|
| 1 | B & R Division Items |
| 2 | Demolition of un-reinforced cement concrete in ground floor and paving not exceeding 15 cm thick (below or above ground level) complete all as specified and directed. |
| 3 | Demolition of cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed. |
| 4 | Demolition of brick work or stone/ boulder masonry, built in cement mortar including all quoins, pillars etc. complete all as specified and as directed. |
| 5 | Demolition of reed lathing, single or double including battens and plaster or chiken wire lathing all as specified. |
| 6 | Dismantling floor, hearth or wall tilling including cement mortar bedding (but not backing) removing serviceable tiles to stores and rubbish off the premises. |
| 7 | Dismantling mild steel work or wrought iron of any description and in any position complete all as specified and as directed. |
| 8 | Dismantling plain or corrugated steel sheeting, any gauge or any thickness as in roof covering, wall cladding, etc.including all necessary staging / scaffolding, etc. as required complete all as specified and as directed. |
| 9 | Dismantling of timber scantling 40 Sqcm and over in section, in any position in unframed work complete all as specified and directed. |
| 10 | Dismantling of timber fillets rails, posts, rafters, pulins etc under 40 sqcm in setion in any position in unframed work complete all as specified and directed. |
| 11 | Dismantling wall and ceilingboards (fibre, pulb, insulation etc) or insulation boards slabs/blankets any thickness including cover fillets all as specified and as directed. |
| 12 | Dismantling boarding any description fixed in any position with nails all as specified. |
| 13 | Dismantling PVC pipe 50/75/110 mm dia as in wall, floor, sewage line including clamps complete all as specified and directed. |
| 14 | Taking down cement plaster on brick or stone walls etc, including raking out joints, hacking for key scrubing down with water etc complete all as specified and as directed. |
| 15 | Taking down wooden shutters of size exceeding 1.0sqm but not exceeding 2.0 sqm and refixing in same opening after minor repairs easing out etc complete all as specified and directed. |
| 16 | Taking down chowkhats or frame with shutters (without taking off shutters from frame) each not exceeding 1.50 Sqm each complete all as specified. |
| 17 | Taking down Chowkats or frames with shutters exceeding 1.5 Sqm but not exceeding 4 Sqm each (without taking off shutters from the frame) complete all as specified. |
| 18 | Taking up or down 15mm diaGI steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed. |
| 19 | Taking up or down 20mm diaGI steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed. |
| 20 | M&Lfor providing 75 mm thick cement concrete (1:4:8) type D-2 using (40mm gradedstone aggregate) as in Sub base of floor rough surface for receiving tile complete all as specified. |
| 21 | M&Lfor providing 75 mm thick plain cement concrete (1:3:6) type C-2 using (40mm gradedstone aggregate) as in plinth protection finished even and fair without using extra cement laid inpanels and joints filled with bituminous mastic filling with 1 part of bitumen and 3 part of sand complete all as specified and directed. |
| 22 | M&L for PCC type C- 1:3:6 (Using 40mm graded aggregate) as in surface channel and drain, foundation of manhole complete all as specified & directed. |
| 23 | Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends foretccomplete all as specified and directed. |
| 24 | Add or deduct for each 25 mm girth or part thereof over or under 30cm(For adjustment in girth of item mention above) |
| 25 | M&L for 40mm thick plain cement concrete 1:2:4 type B-0,(Using 12.50 mm graded agg.) as in levelling course on roof top or similar work finished fair and even complete all as specified and directed. |
| 26 | M&L for plain cement concrete 1:2:4 type B-0,(Using 12.50 mm graded agg.) as in hunching, roof karb, levelling course on roof top or similar work finished fair and even complete all as specified and directed. |
| 27 | Supply & laying3 mm thick(minimum) APP based polymeric membraneweighing not less than 3.0 kg/Sqm reinforced with polyester non woven fabric (weighing not less than160 gms/sqm) with minimum 100 mm transverse laps and 75 mm longitudinal lap over RCCand application shall be according to manufactures\"s instructions over cold solvent Bituminious primer @ 0.25 ltr/Sqm. Application of polymeric membrane shall be bytorching etc as per manufacturer\"s instruction and complete all as directed |
| 28 | M & L applying two coat of aluminium paint @ 0.11kg/ sqm over the APP modified membrane complete all as specified. |
