|
| 1 | Dismantling E.P. or Anglo-Indian W.C |
| 2 | Supplying, fitting and fixing Orissa pattern water closet in white glazed vitreous chinaware of approved make in position complete excluding \"P\" or \"S\" trap (excluding cost of concrete for fixing) (i) 580 mm X 440 mm. |
| 3 | Ordinary cement concrete ( mix 1:1.5:3) with graded stone chips with (20 mm normal size) excluding shuttering and reinforcement if any, in ground floor as per relevant IS codes(ii) River Bazree. |
| 4 | Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc. initial straightening and removal of loose rust (if necessary), cutting to requisite length hooking and bending to correct shape, placing in proper position and binding with 16-gauge black annealed wire at every inter-section, complete as per drawing and direction. (a) For works in foundation, basement and upto roof of ground floor/upto 4m) (i)Tor steel/Mild steel III. Others manufacturers not specified . |
| 5 | Dismantling artificial stone flooring upto 50 mm. thick by carefully chiselling without damaging the base and removing rubbish as directed within a lead of 75 m |
| 6 | Hire and labour charges for shuttering with centering and necessary staging upto 4.0m using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slabs,beams and columns,lintels curved or straight including fitting, fixing and striking out after completion of work (upto roof of ground floor) (a) 25 mm to 30mm thick wooden shuttering as per decision and direction of the EIC. |
| 7 | Plaster (to wall ,floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course scaffolding/ staging where necessary (Ground floor) (c) 10 mm thick with 1:4 cement mortar |
| 8 | Supplying,fitting & fixing 1st quality Ceramic tiles in wall and floors to match with the existing work and 4nos of key stone(10mm)fixed with aralidiet at the back of each tile and finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles includuing roughining of concrete surface if nececcary or by synthetic adhesive and grout material etc (A) Floor With Sand Cement Mortar (1:4) 20 mm thick & 2 mm thick cement slurry at back side of tiles using cement @ 2.91 Kg/Sq.m & joint filling using white cement slurry @ 0.20kg/Sq.m.(b)Area of each tile above 0.09 Sq.m(ii) Other than Coloured decorative including white . |
| 9 | Supplying,fitting & fixing 1st quality Ceramic tiles in wall and floors to match with the existing work and 4nos of key stone(10mm)fixed with aralidiet at the back of each tile and finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles includuing roughining of concrete surface if nececcary or by synthetic adhesive and grout material etc(B)WALL with sand cement mortar(1:3) 15mm thick and 2mm thick cement slurry at back side of tiles using [email protected]/sqm and joint filling using white cement slurry @0.20kg/sq m (b) Area of each tile above 0.09 Sq.m (ii) Other than Coloured decorative including white |
| 10 | Synthetic Distemper to interior wall, ceiling with a coat of solvent based interior grade acrylic primer (as per manufacturer\"s specification) including cleaning and smoothning of surface. Two Coats |
| 11 | Supplying, fitting & fixing UPVC pipes A- Type and fittings conforming to IS:13592-1992 with all necessary clamps nails, including making holes in walls, floor etc. cutting trenches in any soil through masonry concrete structures etc if necessary and mending good damages including joining with jointing materails (Spun Yarn, Valamoid/Bitumen/M-Seal etc) complete A) UPVC Pipes: (ii) 110 mm. Dia. |
| 12 | Supplying, fitting & fixing UPVC pipes A- Type and fittings conforming to IS:13592-1992 with all necessary clamps nails, including making holes in walls, floor etc. cutting trenches in any soil through masonry concrete structures etc if necessary and mending good damages including joining with jointing materails (Spun Yarn, Valamoid/Bitumen/M Seal etc) complete B) UPVC Fittings: c) Bend 87.5 degree (ii) 110 mm. Dia |
| 13 | Supplying, fitting & fixing UPVCpipes A- Type and fittings conforming to IS:13592-1992 with all necessary clamps nails, including making holes in walls, floor etc. cutting trenches in any soil through masonry concrete structures etc if necessary and mending good damages including joining with jointing materails (Spun Yarn, Valamoid/Bitumen/M Seal etc) complete B) UPVC Fittings: a) Plain Tee(ii) 110 mm. Dia |
| 14 | Applying decorative cement based paint of approved quality after preparing the surface including scraping the same thoroughly (plastered or concrete surface) as per manufacturer\"s specification In Ground floor: (iii) Two coats. |
| 15 | Neat cement punning about 1.5 mm thick in wall dado, window sills, floors, drain etc. Note: Cement 0.152 cum per 100 sqm |
| 16 | Supply of UPVC pipes (B-Type) & fittings conforming to I.S. 13592 1992, (B) fitting (b)110/110 S trap. |
| 17 | Supplying, fitting and fixing G.I. pipes of TATA make with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, ipple, longscrew, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting pipes, making threads, fitting, fixing etc. complete in all respect including cost of all necessary fitttings as required, jointing materials and two coats of painting with approved paint in any position above ground (Payment will be made on the centre line measurements of total pipe line including all specials. No seprate payment will be made for accessories, specials. Payment for painting will be made seperately) (ii) 25 mm dia. medium quality |
