|
| 1 | (66.1) Providing of IP20 SMD Mid Power LED batten type integrated light fixture made from Powder coated Extruded aluminium housing with in built driver , System lumen efficacy ≥ 110 lm/Watt output, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10% , P. F.≥0.95, CRI >80 , life time of minimum 50000 Burning Hours with , 70% of intial Lumen maintaned till life ends , CCT 3000°K / 4000°K / 5700°K /6000°K/6500°K (As per ANSI Bin) , Maximum power consumption should not more than the specified rating and Fixture shall be of BIS standard and trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79 & LM80) certificate / Report from OEM shall be submitted. All as per pre approved by Engineer incharge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR . |
| 2 | (66.1.1) 1170mm(+/-10%) LED batten with min. lumen output 2200 lm |
| 3 | (64.7) Providing of BEE Star rated copper wounded double ball bearing capacitor start, aluminium body & Metallic blade ceiling fan Conforming to all the performance requirements laid down in IS 374:2019 including all amendments, as applicable ; & Carry BIS licensing (i.e. ISI marking) with down rod up to 80 cm with secondary support safety cable ( steel rope) , cotter pin with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required. All as per pre approved by Engineer in-charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR . |
| 4 | (64.7.3) 1200 mm Sweep BEE 3 Star rated (service value >=5.0 to< 5.5 ) |
| 5 | (64.6) Providing of 400 mm Sweep BLDC technology Oscillating type Wall mounting / Pedestal type fans with Three speed, ON and OFF position, Double Wall bearing with front and back 120 or more ribs guard; Three no. blades, noise level should be <= 75 dB, including fixing with anchor bolts, making connection testing etc. as required. ( With Remote ) All as per pre approved by Engineer in-charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR . |
| 6 | (64.6.1) Wall mounting type with Service value 2.0 CMM /W, Min. Air Delivery 71 CMM |
| 7 | (66.4) Providing of IP20, 2\"x2\" LED Surface/ Recessed mounting Mid power SMD type LED Light fixture not less than 50mm housing depth made from CRCA sheet steel housing, high purity / transmisivity UV stabilized Non -yellowish diffuser for uniform light distribution. High efficiency with 4 KV internal/external surge protection BIS certified isolated driver having efficiency > 85% , with Short & Open circuit protection (Integral with light fixture). System lumen efficacy of ≥ 120 lm/Watt ,THD < 10 % , p.f.≥0.95,CRI >80 , life time of minimum 50000 Burning Hours with , 70% of intial Lumen maintaned till life ends , CCT 3000°K / 4000°K / 5700°K /6000°K/6500°K (As per ANSI Bin) , maximum power consumption should not more than the specified rating and Fixture shall be of BIS standard and trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. |
| 8 | (66.4.1.2) Recessed Type Minimum lumen output 3600 lm |
| 9 | (66.4.2.2) Surface Type Minimum lumen output 3600 lm |
| 10 | (53.1) Supplying of FR PVC insulated & nsheathed flexible copper conductor as per PWD specification for electrical Works with ISI marked (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from 99.90 % purity copper, class 5 stranding in acc. to IS:8130/IEC 60228 for lower watt loss , oxygen free for less chances of oxidization, insulation PVC type A/C/D , flame retardant as per IS 10810-53, better amperage rating as per IS:3961 part 5, in xisting surface or recessed PVC/ MS conduit/casing capping making connections with Copper Lugs of suitable size, Ferrules,testing etc. as required. OEM Must have its own in house NABL lab setup for all testing facilities for wires. |
| 11 | (53.1.1) 1 x 1.5 sq.mm |
| 12 | (53.1.5) 1 x 2.5 sq.mm |
| 13 | (53.1.10) 1 x 4 sq.mm |
| 14 | (53.1.15) 1 x 6 sq.mm |
| 15 | (53.1.21) 1 x 10 sq.mm |
| 16 | (53.1.2) 2 x 1.5 sq.mm |
| 17 | (53.1.6) 2 x 2.5 sq.mm |
| 18 | (53.1.11) 2 x 4 sq.mm |
| 19 | (53.1.16) 2 x 6 sq.mm |
| 20 | (53.1.18) 4 x 6.0 sq.mm |
