|
| 1 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises to outside MD Land. |
| 2 | M & L for precast cement concretesolid building blocks or slabs 10cm thick with plain or interlocking joints with PCCtype C1 1:3:6using 20mm graded stone aggregatesetting in mortar 1:4 in walls, complete all as specified and directed. |
| 3 | M& L for Pre-cast cement concrete block masonry with type C1 (1:3:6) using 20 mm graded stone aggregate solid blocks, exc. 10 cm in width and setting in cement mortar 1:6,complete all as specified and as directed. |
| 4 | M & L for Rendering 10 mm thick on fair faces of brick work or concrete wall surfaces in CM 1:6 surface finished even & smooth without using extra cement complete all as specified. |
| 5 | M & L for Rendering 15 mm thick on fair faces of brick work or concrete surfaces in CM 1:4 finished even & smooth without using extra cement with using WPCcomplete all as specified. (WPC shall be measured and paid separately). |
| 6 | Supply only integral water proofing liquidcomplete all as specified and as directed. |
| 7 | M&L for applying two coats of Oil bound distemper on walls including reparation of new plastered surfaces over a coat of primer complete all as specified and as directed. |
| 8 | Preparing newly plastered surfaces of walls and applying two coats of cement based paint over a coat of primer complete all as specified and as directed. |
| 9 | M&L for Precast reinforced cement concrete 1:2:4 mix, type B-1 using 20 mm graded stone aggregate as in slabs supported on walls, as in platforms, shelves etc all as specified and directed. |
| 10 | M&L for Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams,etc.complete all as specified and as directed. |
| 11 | M&L for Mild steelTMT bars 10mm dia and over cut to length bent to shape required including crancking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia all as specified and directed. |
| 12 | M&L for 20mm thick Granite(of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills,cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match withshade incl screed bed or bedding layer of mortar 20mm thick for laying floor finishesin CM (1:4) etc complete all as specified. |
| 13 | M & L for rounding to edges of stone slabs one edge, such as in steps, cooking platforms, and other similar situations |
| 14 | Supplying and laying of 32 mm dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings in walls/trenches including cutting holes in walls and making good with CM (1:3) where required and taking down old tubing of any description complete all as specified and as directed. |
| 15 | Supplying and laying of 20 mm dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings in walls/trenchesincluding cutting holes in walls and making good with CM (1:3) where required and taking down old tubing of any description complete all as specified and as directed. |
| 16 | S&FRotational moulded PVC water storage tanks of 500 ltrs capacity (cylindrical vertical with closed top) , two layered, hoisted and fixed in position all as specified in SSR part – Iincluding tank nipple and lidcomplete all as specified and as directed. |
| 17 | S&F in repairs of Ball valve 20mm dia high pressure PTMT with epoxy coated aluminium rod & highdensity plastic ball screwed for iron pipe and fixed(Minimum wt. 210gms etc complete all as directed. |
| 18 | S&F 20mm Gun-metal, globe or gate valves, with iron wheel head, screwed both endssuitable for CPVC pipe incuding connecting socket all as specified and directed. |
| 19 | S&F Stainless steel sink, 1.00mm thick for kitchen or laboratory, with plug, waste pipe, washers, including cantilever cast iron brackets, connecting union etc., overall size 495mm x 420mm with bowl size 410mm x 330mm x 160mm→ |
| 20 | S&F Waste coupling of32 mm PTMT for glazed ware basins/urinals with long screwed shanks and fly-nuts etc complete all as specified and directed. |
| 21 | M & L infor high density pipe 40 mm dia (HDPE)pressure rating 6 Kg / Sqcm fixed to wall and floors etcall as specified and as directed. |
| 22 | Cutting holes into or through brick walls not exc 150 sqcm built in cement mortarand stone walls and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-l as required |
| 23 | Demolition of Plain cement concrete (un reinforced)in ground floors and pavings not exceeding 15 cm thickness (below or above ground level) complete all as specified and directed. |
