Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge.All kinds of soil0.00 LVL. TO 1.50 MTR. (D.S.R.-2.8.1) |
| 2 | 1.50 LVL. TO 3.00 MTR. (D.S.R.-2.8.1+2.26.1) |
| 3 | Filling available excavated earth (excluding rock) in trenches, plinth,sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. ((D.S.R.-2.25)) |
| 4 | Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete. ((D.S.R.-2.25a)) |
| 5 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :, 1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) ((D.S.R.-4.1.8)) |
| 6 | Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. ((D.S.R.-2.27)) |
| 7 | With Chlorpyriphos/ Linadane E.C. 20% with 1% concentration. ((D.S.R.-2.35.3.1)) |
| 8 | Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard settingof concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge, for the followinggrades of concrete.: Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content,the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.Concrete of M25 grade with minimum cement content of 330 kg /cum, All works above plinth level upto floor V level ((D.S.R.-5.33.2.1)) SLAB) |
| 9 | All works above plinth level upto floor V level ((D.S.R.-5.33.2.1)) (BEAM) |
| 10 | All works upto plinth level ((D.S.R.-5.33.1.1)) FOOTING |
| 11 | All works upto plinth level ((D.S.R.-5.33.1.1)) (COLUMN) |
| 12 | All works upto plinth level ((D.S.R.-5.33.1.1)) |
| 13 | Add for using extra cement in the items of design mix over and above the specified cement content therein. (D.S.R.-5.35) |
| 14 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:Cement mortar 1:6 (1 cement : 6 coarse sand) ((D.S.R.-6.1.2)) |
| 15 | Providing and laying damp-proof course 40 mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 12.5 mm nominal size). ((DSR-4.10)) |
| 16 | Painting on D.P.C. with two coats of airblown bitumen 85/50 or 85/25 @ 1.7 kg/sqm approx. including cost of fuel if any. ((DSR-4.13)) |
| 17 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :Cement mortar 1:6 (1 cement : 6 coarse sand), Ground Floor |
| 18 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.Cement mortar 1:4 (1 cement :4 coarse sand), Ground Floor |
| 19 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.Thermo-Mechanically Treated bars of grade Fe-500D or more., Ground Floor |
| 20 | 15 mm cement plaster on rough side of single or half brick wall of mix:1:6 (1 cement: 6 coarse sand) ((DSR-13.5.2)), Ground Floor |
| 21 | 12 mm cement plaster of mix :1:6 (1 cement: 6 coarse sand) ((DSR-13.4.2)), Ground Floor |
| 22 | 15 mm cement plaster on rough side of single or half brick wall of mix : 1:4 (1 cement: 4 coarse sand). ((DSR-13.5.1)) |
| 23 | Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections. ((DSR-5.30)) |
| 24 | Providing and fixing 18mm thick gang saw cut mirror polished premoulded and prepolished) machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of required size of approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade. (FLOORING), Ground Floor ((DSR-8.2.2.2 )) |
| 25 | Providing and fixing 18mm thick gang saw cut mirror polished premoulded and prepolished) machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of required size of approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade. (skirting), Ground Floor ((DSR-8.2.2.2 )) |
| 26 | Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth ((DSR-4.17)) |
| 27 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:, (a) 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws. Single leaf. ((DSR-9.21.1)) |
| 28 | (b) Double leaf (((DSR-9.21.1+9.26)) |
| 29 | Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners,including drilling of holes for fixing hardware\"s and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.Note: For uPVC frame and sash extruded profiles minus 5% tolerancein dimension i.e. in depth & width of profile shall be acceptable.Three track three panels sliding window with two glazed & one wire mesh panels with alluminium channel for roller track, wool pile, nylon rollers with s.s. 304 body., Using R2 series with foame (70mm & above)x(40 mm & above) & both glazed and fly screen sash (25 mm & above)x(50mm & above with zinc alloy (zamak) powder coated touch lock with hook (Height up to 1.20 meter) (D.S.R.-9.147 A4.1) |
| 30 | Providing and fixing M.S. Tubular frames for doors, windows, ventilators and cupboard with rectangular/ L-Type sections, made of 1.60 mm thick M.S. Sheet, joints mitred, welded and grinded finish, with profiles of required size, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer., Fixing with carbon steel galvanised dash fastener of requireddia and size (to be paid for separately) (D.S.R. 10.15.2) |
| 31 | Painting with silicon & acrylic emulsion based water thinnable sealer of approved brand and manufacture on wet or patchy portion of plastered surfaces :Two coats, Ground Floor |
| 32 | Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade:New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)(Outer surface), Ground Floor |
| 33 | Distempering (Two coat) with oil bound distemper of approved brand and manufacture & of required shade on undecorated wall surface to give an even shade over & including a priming coat with cement primer of approved brand & manufacture such as Berger,J&N, Shalimar, Asian paints after thoroughly brushing the surface free from mortar droppings & other foreign matters & also including preparing the surface even with plaster of paris or approved synthetic material & sand papered smooth including cost ofall materials. (For ceiling surface), Ground Floor |
| 34 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. , Ground Floor |
| 35 | Centering and shuttering including strutting, propping etc. and removal of form for :, Foundations, footings, bases of columns, etc. for mass concrete (D.S.R.-5.9.1) |
| 36 | Suspended floors, roofs, landings, balconies and access platform with water proof ply 12 mm thick (D.S.R.-5.9.20) |
| 37 | Lintels, beams, plinth beams, girders, bressumers and cantilevers with water proof ply 12 mm thick (D.S.R.-5.9.21) |
| 38 | Columns, Pillars, Piers, Abutments, Posts and Struts (D.S.R.-5.9.6) |
| 39 | Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge. ((D.S.R.-10.28)) |
| 40 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished seamless type tubes, Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished seamless type tubes (D.S.R.-10.16.2) |
| 41 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade.Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture : (M.S. works). ((D.S.R.-13.62.1)) |
| 42 | Providing and fixing in position Colour Natural anodized heavy duty Aluminium Doors/windows/ Sections for outer frame, shutter frame, mullions, beads etc. including providing and fixing hardware items, 6mm clear float glass, approved EPDM gasket, wool pie, cleats and other accessories as required. Anodic coating shall be 0.025 mm as per Standard Code. The Aluminium frame will not be less than 2.75 mm thick. The rate shall include caulking around frames with polysulphide sealant, wherever required, SS friction hinges handles, locks, concealed tower bolts etc. as per approved makes and specifications. The contractor has to provide shop drawings before the commencement of work for the architect\"s approval. The contractor has to follow profiles of the sections shown in the Drawing or approved equivalent to the mentioned. Appropriate profiles of EPDM gaskets shall be inserted between aluminium frames/ beadings and glass; as well as both inside and outside around the periphery of the shutters, to make the windows air and water-tight. The fixing shall be done on aluminium rough ground openings at anchorage locations, in jambs, sills and heads by drilling holes with an electric drill, inserting Stainless Steel Counter sunk screws. The entire periphery shall be sealed by application of approved weather silicon sealant between the aluminium and masonry from both outside and inside to make the windows watertight. Each openable window shutter shall be provided 2 nos. of 255mm adjustable Stainless Steel Friction stay, button locking handle as per the design to be approved by the Architect. Door shutters with lock, handles, tower bolt, door stoppers, hinges as required, floor springs/Hydraulic door closer etc. complete. Rate inclusive of 6mm thick toughened glass/ 4mm thick ACP Sheet. The Contractor shall make provision for cutting of glass wherever required as per drawing and as required by the Architect. (Area of door and windows shall be measured for payment purpose). (NSR.) |
| 43 | Supply and fixing of approved Make Motorized Galvanized Steel Single Wall Rolling Shutter, vertical rolling type, used for internal and external applications. The rolling shutter components include Galvanized Steel Slats (as per IS 6248), MS Bottom Plate, MS Side Guides, MS Brackets, MS Shaft Assembly (all with one coat of standard primer), GI Hood Cover, and Hardware. The Imported Make Automation System consists of an Indirect Drive with a chain wheel mechanism, a Manual hand chain for emergency operation, an Inbuilt control, a 3-way push button, safety, and operating accessories. Slat Curtain: Galvanized Steel slats (1.0 mm thick for shutter width >3.5m and 0.9 mm thick for shutter width <3.5m) with continuous single piece without joints, 88 mm corrugated type profile. Bottom Plate: GI bottom plate 2.5 mm thick with angle stiffener, L-shaped bottom profile (120 mm height), optional rubber sealing. Side Guides: GI Box Type Guide, 100 x 85 x 2 mm thick. Bracket Plate: Mild Steel, minimum 3.0 mm thick, motor side bracket with chain-sprocket mechanism, other side with bearings. Roller Shaft: Mild Steel hollow tubular pipe, diameter 100-300 mm, machined shaft and flange, slat curtain fixed by nuts & bolts. Hood Cover: GI sheet, 0.8 mm thick, hexagonal shape. Automation System: Electric motor (Imported Make), 220 V / 380 V, 1 phase or 3 phase, emergency chain wheel drive, safety device, inbuilt thermostat. Control: Inbuilt Basic control card with integrated limit switch. Standard Accessories: Push Button, 3-way Push Button standard with automation system, motor cover (GI sheet, 0.8 mm thick), bottom rubber sealing, manual hand chain, including powder coat painting on both sides of shutter & wherever necessary as per approved color, etc., complete in all respects. (NSR.) |