| 21 | (53.1.23) 4 x 10.0 sq.mm |
| 22 | (53.7) Providing ISI marked P.V.C. insulated submersible cable confirming to(IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from 99.90 % purity copper, stranding in acc. to IS:8130/IEC 60228 for lower watt loss , oxygen free for less chances of oxidization, insulation PVC type A/C/D , flame retardant as per IS 10810-53, better amperage rating as per IS:3961 part 5, existing pipe / open trench / Cable tray / on surface including making connection etc. as required. |
| 23 | (53.7.1) 1.5 Sq.mm 3 core flat / Round |
| 24 | (53.7.2) 2.5 Sq.mm 3 core flat / Round |
| 25 | (53.7.3) 4 Sq.mm 3 core flat / Round |
| 26 | (53.7.4) 6 Sq.mm 3 core flat / Round |
| 27 | (53.7.5) 10 Sq.mm 3 core flat / Round |
| 28 | (55.1) Providing of 240/415 V AC MCB with positive isolation of 10 kA breaking capacity (B/ C/D tripping characteristic as per type of load and site requirement) 4 KV impulse withstand voltage, ISI marked IS 8828(1996) / conforming to IEC 60898-1 2002, IEC 60947-2, low watt losses, trip free mechanisum , energy limiting of class 3 as per IEC, minimum phase termination capacity of 35sq.mm. , conductor line load reversibility , IP 20 contact protection and fitted in existing distribution board/sheets, minimum electrical operation 20,000 upto 20 A rating and 10,000 upto 63 A, 5000 for 80 A & above rating including making connections, testing etc. as required. OEM shall have submit NABL / CPRI / ERDA accrediated lab type test reports & All as per pre approved by Engineer in charge. |
| 29 | (55.1.1.2) 6 A to 32 A rating Single pole |
| 30 | (55.1.2.2) 6 A to 32 A rating Double Pole |
| 31 | (55.1.2.3) 40 A rating Double Pole |
| 32 | (55.1.4.6) 100 A rating Four pole |
| 33 | (55.2) Providing of 240/415 V isolator ISI marked IS:13947-III/conforming to IEC 60947-3, suitable for AC22A utilization category, 4KV impulse withstand voltage, true contact indication, Red colour dolly / lever shall have single mould covering overallpoles for operation , two position din rail mounting, minimum phase termination capacity of 35sq.mm. IP 20 contact protection and fitted in existing distribution board / sheet including making connections, testing etc. as required. OEM shall have submit NABL / CPRI /ERDA accrediated lab type test reports & All as per pre approved by Engineer in-charge. |
| 34 | (55.2.1.2) 63 A Double pole isolator |
| 35 | (55.2.3.3) 100 A Four pole Isolato |
| 36 | (56.1) P & F ISI marked (IS:3854) 6 amp. flush type non modular switch with CM/L no. printed and made out from industrial grade Polycarbonate or fire resistant ABS material including cutting hole in tile and making connection testing etc. as required. All as per pre approved by Engineer in-charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR . |
| 37 | (56.2) P & F ISI marked (IS :3854) 16 amp. flush type non modular switch CM/L no. printed and made out from industrial grade Polycarbonate or fire resistant ABS material including cutting hole in tile and making connection testing etc. as required. All as per pre approved by Engineer in-charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR . |
| 38 | (56.3) Providing & Fixing of 6 amp. Combined flush type non modular socket and switch set as per PWD specification for electrical Works,made out from industrial grade Polycarbonate or fire resistant ABS material including cutting hole in tile and making connection testing etc. as required. All as per pre approved by Engineer in-charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR . |
| 39 | (56.4) Providing & Fixing of 16 amp. Combined flush type non modular socket and switch set with indicator and fuse set as per PWD specification for electrical Works, made out from industrial grade Polycarbonate or fire resistant ABS material including cutting hole in tile and making connection testing etc. as required. All as per pre approved by Engineer in-charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR . |
| 40 | (58.3) Supplyof 3 /4 pole current limiting Moulded case circuit breaker (MCCB) made of flame retardent & heat resistant material having following current rating, short circuit breaking capacity at 440/415 , 50 Hz; O/L & S/C settings , conforming to IS/IEC 60947 P -2 :2003 with front face and centralised adjustable, trip free mechanisum, true contact position indicator, line load interchangeability, designed for both horizontal & vertical mounting without any adverse effect on electrical performance, suitable for operation upto 55 degree and without derating upto 40 degree, pollution degree 3, having positive isolation capability, push (test) to trip, trip time less then 10 ms under s/c condition, Breaking capacity Ics = 100% ICU. U imp =8 KV, rated insulation voltage 690 V. provision for UVR , shunt trip , earth fault trip, door interlock, pad lock & rotary handle , including making connections etc. as required.OEM shall have submit NABL / CPRI / ERDA accrediated lab type test certificate before execution All as per pre approved by Engineer in-charge. |
| 41 | (58.3.4) 4 pole MCCB With Microprocessor based release with adjustable O/L & S/C setting with Inbuilt Instantaneous and Ground fault Protection |
| 42 | (58.3.3.2) up to 100 Amp , 25 kA, adjustable O/L & adjustable S/C setting,4 pole MCCB With Thermal Magnetic release |
| 43 | (58.3.4.1) Upto 160 Amp , 50 kA |
| 44 | (58.3.4.2) Upto 250 Amp , 50 kA |
| 45 | (58.3.4.3) Upto 400 Amp , 50 kA |
| 46 | (58.3.4.4) Upto 630 Amp , 50 kA |
| 47 | (58.3.4.5) Upto 800 Amp , 50 kA |
| 48 | (59.3) Providing of ISO certified company made TP&N 415 V Front handle operated double break fuse switch unit in sheet steel enclosure as per PWD specification for electrical Works conforming to IS/lEC 60947-3 : 1999 (W/O HBC fuses) including making connections with suitable lugs, testing etc. as required. Appropriate type test certificate / OEM test report shall be submitted . All as per pre approved by Engineer in-charge. |
| 49 | (59.3.2) 63 A rating |
| 50 | (59.3.3) 100 A rating |
| 51 | (59.3.5) 200 A rating |
| 52 | (59.3.8) 400 A rating |
| 53 | (59.5) Providing of ISO certified company made 240/415 V porcelain kitkat fuse (/HBC type) as per PWD specification for electrical Works conforming to IS:2086,1983 on existing board/sheet including making connections with lugs, testing etc. as required . Appropriate type test certificate / OEM test report shall besubmitted . |
| 54 | (59.5.5) 63 A , 415 V |
| 55 | (59.5.6) 100 A ,415 V |
| 56 | (59.5.7) 200 A , 415 V |
| 57 | (59.13) Providing of ISO certified company made bus bar chamber housed in sheet metal box as per PWD specification for electrical Works Confirming to IEC-60439/IS-8623 & IEC-60529/IS-2147 made out from 1.6 mm thick powder coated CRCA sheet,degree of protection IP-31, front openable bus bar made out of Copper suitable for 200 amp. Capacity , bus bar fixed on porcelain/DMC insulators at approved spacing including making connections etc. as required. Appropriate type test certificate / OEM test report shall be submitted . |
| 58 | (59.13.1) 300 mm long , 4 strip |
| 59 | (59.13.2) 450 mm long , 4 strip |
| 60 | (59.13.3) 600 mm long , 4 strip |
| 61 | (60.1) Providing of P.V.C. / XLPE insulated & P.V.C. sheathed UnArrmoured Aluminium cable confirming to IS:1554 P-I / IS :7098 P - I of 1.1 KV with H4- Grade electrolytic aluminium conductor confirming to IS 8130 of purity >99.6 %, Inner / outer sheath confirming to IS:5831 in existing RCC / Hume / Stoneware / PVC pipe/ open duct/cable trench / Cable tray (with cable tie) including testing etc. as required of following size. OEM must have it\"s own inhouse NABL accrediated Laboratory for testing procedure as per IS:10810 |
| 62 | (60.1.2.1) 6 sqmm x 2 Core |
| 63 | (60.1.3.1) 10 sqmm x 2 Core |