| 24 | M& L for 75 mm thick Plain Cement concrete Type D2 1:4:8 (40 mm graded Aggregate) as in sub base flooring complete all as specified and as directed. |
| 25 | M&L 25 mm thick plain Cementconcrete type B-1, 1:2:4 (20mm graded aggregate) as in floor finish concrete complete all as specified and as directed. |
| 26 | M & Lfor coloured Non-skid ceramic tiles (square/rectangular) 7 to 8mm thick in floors, area of each tile exc.0.11 sqm but n.exc 0.18 sqm, set and jointed in Apoxy Grout 2 to 3 mm spacer and filled withwhite cement mixed with matching pigment over and including 20 mm thick screed bed in CM 1:6 all as specified. |
| 27 | M & L for rendering 10 mm thick in cement mortar 1 : 4 on brick or concrete surfaces as in screed bed all as specified and as directed. |
| 28 | Material and labour for Glazed ceramic coloured tiles in vertical surfaces 600X300X 7mm thick, set and jointed in neat cement slurry and pointed in white or colour cement to match with and including 10mm thick backing coat on vertical surfaces of wall in cement mortar 1:4 complete all as specified and as directed. |
| 29 | S & F in repair PVC (SWR) pipes of 75 mm dia single socketed in any length with rubber ring joints fixed to walls / floor completeall as specified and as directed |
| 30 | S & F in PVC (SWR) bend of 75 mm dia . |
| 31 | S&F in 75mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement all as specified and as directed |
| 32 | S&F in CP Bib taps 15 mm cast copper alloy fancy typewith crutch or butter fly handle screwed down screwed for iron pipe or for brass ferrule etc complete all as specified. |
| 33 | S&F of Structural Steel work as in main and cross beams, hip and jack rafters, purlins where connected to common rafters , vertical posts, etc fixed with angle cleats or other connecting plates, cleats etc. using ERW or induction butt welded tubes conforming to IS-1161-1998 grade St.-240or with holow structural steel sections conforming to IS 4923-1997 Grade St-240 all as specified and directed. |
| 34 | M&L for Mild steelTMT bars 10mm dia and over cut to length bent to shape required including crancking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia all as specified and directed. |
| 35 | M&L for preparation of new steel surfaces and applyingtwo coats of synthetic enamel paint over a coat of red oxide zinc crome primer on Surfaces of any description,over 10cm in width or girth, not otherwise described complete all as specified and as directed. |
| 36 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 50 x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardantand fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made |
| 37 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 35mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixingwith stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. (Note: stainless steel butt hinges and necessaryS Sscrews shall be paid separately) |
| 38 | S&F 100mm stainless steelbutt hinges, cold rolled medium weight |
| 39 | M & L forBrass handles, cast type, polished bright 150 mm long all as specified and directed |
| 40 | S & F of 125 mm Hasp and staple, mild steel, wire type, stove enamelled black, including bolt to hinge plate and fixed with screws complete all as specified. |
| 41 | S&F of 100mm Aluminum anodised barrel tower bolts of extruded section complete all as specified. |
| 42 | S&F Brass Locks cupboard grade I,size 50 mm brass 4 levers |
| 43 | M & L for FLAME PROOF surface sub-main wiring alongwith earth wire of size (2 x 4.0) sq. mm + (1 x 4.0) sq. mm earth wire, ISI marked, FRLS, PVC insulated, multi stranded, copper conductor, single core cable drawn through and including stove enamelled steel conduit of size not less than 25 mm dia with all fittings and accessories ISI marked for conduits & sinkings for Flame Proof Modular boxes (if any) & making good to walls, floors etc. complete all as specified & as directed. Make of cable : Havells/Polycab/Finolex. Make of Steel Conduit : ISI MarkedNOTE : 1) Two runs of PVC wire, one run of earth wire & one run of stove enamelled steel conduit will be measured as one length. 2) Modular Flame Proof metal flush boxes (if req) shall be measured & paid separately. 3) Cutting chases & making good the disturbed surfaces (if any) is deemed to be included in the unit quoted rates. 4) Cost of Metal clamps with fixing screws for fixing on walls/other surfaces etc. (if any) is deemed to be included in the unit quoted rates. |