| 44 | Providing and installation of customised vertical concrete panels with precise dimensions and robust material specifications. Each panel measures 120 mm in width, 1500 mm in height, and has a thickness of 22 mm having flutes/grooves/undulation or of approved size of desired finish and pattern including the cost of graphics illustrations as approved by Architect in charge. The composition of tiles should be ‘43’ Grade Portland cement and homogeny pigmentation should be done with exterior grade synthetic inorganic iron oxide pigments. e pigmentation should be homogeneous and in accordance with British Standards BS EN 12878:1999. The other additives should be fine washed graded quartz, super plasticisers and integrated water proofing agents and others. The tiles should be produced with high vibration technology and concrete mix design compressive strength equivalent to M-40 Grade@28 days. The top surface of the tiles should be sealed with in surface water absorption of tiles, less than 1% and water absorption by 24 hrs immersion method, less than 8%. The tiles should be applied on a rough plaster of 1:3 cement mortar 1:3 (1 cement: 3 coarse sand) and the fixing of tiles should be done by ‘Greyscale’ tile adhesive or equivalent as per manufacturer’s laying instruction. ln addition to thistiles will also have an inSert of L profile fixed using epoxy and screwed on the wallfor additional safety. The installation should be meticulously carried out under the guidance and approval of the appointed Architect or Engineer-in-Charge, ensuring that all work is executed to the highest standards of quality and precision. (NSR) |
| 45 | Design, fabricating, supply and installation of customised perforated MS sheet in extruded triangular or parametrically eveolved pattern as approved by drawing submitted to Architect in charge at all levels mild steel (MS) sheets, which includes a series of detailed processes to achieve the desired design and finish through CNC cutting, which allows for precise and intricate patterns to be cut into the MS sheet based on the approved drawings and designs provided by the Architect in charge. Following the cutting process, etching and engraving are performed to add depth and detail to the design, enhancing the ornamental appearance. These processes involve carefully removing material from the surface to create the desired patterns and textures. After the cutting, etching, and engraving are completed, refilling is conducted to ensure the engraved areas are smooth and consistent with the overall design. This step ensures that the intricate details are highlighted and any imperfections are corrected. The MS sheet used for this work will be of an approved thickness to ensure structural integrity and durability. Additionally, the specification includes the cost of powder coating the MS sheet in an approved shade. (NSR ) |
| 46 | Providing and fixing roofing consist of 0.8 mm thick galvanized steel deck sheet confirming to IS 277:1992 used as permanent shuttering over which MS wire mesh 3 mm laid at 100x100 mm grid including edge trim covered with concrete. This metal deck will be supported on structural steel beam with shear studs. (Structural steel like Beam, column, joists etc. & concrete of different grade as per design will be paid separately). (NSR) |
| 47 | DOUBLE SKIN ROOF SHEETING Providing & fixing Top layer of profile sheet of 1015 mm effective cover width and nominal 28.5 mm deep ribs with subtle square fluting in the five pans at nominal 200 mm centre to-centre. The end rib shall be designed for anti-capillary action, to avoid any seepage of water through the lateral overlap. The feed material is manufactured out of nominal 0.50 mm Total Coated Thickness (TCT), Hi-Tensile steel with min. 550 mpa yield strength, metallic hot dip coated with Aluminum-Zinc alloy (55% Aluminum, 45% Zinc) as per AS 1397 - Zincalume AZ150 (Min. 150 gms/sq.mt total on both sides). Thereafter providing sub girt in 0.5 mm thickness in Z shape of 50 mm web and 20 mm flange over bottom skin sheet shall be Panel rib profile of LYSAGHT to be installed over purlins directly with self drilling & tapping screws. to make air gap of 50 mm for providing sandwich insulation of 50 mm thick rock wool pads having density of 48 kg/mtr cube with HDPE vapor liners on both top and bottom surface of Rock wool. Complete job with all hardware, accessories, material and labour. (NSR) |
| 48 | Design & Fabricating Ornamental work on mild steel (MS) sheets, which includes a series of detailed processes to achieve the desired design and finish through CNC cutting, which allows for precise and intricate patterns to be cut into the MS sheet based on the approved drawings and designs provided by the Architect in charge. Following the cutting process, etching and engraving are performed to add depth and detail to the design, enhancing the ornamental appearance. These processes involve carefully removing material from the surface to create the desired patterns and textures. After the cutting, etching, and engraving are completed, refilling is conducted to ensure the engraved areas are smooth and consistent with the overall design. This step ensures that the intricate details are highlighted and any imperfections are corrected. The MS sheet used for this work will be of an approved thickness to ensure structural integrity and durability. Additionally, the specification includes the cost of powder coating the MS sheet in an approved shade. (make Metaguise/Citadel/ Woodform Architectural or equivalent) (NSR) |
| 49 | Providing and fixing Structural Glazing consisting of fixed panels as per the elevation drawings enclosed, fabricated out of heavy-duty aluminium extruded profiles anodized (25 microns) as per approved shade. All aluminium members & profiles shall be of AC 25 grade as per specification. The Aluminium members shall be protected with Masking Tapes all around the profiles for safety against external scratches at the site. (Masking Tapes shall be removed only at the time of handing over as per the instructions of the Project Manager).Structural Glazing as above with 6mm thick touSupply of colour coated Nominal 0.45mm base metal thickness (0.50mm TCT) LYSAGHT CUSTOMORB sinusoidal profile of 990 mm effective cover width, with fourteen smooth sinusoidal corrugation, 19mm rib height spaced at 76mm c/c. The end rib shall have anti-capillary groove. The steel sheet is having high tensile sheet G550 (Fy=550Mpa), metallic coated with Zinc Aluminium alloy (i.e. 55% Al, 43.4% Zinc, 1.6% Si - Zincalume), AZ150 (min 150 gm/m2 total on both side), pre-painted with Super Durable Polyester Colorbond XRW quality paint includes inorganic infrared reflective pigment (High SRI-”Thermatech technology”) of 20μm exterior coat on top surface and 5μm reverse coat on back surface over 5μm primer coat on both surfaces of approved color shade by concern authority. The sheet conforms to general requirement of AS/NZS 2728 type 4 / IS 15965 class 3 durability and gloss value of 25% - 40% of Tata BlueScope Steel make. The sheet shall have brand marking of the manufacturer giving product details on the back of the sheet at every 1 meter c/c for confirming genuinity of the material. ghened Glass (Make - Asahi, Series- Ecosence Enhance / Solar control Glass) as per approved colour.All the accessories like flashing / capping shall be made from the material specifications (0.45MM BMT /0.5 MM TCT, COLORBOND® XRW) G 550 mentioned as above in approved colour shade & as per manufacturers’ recommendation Including Acp Sheet . ( NSR) (NSR) |
| 50 | Providing and fixing of colour coated Nominal 0.45mm base metal thickness (0.50mm TCT) LYSAGHT CUSTOMORB sinusoidal profile of 990 mm effective cover width, with fourteen smooth sinusoidal corrugation, 19mm rib height spaced at 76mm c/c. The end rib shall have anti-capillary groove. The steel sheet is having high tensile sheet G550 (Fy=550Mpa), metallic coated with Zinc Aluminium alloy (i.e. 55% Al, 43.4% Zinc, 1.6% Si - Zincalume), AZ150 (min 150 gm/m2 total on both side), pre-painted with Super Durable Polyester Colorbond XRW quality paint includes inorganic infrared reflective pigment (High SRI-”Thermatech technology”) of 20μm exterior coat on top surface and 5μm reverse coat on back surface over 5μm primer coat on both surfaces of approved color shade by concern authority. The sheet conforms to general requirement of AS/NZS 2728 type 4 / IS 15965 class 3 durability and gloss value of 25% - 40% of Tata BlueScope Steel make. The sheet shall have brand marking of the manufacturer giving product details on the back of the sheet at every 1 meter c/c for confirming genuinity of the material. All the accessories like flashing / capping shall be made from the material specifications (0.45MM BMT /0.5 MM TCT, COLORBOND® XRW) G 550 mentioned as above in approved colour shade & as per manufacturers’ recommendation.0 to 305mm Girth (NSR) |
| 51 | 306 to 610mm Girth (NSR) |
| 52 | Providing and fixing heavy-duty hardware fittings manufactured from Stainless Steel Grade 304, finished with a bright polished brass or lacquered PVD (Physical Vapor Deposition) finish as specified, to be installed on door shutters of required thickness. The work includes 150 mm heavy-duty Decorative Door Stoppers provided with a high-quality, durable vulcanized rubber cushion to prevent impact damage, along with door bolts, tower bolts, and handles of required sizes. The work includes 150 mm heavy-duty door stoppers provided with a high-quality, durable vulcanized rubber cushion to prevent impact damage, along with door bolts, tower bolts, and handles of required sizes (NSR-1) |
| 53 | Providing and fixing heavy-duty door handles manufactured from Stainless Steel Grade 304, finished with a high-gloss bright polished brass lacquered PVD finish as per approved shade and design. The handles shall be of the required size 125 mm and fixed to door shutters of varying thicknesses as per the direction of the Architect/Engineer-in-Charge. with material test certificate. (ODG-11-10x125) (NSR) |
| 54 | Providing & fixing EN:1154 Certified 500000 cycle tested door closer made of Aluminium Diecasted body having UL stamping sutable for 80kg with double speed adjustment with necessary accessories and screws etc. Complete. (NSK-680) (NSR) |
| 55 | Providing and fixing powder-coated aluminium work for partitions, made of standard hollow sections (Hindalco or equivalent) as per the approved drawings and design. The framework shall consist of 45x45 mm sections with a wall thickness of 1.5 mm (16 gauge), manufactured from Aluminium Alloy 6063-T6. The sections shall be powder-coated with a minimum thickness of 50 microns in the specified color. The structure is to be fixed with expansion hold-fasts, rawl plugs, and high-quality stainless steel screws.The partition shall be glazed with 5 mm thick clear float glass (of approved make like Saint-Gobain/ModiGuard), secured using EPDM rubber gaskets and glazing clips to ensure a rattle-free and airtight finish. The work includes all necessary hardware, including cleats, joints, and sealants to make the partition perfectly rigid and aligned. All joints shall be miter-cut at 45° or butt-jointed as per the direction of the Engineer-in-Charge. The rate includes the cost of all materials, labor, scaffolding, and cleaning of glass/sections upon completion. (NSR.) |
