Neutral link,Earth bar and Din ral as per existing finishing complete all as specified and directed. |
| 132 | Supply and fixing single door SPN DBs 2 wayof powder coated DB\"s suitable for MCB\"s fitted with bus bar,Neutral link,Earth bar and Din ral as per existing finishing complete all as specified and directed. |
| 133 | Supply and fixing MCB SPN 5 to 40 amps 10 KA ,C-series including connection with suitable size aluminium / copper lugs complete all as specified and directed. |
| 134 | Supply and fixingMCB SPN 40 to 63 amps 10 KA ,C-seriesincluding connection with suitable size aluminium / copper lugs complete all as specified and directed. |
| 135 | Supply and fixingMCB SP 240 volts 5 to 32 Amps, 10 KA breaking capacity,\"C\" type including connection with suitable size aluminium / copper lugs complete all as specified and directed. |
| 136 | Supply and fixing MCB TPN 50 to 63 amps 10 KA ,C-seriesincluding connection with suitable size aluminium / copper lugs complete all as specified and directed. |
| 137 | Refixing MCB TPN/SPN/SP any size, capacity obtained from respective item of BOQ. |
| 138 | Supply and fixing LED tube light batten box type with decorative end caps suitable single tube 1x 18/20 watt T8 lamps type complete with both end bi-pin holder and all accessories internally pre wired and fixed to wall/ceiling incl fittings accessories and connecting with all accessories internally pre wired and incl connecting up with twin core twisted flexible copper conductor cable suitable size all as specified. |
| 139 | supply and fixing LED tube rod 18/20 watt230 volt T8 type complete with electric electronic driver incl fittings accessories and connecting with all accessories internally pre wired and incl connecting up with twin core twisted flexible copper conductor cable suitable size all as specified. |
| 140 | Supply and fixing in repair Energy Savings Long Life 15 Watt 230 Volts50 Hz, IP20 rating recessed mounting downlight withaluminium housing and heat sink for better thermal performance and morden and minimalist design with flushed diffuser and as per site requirement ceiling cutout fitting for cool/warm or natural white light options as required including electronic driver of suitable capacity with PF>0.9 complete all as specified and directed. |
| 141 | Supply and fixing in repair Energy Savings Long Life 12 Watt 230 Volts50 Hz, IP20 rating recessed mounting downlight withaluminium housing and heat sink for better thermal performance and morden and minimalist design with flushed diffuser and as per site requirement ceiling cutout fitting for cool/warm or natural white light options as required including electronic driver of suitable capacity with PF>0.9 complete all as specified and directed. |
| 142 | Supply and fixing in repair Energy Savings Long Life 06 Watt 230 Volts50 Hz, IP20 rating recessed mounting downlight withaluminium housing and heat sink for better thermal performance and morden and minimalist design with flushed diffuser and as per site requirement ceiling cutout fitting for cool/warm or natural white light options as required including electronic driver of suitable capacity with PF>0.9 complete all as specified and directed. |
| 143 | S&F recessed mounting fitting 1 x 36/42 watt ultra modern design Natural white/ Warm white architectural LED luminaire (2X2) feet which provides soft-light and glare free symmetrical illumination suitable for Armstrong / Grid Ceiling including LED driver and 36/42 watt LED for cool/warm or natural white light options as required including electronic driver of suitable capacity with PF>0.9 complete all as specified and directed. |
| 144 | S&F LED light fitting 1 x 16 Watt Flame Proof,CMRI Certified Recommended For Gas/ Vapour group of IIA & IIIB, Zone 1 & 2 and IP 65 protection with die cast aluminium hosing with heat resistant toughened glass with LED light fixures driver , holders,connector etc, complete with all accessories prewired and including connecting up with three core flexible copper conductor cable with suitable size complete all as specified and directed. |
