|
| 1 | Demolition of unreinforced cement concrete in ground floors etc and paving n. exc 15cm thickness (below or above ground level) complete all as specified and directed by Engr-in-Charge. |
| 2 | M&L PCC (1:4:8) type-D2 (using 40mm graded crushed stone aggregate) as in mass conc. and sub base complete all as specified and directed by Engr-in-Chargre. |
| 3 | M&L for 25mm thick (1:2:4) Type-B-1 (using 12.5mm graded crushed stone aggregate) as in level course of flooring complete all as specified and directed by Engr-in-Chargre. |
| 4 | M&L non skid / anti skidceramic tiles coloured pattern as required of 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with and including dismantling of tiles and laid over15mm thick screed bed in CM (1:6) compete all as specified and directed by Engr-in-Charge |
| 5 | M&L non skid ceramic tiles coloured pattern as required of 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with and including dismantling of tiles and laid over15mm thick screed bed in CM (1:6)compete all as specified and directed by Engr-in-Charge |
| 6 | M&L non skidceramic tiles coloured pattern as required of 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with and includingdismantling of tiles and laid over15mm thick screed bed in CM (1:6)compete all as specified and directed by Engr-in-Charge |
| 7 | Description all as per ser item No.04, 05 & 06 above but on skirting over with and including 10mm thick backing coat in CM 1:4 withcomplete all as specified and directed by Engr-in-Charge. |
| 8 | M&L vitrified ceramic tiles coloured pattern as required 10mm thick (Square/rectangular) polished, area of each tiles not exceeding 0.36 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to matches with and includingdismantling of tiles and laid over15mm thick screed bed in CM 1:6 compete all as specified and directed by Engr-in-Charge |
| 9 | Description all as per ser item No 8 above but on skirting over with andincluding dismantling of tiles and laid over including 10mm thick backing coat in CM 1:4 complete all as specified and directed by Engr-in-Charge. |
| 10 | M&L forglazed ceramic coloured, designer & pattern (dark & light shade combination) tilesin 350x250x7 or450x350x7 or 450 x 300 x 7-8 mm thick on vertical surfaces such as dado etc set and jointed in neat cement slurry and pointed in white or colour cement to match over with and including 10mm thick backing coat in CM 1:4and dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by Engr-in-Charge |
| 11 | Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc. |
| 12 | M & L for 60mm thick confirming to IS 15658-2006 glossy interlocking tile of M-30 mix laid over dry sandcushioning,filling of joints with sand & compactionafter filling of joints and edges shall be secured with PCC 1:2:4 type B-0 complete all as specified and as directed. (Note : Supplying and spreadingfor sandcushioning shall be measured and paid separately) . |
| 13 | Supply and spreading sand filling under floors or interlocking tile or in foundation including watering and consolidation complete all as specified and directed |
| 14 | M&L for Machine cut kota stone slab flooring 18-20mm thick of size not less than .034 Sqm of each slab over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing with and including 20mm thick screed bed or bedding in cement mortar 1:6 complete all as specified and directed by Engr-in-Charge. |
| 15 | M&L for Kota stone slab 18-20mm thick in riser of bricks steps & riser of staircase , skirting, dado and pillar laid over cement screed and jointed with pigment to match the shade of the slab including rubbing and polishing with & including backing coat in 10mm thick CM (1:4) to receive Kota Stone complete all as specified and directed by Engr-in-Charge.. |
| 16 | M&L Granite (of any type) tiles, 18-20 mm thick machine cutlaid over cement screedand jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of the granite stone including cutting and polishingwith and including 20mm thick screed bed or bedding in cement mortar 1:4and including dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premisescomplete all as specified and directed by Engr-in-Charge. |
| 17 | M&L for rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and directed by Engr-in-Charge. |
| 18 | Dismantling plain or corrugated steel sheeting, any gauge, thickness, including nainital or similar roof coverings complete all as specified and directed. |
| 19 | S&F 0.63 galvanised, corrugated mild steel sheeting with two corrugation side lap fixed with J or L type hooks in roofs, walls etc. with grade of zinc coating 275 complete all as specified and directed. |
| 20 | S&F 1.00 mm thick plain galvanised,mild steel sheeting, with grade of zinc coating 275 as in ridges, hips vally gutters drip and straight flashing (length and grith as fixed) complete all as specified and directed. |