| 56 | Design development, coordination, and preparation of detailed shop drawings and fabrication drawings for all prefabricated components, strictly based on architectural drawings and design inputs received from the Architect-In-Charge, including structural framing, façade systems, cladding, decks, staircases, shutters, signage, and allied elements; comprising study of drawings, design coordination, preparation of execution-ready and CNC-compatible fabrication drawings with complete detailing of members, connections, fixings, materials, finishes, tolerances, and installation methodology; including all revisions, modifications, coordination meetings, and final approvals, prepared in compliance with applicable Indian Codes and Standards, complete in all respects as directed by the Engineer-in-Charge. (NSR) |
| 57 | Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc.Internal work - Exposed on wall 15 mm nominal outer dia pipes (DSR -18.10.1) |
| 58 | 20 mm nominal outer dia pipes (DSR -18.10.2) |
| 59 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge., Internal work - Exposed on wall20 mm nominal outer dia Pipes (DSR -18.7.2) |
| 60 | 25 mm nominal outer dia Pipes (DSR -18.7.3) |
| 61 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings, with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc., 15 mm nominal outer dia pipes (DSR -18.8.1) |
| 62 | 20 mm nominal outer dia pipes (DSR -18.8.2) |
| 63 | Providing and fixing G.I. pipes complete with GI fittings and clamps including cutting and making good the walls etc. External work, 40 mm dia, nominal bore (DSR -18.12.5) |
| 64 | 50 mm dia, nominal bore (DSR -18.12.6) |
| 65 | Providing and fixing of gun metal gate valve with CI wheel of approved quality (screwed ends), 25mm dia, nominal bore (DSR -18.17.1) |
| 66 | 32 mm dia, nominal bore (DSR -18.17.2) |
| 67 | 40 mm dia, nominal bore (DSR -18.17.3) |
| 68 | 50 mm dia, nominal bore (DSR -18.17.4) |
| 69 | Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete :, 25 to 40 mm nominal bore (DSR -18.13.1) |
| 70 | 50 to 80 mm nominal bore (DSR -18.13.2) |
| 71 | Providing and fixing uplasticised PVC connection pipe with brass unions : 45 cm length, 15 mm nominal bore (DSR -18.21.2.1) |
| 72 | Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet 100 mm diameter (DSR -18.22.1) |
| 73 | Painting G.I. pipes and fittings with synthetic enamel white paint with two coats over a ready mixed priming coat, both of approved quality for new work (internal work -exposed on , walls)15 mm nominal outer dia pipes (DSR -18.38.1) |
| 74 | 20 mm nominal outer dia pipes (DSR -18.38.2) |
| 75 | Painting GI pipes and fittings with two coats of anti corrosive bitumastic paint of approved quality, 40 mm dia, nominal bore (DSR -18.40.5) |
| 76 | 50 mm dia, nominal bore (DSR -18.40.6) |
| 77 | Providing and filling sand of grading zone V or coarser grade, allround the G.I. pipes in external work, 40 mm dia, nominal bore (DSR -18.41.5) |
| 78 | 50 mm dia, nominal bore (DSR -18.41.6) |
| 79 | Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :, 20 mm nominal bore (DSR -18.18.2) |
| 80 | 25 mm nominal bore (DSR -18.18.3) |
| 81 | Providing and fixing G.I. union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (new work), 15mm nominal bore (DSR -18.46.1) |
| 82 | 20mm nominal bore (DSR -18.46.2) |
| 83 | 25mm nominal bore (DSR -18.46.3) |
| 84 | 32mm nominal bore (DSR -18.46.4) |
| 85 | Providing and fixing C.P. brass bib cock of approved quality confirming to IS:8931, 15mm nominal bore (DSR -18.49.1) |
| 86 | Providing & fixing chrome plated brass battery based infrared sensor operated pillar cock, having foam flow technology., 15mm nominal bore (DSR -18.84.1 ) |
| 87 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS 8931 a) 15 mm nominal bore., 15 mm nominal bore (DSR -18.53.1) |
| 88 | Excavating trenches of required width for pipes, cables, etc, including excavation for sockets, depth upto 1.5 m including getting out the excavated materials, returning the soil as required in layers not exceeding 20 cm in depth including consolidating each deposited layers by ramming, watering etc. stacking serviceable material for measurements and disposal of unserviceable material as directed, within a lead of 50m :, Pipes, cables etc. exceeding 80 mm dia but not exceeding 300 mm dia. (DSR -2.10.1.2) |
| 89 | Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete :, 100 mm O.D. (DSR -19.6.1) |
| 90 | 150 mm O.D. (DSR -19.6.2) |
| 91 | Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per standard design : , 110/100 mm diaRmt pipe (DSR -19.2.1) |
| 92 | 160/150 mm diaRmt pipe (DSR -19.2.2) |
| 93 | Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: 180x150 mm size P type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 (DSR -19.4.3.1) |
| 94 | Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) Fisnihed with a floating coat of neat cement complete as per standard design :Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) :With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 (DSR -19.7.1.1) |
| 95 | (b) Inside size 1200 x 1200mm and 1.0meter deep including C.I. Cover frame. (DSR -19.7.2.1) |
| 96 | Extra over Item No. 24.27 for every additional depth of 0.10 metre or part there of main hole(a) Size 900 x 800 mmWith common burnt clay F.P.S. (non modular) bricks of class designation 7.5 (DSR -19.8.1.1) |
| 97 | (b) Size 1200 x 900mm With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 (DSR -19.8.2.1) |
| 98 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc., For Internal Toilet , 15 mm nominal outer dia Pipes (DSR -18.8.1) |
| 99 | 20 mm nominal outer dia Pipes (DSR -18.8.2) |
| 100 | 25 mm nominal outer dia Pipes (DSR -18.8.3) |
| 101 | 32 mm nominal outer dia Pipes (DSR -18.8.4) |
| 102 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. (DSR -18.7), Internal work - Exposed on wall , 20 mm nominal bore (DSR -18.7.2) |
| 103 | 25 mm nominal bore (DSR -18.7.3) |
| 104 | 32 mm nominal bore (DSR -18.7.4) |
| 105 | 40 mm nominal bore (DSR -18.7.5) |
| 106 | Providing and fixing GI pipes complete with GI fittings and clamps, i/c cutting and making good the walls etc. Internal work - Exposed on Wall, Terrace loop & Tank Filling Pipe, 20 mm nominal bore (DSR -18.10.2) |
| 107 | 25 mm nominal bore (DSR -18.10.3) |
| 108 | 32 mm nominal bore (DSR -18.10.4) |
| 109 | 40 mm nominal bore (DSR -18.10.5) |
| 110 | 50 mm nominal bore (DSR -18.10.6) |
| 111 | Painting G.I. pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality , 20mm diaRmt pipe (DSR -18.40.2) |
| 112 | 25mm diaRmt pipe (DSR -18.40.3) |
| 113 | 32mm diaRmt pipe (DSR -18.40.4) |
| 114 | 40mm diaRmt pipe (DSR -18.40.5) |
| 115 | 50mm diaRmt pipe (DSR -18.40.6) |
| 116 | 65mm diaRmt pipe (DSR -18.40.7) |
| 117 | 80mm diaRmt pipe (DSR -18.40.8) |
| 118 | Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) , 20mm diameter pipe (DSR -18.46.2) |
| 119 | 25mm diameter pipe (DSR -18.46.3) |
| 120 | 32mm diameter pipe (DSR -18.46.4) |
| 121 | 40mm diameter pipe (DSR -18.46.5) |
| 122 | 50mm diameter pipe (DSR -18.46.6) |
| 123 | 65mm diameter pipe (DSR -18.46.7) |
| 124 | 80mm diameter pipe (DSR -18.46.8) |
| 125 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : For vertical pipe connection with terrace ringmain, 20 mm nominal bore (DSR -18.17.1A) |
| 126 | 25mm nominal bore (DSR -18.17.1) |
| 127 | 32mm nominal bore (DSR -18.17.2) |
| 128 | 40mm nominal bore (DSR -18.17.3) |
| 129 | 50mm nominal bore (DSR -18.17.4) |
| 130 | 65mm nominal bore (DSR -18.17.5) |
| 131 | 80mm nominal bore (DSR -18.17.6) |
| 132 | Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete , 25 to 40 mm nominal bore (DSR -18.13.1) |
| 133 | 50 to 80 mm nominal bore (DSR -18.13.2) |
| 134 | Providing and fixing PTMT Ball cock of approved quality, colour and make complete with Epoxy coated aluminium rod with L.P./H.P.H.D. plastic ball. , 15 mm nominal bore, 105 mm long, weighing not less than 138 gms (DSR -18.62.1) |
| 135 | 20 mm nominal bore, 120 mm long, weighing not less than 198 gms (DSR -18.62.2) |
| 136 | 25 mm nominal bore, 152 mm long, weighing not less than 440 gms (DSR -18.62.3) |
| 137 | 40 mm nominal bore, 206 mm long, weighing not less than 690 gms (DSR -18.62.4) |
| 138 | 50 mm nominal bore, 242 mm long, weighing not less than 1240 gms (DSR -18.62.5) |
| 139 | Providing and fixing MS pipe puddle flanges of required size with 600mm long with 6mm thick MS plate of size 300mm x 300mm of suitable size properly fixed in RCC walls of water tanks, including necessary welding complete in all respect as per details shown on darwings and directions of Engineeer-in-charge for water tanks., 25mm dia. (NSR) |
| 140 | 40mm dia. (NSR) |
| 141 | 50mm dia. (NSR) |
| 142 | 80mm dia. (NSR) |
| 143 | 100mm dia. (NSR) |
| 144 | 150mm dia. (NSR) |
| 145 | 200mm dia. (NSR) |
| 146 | 250mm dia. (NSR) |
| 147 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS :13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes., 110 mm dia (for rain water) (DSR -12.41.2) |
| 148 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion., Single Push Fit Coupler, 110 mm dia (DSR -12.42.2.2) |
| 149 | Single tee with door, 110x110x110 mm (DSR -12.42.3.2) |
| 150 | Plain bend 87.5 deg , 110 mm dia (DSR -12.42.5.2) |
| 151 | Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete, 110 mm dia (DSR -12.43.2) |
| 152 | Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. (DSR -12.22) |
| 153 | Providing and fixing 15 cm wide, 45 cm overall semi-circular plain G.S. sheet gutter with iron brackets 40x3mm size, bolts, nuts and washers etc., including making necessary connections with rain water pipes complete, 0.80 mm thick with zinc coating not less than 275 gm/m² (DSR -12.7.1) |
| 154 | Excavating trenches by mechinical / manual means of required width for pipes cables etc including excavation for sockets, and dressing of sides, ramming of bottoms, for all depth including getting out the excavated soil , and then returning the soil as required , in layers not exceeding 20 cm in depth including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed , within a lead of 50 m. All kind of soil , Pipes, cables etc. exceeding 80 mm dia . But not exceeding 300mm dia. (DSR -2.10.1.2) |
| 155 | Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per standard design: , 100mm dia SW pipe (DSR -19.2.1) |
| 156 | Providing, fixing, jointing and testing, uPVC SWR pipes, - type B conforming to IS : 13592 to wall, ceiling and floor, approved quality, complete, for soil, waste & rain water drain including pushfit jointing with seal ring. (i) Single socketed pipes. (NSR), Internal Toilet (Soil & Waste Pipe), 75 mm (NSR) |
| 157 | 110 mm (NSR) |
| 158 | Exposed on Wall (Soil & Waste Pipe), 110 mm (NSR) |
| 159 | Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories for unplasticised Rigid PVC pipes including jointing with seal ring leaving 10 mm gap for thermal expansion. (NSR), Bend without door (45°) (NSR), 75mm |
| 160 | 110mm |
| 161 | Bend without door (87.5°) (NSR), 75mm bend |
| 162 | 110mm |
| 163 | Y\" Fitting without door (NSR), 75mm |
| 164 | 110mm |
| 165 | Single Tee without door (NSR), 75mm |
| 166 | 110 mm |
| 167 | Single Tee with door (NSR), 75mm |
| 168 | 110 mm |