| 145 | S & F in replacement Building security LED light luminaire 1X25 W, pressure die cast housing with toghned glass, 240V, efficacy Min 110 Lm/Watt, IP-66, 5 KV external SPD , THD<10%, PF>0.95, CCT-5700K, High power SMD LEDs with LDR sensor working 10 Lm visibility for automatic ON/OFF operation and including cable for connection from celling rose with 1.5 Sqmm 3 CorePVC insulated stranded copper conductor (FRLS) cable including GI bracket medium grade bent to shape etc all as specified and directed. |
| 146 | Supply and fixing LED Batten light Aluminium Housing 18/20 watt230 volt T8 type complete with electric electronic driver incl fittings accessories and connecting with all accessories internally pre wired and incl connecting up with twin core twisted flexible copper conductor cable suitable size all as specified. |
| 147 | Refixing LED tube light fittings any type, wattage and any size obtained from respective item of BOQ. |
| 148 | Supply and fixing LED batten tube light fitting 1x 10 watt 230 voltwall/ ceiling mounted luminaire with polycarbonate hoiusing and integrated electronic driver with all accessories internally pre wired and incl connecting up with twin core twisted flexible copper conductor cable suitable size all as specified. |
| 149 | Supply and fixing LED bulk head 10 watt fittings environmental friendly ultra modern energy saving surface mounted decorataive bulk head fitting with driver and prewired and necessary electric connection with PVC insulated twin twisted flexible copper wire of size 0.75 Sqmm complete all as specified and directed. |
| 150 | S&F in replacement Lamp holder , PVC / Polycarbonate type with back plate suitable for B22 lamp including LED Bulb 9W complete all as specified anddirected. |
| 151 | M&L for Sub main wiring two run single core PVC insulated unsheathed cable FRLSH 1100 volts grade, 6.00 Sqmm size with multistranded copper conductor, drawn in but excluding non metallic rigid PVC conduit including one run of 4.00 Sqmm single core PVC insulated, unsheathed cable FRLSH 1100 volts grade with multi stranded copper conductor green colour as earth continuity conductor cable connected to earth dolly complete all as specifed and directed. |
| 152 | All as peritem No 148.00 but with two single core 4.0 Sqmm sizewith 2.5 Sqmm cable as earth conductor complete. |
| 153 | All as peritem No 148.00 but with two single core 2.5 Sqmm sizewith 2.5 Sqmm cable as earth conductor complete. |
| 154 | All as peritem No 148.00 but with two single core 1.5 Sqmm sizewith 1.5 Sqmm cable as earth conductor complete. |
| 155 | M&Lfor Rigid non metallic PVC conduitISI marked, medium grade, inclusive of all fitting such as tees,bends. Junction boxes, elbows saddles. Pipe hooks,couples and lock outs etc 25 mm external dia, fixed on surface mounted complete and making good disturbedsurfaces in repairs all directed. |
| 156 | M&Lfor Rigid non metallic PVC casing capingISI marked, medium grade,not less than 25 mm base size inclusive of all fitting such as tees,bends. Junction boxes, elbows saddleshooks,couples and lock outs etc fixed on surface mounted complete and making good disturbedsurfaces in repairs all directed. |
| 157 | Supply & fixing Sheet metal earth plug, socket, single pole and neutral with single pole MCB 32 Amps 240 volts fixed in repairs complete. |
| 158 | Supply and fixing ofEarthing to building with galvanised steel earth plate electrode 60cm x 60cm x 6mm thick, buried directly in ground (earth pit not less than 2.25m below normal ground level) with top edge of earth plate not less than 1.5m below normal ground level connected to galvanised earth strip 25x4mm by means of bolts, nut, check nuts and washers of galvanized iron or steel all as shown in electrical plate No.3 of MES Schedule pt-I 2009, GI earth lead strip protected by GI pipe 40 mm dia light grade and connected to earth test point includingexcavation in any type of soil,returning filling, disposal of soil, providing charcoal dust and common salt upto top edge of earth plate, construction of PCC pit with RCC cover, funnel, watering pipe of 20mm dia GI light grade and provision of earth test point including testing on completion all as specified and directed. |
| 159 | (Note : The Scope of Work contained in \"Sch of Credit\" amounting to Rs. 1,32,117.00 (refer Sch of credit). The Quoted sum shall be arrived at after deducting the amount of “Sch of Credit” from the total amount of the ‘BoQ’ |