| 21 | Preparing new zinc (or galvanised) and steelsurfaces to receive painting, by coating with mordant solution including washing and cleaning, etc. iron surfacesas in roofings exceeding 10 cms width or girth and applying two coats of synthetic enamel paintoveronecoat of red oxide zinc chromeprimer, all as specified. |
| 22 | S&F for pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550mpa as in roof covering /cladding to wall, fixed with self tapping screws complete with and including dismantling corrugated steel sheeting, any gauge, thickness, including nainital or similar roof coverings complete all as specified and directed.completed all as specified and directed by Engr-in-Charge. |
| 23 | S&F for pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550mpa as in roof covering /cladding to wall, fixed with self tapping screws as in ridge,eaves boards, hips, velly gutter drip and straight flushing of reuired machine moulded shape and size complete with and including dismantling plain steel sheeting, any gauge, thickness, including nainital or similar roof coverings and eaves boards of any description complete all as specified and directed.completed all as specified and directed by Engr-in-Charge. |
| 24 | S&F 12mm thick Gypsum board for ceiling fixed with GI Powder coated snap grid 605 x 605mm frame work as in false ceiling including hangers 4mm dia GI wire (upto 1200mm centre to centre upto length as required at site) and adjusting level fixed to roof wooden member by means of ceiling cleats made out of GI flat 40 x 3mm size 60mm long and expansion hold fasteners complete with and including dismantling ceiling baords of any description of any thickness incl cover fillets complete all as specified and directed by Engr-in-Charge. |
| 25 | S&F hasp and staple safety type 100 mm size, aluminium anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed including taking down old one. |
| 26 | S&F Extruded aluminium alloy handles 150 mm long fabricated type anodised complete all as specified and directed . |
| 27 | S&F Stainless Steel butt hinges medium weight of size 100 mm fixed with stainless screws complete all as specified and directed. |
| 28 | S&F 125mm size aluminium anodised, barrel tower bolt of extruded section complete all as specified and directed by Engr-in-Charge. |
| 29 | M&L rendering 15 mm thick in CM 1:6 on brick/concrete/stone wall surfaces of any description, and finishing the surfaces even and smooth without using extra cement complete withand including taking down cement or lime plaster of any description from stone /brick/concrete wall etc incl raking out joints hacking for key scrurbbing down with water and disposing of the rubbish complete all as specified and directed by Engr-in-Charge. |
| 30 | M&L brick work with sub class \"B\" bricks straight or curved in plan exc 6 mtr mean radius built in CM (1:6) using old size bricks with and including demolition of brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed by Engr-in-Charge. |
| 31 | M&L brick work with sub class \"B\" bricks straight or curved on plan to any radius in half brick thick wall built in CM 1:4 with and including demolition of brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed by Engr-in-Charge. |
| 32 | S&F 15 mm dia steel water GI tube medium grade with all fittings and fixed with concealed to walls, ceilings or laid in floors complete with and including taking up or down 15 mm bore steel water tubing and connections complete all as specified and directed by Engr-in-Charge. |
| 33 | M&L for Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete all as specified and directed by Engr-in-Charge. |
| 34 | S&F in repair 15 mm bib tap ( fancy type) , cast copper alloy chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed including taking down old one. |
| 35 | S&F in repair 15 mm bib tap cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed including taking down old one. |
| 36 | S&F in repair brass Chromium plated shower roses of size 125mm with or without swivel joints, any size, including fixing to steel pipe or unionincluding taking down old one. |
| 37 | S&F in repair CP angle valves (half turn type)/ conclead type (chromium plated fancy type) 15 mm dia, cast copper alloy, screwed down, high pressure with crutch or butterfly handles, screwed both end for iron pipe or for unions complete all as specified and directed including taking down old one. |
| 38 | S&F in repair 15 mm dia CP Wall Mixer Telephonic with Crutch (Provision for hand shower) and complete set of hand shower (Make : Prayag ) complete all as specified and directed. |
| 39 | S&F in repair 15 mm dia CP Central Hole Basin Mixer without Pop-up waste system (Make : Prayag) complete all as specified and directed. |
| 40 | S&F in repair 15 mm dia CP Sink Mixer with regular spout (W/M) (Make : Prayag) complete all as specified and directed. |
| 41 | S&F in repair Vitrous china wash hand basin, white, flat back of size 630 x 450 mm white excluding taps, waste, chain and plug and porcelain stopper but including bracket, cutting for and pinning the ends of brackets including PTMT waste coupling as suitable complete all as specified and directed by the Engr-in-Charge. |