| 29 | M & LProviding and laying 60mm thickness factory made precast concrete interlocking paver block of M-35 grade any size and shape confirming to IS 15658-2006 with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand; complete all as specified & as directed.Note : Item of Sand filling will be paid seperatly in relevant item. |
| 30 | M & L for brickwork with subclass \"B\" or locally available best qualityold size bricks, straight or curved on plan exc 6 m mean raduis,built in CM (1:6) complete all as specified and directed. |
| 31 | M & L for half brick work in cement mortar (1:4) straight or curved on plan to any radius with locally available Subclass ‘B’ old size best quality bricks all as specified . |
| 32 | M & Lrendering 5mm thick cement plaster on fair faces ofof brick or concrete surfaces of soffits of slabs, ceiling in CM (1:3) finished fair and even complete all as specified. |
| 33 | M & Lrendering 10mm thick cement plaster on other than fair faces of brick wall or concrete surfaces in CM (1:6) finished fair and even complete all as specified. |
| 34 | M & Lrendering 10mm thick cement plaster on other one side lathing, other than fair faces of brick wall or concrete surfaces in CM (1:6) finished fair and even complete all as specified. |
| 35 | Material and labour for 10 mm thick screed bed in cement mortar 1:4 over roof and connected surfaces finished fair and even without using of extra cement with mixed WPC @ 3% complete all as specified.Note:- WPC shall be measured and paid separately. |
| 36 | Material and labour for 15 mm thick rendering in cement mortar 1:4 on fair faces of brick wall or concrete surfaces, finished the surfaces even and fair with using of WPC @ 3% complete all as specified. Note:- WPC shall be measured and paid separately. |
| 37 | M & Lrendering 15 mm thick cement plaster in two layer each of 10+5 mm thick on one side of lathing, other than fair faces of brick wall or concrete surfaces in CM (1:4) & water proofing compound mixed with second layer @ 3% finished even and smooth without using extra cement complete all as specified. (Note :WPC measured separately). |
| 38 | Supply only integral waterproofing compound etc complete all as spd and directed. |
| 39 | S&F for GI wire netting 0.71 mm dia and 12 mm mesh lathing to wood or metal studding joints etc in walls ceiling stanchion,beams etc included all laps cutting and wastes complete all as specified and directed. |
| 40 | M & L Non Skid ceramic coloured tiles 7 to 8mm thick (square/ rectangular) area of each tile exceeding 0.11 but not exceeding 0.18 sqm, as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile including 15 mm thick screed bed or bedding layers in cement mortar 1:4 over brushing with neat cement slurry as specified |
| 41 | M & LGlazed ceramic coloured tilesin vertical surface size 450mm x 300mm x & ( 6mm to 7mm )mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over & including10mm thick screed bed or backing coat in cement mortar 1:4layingof skirting/dado on walls all as specified and directed. |
| 42 | M&L Machine cut kota stone slab flooring 20-25mm thick as in floor, over cement screed base laid over 20mm thick screed bed in cm 1 : 6 with cement slurry @ 4 kg/sqm jointed and pointed with grey cement slurry mixed with pigment to match the shade of slab including cutting and polishing to achieve mirror/granite finish complete all as specified and as directed. |
| 43 | M&L Machine cut kota stone slab flooring 20-25mm thick as in tread, riser, skirting over cement screed base laid over 20mm thick screed bed in cm 1 : 6 with cement slurry @ 4 kg/sqm jointed and pointed with grey cement slurry mixed with pigment to match the shade of slab including cutting and polishing to achieve mirror/granite finish complete all as specified and as directed. |
| 44 | Supply and fix pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with self tapping screws as specified. |
| 45 | Supply and fix pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified. |
| 46 | Supply and fix0.63 mm thick Galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with fixed with L-type or J-type or cranked hook bolts in lieu of screws , nut and washers, in roofs, walls etc. with grade of zinccoating 275 complete all as specified and directed. |
| 47 | fixing only Galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with fixed with L-type or J-type or cranked hook bolts in lieu of screws , nut and washers, in roofs, walls etc. with grade of zinccoating 275 complete all as specified and directed.Note : Old sheet obtained from the respective dismantling items which are in good condition will be reused. |