| 44 | S&F single pole & neutral sheet metal enclosure with a two pin & earth plug & socket complete with one single pole MCB, \"C\" Curve, 10 KA, 20A all as specified & as directed to the entire satisfaction of the Engr-In-Charge.NOTE : Make of MCBs shall be same as the make of MCB DBs. |
| 45 | Supply, install, commissioning & testing of Flame Proof Split-type Air Conditioner Unit of capacity 2.0 TR or higher rating with & including the following technical specifications/certifications etc. incl electric connection complete all as specified and as directed. Cat/Part No : SAC/211 of Make : SUDHIR. |
| 46 | FLP WP AIR CONDITIONER UNIT :\"PRODUCT : CAT NO – SAC/211ENCLOSURE : FLAME PROOF ZONE-1 & 2 Gas Group II A, II B, II C (As per IS/IEC 60079-1 : 2014)PROTECTION : WEATHER PROOF IP – 66 AS PER IS / IEC 60529 : 2001 (Reaffirmed 2014)AREA & TEMP. CLASS : Ex db IIC T5 Gb EX tb / tc IIIC T85 C Db/Dc (ZONE 1 & 2)CERTIFICATION : CIMFR, BIS, PESOTEMP CLASS : T5MATERIAL : M.S. FABRICATED CASE / STAINLESS STEELFINISH : EPOXY POWDER COATED SHADE AS PER IS : 5EARTHING : 1 No INTERNAL & 2 No’s EXTERNALHARDWARE : STAINLESS STEEL\" |
| 47 | FLP WP ENCLOSURE FOR MOTOR :\"PRODUCT : CAT NO.: FAN / 140ENCLOSURE : FLAME PROOF ZONE-1 & 2 Gas Group II A, II B, II C (As per IS/IEC 60079-1 : 2014)PROTECTION : WEATHER PROOF IP – 66 AS PER IS / IEC 60529 : 2001 (Reaffirmed 2014)AREA & TEMP. CLASS : Ex db IIC T5 Gb EX tb / tc IIIC T85 C Db/Dc (ZONE 1 & 2)CERTIFICATION : CIMFR, BIS, PESOTEMP CLASS : T5MATERIAL : CAST IRON ( C.I )FINISH : EPOXY POWDER COATED SHADE AS PER IS : 5EARTHING : 1 No INTERNAL & 2 No’s EXTERNALHARDWARE : STAINLESS STEELGASKET : \"O\" RING ENDLESS GASKET NEOPRENE / SILICONNAME PLATE : SS NAME PLATE CUM WARNING PLATECABLE ENTRY : 1 No. M20 SIZE ENTRYTERMINAL : 2NO. 3/16” STUD TYPE TERMINAL OF SUDHIRMAKEMOTOR RATING : 920 RPM, SINGLE PHASE, 0.25HP\" |
| 48 | FLP WP ENCLOSURE FOR THERMOSTAT :\"PRODUCT : CAT NO.: JB/2C/2017ENCLOSURE : FLAME PROOF ZONE-1 & 2 Gas Group II A, II B, II C (As per IS/IEC 60079-1 : 2014)PROTECTION : WEATHER PROOF IP – 66 AS PER IS / IEC 60529 : 2001 (Reaffirmed 2014)AREA & TEMP. CLASS : Ex db IIC T5 Gb EX tb / tc IIIC T85 C Db/Dc (ZONE 1 & 2)CERTIFICATION : CIMFR, BIS, PESOTEMP CLASS : T6MATERIAL : CAST ALUMINIUM ALLOY LM6.FINISH : EPOXY POWDER COATED SHADE AS PER IS : 5EARTHING : 1 No INTERNAL & 2 No’s EXTERNALHARDWARE : STAINLESS STEELGASKET : \"O\" RING ENDLESS GASKET NEOPRENE / SILICONRANGE : THERMOSTATE RANGE FROM 12º TO 32ºNAME PLATE : SS NAME PLATE CUM WARNING PLATECABLE ENTRY : 2 No. M20 SIZE ENTRY.\" |
| 49 | FLP WP COMPRESSOR FOR TERMINAL UNIT :\"PRODUCT : CAT NO.: SAC/211ENCLOSURE : FLAME PROOF ZONE-1 & 2 Gas Group II A, II B, II C (As per IS/IEC 60079-1 : 2014)PROTECTION : WEATHER PROOF IP – 66 AS PER IS / IEC 60529 : 2001 (Reaffirmed 2014)AREA & TEMP. CLASS : Ex db IIC T5 Gb EX tb / tc IIIC T85 C Db/Dc (ZONE 1 & 2)CERTIFICATION : CIMFR, BIS, PESOTEMP CLASS : T5MATERIAL :CAST IRON (C.I) / M.S.FINISH : OUTSIDE BLACK EPOXY SPRAY AS PER IS: 5EARTHING : BRASS / SS SCREW OF M4.HARDWARE : STAINLESS STEELGASKET : \"O\" RING ENDLESS GASKET NEOPRENE / SILICONNAME PLATE : SS NAME PLATE CUM WARNING PLATECABLE ENTRY : 2 No. M20 SIZE ENTRY.COMPRESSOR RATING : 220-240V AC, 50 Hz., SINGLE PHASE SUPPLY.REFRIGERANT : ECO FRIENDLY GAS TYPE R 407 / 414 ETC.\" |
| 50 | FLP WP ENCLOSURE FOR CONTROL PANEL :\"PRODUCT : CAT NO.: CGB/2C/131ENCLOSURE : FLAME PROOF ZONE-1 & 2 Gas Group II A, II B, II C (As per IS/IEC 60079-1 : 2014)PROTECTION : WEATHER PROOF IP – 66 AS PER IS / IEC 60529 : 2001 (Reaffirmed 2014)AREA & TEMP. CLASS : Ex db IIC T5 Gb EX tb / tc IIIC T85 C Db/Dc (ZONE 1 & 2)CERTIFICATION : CIMFR, BIS, PESOTEMP CLASS : T6MATERIAL : CAST ALUMINIUM ALLOY LM6.FINISH : EPOXY POWDER COATED SHADE AS PER IS : 5EARTHING : 1 No INTERNAL & 2 No’s EXTERNALHARDWARE : STAINLESS STEELGASKET : ‘O’ RING ENDLESS GASKET NEOPRENE / SILICONMCB : 1 No. 32 AMP. DP MCBINDICATING LAMP : 1No. 240V AC LED TYPE LENS COLOUR \" RED \" .CAPACITOR : RUNNING CAPACITOR 40 mfdRELAY : PTC RELAYNAME PLATE : SS NAME PLATE CUM WARNING PLATECABLE ENTRY : 3 No. M20 SIZE ENTRY\" |