| 64 | (60.2) Providing of P.V.C. / XLPE insulated & P.V.C. sheathed Arrmoured Aluminium cable confirming to IS:1554 P-I / IS :7098 P - I of 1.1 KV with H4- Grade electrolytic aluminium conductor confirming to IS 8130 of purity >99.6 %, round / flat strip armouring of cables, Inner / outer sheath confirming to IS:5831 in existing RCC/ Hume / Stoneware / PVC pipe/ open duct/cable trench / Cable tray(with cable tie) including testing etc. as required of following size. OEM must have it\"s own in house NABL accrediated Laboratory for testing procedure. |
| 65 | (60.2.2.1) 6 sqmm x 2 Core |
| 66 | (60.2.3.1) 10 sqmm x 2 Core |
| 67 | (60.2.4.3) 16 sqmm x 4 Core |
| 68 | (60.2.5.3) 25 sqmm x 3.5 Core |
| 69 | (60.2.7.3) 50 sqmm x 3.5 Core |
| 70 | (60.2.8.3) 70 sqmm x 3.5 Core |
| 71 | (60.2.10.2) 120 sqmm x 3.5 Core |
| 72 | (60.2.12.2) 185 sqmm x 3.5 Core |
| 73 | (61.4) Supplying and making end termination with heavy duty Copper lugs ( ANY type ) confirming to IS 8337 -1976 duly crimped with crimping tool, PVC tape etc of following size.All as per pre approved by Engineer in-charge. |
| 74 | (61.4.5) 10sq.mm |
| 75 | (61.4.6) 16sq.mm |
| 76 | (61.4.7) 25sq.mm |
| 77 | (61.4.9) 50sq.mm |
| 78 | (61.4.10) 70sq.mm |
| 79 | (61.4.12) 120sq.mm |
| 80 | (66.1) Providing of IP20 SMD Mid Power LED batten type integrated light fixture made from Powder coated Extruded aluminium housing with in built driver , System lumen efficacy ≥110 lm/Watt output, internal surge protection of 2.5 KV with Short &Open circuit protection ,THD < 10% , P. F.≥0.95, CRI >80 , life timeof minimum 50000 Burning Hours with , 70% of intial Lumen maintaned till life ends , CCT 3000°K / 4000°K / 5700°K/6000°K/6500°K (As per ANSI Bin) , Maximum power consumptionshould not more than the specified rating and Fixture shall be of BISstandard and trade mark certificate ( T.C.). Manufactures WordMark/ Name Engraved/ Embossing/ Screen printing on housing. OEM must have its own in house NABL lab setup for all testingfacilities for LED fixtures. (LM79 & LM80) certificate / Report from OEM shall be submitted. |
| 81 | (66.1.1) 1170mm(+/-10%) LED batten with min. lumen output 2200 lm |
| 82 | (67.1) Providing of IK08 IP65 protected Top/Bottom mounted LED Post top Luminarie made of single piece construction powder coated die cast alluminium housing with UV stabalized Clear / frosted Polycarbonate diffuser and Aluminium anodised with sand blast reflector. The System level Luminous efficacy ≥ 100 Lumen/W. SMD LEDs is to be used, System CRI>70, CCT: 3000/4000/6500 K. The integral electronic driver must be potted & has a unique BIS R number must be potted & has a unique BIS R number constant current and Internal/external surge protection device of min. |
| 83 | (67.10.4) Minimum lumen output 4500 lm Post top Luminarie |
| 84 | (67.11) Providing of IK08 IP-66 protected high power LED floodlight system with single piece Pressure diecast aluminium housing, toughened glass diffuser with suitable lenses on LED to achieve various beam angles, of high power LED of 3 to 5 watt each . Integrated potted driver as a unique BIS R number having efficiency more than 85 % and in compliance to BIS certified and Trade mark certificate. The System level Luminaire efficacy >=125 lm/ wt. LED driver Input Voltage AC 120 to 270 V AC with High voltage Cutoff @>=300 V AC and Auto resetting Safety .Power Factor >0.95 , THD(I) <10% , driver current <=750mA. driver should be Phase to phase protection of 440 V for 4 Hrs. Electrical Connector , Surge Protection Min >=4KV internal and 10KV external but inside driver compartment, System life of 50000 Burning hours with 70% of Initial Lumens maintained, CRI>70 and CCT 5700K ±355K. Manufactures Word Mark/Name Engraved/Embossing/Screen printing on die cast housing to allow traceability/authenticity. Fixture shall be IS 10322 Complianced.OEM Must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79/LM80) Certificate/ report with liable warranty of product/accessories from OEM shall be submitted. All as per pre approved by Engineer in-charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR . |
| 85 | (67.11.5) High Power LED Flood Light Minimum lumen output 12400 lm |