| 48 | Supply and fix 0.63 mm thick Plain, galvanised, mild steel sheeting, in ridges ,hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 complete all as specified and directed. |
| 49 | fixing only Plain, galvanised, mild steel sheeting, in ridges ,hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 complete complete all as specified and directed.Note : Old sheet obtained from the respective dismantling items which are in good condition will be reused. |
| 50 | Supply and fix 4.0mm thick asbestos cement plain building boards fixed to timber frame work with screw complete all as specified and directed. |
| 51 | Supply and fix Framed work such as grills, gratings, etc.. with ends of bars or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed. |
| 52 | Supply and fix Steel work in trusses, purlins, posts and the like using tubular/ square hollow sections including special shaped washer etc. complete using ERW or induction butt welded tubes/SHS conforming to IS.1161 - 2014 / IS.4923 - 1997 grade St.-240 complete all as specified and directed. |
| 53 | Supply and fix Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment conforming to Fe 290 grade E-165 complete all as specified. |
| 54 | Supply and fix Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges large hasps and staples; chains; hand made slidingbolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers,hold fasts, bands, straps, wall ties, plain angle cleats, eaves board frame and similar articles conforming to Fe-290 Gde-E-165 completeall as specified and directed. |
| 55 | Supply and fix stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessarystainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement completeall as specified and directed. |
| 56 | S & F Pressed steel frames made of 1.25mm thick MS sheet of profile 125x60mm for door and window frames with one or more rebates includinghinges (100/50mm SS), lock strike plate, shock absorber, treating of internal surfaces of chowkhats with coal tar or black paint including hinges, hold fasts/lugs etc complete all as specified. |
| 57 | S & F Pressed steel frames made of 1.25mm thick MS sheet of profile 105x60mm for door and window frames with one or more rebates includinghinges (100/50mm SS), lock strike plate, shock absorber, treating of internal surfaces of chowkhats with coal tar or black paint including hinges, hold fasts/lugs etc complete all as specified. |
| 58 | M & LPlain Cement concrete (1:3:6), type C-0 using 12.5mm graded stone aggregate as in filling of steel chowkhatsand concrete for fixing of holdfast including necessary form work complete all as specified. |
| 59 | S&F Steel windows with side hung shutters including box type hinges with steel handles, 100mm long peg stay complete with glazing bars, dovetailed or welded, including locking arrangements complete all as specified directed. |
| 60 | S&F Steel windows with side hung shutters including box type hinges with steel handles, 100mm long peg stay complete without glazing bars, dovetailed or welded, including locking arrangements complete all as specified directed. |
| 61 | S&F Steel ventilator with top hung shutter including hinges, steel peg stay, lugs as in hold fast with locking arrangements, complete all as specified. |
| 62 | M & L for second class harwood timber scantlings in wroughtfixed to unframed work scantling 40 sqcm and over in section in any position complete all as specified and directed. |
| 63 | M & L for second class harwood timber scantlings in clean sawn fixed to unframed work scantling 40 sqcm and over in section in any position complete all as specified and directed. |
| 64 | M & L for 2nd class hardwood fillets square, rectangular or tringular in section clean sawn screwed with nails exc 6 sqcm and n.exc 13 sqcm complete all as specified. |
| 65 | M & L for second class harwood fillets square, rectangular or tringular in section clean sawn, fixed with screwed exc 13 sqcm and n. exc 25 sqcm complete all as specified and directed. |
| 66 | M & L for 2nd class hardwood fillets square, rectangular or tringular in section wrought screwed with nails exc 6 sqcm and n.exc 13 sqcm complete all as specified. |
| 67 | M & L for 2nd class hardwood fillets square, rectangular or tringular in section wrought, fixed with screwed exc 13 sqcm and n.exc 25 sqcm complete all as specified. |
| 68 | M & L for second class harwood plain fillets square, rectangular or tringular in section wrought, bull nosed, splayed, chamfered or rounded on one edge or face, sectional area exc 6sqcm but not exc 13 sqcm complete all as specified and directed. |