| 42 | S&F in repair Vitrous china wash hand basin with full pedestal of size 835 x 560x440mm white or cream colourexcluding taps, waste, chain and plug and porcelain stopper but including bracket, cutting for and pinning the ends of brackets all as specified. |
| 43 | S&F in repair sinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x160mm complete all as specified and directed by Engr-in-Charge. |
| 44 | S&F waste pipe for kitchen snik and WHB of size 32/40mm dia upto 900 length complete all as specified and directed by Engr-in-Charge. |
| 45 | S&FCP grating dome 100 mm dia (minimum weight 25 gms) complete all as specified and directed including taking out old one. |
| 46 | S&F in repair Vitreous China wash down water closet pan (pedestal pattern), whitewith P or S trap with and including plastic water closet seat cover , connection to trap, flushing pipe & anti -syphonage pipe etc including necessary materials for fittings &making good to floor complete all as specified and directed by Engr-in-Charge.. |
| 47 | S&F in repair vitreous China, squatting pan, Orissa Pattern, size 630 x 450 mm white, with integral foot rests (excluding flushing cistern and flush pipe) with CI trap of suitable size ( P or S type) including connection to trap and to flushing pipe, anti syphonic pipe etc completeincluding provision of lime concrete bedding & making good to floor complete complete all as specified and directed including taking out old one. |
| 48 | S&F in repair 10 Ltr capacity PVC valveless syphonic action type flushing cistern low level white, with inlet, ball valve, float and handle including PVC flush pipe and brackets complete fixed in wall and floor to trap of WC as required and as directed. |
| 49 | S&F in repair 15 mm dia PVC connections, 450 mm long with PTMT nuts of suitable size at two end complete all as specified and directed including taking out old one. |
| 50 | S & F powder coated aluminumdoorwith the following specification and making good the adjacent surfaces complete all as specified and as directed:- (a)Cross section of xchowkhat frame 101.60x44.45x2mm thick. (b)Cross section of hanging and meetng style 83x44x2mm thick. (c) Top rail of cross section 114x44x2mm thick. (d)Bottom rail of cross section 114x44x2mm thick.(e)Locking rail (middle rail ) of cross section 83x44x2mm thick. (f)4mm thick tinted glassmake Modi, float . (g)Aluminum handle eisc type -02 Nos per shutter ( inside & out side). (h)Aluminum door stopper heavy duty-01 Nos per shutter. (i)Aluminum tower bolt 200mm long-01 Nos per shutter (inside). (j)Lock with key superior quality makae and type as approved by GE openable both from inside & out side -01 Nos per shutter. |
| 51 | S & F powder coated aluminium sliding glazedwindows with three track , three shutter sliding with following specification and making good the adjacent side etc . shifting of existing cooler stand where required complete all as specified and as directed by Engr-in-charge.(i)Windows frame of cross section 101mm x 44mm x 1.5mm thick.(ii)Three way track for sliding shutters of cross section91.8mm x 31.75mm x1.1mm thick.(iii)Sliding shutter frame of cross section40 x 18 x 1mm thick.(iv)4 mm thick tintedglass superior quality.(v) IDPE Rubber guasket for fixing of glass.(vi)Locking cleats per shutter -01 Nos.(vii)Sliding rollers per shutter - 02 Nos.(viii) Aluminium wire cloth 0.30mm nominal dia of wire and average width of aperture 1.56mm for shutters 01 Nos.(Ix)fixing screw for frame with wall per windows- 08 Nos |
| 52 | Hacking out old broken glass pane (any thickness , size, quality or description) from steel frame glazed with putty or fixed with beads. |
| 53 | M & L for 4 mm thick sheet glass ordinary quality and glazing with oil putty in square not exc. 0.5 sq m in each pane. |
| 54 | M & L for 4 mm thick figuredglass ordinary quality and glazing with oil putty in square not exc. 0.5 sq m in each pane. |
| 55 | S & F in repairs Galvnised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18 mmand fixed with tinned tacks, wooden beads or galvanised wire staples etc complete all as specified and directed. |
| 56 | Taking down shutter of any descriptionn exc. 1 Sqmeach complete. |
| 57 | Taking down shutter of any description exc. 1 Sqm but n. exc. 2 Sqm each complete. |
| 58 | Taking down chowkhats or frames not exc 1.5 sqm each without taking off shutter from the frame complete. |
| 59 | Taking down chowkhats or frame exc 1.5 sqm but not exc 4 sqm with shutter (without taking off shutter frome the frame ) |
| 60 | M&L Lagging to pipes used in internal water supply (internal dia of pipe 15mm) or plumbing all round with,25min thick bonded mineral wool preformed ‘SNAP ON’ pipe sections of density 144 Kg/cum conforming to IS 9842 all as specified and directed by the Engr-in-Charge. |