| 86 | (67.13) Providing of IK10 IP65 protected 600 mm height LEDBollard Luminarie with base plate made of powder coated die castalluminium housing with UV stabalized PC diffuser. The Systemlevel Luminous efficacy ≥ 90 Lumen/W. SMD LEDs is to be used,System CRI>70, CCT: 3000/4000/6500 K. The integral electronicdriver must be potted & has a unique BIS R number must be potted& has a unique BIS R number constant current and Internal/externalsurge protection device of min. 4KV(L-N) and efficiency > 85%, PF>0.9, THD<20% and input Voltage range of 90-270V AC at 50Hz.System life of 30000 Burning hours with 70% of Initial Lumens maintained Light output in Cool white or Warm White Colour as perengineers choice. driver current <750mA. Fixture must be in compliance with BIS Standards and Trade mark Certificate complete in all respect.OEM Must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79/LM80) Certificate/report with liable warranty of product/accessories from OEM shall besubmitted. All as per pre approved by Engineer in-charge. For additional technical parameters of products/ work , refer Annexure\"A\" attached with this BSR . |
| 87 | (67.13.2) Minimum lumen output 980 lm Bollard |
| 88 | (67.14) Providing of IK10 IP66 / IP67 protected Rectangular shapeLED Step Luminarie made of powder coated die cast alluminiumhousing with UV stabalized PC diffuser. The System level Luminousefficacy ≥ 90 Lumen/W. SMD LEDs is to be used, System CRI>70,CCT: 3000/4000/6500 K. The integral electronic driver must be potted & has a unique BIS R number constant current and Internal/external surge protection device of min. 4KV(L-N) and efficiency > 85%, PF>0.9, THD<10% and input Voltage range of 140-270V AC at 50Hz. System life of 50000 Burning hours with 70% of Initial Lumens maintained . driver current <750mA . Fixture must be in compliance with BIS Standards and Trade mak Certificate complete in all respect.OEM Must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79/LM80) Certificate/ report with liable warranty of product/accessories from OEM shall be submitted. All as per pre approved by Engineer incharge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR . |
| 89 | (67.14.3) Minimum lumen output 800 lm Step light |
| 90 | (50.4) Supply of following sizes (dia.) of ISI marked virgin material MMS ( IS:9537 P - III ) PVC conduit along with ISI marked (IS:3419-1988)accessories as required in recess including cutting the wall, covering conduit and making good the same as required. For additional technical parameters of product / work refer Annexure \"A\" attached with this BSR |
| 91 | (50.4.3) 32 mm |
| 92 | (56.5) Providing of ISI marked (IS :3854) non modular 6A bell push surface type CM/L no. printed and made out from industrial grade Polycarbonate or fire resistant ABS material including making connection testing etc. as required.All as per pre approved by Engineer in-charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR . |
| 93 | (56.9) Providing of ISI marked non modular 6A hanging bell push/one way switch made out from industrial grade Polycarbonate or fire resistant ABS materialincluding making connection testing etc. as required.All as per pre approved by Engineer in-charge |
| 94 | (56.1) Providing of of 3/5 pin 6 amp. flush type non modular socket made out from industrial grade Polycarbonate or fire resistant ABS material, brass terminal with Porcelain based back cover & captive screws including cutting hole in tile and making connection testing etc. as required.All as per pre approved by Engineer in-charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR . |
| 95 | (56.11) Providing of 3/6 pin 16 amp flush type non modular socket made out from Industrial grade Polycarbonate or fire resistant ABS material, brass terminal with Porcelain based back cover & captive screws including cutting hole in tile and making connection testing etc. as required.All as per pre approved by Engineer in-charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR . |
| 96 | (56.14) Providing of ISI marked (IS:1293) 6 amp unbreakable 3 pin plug top having lamp indicator with CM/L no. printed and made out from industrial grade Polycarbonate or fire resistant ABS material, brass terminal including making connection testing etc. as required. All as per pre approved by Engineer in-charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR . |
| 97 | (56.15) Providing of ISI marked (IS:1293) 16 amp unbreakable 3 pin plug top having lamp indicator with CM/L no. printed and made out from industrial grade Polycarbonate or fire resistant ABS material, brass terminal including making connection testing etc. as required. All as per pre approved by Engineer in-charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR . |
| 98 | (56.23) Providing of ISI marked (IS:2268-1994) gong bell with CM/L no. printed including making connection testing etc. as required. All as per pre approved by Engineer in-charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR . |
| 99 | (56.24) Providing of ISI marked surface type buzzer (IS:2268-1994) with CM/L no. printed including making connection testing etc. as required. All as per pre approved by Engineer in-charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR . |
| 100 | (56.25) Providing of single / multi tone electronic call bell as per PWD specification for electrical Works, including making connectiontesting etc. as required. All as per pre approved by Engineer incharge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR . |
| 101 | (56.26) Providing of ding dong/musical chime bell as per PWD specification for electrical Works, including making connection testing etc. as required.All as per pre approved by Engineer incharge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR . |
| 102 | (64.11) Providing of Double ball bearing, copper wounded capacitor start single phase metallic blade fresh air fan, in existing opening including cost of hardware , flexible 3 core copper conductor ,making connections, testing etc. as required. All as per pre approved by Engineer in-charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR . |
| 103 | (64.11.2) 300 mm sweep |
| 104 | (64.12) Providing of Heavy duty capacitor start, copper wound Double ball bearing 900/1400 RPM single phase Exhaust fan conforming to IS:2312 ISI marked in existing opening including making connections testing etc. as required. All as per pre approved by Engineer in-charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR . |
| 105 | (64.12.3) 450 mm sweep(900/1400 RPM) |
| 106 | (66.3) Providing of IP-20 LED Recessed / Surface Mounted, Round / Sqaure SMD Mid Power LED Downlight with power coated die-cast aluminum housing with UV Stabilized non yellowish Diffuser with BIS complience 2.5 KV surge protected Isolated driver, with Short & Open circuit protection, having efficiency > 85% . System Lumen efficacy of ≥ 110 lm / watt, THD < 10 % , Pf.≥0.95, CRI >80, life time of minimum 50000 Burning Hours with , 70% of intial Lumen maintaned till life ends , CCT 3000°K / 4000°K/ 5700°K /6000°K/6500°K (As per ANSI Bin) , maximum power consumption should not more than the specified rating and Fixture shall be of BIS standard and trade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. |
| 107 | (66.3.2.3) Surface Mounting (with extruded alumn. Housing ) Minimum lumen output 1950 lm |
| 108 | (66.3.2.4) Surface Mounting (with extruded alumn. Housing ) Minimum lumen output 2400 lm |
| 109 | (57.2) Supplying of Aluminium (IEC 60105 ISO 209-1,2) / Copper (IEC 60028) bus bar by means of SMC / DMC type insulator with standard short circuit withstand capacity , high tensile nuts and bolts spring washers in existing panel including bending , cutting in required shape and size and colour coding with heat shrinkable PVC sleeves. All as per pre approved by Engineer in-charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR . |
| 110 | (57.2.1) Electrolytic grade Aluminium bus bar 6010 grade |