| 51 | Important Notes for Item Nos 4 & 5 :(i) Technical Specifications/particulars etc. of the Split ACs is to be obtained from OEM / Auth Supplier & is to be got approved from the GE & Engr-In-Charge before placing final order to the manufacturer.(ii) The Air Conditioner shall be initial filled / charged with refrigerant of specified quantity & the refrigerant to be used shall be Non-CFC type & as per the latest technology.(iii) Unit Quoted rates shall be deemed to be inclusive of the following connected items/job/work etc. :(a) Cost of copper refrigerant pipes for suction and discharge lines for connection of indoor to outdoor units of 1.5 ton split AC of standard size as per OEM recommendation with proper insulation including fixing arrangement with appropriate size MS clamps and jointing of pipe with brazing etc including all necessary items required complete all as specified and directed by Engr-in-Charge.(b) Cost of 3 core Weather cum Flame Proof proof copper cable (size as recommended by OEM), multistranded for electrical connection of Indoor & Outdoor Units. (c) Cost of PVC pipe 25mm dia high grade for ACs drain water suitable for outdoor mounting including connecting tees, bends, reducers etc. for leakage free jointing etc, including appropriate size PVC clamps and other required material for fixing on wall/cemented surfaces at heights as specified here in above complete all as specified and directed by Engineer-in-Charge.(d) Cost of making of holes etc. to existing wall/wooden panelling etc. using core cutting machine of suitable dia for the run of copper refrigerant tubings, connecting cables, outdoor units etc. and making good the distrubed surfaces/false ceilings etc. complete all as directed by Engr-in-Charge. |
| 52 | (e) Cost of MS angle iron frames of minimum size 50 mm x 50 mm x 6 mm suitable for fixing of Outdoor Units of Split AC\"s 1.5 Ton including fixing on wall/other surfaces etc. with necessary fixing arrangements like nuts, bolts, washers etc. as required on ground inclusive of one primer coat, one under coat and one finishing coat of synthetic enamel paint complete all as specified and directed by Engr-in-charge.(f) Cost of PCC 1:2:4, type B1 using 20 mm graded stone aggregate as in platform/plinth for embedding/holding of MS angle iron frames as cited here in above for fixing of Outdoor Units of Split AC\"s 1.5 Ton incl necessary formwork & applying two coats of white wash to exposed surfaces complete all as specified and directed by Engr-in-charge.(g) Cost of making good the disturbed surfaces incl matching to the existing/old surfaces.(h) Cost of neatly writing/marking MES Number on the body of Split AC Indoor Unit using stencil of size/dimensions complete all specified & as directed by the Engr-In-Charge. (j) Cost of 01 x Air Conditioning Changeover Timer, suitable for 2 x AC loads of 20 A each i.e. AC1-20A & AC2-20A, with Auto & Manual mode with interval/gap time of 30 Mins, 1 Hr, 2 Hr, 3 Hr, 4 Hr, DIN Channel mounting for easy operation incl electric connection with suitable sized single core copper wires/cables & testing complete all as specified & as directed to the entire satisfaction of the Engr-In-Charge.(k) Cost of provision of suitable shed for housing/covering of Outdoor Units of Flame Proof AC 2.0 TR, 5.0 KVA Voltage Stabilizers, Metal Plug & Sockets etc. complete all as specified & as directed to the entire satisfacton of the Engr-In-Charge.(iv) All the necessary OEM/Auth Supplier Test Certificates as per relevant IS/IEC incl the Guarantee/Warranty Certificates is to be submitted in Original to the Engr-In-Charge.(v) Anything missed out in the technical specifications but technically required for efficient working of the AC is deemed to be included in the unit quoted rates.(vi) The contractor/firm is required to visit the site prior to quoting of the subject items/ work so as to ascertain the actual ground requirements. Any further query at a later date shall not be entertained & responsibility of the same shall rest on the contractor/ firm.Supply, install, commissioning & testing of wall-mounted copper wound voltage stabilizer, ISI marked for automatic operation, single phase, naturally air cooled, indoor type & designed for I/P variation between 175 V to 250 V with Digital Voltmeter & O/P voltage stabilization at 230 V with accuracy of +/- 2.5%, with high & low voltage cut off & time delay & of capacity 5.0 KVA suitable for 2.0 TR Flame Proof Split AC incl electric connection complete all as specified and as directed. Make : APLAB/VENER-7/SINETRAC or Techno-commercially equivalent makes as approved by HQ CE Command. |