| 169 | Bend with door (87.5°) (NSR), 75mm |
| 170 | 110 mm |
| 171 | v, 75mm |
| 172 | 110 mm |
| 173 | Reduced \"Y\" Fitting without door (NSR), 110mm x 75mm |
| 174 | Reduced Tee with door (NSR), 110mm x 75mm |
| 175 | Coupler (NSR), 75mm |
| 176 | 110mm |
| 177 | Vent Cowl (NSR), 110mm |
| 178 | Providing, fixing, jointing and testing, unplasticized PVC pipes - 10 kg/cm2 confirming to IS : 4985 to wall, ceiling and floor, approved quality, complete, for waste water drain including jointing with rubbering/solvent/solution and airtight joints, etc. For Wash basin & Urinal (NSR), 32mm dia. Pipe (NSR) |
| 179 | 50mm dia. pipe (NSR) |
| 180 | Elbow (45°) (NSR), 32mm |
| 181 | Elbow (90°) (NSR), 32mm |
| 182 | T fitting (NSR), 32mm |
| 183 | Coupler (NSR), 32mm |
| 184 | Providing, fixing, jointing and testing , of PVC Multi Floor Trap without jali of minimum 50 mm water seal, making necessary cutting in slab or floors and making good including supports with cement concrete 1:3:6 complete as approved by Engineer-in-Charge., 110mm x 75mm x 50mm/40mm (Toilet) NSR |
| 185 | Providing, fixing, jointing and testing , of PVC Nahani Trap without jali of minimum 50 mm water seal, making necessary cutting in slab or floors and making good including supports with cement concrete 1:3:6 complete as approved by Engineer-in-Charge, 110mm x 75mm (Toilet & Kitchen) (NSR) |
| 186 | Providing and fixing PTMT grating of approved quality and colour, Rectangular type with openable circular lid., 150 mm nominal size square 100 mm diameter of the inner hinged round grating (including balcony) (DSR -18.58.2.1) |
| 187 | Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design 150 x 100mm size P-type , With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 (DSR -19.4.2.1) |
| 188 | Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete:, 100 mm diaRmt (DSR -19.1.1) |
| 189 | Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:, White Vitreous china Orissa pattern W.C. pan of size600x500 mm with integral type foot rests (NSR) |
| 190 | Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required :, W.C. pan with ISI marked white solid plastic seat and lid (DSR -17.2.1) |
| 191 | Providing and fixing of wall mounting type water closet of approved quality & make and as per the direction of Engineer-in-charge. (NSR) |
| 192 | Providing and fixing of S.STEEL TOILET PAPER HOLDER(WITH FLAP) of approved quality & make and as per the direction of Engineer-in-charge. (NSR) |
| 193 | Providing and fixing of SANITARY BIN WITH PEDAL,18 LITERS, BLACK of approved quality & make and as per the direction of Engineer-in-charge. (NSR) |
| 194 | Providing and fixing of SWING HANDICAP GRAB BAR -S.STEEL, 32MM DIA. of approved quality & make and as per the direction of Engineer-in-charge. (for H. Toilet) (NSR) |
| 195 | Providing and fixing of S.STEEL GRAB RAIL,300MM,32MM DIA of approved quality & make and as per the direction of Engineer-in-charge. (for H. Toilet) (NSR) |
| 196 | Providing and fixing Hand Shower (Health Faucet) with 8mm Dia,1.2 Meter Long Flexible Tube & Wall Hook of approved quality and make as approved by Engineer - in - charge. (NSR) |
| 197 | Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge. (DSR -17.16A) |
| 198 | Providing and fixing of Under Counter Basin of approved quality & make and as per the direction of Engineer-in-charge. (NSR) |
| 199 | Providing and fixing of AUTOMATIC TAP, BASIN MOUNT of approved quality & make and as per the direction of Engineer-in-charge. (NSR) |
| 200 | Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:- , (a) White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer |
| 201 | Providing and fixing of AUTO SOAP DISPENSER of approved quality & make and as per the direction of Engineer-in-charge. (NSR) |
| 202 | Providing and fixing of S.STEEL HAND DRYER (HEAVYTRAFFIC ) of approved quality & make and as per the direction of Engineer-in-charge. (NSR) |
| 203 | Providing and fixing of AUTOMATIC HRT TISSUE PAPERROLL DISPENSER of approved quality & make and as per the direction of Engineer-in-charge. (NSR) |
| 204 | Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms. (DSR -17.72) |
| 205 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. (DSR -17.31) |
| 206 | Providing and fixing Stainless Steel AISI 304 (18/8) kitchen sink as per IS: 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever require, Kitchen sink with drain board, 510x1040 mm bowl depth 200 mm (DSR -17.10.1.3) |
| 207 | Providing and fixing of URINAL WITH SENSOR (BATTERY + ELECTRICAL) of approved quality & make and as per the direction of Engineer-in-charge. (NSR) |
| 208 | Providing and fixing of Kent Elite Plus Water Purifier, cooler complete (RO+UV+UF+TDS Control) with flow rate (50L/hr) including all its accessories, complete in all respect including testing etc. (NSR) |
| 209 | (a) Supplying, installation, testing and commissioning of electric driven terrace pump conforming to IS 12469: 2019 suitable for automatic operation and consisting of following, complete in all respects, as required: (Terrace Pump) (b) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical seal as required. (c)Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase, 50 Hz, AC supply with IP55 class of protection for enclosure, horiziontal foot mounted type with Class \"F\" insulation, conforming to IS-12615: 2018. (d) M.S.fabricated common base plate, coupling, coupling guard, foundation bolts etc.as required. (e) Suitable cement concrete foundation duly plastered and with anti vibration pads., 450 lpm at 35 m Head (DSR -18.4.2) |
| 210 | Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required. (for terrace booster pump) (DSR -18.22) |
| 211 | Providing & fixing of start/stop push buttons including complete connection etc. as required. (for terrace booster pump) (NSR) |
| 212 | Providing and fixing in position the industrial type pressuregauges with gun metal / brass valves complete as required (for terrace booster pump) (DSR-16.8) |
| 213 | Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required, 150 mm dia. (DSR -18.11.6) |
| 214 | 100 mm dia. (DSR -18.11.5) |
| 215 | Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required, 150 mm dia. (DSR -18.14.7) |
| 216 | 100 mm dia. (DSR -18.14.5) |
| 217 | Providing, laying, testing & commissioning of \"C\" class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : (80 mm nominal bore (DSR -18.7.6) |
| 218 | 100 mm nominal bore (DSR -18.7.7) |
| 219 | 150 mm nominal bore (DSR -18.7.8) |
| 220 | Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required Single headed Gunmetal (DSR -18.9.1) |
| 221 | Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585, 20 mm nominal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the equipmets on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket., 40 m (DSR -18.17.2) |
| 222 | Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required , Gun metal (DSR -18.16.1) |
| 223 | Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required , Gun metal (DSR -18.18.1) |
| 224 | Providing and fixing standard fire mans axe with heavy duty insulated rubber handle. (NSR) |
| 225 | Providing of FHC Door made of 16 gauge MS Sheet with frame of size 105x70mm complete door and frame assembly including all hardwares (Concealed Flush handle,Allen Key Lock, MS Hinges, 5mm Thick Float glass) & accesories . The door to be painted with fire resistance paint. The scope shall also include the painting of the frame with the same paint as the shutter or complete as per direction of Engineer-in-charge.(Approx. size of door: 900mm Wide & 1500mm Height) (NSR) |
| 226 | Supplying and fixing orifice plate made out of 6 mm thick stainless steel (Grade 304) with orifice of required size to be fitted between flange & landing valve of external and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg/cm2 complete as required. (DSR -18.13) |
| 227 | Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and paintingwith synthetic enamel paint of approved shade as required. (DSR -18.2) |
| 228 | Supply and fixing of C02 type fire extinguisher 4.5 kg. capacity (ISI Marked IS : 2878 & TAC approved) complete with initial charge and wall bracket, along with supply of all materials and labour for proper completion of work. (NSR) |
| 229 | Supply and fixing of fire extinguisher, ABC Type 6.00 kg. capacity (ISI Marked IS : 15683 & TAC approved) complete with initial charge and wall bracket, along with supply of all materials and labour for proper completion of work. (NSR) |
| 230 | Providing and fixing Fire related signages printed on photoluminescent U1000 aluminium sheet of 1.0 mm (+-10%) containing Lumigen II as base chemical, covered under UV stablized coating and of appropriate size including fixing on wall, door, ceiling etc. with proper clamps, hangers, cleats, anchor fasteners etc. complete in all respects as directed by Engineer-in-charge. (NSR) |
| 231 | Fabricating & Supply, installing, testing and commissioning of sheet steel clad floor mounting control panel having suitable size for control of 1 nos. booster pumps 9.3 KW/12.5HP each having suitable incoming MCCB, incoming voltmeter with selector switch and fuses. Star delta starter with hand reset overload cum single phase preventor type relay, Ammeters to read current in any one phase, alarm with reset push button which will automatically reset for the next cycle. (As per the Technical Specifications) (At Terrace floor) (NSR) |
| 232 | Supplying, installation, testing and commissioning of micro processor based intelligent addressable main fire alarm panel, central processing unit with the following loop modules and capable of supporting not less than 240 devices (including detectors) and minimum 120 detectors per loop and loop length up to 2 km, network communication card, minimum 320 character graphics/ LCD display with touch screen or other keypad and minimum 4000 events history log in the non volatile memory (EPROM), power supply unit (230± 5% V, 50 hz), 48 hrs back-up with 24 volt sealed maintenance free batteries with automatic charger. The panel shall have facility to connect printer to printout log and facility to have seamless integration with analog/digital voice evacuation system (which is part of the schedule of work under SH: PA System) and shall be complete with all accessories . The panel shall be compatible for IBMS system with open protocol BACnet/ Modbus over IP complete as per specifications., Two Loop Panel. (DSR -17.2.1.2) |
| 233 | Supplying, installation, testing & commissioning of centralgraphical fire alarm management system to centrally monitorand operate the fire alarm system complete as required. (DSR -17.2.2) |
| 234 | Supplying, installation, testing & commissioning of intelligent analog addressable photothermal detector complete with mounting base complete as required. (DSR -17.2.4) |
| 235 | Supplying, installation, testing & commissioning of response indicator on surface/recessed MS Box having two LED, metallic cover complete with all connections etc as required. (DSR -17.2.5) |