| 61 | M & L 2 nd class hard wood 35 mm thick Plain , framed panelled shutters ( any number of panels), with panels of timber flat on both sides (featheredged) or of veneered particle board medium density, wood particle board with commercial face veneers fitted to chowkats complete all as speciifed and directed. |
| 62 | S & F 2 nd class hard wood30 mm thick Glazed and skeleton shutters, open rebated and prepared to receive glass , gauze, etc, (with sash bar) edges divided into squares, with plain chamfered or rounded , mitred and rebated sash bars of any numbers ,beads,for securing glass etc, sizes of members of shutters as specified in SSR Part-I, section 8, clause 8.24(a) fitted to chowkats complete all as specified and directed. Note :- Glass pane and wire mesh shall be measured and paid separately inrespective supply only item. |
| 63 | S & F PVC solid factory made door frame of size 50 mm x 47 mm made out of 5 mm thick plain colour PVC sheet reinforced with MS square tubecomplete. |
| 64 | S & F factory made solid panel PVC door shutter 30 mm thick (Style) consisting of frame made out of MS tubes for top and bottom rails. MSframe shall be covered with heat molded plain colourPVC ‘C’ channel having a PVC sheet strip of 20 mm width struck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side and gap insert for top rail and bottom rail, paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement complete all as shown in SSR Part – II 2004 and as directed by GE/Engineer-in-Charge. |
| 65 | S&F 5mm thick plain colour PVC sheet in strips & channel feathered at the edges for fixing on Solid PVC Wall Lining, insulated PVC Wall Lining and solid PVC partition inclusive of solvent cement and fixing at site. Complete all as specified and directed. |
| 66 | S & F 100 mm size butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 complete . |
| 67 | S & F aluminium 150 mm long anodised barrel tower bolts ISI marked of extruded section and fixed complete. |
| 68 | S & F 150 mm size aluminium handles cast type, anodised ISI marked complete |
| 69 | S &F in repairs150mm lengthfloor door stopper of aluminium alloy body and tongue, anodized with hard drawn steel spring, fixed to floorcomplete all as specified and as directed |
| 70 | S & F 250 mm aluminium alloy, anodised sliding door bolt ISI marked with hasp, staple (bolt type) and fixing clips of sheet, cast of extruded sections and fixing bolts and sliding bolts of extruded sec or cast aluminium and fixed complete. |
| 71 | S & F in repairs door closer cast iron bodyhydraulically regulated , universaltype suitable for door shutters 851mm to 1000mm in width and weight between 61 to 80 kg of aluminum (die cast) body and fixed etc all as specified and as directed |
| 72 | S & F in repairs double action floor spring hudraulically regulated made up minimum 1.25 mm thick aluminium alloy sheet foundation box , main body with stainless cover, governig pivot made of brass other parts made of mild steel heavy duty complete all as specified and as directed. Make : KELWIN or equivqlent of other make as approved by GE. |
| 73 | M & L Preparation of New wood or previously untreated surfaces of any description , not otherwise description, over 10 cm width or grith apply two coat of synthetic enemel paint (ordinary tint) over a coat of pink primer complete all as specifed and directed. |
| 74 | M & L Preparation of Old wood painted surfaces of any description , not otherwise description, over 10 cm width or grith apply one coat of synthetic enemel paint (ordinary tint)complete all as specifed and directed. |
| 75 | M & L for preparation old painted surfaces of steel and iron work of any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed. |
| 76 | S&Frotational mouldedpolythenewaterstorage tank 500 ltrs(cylindricalvertical with closed top) hoistedand fixed in position all as specified inSSR Part-I with and including dismantling water tank of capacity exceeding 250 liters but not excedding 500 Ltrs andincluding 20mmball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule & nipple suitable for HDPE water tank (Min weight 15mm-38 gms/20mm-45gms/25mm-65gms) complete, all as specified and directed by Engr -in-Charge. |
| 77 | S&Frotational mouldedpolythenewaterstorage tank 1000 ltrs(cylindricalvertical with closed top) hoistedand fixed in position all as specified inSSR Part-I with and including dismantling water tank of capacity exceeding 500 liters but not excedding 1000 Ltrs and including 20mmball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule & nipple suitable for HDPE water tank (Min weight 15mm-38 gms/20mm-45gms/25mm-65gms) complete, all as specified and directed by Engr -in-Charge. |
| 78 | M & L for preparation of new or previously untreated steel surfaces of any description over 10 cm in width or girth not otherwise described and applying two coats of synthetic enamel paint over of redoxide zinc chrome coat complete all as specified and as directed. |
| 79 | Notes :- Amount of Credit Schedule for Schedule \"A\" Part-ll shall be deducted from total quoted amount of BOQ to arrive at the contract sum. |