| 53 | NOTE :(i) Technical Specifications/particulars etc. of the Items is to be obtained from OEM / Auth Supplier & is to be got approved from the GE & Engr-In-Charge before placing final order to the manufacturer.(ii) Anything missed out in the technical specifications but technically required for efficient working of the AC is deemed to be included in the unit quoted rates.(iii) All the necessary OEM/Auth Supplier Test Certificates as per relevant IS/IEC incl the Guarantee/Warranty Certificates is to be submitted in Original to the Engr-In-Charge.(iv) The contractor/firm is required to visit the site prior to quoting of the subject items/ work so as to ascertain the actual ground requirements. Any further query at a later date shall not be entertained & responsibility of the same shall rest on the contractor/ firm. |
| 54 | Supply, install, commissioning & testing of wall-mounted copper wound voltage stabilizer, ISI marked for automatic operation, single phase, naturally air cooled, indoor type & designed for I/P variation between 175 V to 250 V with Digital Voltmeter & O/P voltage stabilization at 230 V with accuracy of +/- 2.5%, with high & low voltage cut off & time delay & of capacity 5.0 KVA suitable for 2.0 TR Flame Proof Split AC incl electric connection complete all as specified and as directed. Make : APLAB/VENER-7/SINETRAC or Techno-commercially equivalent makes as approved by HQ CE Command.NOTE :(i) Technical Specifications/particulars etc. of the Items is to be obtained from OEM / Auth Supplier & is to be got approved from the GE & Engr-In-Charge before placing final order to the manufacturer.(ii) Anything missed out in the technical specifications but technically required for efficient working of the AC is deemed to be included in the unit quoted rates.(iii) All the necessary OEM/Auth Supplier Test Certificates as per relevant IS/IEC incl the Guarantee/Warranty Certificates is to be submitted in Original to the Engr-In-Charge.(iv) The contractor/firm is required to visit the site prior to quoting of the subject items/ work so as to ascertain the actual ground requirements. Any further query at a later date shall not be entertained & responsibility of the same shall rest on the contractor/ firm. |
| 55 | S & F SPN DB, 8 Way, IP43, IK09, Metal double door type 240 volts fitted with busbar and blanking plates, neutral link and making good making good the disturbed surfaces with all other accessories including necessary connection all as specified and directed by Engr-in-Charge. Make-L&T/LEGRAND/SIEMENS/ABB. |
| 56 | S&F MCB, SPN, C-Series 240 Volts of capacity 6-32 Amps with breaking capacity 10 KA all as specified and dircted by Engr-in-Charge. Make-L&T/LEGRAND/SIEMENS/ABB. (2W+1S) |
| 57 | M&L for earthing complete with galvanized steel earth plate electrode 600 x 600 x 6.3 mm thick buried directly in ground (in vertical position) earth pit not less than 2.25 mtr below normal ground level with the top edge of the earth plate not less than 1.5 mtr (B.G.L.) and connected to galvanized iron wire 4 mm dia by means of bolts, nuts, check nuts, and washers of galvanized iron including PCC pit & cover with suitable handle including necessary excavation and earth work in any type of soil, 20 mm dia med grade galvanized steel tube for watering with one end fixed with funnel and wire mesh, 15 mm bore medium grade galvanized steel tubing for drawing earth lead GI strip protection & common salt, charcoal in alternate layers etc. complete all as shown in EP No 3 of SSR Part 1 and testing on completion complete. Make of GI Pipe : TATA/Jindal/PrakashNOTE : On completion of the complete work/job the Contr is to perform earth resistance tests for each earthing job in the presence of the Engr-In-Charge or his rep & submit test certificates duly signed & certified. If the test results are not satisfactory or not within the permissible limits of relevant Standards/IS then the job is to be redone without any extra cost to the Dept till the results are satisfactory. |