| 236 | Supplying, installation, testing & commissioning of addressable manual call point complete as required. (DSR -17.2.14) |
| 237 | Supplying, installation, testing & commisssioning of intelligent addressable programmable sounder complete as required. (DSR -17.2.6) |
| 238 | Supplying, installation, testing & commissioning of fault isolator complete with base as required. (DSR -17.2.7) |
| 239 | Supplying, installation, testing & commissioning of fire fighter telephone handset complete as required. (DSR -17.2.17) |
| 240 | Supplying, installation, testing & commissioning of fire fighter phone jack complete as required. (DSR -17.2.19) |
| 241 | Supplying, installation, testing & commissioning of addressable fire control module complete as required. (DSR -17.2.10) |
| 242 | Supplying, installation, testing & commissioning of intelligent addressable thermal detector with rate of rise cum fixed tempreature thermistor complete with base as required. (DSR -17.2.9) |
| 243 | Supplying, installation, testing & commissioning of addressable beam detector with short circuit isolator (inbuilt or seperate) complete with emitter and receiver including connections with remote test features etc complete as required. (DSR -17.2.12) |
| 244 | Supplying, installation, testing & commissioning of intelligentinterface unit BACnet/ Modbus protocol i.e. supplyingcommunication links between building management systemand fire alarm control panel complete as required. (DSR -17.2.18) |
| 245 | Supplying, Installation, Testing & Commissioning of Modular type Variable Refrigerant Flow/Variable Refrigerant Volume air cooled Outdoor units suitable for cooling/heating having 100% hermetically sealed inverter type twin Rotary/Scroll Compressor(s),minimum two compressors (with individual separate PCB) for above 14HP modules, microprocessor based Controller, top discharge type condensing unit(s), with R-410-A Refrigerant or equivalent, vibration Isolators with suitable foundation etc. complete as required. To have better efficiency condenser fan shall be capable to operate at different speed with respect to load.The unit shall deliver the rated capacity and in confirmation as per IS 18728:2024 and CPWD Specifications and work even at 50°C ambient temperature without tripping. The system shall be able to deliver 100% of the rated capacity upto 39 °C. The unit shall be suitable to work on 400V +/- 10%, 3 Phase, 50Hz AC power supply and BMS compatible. The unit shall be filled with first charge of the refrigerant and ready for use as required. The condenser should be coated with a hydrophilic film to prevent water accumulation on the surface of the heat exchanger, enhance water dispersion, and reduce the risk of degradation, thereby improving overall performance and durability. The Indian Seasonal Energy Efficiency Ratio (ISEER) of the unit shall be as per Energy Conservation and Sustainable Building Code (ECSBC) 2024 as below and complete as per CPWD specification, connections, inter connections etc. as required. (For capacity <40 kWr ISEER 7.4, Capacity > 40 and <70 ISEER 7.5, Capacity > 70 ISEER 7.6 for Super ECSBC Building) For Cooling or Heating or Both, 6 HP to 8 HP (DSR -31.3.1) |
| 246 | 10 HP to 12 HP (DSR -31.3.2) |
| 247 | 14 HP to 22 HP (DSR -31.3.3) |
| 248 | Supplying, Installation, Testing and Commissioning of following minimum capacity Double way VRV/VRF Cassette Type Indoor ceiling mounted unit equipped with synthetic washable media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX Copper coil, electronic expansion valve, outer cabinet, drain pump, grill, necessary supports, vibration Isolation, Corded remote control etc., suitable for operation on single phase 230 V ± 10%, 50Hz AC supply, complete, as required. The Indoor units must shut down upon receiving a singal from the BMS System/Fire Singnals. The cooling capacity of indoor unit will be at air inlet conditions of 27 0C DB and 19 0C WB temperature. (Make will be same as of Outdoor) , 2.0 TR (DSR -31.7.3) |
| 249 | Supplying, Installation, Testing and Commissioning of following minimum capacity and external static pressure VRF/VRV ceiling mounted high ductable type Indoor unit equipped with washable synthetic media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX copper coil, electronic expansion valve, corded remote control, outer cabinet, vibration Isolators, drain pan, drain pump, other necessary supports etc., suitable for operation on single phase AC supply 230 V ± 10%, 50 Hz complete as required. The Indoor units must shut down upon receiving a singal from the BMS System/Fire Singnals. The cooling capacity of indoor unit will be at air inlet conditions of 27 0C DB and 19 0C WB temperature. (Make will be same as of Outdoor) , 5.5 TR (DSR -31.12.2) |
| 250 | 6.6 TR (DSR -31.12.3) |
| 251 | 8.0 TR (DSR -31.12.4) |
| 252 | Supplying, Installation, Testing and Commissioning of Y/T/Multi Joints. Joints shall be of same Original Equipment Manufacturer (OEM) make as of ODUs and IDUs (DSR -31.13), Indoor Units (DSR -31.13.1) |
| 253 | Outdoor Multi Joint (DSR -31.13.2) |
| 254 | Supplying, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of 19 mm thick insulation as given below for Suction and Liquid lines, all accessories as per specifications etc. as required , 6.4 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm (DSR -31.14.1) |
| 255 | 9.5 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm (DSR -31.14.2) |
| 256 | 12.7 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm (DSR -31.14.3) |
| 257 | 25.4 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm (DSR -31.14.7) |
| 258 | 28.58 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm (DSR -31.14.8) |
| 259 | 41.27 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm (DSR -31.14.12) |
| 260 | Providing and fixing rigid PVC piping complete with fittings, supports as per HITACHI STD.& specifications and duly insulated with 6 mm thick closed cell nitrile rubber insulation. Make:- Finolex,Supreme, Kissan ,Astral, or Hitachi/L G Approved Only, 32 mm dia (NSR) |
| 261 | 25 mm dia (NSR) |
| 262 | Outdoor unit stand (NSR) |
| 263 | Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required., 2 Pair (DSR - 1.18.2) |
| 264 | Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required. , 1 run of cable (DSR -1.53.1) |
| 265 | Providing and fixing HT danger notice plate 250 mm x 200 mm made of mild steel at least 2mm thick & vitreous enamelled white on both sides and with inscription in signal red colour on front side as required. (DSR -2.22) |
| 266 | Constructing masonry Chamber 90x90x100 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep (inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ), i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design :, With common burnt clay F.P.S.(non modular) bricks of class designation 7.5 (DSR -18.34.1) |
| 267 | Supply and fixing of Single light Wall Bracket on matching M.D.F.E.G. Board base etc.Complete in all respect. CAT. - AAA (NSR ) |
| 268 | Cost of Architectural Interior Lighting as per drawing and make approved approved by Architect in charge (NSR ) |
| 269 | P& F Full Ht\" Hanging Display of MS pipe of 10mm with the finish of Physical Vapour Decomposed Coating with bending and welding design as per drawing and approval of architect in charge. (C-11) (NSR ) |
| 270 | P&F for Rooms Interior as per drawing received from Architect in charge, inluding furniture, HVAC, curtains, rugs, key management system etc. (NSR ) |
| 271 | Providing and fixing in position at required location, GRC (Glass reinforced concrete) bush box Planter of height 1.5m, 1.50m length,width 500mm as per Architect\"s Design and as directed by project architect with all leads and lifts etc. complete in toto. (NSR ) |
| 272 | Supply and installation of CARA Bench, measuring L74 x W35 x H42 cm, is constructed from a unique polymer blend that mimics the appearance of stone while offering lightweight durability. This material is 100% recyclable and features UV stabilization to prevent color fading, making it ideal for both indoor and outdoor applications. The bench combines aesthetic appeal with practical functionality, ensuring long-lasting performance and environmental sustainability. (NSR ) |
| 273 | Supply, Installation and Commissioning of Kitchen setup, architectrual lighting and furninture customisation in desired material, shade and finish including burners, SS baskets, SS Cabinets etc. complete as per drawing and design approved and recived from Architect in charge ( Complete In all respect). (NSR ) |
| 274 | Supply, Installation and Commissioning of architecterual lighting customised in desired material, shade and finish including track, cove, breacket, wall light etc. complete as per drawing and design approved and received from Architect in charge including the cost of shop drawing prepration and sampling ( Complete In all respect). (NSR ) |
| 275 | Supply and installation of OVALE Lamp features a translucent white LED and stands 2 meters tall. It is constructed from a unique polymer blend with a black matte metal base, ensuring both durability and a modern aesthetic. The lamp includes a remote control for convenient operation and offers both warm white and cool white lighting options. Suitable for both indoor and outdoor use, it is designed as a floor lamp with a heavy base for stability.( Complete In all respect). (NSR ) |
| 276 | Furniture as approved by Architect in charge.( Complete In all respect). |