| 111 | (64.1) Providing of 1.2mm thick M.S. Recessed fan box, hexagonal/ round of size 130 mm dia, depth 75mm, 12 mm dia rod fan hook with 100 mm length extended on each side . All as per pre approved by Engineer in-charge. For additional technical parameters of product / work refer Annexure \"A\" attached with this BSR |
| 112 | (56.31) Providing of following size mounting grid plates with cover plates made from fire retardent UV established high-performance engineering plastic suitable for all universal metal boxes for front installation & removal direct fit type complete in all respect.All as per pre approved by Engineer in-charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR . |
| 113 | (56.31.1) 1/2 Module |
| 114 | (56.31.2) 3 Module |
| 115 | (56.31.3) 4 Module |
| 116 | (56.31.4) 5 Module |
| 117 | (56.31.5) 6 Module |
| 118 | (56.31.6) 8 Module |
| 119 | (56.31.7) 10 Module |
| 120 | (56.31.8) 12 Module |
| 121 | (56.31.9) 16/18 Module |
| 122 | (56.32) Providing of Wiring Accessories OEM fabricated following size GI box of 1.2 mm thick with earthing terminal and adjustable floating clamp in recess/ surface suitable for modular accessories as required.All as per pre approved by Engineer in-charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR . |
| 123 | (56.32.1) 1-2 Module |
| 124 | (56.32.2) 3 Module |
| 125 | (56.32.3) 4/5 Module |
| 126 | (56.32.4) 6 / 8 module |
| 127 | (56.32.5) 10 / 12 module |
| 128 | (56.32.6) 16/18 module |
| 129 | (56.33) Providing of Wiring Accessories OEM fabricated following size virgin material UPVC modular boxes on surface suitable for modular accessories as required.All as per pre approved by Engineer in-charge. For additional technical parameters of products/ work , refer Annexure \"A\" attached with this BSR . |
| 130 | (56.33.1) 1-2-3 Module |
| 131 | (56.33.2) 4-5 Module |
| 132 | (56.33.3) 6-8 Module |
| 133 | (56.33.4) 10-12 Module |
| 134 | (56.33.5) 16/18 Module |
| 135 | Supply of Extension Board having 4 switch soket of 6 AMP and 1. 5 mtr Heavy duty wire made on wooden box |
| 136 | Supply of Extension Board having 2 switch soket of 16 AMP and 1. 5 mtr Heavy duty wire made on wooden box |
| 137 | Supply of LED Bulb |
| 138 | Power consmption 9-10 watt Light colour white 1400-1500 Make:- Philips, Hawells, Halonix |
| 139 | Power consmption 15-18 watt Light colour white 1400-1500 Make:- Philips, Hawells, Halonix |
| 140 | Supply of Fall celing down light 9 watt |
| 141 | Providing of 5W Spot LED light |
| 142 | Providing of 9W COB Spot LED light |
| 143 | Providing of 1X1 LED Penal of 20-25 Watt |
| 144 | Providing of Decorative Picture LED light |
| 145 | White Colour LED |
| 146 | 12 inch |
| 147 | 18 inch |
| 148 | Warm White Colour LED |
| 149 | 12 inch |
| 150 | 18 inch |
| 151 | Supply of PVC Tape Roll |
| 152 | Providing of Tube light Rod 36 W |
| 153 | Providing of Tube light starter |
| 154 | Providing of Tube light Choke |
| 155 | Providing of Heat convertor make Usha/bajaj |
| 156 | Providing of Room Heater 2000W |
| 157 | Providing of Room Heater of OIL TYPE 13 FIN |
| 158 | Providing of LT MIP meter box for new JVVNL meter connection. |
| 159 | Providing of CT, PT for LT Line of size 100/5 for new JVVNL meter connection. . |
| 160 | Providing & Fixing of PVC gang box of size 6x2 |
| 161 | Providing & Fixing of PVC gang box of size 6x3 |
| 162 | Providing & Fixing of PVC gang box of size 6x4 |
| 163 | Providing & Fixing of PVC gang box of size 8x3 |
| 164 | Providing & Fixing of PVC gang box of size 8x4 |
| 165 | Providing & Fixing of PVC gang box of size 8x5 |
| 166 | Providing & Fixing of PVC gang box of size 12x4 |
| 167 | Providing & Fixing of PVC gang box of size 12x5 |
| 168 | Providing & Fixing of PVC gang box of size 12x6 |
| 169 | Providing & Fixing of PVC gang box of size 12x8 |
| 170 | Providing & Fixing of Modular Suface box 6 Module |
| 171 | Providing & Fixing of Modular Suface box 8 Module |
| 172 | Note :- For supply electric material, Item rate should be decreased by 10% of BSR Rate 2023 Please Enable Macros to View BoQ information |