| 18 | Supplying, fitting and fixing clear visioned, Insulated Double Glazed two track sliding Aluminium window (U-value < 3.2W/m 2 K) made up with 6 mm thick toughened glass (wt > 15kg/m 2 ) with 12 mm air gap in between, containing perforated Al/ structural foam spacer filled with moisture absorbant dessicant at all sides duly sealed with primary sealant (polyisobutylene) and affixed inside multi cellular/ multi chember profiles of required section made of Alluminium alloy extrusions conforming to IS:733-1983 and IS:1285 - 2002 annodised/powder coated with (required film thickness and specified colour /natural) matt finished conforming to IS: 1868- 2006/ IS: 13871-2002 measured as per IS:6012-1992, and sealed appropriately with secondary (polysulphide/silicon) sealant all junctions complete in all respect as per direction and satisfaction of Engineer-in-Charge including all incidental charges. (Payment shall be made on finished size of Aluminium window including frame |
| 19 | Labour charge for fabrication and installation of composite door, window, partitions made from annodized extruded alloy aluminium sections for the following units(C) Fully glazed single leaf reamless swing door made of anodized aluminium alloy extrusions fabrication after cutting to proper shape and size, drilling and aligning fitted with heavy duty hydraulic action floor spring with top pin assembly and fitted with inbuilt locking arrangement and all other necessary fittings, fixture, adhesives and joineries, cutting the glass to requisite shape and size mounting the edges for fitting the same with dry set neoprine/EPDM gasket |
| 20 | Supplying heavy duty hydraulic double action floor spring along with top pin/set of pivots conforming to IS: 6315 or any approved make as per direction of Engineer in charge |
| 21 | Supplying EPDM gusket of approved make and brand as per direction of Engineer in charge. iii) weather gasket / wool pile for door vertical |
| 22 | Supplying bubble free float glass of approved make and brand conforming to IS: 2835-1987.v) 6mm thick clear glass |
| 23 | Supplying 4 lever mortice lock or any approved make and brand as per direction of the Engineer- in Charge i) 150 mm |
| 24 | Filling the gap in between aluminium frame & adjacent RCC / Brick/ Stone work by providing weather silicon sealant over 6mm dia backer rod of approved quality as per architectural drawings and direction of Engineer-in-Charge complete. Upto 5 mm depth and 5 mm width(a) Ground Floor |
| 25 | Supplying, fitting and fixing E.W.C. in white glazed vitreous chinaware of approved make complete in position with necessary bolts, nuts etc. (a) With \"P\" trap |
| 26 | Supplying, fitting and fixing Flat back urinal (half stall urinal) in white vitreous chinaware of approved make in position with brass screws on 75 mm X 75 mm X 75 mm wooden blocks complete (i) 635 mm X 395 mm X 420 mm |
| 27 | Supplying, fitting and fixing shower of approved brand and make (i) (2) Chromium plated overhead Rain shower (Round), size-200mm dia. with revolving joint (Model Code No. F7010601 of CERA or equivalent) |
| 28 | Supplying, fitting and fixing towel rail with two brackets(b) Aluminium(ii) 25 mm dia. and 600 mm long |
| 29 | Supplying, fitting and fixing white vitreous china best quality approved make wash basin with C.I. brackets on 75 mm X 75 mm wooden blocks, C.P. waste fittings of 32 mm dia., one approved quality brass C.P. pillar cock of 15 mm dia., C.P. chain with rubber plug of 30 mm dia., approved quality P.V.C. waste pipe with C.P. nut 32 mm dia., 900 mm long approved quality P.V.C. connection pipe with heavy brass C.P. nut including mending good all damages and painting the brackets with two coats of approved paint(i) 450 mm X 300 mm size |
| 30 | Supplying, fitting and fixing pedestal of approved make for wash basin (white) |
| 31 | Supplying, fitting and fixing bevelled edged mirror 5.5 mm thick silver red as per I.S. 3438 / 1965 together with brass C.P. hinges. (ii) 600 mm X 450 mm |
| 32 | Supplying, fitting and fixing liquid soap container (c) Fibre glass |
| 33 | Supplying, fitting and fixing 10 litre P.V.C. low-down cistern conforming to I.S. specification with P.V.C. fittings complete, C.I. brackets including two coats of painting to bracket etc |
| 34 | Supplying and laying chequered tiles of any shade & of approved quality with (1:1½:3) cement concrete laid in panels or patterns as directed in pavement, footpath etc. including necessary underlay 25 mm thick [avg] cement mortar (1:3) complete in all respect with all labour and materials. [Using cement slurry @ 4.4 kg/Sq.m at back side and @2.4 kg/Sq.m for joint filling Red Variety(i) 25 mm. thick |
| 35 | Clearing compound premises of shurbs, plants, jungles etc.by cutting and removing as directed (Specific permission of Engineer-in-Charge prior to execution will be necessary).(Payment to be made on area cleared |
| 36 | Earth work in excavation of foundation trenches or drains, in all sorts of soil (including mixed soil but excluding laterite or sandstone) including removing, spreading or stacking the spoils within a lead of 75 m. as directed. The item includes necessary trimming the sides of trenches, levelling, dressing and ramming the bottom, bailing out water as required complete- Depth of excavation not exceeding 1,500 mm |
| 37 | Cement concrete with graded jhama khoa (30 mm size) excluding shuttering in ground floor and foundation- 1:3:6 proportion |