| 277 | SITC of Twin Room Cottage, designed as a hybrid using Light Gauge Steel Framing (LGSF) techNoslogy, imported from Australia, incorporating mild steel load-bearing sections fabricated using CNC machines. The structure is engineered to withstand wind speeds of up to 180 kmph and is suitable for seismic zone IV. The RCC plinth is to be constructed as per the structural drawings, over which the prefabricated steel superstructure will be installed. The cost is inclusive of strcutural design for the substracture base on the recieved site inputs from Archiect and Structural incharge as per the basis of Indian codes and std. The construction fo the RCC upto plinth is inclusive along with the peripheral deck of min 1.2M wide with bamboowood decking. The external walls of the cottage are clad with thermo pine wood planks, providing both aesthetic warmth and weather resistance. These claddings are pre-treated and coated with weatherproof oils to ensure longevity and are fixed over OSB (Oriented Strand Board) sheets of 10 mm thickness. The structure is further wrapped with waterproof and termite-resistant OSB panels from both inside and outside for additional protection.The roof is constructed using asphalt shingles manufactured by TechNosNICOL Corporation, supported over a lightweight framing system. These shingles offer a 50-year warranty and provide excellent resistance against heat and water ingress.All internal walls and ceilings are finished with gypsum board over OSB panels and painted in the client’s choice of colour. Bathroom walls are tiled with ceramic tiles from Kajaria, and the toilets are fitted with high-quality sanitaryware from Kohler and Jaguar, including WC, washbasins, faucets, and other essential fixtures. All internal plumbing lines are made of CPVC/UPVC. The flooring in rooms is finished with indoor-grade wooden laminate flooring from Greenply, offering multiple colour options. ( Complete In all respect). \"Toilets are laid with vitrified tiles, and the external deck area is made of thermo pine wood finished with weather-protective coatings. Doors are made of laminated flush doors, and windows/sliding doors are of UPVC sections fitted with 5 mm toughened glass. Options for double glazing units and mosquito mesh are available at extra cost. Skylights can also be provided in the roof structure if required. Electrical fittings include internal wiring with R R Kabel and fittings like switches/sockets of Legrand make and LED lights of Jaquar/Philips. Provisions for air-conditioning pipelines are embedded within wall layouts. \" Decks are finished with 90×90 mm thermo pine balusters and 10 mm thick toughened glass inserts, with handrails made of 140×26 mm thermo pine sections, providing a secure yet transparent enclosure for the front deck areas. The structure includes two identical rooms of 10\"-9\" × 13\"-6\", each with an attached toilet (10\"-9\" × 5\"-0\") and a front-facing 11\"-0\" × 6\"-0\" deck space. The total covered area of the cottage is 592 square feet. All structural and finishing works shall be executed in compliance with the direction of the Engineer-in-Charge, adhering to the approved architectural and technical drawings. The cost of substructure is inclusive. The cost is inclusive of preparation of shop drawing and sample approval as per Architect in charge. The above mentioned finishes, makes of all items are subject to final approval by sample procurement and submission from any leading vendor to the Architect in charge. Cost of G+1 Prefab Cottages in group of 4 |
| 278 | SITC of G+1 Prefabricated Twin Room Cottages, designed as a hybrid prefabricated structure using Light Gauge Steel Framing (LGSF) techNoslogy, with primary structural sections imported from Australia and secondary mild steel load-bearing members precision-fabricated using CNC machines. The complete superstructure is engineered to withstand basic wind speeds up to 180 kmph and is suitable for Seismic Zone IV, fully complying with relevant Indian Codes and Standards.The RCC substructure up to plinth level, including foundations, plinth beams, and pedestals, shall be constructed as per approved structural drawings. Over this, the prefabricated steel superstructure (G+1) shall be installed. The cost is inclusive of structural design for the superstructure and substructure, based on site inputs received from the Architect and Structural In-Charge. Construction of RCC up to plinth level is included, along with a peripheral deck of minimum 1.2 m width at the ground floor level, finished with thermo pine / bamboo wood decking with weather-protective coatings.Superstructure & Envelope The external walls of the cottages are clad with thermo pine wood planks, providing aesthetic warmth, durability, and resistance to harsh weather conditions. The timber cladding is factory-treated and coated with high-performance exterior oils and is fixed over 10 mm thick OSB (Oriented Strand Board) sheathing. The entire structure is further wrapped with waterproof and termite-resistant OSB panels, provided both internally and externally, ensuring enhanced durability and thermal performance. The roof system is constructed using asphalt shingles manufactured by TechNosNICOL Corporation, installed over a lightweight steel framing system. These shingles carry a 50-year manufacturer warranty and provide excellent resistance against heat, rain, and water ingress. Provision for skylights within the roof structure can be incorporated if required, at an additional cost.The structure is further wrapped with waterproof and termite-resistant OSB panels from both inside and outside for additional protection.The roof is constructed using asphalt shingles manufactured by TechNosNICOL Corporation, supported over a lightweight framing system. These shingles offer a 50-year warranty and provide excellent resistance against heat and water ingress. All internal walls and ceilings are finished with gypsum board over OSB panels and painted in the client’s choice of colour. Bathroom walls are tiled with ceramic tiles from Kajaria, and the toilets are fitted with high-quality sanitaryware from Kohler and Jaguar, including WC, washbasins, faucets, and other essential fixtures. All internal plumbing lines are made of CPVC/UPVC. The flooring in rooms is finished with indoor-grade wooden laminate flooring from Greenply, offering multiple colour options. ( Complete In all respect). \"First Floor Construction & Deck The first floor is constructed using a prefabricated lightweight floor framing system, designed for residential live loads as per Indian Standards. The floor assembly includes structural steel joists, OSB sheathing, acoustic insulation, and finished flooring. A front-facing deck slab at first-floor level is provided for each cottage unit, supported on the LGSF/MS structure and designed for outdoor usage. The deck flooring is finished with thermo pine wood planks treated with weather-resistant coatings. Deck safety railings comprise 90 × 90 mm thermo pine balusters, 10 mm thick toughened glass panels, and handrails of 140 × 26 mm thermo pine sections, ensuring safety while maintaining visual transparency. Staircase Access to the first floor is provided through a custom-designed external metal staircase, fabricated from hot-dip galvanized mild steel sections. The staircase includes anti-slip treads, landings, and safety railings, finished with corrosion-resistant paint systems suitable for outdoor conditions. The staircase design is fully integrated with the architectural intent and structural system.\" \"Toilets are laid with vitrified tiles, and the external deck area is made of thermo pine wood finished with weather-protective coatings. Doors are made of laminated flush doors, and windows/sliding doors are of UPVC sections fitted with 5 mm toughened glass. Options for double glazing units and mosquito mesh are available at extra cost. Skylights can also be provided in the roof structure if required. Electrical fittings include internal wiring with R R Kabel and fittings like switches/sockets of Legrand make and LED lights of Jaquar/Philips. Provisions for air-conditioning pipelines are embedded within wall layouts. INlducing electifcal fitures too \" Decks are finished with 90×90 mm thermo pine balusters and 10 mm thick toughened glass inserts, with handrails made of 140×26 mm thermo pine sections, providing a secure yet transparent enclosure for the front deck areas. The structure includes two identical rooms of 10\"-9\" × 13\"-6\", each with an attached toilet (10\"-9\" × 5\"-0\") and a front-facing 11\"-0\" × 6\"-0\" deck space. The total covered area of the cottage is 592 square feet. All structural and finishing works shall be executed in compliance with the direction of the Engineer-in-Charge, adhering to the approved architectural and technical drawings. The cost of substructure is inclusive The cost is inclusive of preparation of shop drawing and sample approval as per Architect in charge. The above mentioned finishes, makes of all items are subject to final approval by sample procurement and submission from any leading vendor to the Architect in charge. Cost of Prefab admin, Cafeteria having backhouse facilites and a swimming pool at top |
| 279 | SITC of G+1 Prefabricated Twin Room Cottages, designed as a hybrid prefabricated structure using Light Gauge Steel Framing (LGSF) techNoslogy, with primary structural sections imported from Australia and secondary mild steel load-bearing members precision-fabricated SITC of Prefabricated Admin and Cafeteria Building, designed as a hybrid structure using Light Gauge Steel Framing (LGSF) techNoslogy, imported from Australia, incorporating mild steel load-bearing sections fabricated using CNC machines. The structure is engineered to withstand wind speeds of up to 180 kmph and is suitable for Seismic Zone IV. The RCC substructure up to plinth level, including foundations, pedestals, and plinth beams, shall be constructed as per approved structural drawings, over which the prefabricated steel superstructure shall be installed. The cost is inclusive of structural design for the substructure, based on site inputs received from the Architect and Structural In-Charge, designed as per Indian Codes and Standards. Construction of RCC up to plinth level is inclusive. Superstructure, Walls & Cladding The external walls of the building are clad with thermo pine wood planks, providing aesthetic warmth and weather resistance. The claddings are pre-treated and coated with weatherproof oils and are fixed over 10 mm thick OSB (Oriented Strand Board) sheets. The structure is further wrapped with waterproof and termite-resistant OSB panels from both inside and outside for additional protection and durability. Internal partitions are formed using the same LGSF system, sheathed with OSB boards and finished with gypsum boards. The roof system is constructed using asphalt shingles manufactured by TechNosNICOL Corporation, installed over a lightweight steel framing system. These shingles carry a 50-year manufacturer warranty and provide excellent resistance against heat, rain, and water ingress. Provision for skylights within the roof structure can be incorporated if required, at an additional cost.The structure is further wrapped with waterproof and termite-resistant OSB panels from both inside and outside for additional protection.The roof is constructed using asphalt shingles manufactured by TechNosNICOL Corporation, supported over a lightweight framing system. These shingles offer a 50-year warranty and provide excellent resistance against heat and water ingress. All internal walls and ceilings are finished with gypsum board over OSB panels and painted in the client’s choice of colour. Bathroom walls are tiled with ceramic tiles from Kajaria, and the toilets are fitted with high-quality sanitaryware from Kohler and Jaguar, including WC, washbasins, faucets, and other essential fixtures. All internal plumbing lines are made of CPVC/UPVC. The flooring in rooms is finished with indoor-grade wooden laminate flooring from Greenply, offering multiple colour options. ( Complete In all respect). \"Roof & Rooftop Swimming Pool The roof structure is constructed using a lightweight framing system over LGSF members. The rooftop swimming pool is provided above the superstructure and shall be constructed as a structural RCC pool, designed for water load, live load, and safety as per relevant Indian Standards. The pool includes RCC base slab, side walls, waterproofing treatment, and finished pool surfaces. Adequate structural strengthening and load transfer systems are incorporated within the prefabricated structure to safely support the rooftop swimming pool. Pool edge coping, internal finishes, and waterproofing systems shall be executed as per approved drawings and specifications. Pool equipment, filtration systems, and accessories are excluded unless specifically mentioned. Internal Finishes – Admin & Cafeteria Areas All internal walls and ceilings are finished with gypsum boards over OSB panels and painted in the client’s choice of colour. Flooring in admin and cafeteria areas is finished with vitrified tiles, suitable for heavy footfall. Cafeteria Back-of-House Facilities The cafeteria includes dedicated back-of-house (BOH) areas comprising kitchen, food preparation zone, washing area, store, and staff utility spaces. Walls in kitchen and washing areas are finished with ceramic tiles, and floors are laid with anti-skid vitrified tiles. All plumbing lines are executed using CPVC/UPVC piping systems, suitable for commercial usage. Proper provisions for exhaust, ventilation, and service shafts are integrated within the wall and ceiling layouts.\" \"Toilets are laid with vitrified tiles, and the external deck area is made of thermo pine wood finished with weather-protective coatings. Doors are made of laminated flush doors, and windows/sliding doors are of UPVC sections fitted with 5 mm toughened glass. Options for double glazing units and mosquito mesh are available at extra cost. Skylights can also be provided in the roof structure if required. Electrical fittings include internal wiring with R R Kabel and fittings like switches/sockets of Legrand make and LED lights of Jaquar/Philips. Provisions for air-conditioning pipelines are embedded within wall layouts. INlducing electifcal fitures too \" Decks are finished with 90×90 mm thermo pine balusters and 10 mm thick toughened glass inserts, with handrails made of 140×26 mm thermo pine sections, providing a secure yet transparent enclosure for the front deck areas. The structure includes two identical rooms of 10\"-9\" × 13\"-6\", each with an attached toilet (10\"-9\" × 5\"-0\") and a front-facing 11\"-0\" × 6\"-0\" deck space. The total covered area of the cottage is 592 square feet. All structural and finishing works shall be executed in compliance with the direction of the Engineer-in-Charge, adhering to the approved architectural and technical drawings. The cost of substructure is inclusive The cost is inclusive of preparation of shop drawing and sample approval as per Architect in charge. The above mentioned finishes, makes of all items are subject to final approval by sample procurement and submission from any leading vendor to the Architect in charge. Cost of Multipurpose Hall PEB of min area of 950 SQM inlduing ht ePEB strcture, finishes as per Architect in cahrge |
| 280 | SITC of G+1 Prefabricated Twin Room Cottages, designed as a hybrid prefabricated structure using Light Gauge Steel Framing (LGSF) techNoslogy, with primary structural sections imported from Australia and secondary mild steel load-bearing members precision-fabricated SITC of Prefabricated Admin and Cafeteria Building, designed as a hybrid structure using Light Gauge Steel Framing (LGSF) techNoslogy, imported from Australia, incorporating mild steel load-bearing sections fabricated using CNC machines. The structure is engineered to withstand wind speeds of up to 180 kmph and is suitable for Seismic Zone IV. The RCC substructure up to plinth level, including foundations, pedestals, and plinth beams, shall be constructed as per approved structural drawings, over which the prefabricated steel superstructure shall be installed. The cost is inclusive of structural design for the substructure, based on site inputs received from the Architect and Structural In-Charge, designed as per Indian Codes and Standards. Construction of RCC up to plinth level is inclusive. Superstructure, Walls & Cladding The external walls of the building are clad with thermo pine wood planks, providing aesthetic warmth and weather resistance. The claddings are pre-treated and coated with weatherproof oils and are fixed over 10 mm thick OSB (Oriented Strand Board) sheets. The structure is further wrapped with waterproof and termite-resistant OSB panels from both inside and outside for additional protection and durability. Internal partitions are formed using the same LGSF system, sheathed with OSB boards and finished with gypsum boards. The roof system is constructed using asphalt shingles manufactured by TechNosNICOL Corporation, installed over a lightweight steel framing system. These shingles carry a 50-year manufacturer warranty and provide excellent resistance against heat, rain, and water ingress. Provision for skylights within the roof structure can be incorporated if required, at an additional cost.The structure is further wrapped with waterproof and termite-resistant OSB panels from both inside and outside for additional protection.The roof is constructed using asphalt shingles manufactured by TechNosNICOL Corporation, supported over a lightweight framing system. These shingles offer a 50-year warranty and provide excellent resistance against heat and water ingress. All internal walls and ceilings are finished with gypsum board over OSB panels and painted in the client’s choice of colour. Bathroom walls are tiled with ceramic tiles from Kajaria, and the toilets are fitted with high-quality sanitaryware from Kohler and Jaguar, including WC, washbasins, faucets, and other essential fixtures. All internal plumbing lines are made of CPVC/UPVC. The flooring in rooms is finished with indoor-grade wooden laminate flooring from Greenply, offering multiple colour options. ( Complete In all respect). Decks are finished with 90×90 mm thermo pine balusters and 10 mm thick toughened glass inserts, with handrails made of 140×26 mm thermo pine sections, providing a secure yet transparent enclosure for the front deck areas. The structure includes two identical rooms of 10\"-9\" × 13\"-6\", each with an attached toilet (10\"-9\" × 5\"-0\") and a front-facing 11\"-0\" × 6\"-0\" deck space. The total covered area of the cottage is 592 square feet. All structural and finishing works shall be executed in compliance with the direction of the Engineer-in-Charge, adhering to the approved architectural and technical drawings. The cost of substructure is inclusive The cost is inclusive of preparation of shop drawing and sample approval as per Architect in charge. The above mentioned finishes, makes of all items are subject to final approval by sample procurement and submission from any leading vendor to the Architect in charge. (makes Loomcraft/ or equivalent) \"Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: (a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. (b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. (c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge. (d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep (e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. “All above operations to be done in order and as directed and specified by the Engineer-in-Charge”:With average thickness of 120 mm and minimum thickness at khurra as 65 mm\" |
| 281 | Float glass panes 4 mm thick glass pane (weight not less than 10kg/sqm). (DSR -9.7.7.1) |
| 282 | Supply of DLP Laser projector, Brightness: Min 19000 Lumens, Native resolution: WUXGA (1920 x1200) or more. Input Resolution support : 4K or better, Contrast: 100000:1 or more; Sealed core optics, Brightness Uniformity: 90% or more; Illumination Lifetime: 20000 Hrs or more ; Inbuitl Warping & Blending; Stereoscopic 3D support for future 3D shows; Inputs: 2 x HDMI 2.0, DP 1.2, HDbaseT,VGA. Operating temperature: 0-50 degC . Compact & Light Weight: 50Kgs or less. Should be supplied with appropriat long throw lens as per site requirement. TAA certification required ( Complete In All respect ) (NSR) |
| 283 | Supply of Smart light weight outdoor projector enclosure suitable for Marine environment made of Aluminum with Aluminum wielding. Complete with:Build to meet minimum IP64 weatherization standards.Anti-reflecting tempered glass window with 94% transparency provided for an uninterrupted projection.Hydrophobic filter for salt fog filtering.Powerful AC fan for efficient cooling with positive pressure for ultimate projector protection. Fan circulation to automatically start even during day time if inside temperature goes above 35 deg Cel. Sensor based Humidity and temperature control automation to provides complete climate control inside the enclosure automatically. Enclorure unit to be Insulated with non fibrous, non toxic Cross linked polyethylene sheets with min. 19mm thicknessComplete unit to be powder coated and insulated for heat protection. Power distribution sockets 16/6 Amps and industrial plug 32A.( Complete In All respect ) (NSR) |
| 284 | Designing,Fixing and intallation of projectors,with suitable MS base plate of 10mm, clamps, grouting material, painting and other accessories.( Complete In All respect ) (NSR) |
| 285 | Supply of Media Server with associated software license and hardware . The display server should have 4 DP 1.4v outputs with each channel supporting 4k@60, 4.4.4The hardware should have 16GB RAM System memory, min. 1TB High Performance SSD Drive Storage. The hardware should have dedicated 6GB GPU and 1GBP/S ethernet port with 2 USB3 ports,3.5 mm stereo output jack and should support genlock, geometry correction, edge blending, color correction and 2D/3D mapping. The OS for the server should be Windows 10 enterprise embedded with quick OS recovery built-in.( Complete In All respect ) (NSR) |
| 286 | Supply of Show Control software complete with necessary software and hardware interface including lifetime license and accessories.( Complete In All respect ) (NSR) |
| 287 | Supply of All-Weather Loudspeaker with 15\" LF ,Frequency Range (-10 dB): 35 Hz – 20 kHz, Frequency Response (±3 dB): 55 Hz – 19 kHz ,Coverage Pattern: 90° x 50°, Long-Term System Power Rating: 600 W (2400 W peak), Sensitivity (2.83V @ 1m): 100 dB ,Maximum SPL: 128 dB (peaks of 134 dB), Crossover Frequency: 1.2 kHz, Nosminal Impedance: 8 ohms ,Transformer Taps: 70V: 400W, 200W, 100W. 100V: 400W, 200 Environmental: IP55 as per direction given bt engineer in charge.( Complete In All respect ) (NSR) |
| 288 | Supply of Subwoofer Dual 18 Inches of Frequency Range (-10dB): 28 Hz – 1 kHz, Frequency Response (±3 dB): 35 Hz – 1 kHz, System Power Rating: 1600 W (6400 W peak), Sensitivity 102 dB , Maximum SPL (1m) 136dB, 142 dB Peak, Nosminal Impedance 4 ohms , IPX3, 4 Inches Voice Coil. (NSR) |
| 289 | Supply, of Two-way Small Format high SPL IP55 rated (as per IEC 60529) all weather surface mount loudspeaker. The louspeaker shall meet the following performance criteria: Frequency Range (-10 dB) of 80 Hz - 20 kHz or better; Nosminal Dispersion : 120°H x 120°V; Power handling of 200cW or more; Sensitivity : 94 dB; Max SPL : 123dB Peak; Nosminal impedence of 8 ohms. The loudspeaker system shall be comprised of a Powder-coated finish stainless steel grille with Two-part spray polyurea coating Enclosure; Single 8-inch woofer; Single 2-inch voice coil high-frequency compression driver; U bracket. ( Complete In All respect ) (NSR) |
| 290 | Supply of Multichannel Digital Network Based Power Amplifier with Power output 4 x 1250W @ 4 Ohms / 8 Ohms, Four-channel Audio amplifier, 4x 1250W at 4 and 8 Ohm, 70Vrms and100Vrms output on all Four channels, THD (at full rated power, 20Hz - 20kHz) =0.35%, Cooling Continuously variable speed forced air, Voltage Gain Max level= 34dB, Audio Digital channel bus compatibility up to 8 channel,bridgeable channels - even in 100Vrms mode, 2 digital audio bus RJ45 port, 1 Ethernet RJ45 port for monitoring and configuration, Should have Limiters , Input/output EQ , Delay ,Matrix Mixer ,Speaker Line impedance Monitoring, Damping Factor (20 Hz to 100 Hz) : >1500 (NSR) |
| 291 | Supply, installation, testing & Comissioning of Multichannel Digital Network Based Power Amplifier with Power output 8 x 600W @ 4 Ohms / 8 Ohms, Four-channel Audio amplifier, 8x 600W at 4 and 8 Ohm, 70Vrms and100Vrms output on all Four channels, THD (at full rated power, 20Hz - 20kHz) =0.35%, Cooling Continuously variable speed forced air, Voltage Gain Max level= 34dB, Audio Digital channel bus compatibility up to 8 channel,bridgeable channels - even in 100Vrms mode, 2 digital audio bus RJ45 port, 1 Ethernet RJ45 port for monitoring and configuration, Should have Limiters , Input/output EQ , Delay ,Matrix Mixer ,Speaker Line impedance Monitoring, Damping Factor (20 Hz to 100 Hz) : >1500 ( Complete In All respect ) (NSR) |
| 292 | Supply of 12 x 8 Networked Digital Signal Processor With AEC , Should have 12 floating AEC in group of 4 Ch SITC of DSP with 12 inputs and 8 outputs, 12 Control Inputs and 6 Logic Outputs for GPIO Integration, 48V phantom power on all analog inputs, THD: <0.01% 20Hz to 20KHz, +10dBu output, Crosstalk: <-75dB, Open architecture software configurable, Separate logic processing power ,2 digital audio bus RJ 45 Port , 1 Ethernet port for Monitoring and configuration , Capable to handle +5V unloaded logic output voltage ,Should have speech filter engine , Capable to control 3rd party devices with TCP IP and RS 232 , Should have 1Nos of RS 232 port for integration with control System, Should have Bi-Directional Locate Functionality ,Should have 48 or more digital audio Channel Bus, Should have monitoring LED for COM, STAT, ERR and PWR ( Complete In All respect ) (NSR) |
| 293 | Screen Estblishing & Content Generation, Designing, Storyboarding, Historian/ Project Conservationist onboarding, Direction and Graphics, ArtisticDirection, research, script, translation, dramatization, Visualizing the content, creating 2D,3D animation, CGI, video shoot including artist, laser animation,Art component (ifany),Programming/integration of show with content,effect complete etc.as reqd.The work includes collection of required information & relevant data, development of content for illumination show in consultation with client and making changes as per the observations / requirements.Content should be of 15mins. (NSR) |
| 294 | Supply of Small Business 24 port Gigabit switch and 2 x Mini GBIC fiber uplinks. Standards:-IEEE 802.3, 802.3u, 802.3x, 802.3ab. Cabling Type:-Category 5 and multi-mode fiber. Power:-100-127VAC/200-240VAC, 1.0A/0.5A, 50-60 Hz. Operating Temperature:-32 to 104ºF (0 to 40ºC). (NSR) |
| 295 | Supply of Equipment Rack - 19 \" , 27U standard Rack with all required accessories. Earthing community kit, mounting bracket, cable manager, support angle, equipment shelf, mounting hardware, fan housing units etc, Ventilated top and bottom covers with attractive styling. It has Removable side panels with slam latches for easy access. (NSR) |
| 296 | Installation, Testing & Comissioning of Audio system, Projector mounting,mapping, Alignment, blending, Projector & audio system Poles,complete project other items installation (NSR) |
| 297 | Supply , laying of all conduits, Audio, Video cables, TP/Fibreoptic cables, Fibre Optic HDMI cables/ TX-RX set for projectors -connectors & accessories as required form complete installation (NSR) |
| 298 | Supply, Fabrication & Installation of exterior directional sign board of size 750W X _ 1800H(Information panel) mounted on M.S. internal skeletal framework made out of M.S. box sections as detailed. All MS work should have one coat of primer and 2 | coats of Epoxy paint applied as per manufacturers instructions. The information panel shall be made out of 4mm thick Aluminium Composite Panel boxing of approved make and colour bent to curved/straight profile on both the sides as detailed. Graphic shall be printed on_ External Grade External Grade Vinyl and stuck to the main panel. The panel formed shall have overall minimum thickness of 90mm. The panel to have NLSIU Logo, Text in trilanguage, _— etc as detailed. The panel shall \" be fitted 150mm above ground level. Exposed part of the panel grouted to the foundation shall be clad with Flame finish steel grey granite, all complete as per drawings, specifications & directions of Engineer In Charge. The rate quoted shall include the cost of scaffolding, fixing and grouting if any, etc. Cost for Excavation, Concrete and_ granite cladding shall be paid separately under their respective items. (NSR) |
| 299 | Supply, Fabrication & Installation of exterior directional sign board of size 750W xX _ 1050H (Information panel) mounted on M.S. internal skeletal framework . made out of M.S. box sections as detailed. All MS work should have one coat of primer and 2 coats of Epoxy paint applied as per manufacturers instructions. The information panel shall be made out of 4mm thick Aluminium Composite Panel boxing (Di-bond / Aluco bond or approved equivalent make) of approved colour bent to curved/straight profile on both the sides as detailed in the drawing. Graphic shall be printed on External Grade Vinyl and stuck to the main panel. The panel formed shall have overall minimum thickness _ of 90mm. The panel to have : NLSIU Logo, Text in trilanguage, etc as detailed. The panel shall be fitted 150mm above pround level. Exposed part of the panel grouted to the foundation shall be clad with Flame finish steel grey granite, all complete as per drawings, specifications & directions of Engineer In Charge. The rate quoted shall include the cost of scaffolding, fixing, grouting and grouting if | any, etc.Cost for Excavation, Concrete and granite cladding shall be paid separately under their respective items. (NSR) |
| 300 | Over all Size: Height -240 inch, Width - 46 inch, Depth - 12 inch Exterior moNoslithic double sided signage fixed with the help of MS pipe frame work cladded with 3mm thick Aluminium composite panel (ACP) duly cut by CNC router with 5mm/12mm imported A- cast “Acrylite” make acrylic fixed with 040 acrylic sheet on back with exterior grade vinyl text, illumination with backlit water proof IP-68 rated LED inside for individual letter illumination complete in all respects as per design. The Foundation work with reinforcement: Foundation Size 5 ft (L) x 3ft (W) x 5ft (D) (12 mm & 10 mm dia reinforcement steel @ 150mm bothways as per approval of Engineer-in-Charge, to be used in foundation with grouting of MS base plate (16 mm thickness) with the help of 20 mm dia grouting bolt of length Nost less than 450mm. The Nosminal mix concrete of mix proportion 1:1.5:3 to be used in foundation. The MS Structure to be erected over 16mm thick MS base plate. The 2 Nos MS pipe of size 150 x 75 x 5 mm to be fixed over base plate suitably braced with MS pipe of size 150 x 75 x 5 mm in between (04 Nos: 01 Nos top, 01 Nos bottom and 02 Nos in between) . Framing of MS pipe of size 25x25x5 over existing braced structure to be made on both side and thereafter, 50x50x5 mm square pipe to be fixed on side of structure in such a way to make provision for opeing on one side for maintenance purpose . ACP sheet – 3mm ACP sheet as per color approved by Engineer-in-Charge : Both side with side coverage as per design,approved size and approved MS structure. The ACP sheet to be cut by CNC router as per exact letter size & logo and as per approval of mock-up plan. Illumination: Illumination of Nost less than 140 lumens per feet, color temperature 10,000 K with IP68 grade power supply of SAMSUNG or equivalent make. 1)Logo of approximate size 42\" x 14\" on both side. 2) 12mm solid acrylic sheet laser cut letters-\"\" 3) 5mm solid acrylic sheet laser cut letters - 4) 12mm solid acrylic sheet laser cut letters of letter size 7 5) 5mm solid acrylic sheet laser cut letters- Noste: 1) Matter on one side to be writen in Hindi font and on aNosther side in English Font. 2) Matter as per tentative lay-out given. However, before actual execution, the bidder to take prior approval of mock -up plan from Engineer-in-Charge.( Complete In All respect ) (NSR) |
| 301 | Supply, Fabrication & Installation of exterior Informatory signboard of size 450W X 450H / 450 dia mounted on 50 mm dia M.S. _ Pipe Medium (B-Class), with : one coat of primer and 2 coats of Epoxy paint applied as per manufacturers instructions as indicated. The information panel shall be made out of 4mm thick Aluminium Composite Panel _ of approved make = and colour as detailed in the drawing. Graphic shall be printed on External Grade Vinyl and stuck to : the main. panel, all complete as per drawings, specifications . & directions of Engineer In Charge. The rate quoted shall include the cost of scaffolding, fixing, sprouting and grouting if any, etc.Cost for Excavation, Concrete shall be paid separately under their respective ‘items. Top of board shall be 1950 from Finished floor level. (NSR) |
| 302 | Supply, Fabrication &| SQM Installation of cautionary signs of size as per | design made of 2mm thick Aluminium plate with Reflective External Grade Vinyl _ stickers, Fixed to surface using 3M tape, \"__ including necessary surface cleaning, all complete as per drawings, specifications & directions of Engineer In Charge. The rate quoted shall include the cost of scaffolding, fixing, etc. (NSR) Please Enable Macros to View BoQ information |
| 303 | Supply, Fabrication &| SQM Installation of cautionary signs of size as per | design made of 2mm thick Aluminium plate with Reflective External Grade Vinyl _ stickers, Fixed to surface using 3M tape, \"__ including necessary surface cleaning, all complete as per drawings, specifications & directions of Engineer In Charge. The rate quoted shall include the cost of scaffolding, fixing, etc. (NSR) Please Enable Macros to View BoQ information |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
| 4 | Click here to download tender document | Tender Documents |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2026 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