| 69 | M & L for 18mm / 19mm thick block boards, grade 2 quality, interior grade, decorative type with decorative face veneer on one face fixed with screw to timber frame work complete all as directed. |
| 70 | S&F 2nd class hard woodglazed andskeletonventilator/ window 30 mm thick open rebated and prepared to receive glass, wiremesh gauge etc (without sash bars), edge of framing plain chemfered rounded fitted with cut and mitred beds for securing glass etc size of members size of members of shutter as specified in SSR part I section 8 clause 8.20(b) complete all as specified and directed. |
| 71 | S & F 2nd class hard woodglazed andskeleton door shutters 35 mm thickdivided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers, edge of framing plain chemfered ro rounded fitted with cut and mitred beds for securing glass etc size of members of window ventilator etc are provided stile and rail as specified in SSR Part I section 8 clause 8.20(a) |
| 72 | S & F 30 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides, smooth finish with lipping of teak wood on edges all as specified and directed |
| 73 | S & F Solid PVC door frame of size 50 mm x 47 mm made of 5 mm plain colour PVC sheet reinforced with mild steel square tube complete all as specified in clause 8B.3.1 and shown on page 150 of MES Schedule Part-II (2010). |
| 74 | S & F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, supply and fixing in the frame at site as per clause 8 B.2.1 of MES schedule Part-II (2004) complete all as specified. Make: Rajshri or equivalent as approved. |
| 75 | S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) withextruded built up standard tubular sections/ appropriate Zsections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with requiredEPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle,Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge |
| 76 | Supply and fixStainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified. |
| 77 | Supply and fix as in repairStainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified. |
| 78 | S&F 3.00 mm thick sheet glass frosted ordinary quality and glazing with oil putting square nexc 0.5 sqm in each pane complete including hacking out old broken glass any thickness and size from any frame all as specified. |
| 79 | S&F 3.00 mm thick sheet glass ordinary quality and glazing with oil putting square nexc 0.5 sqm in each pane complete all as specified. |
| 80 | S&F 4.00 mm thick sheet glass ordinary quality and glazing with oil putting square exc 0.5 sqm in each pane complete all as specified. |
| 81 | S&F 100mm MS Butt hinges, medium weight, cold rolledcomplete all as specified. |
| 82 | S&F 100mm long aluminum alloy Butt hinges, extruded, anodised with GI hinge pin fixed complete all as specified. |
| 83 | Supply and fix 300mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixedcomplete all as specified. |
| 84 | Supply and fix 150 mm long aluminium handles cast type anodised complete all as specified & directed . |
| 85 | Supply and fix 200 mm long aluminum anodised barrel tower bolts of extruded section complete all as specified and directed. |
| 86 | Supply and fix door stopper of aluminum alloy body and tongue, anodised with hard drawn steel springs, fixed to door with over all length 150mm with rubber bush complete all as specified & directed . |
| 87 | Supply and fix as in repair vitreous china Squatting pan, \"Orissa\" pattern, Size 580 X 440mm ,with integral foot rests (excluding flushing ciestern and flush pipe) incl necessary lime concrete and 100 mm bore cast iron \"P\" trap with 550 to 600mm long neck for connecting WC to branch piece with cement joints complete all as specified & as directed . |
| 88 | Supply and fix, as in repair,vitreous china wash basin, white flat back size 550 x 400 mm, excluding taps, waste chain, plug and porcelain stopper but including cp coupling, brackets, cutting for and pinning in ends of bracket or erecting stand complete all as specified. |
| 89 | S & F as in repair PVC valveless,syphonic action type,low level flushing cistren 10 ltr capacity ISI Marked incl all acessories and 32mm dia PVC flush / discharge pipe incl float valve, inlet complete all as specified. |
| 90 | S & F as in repair PVC connections 15 mm size with PTMT nuts of length 450 m complete all as specified. |
| 91 | S & F as in repair 15mm bore pillar tap cast copper alloy with capstan head, fancy type, chromium plated, concealed screwed down high pressure with or without hot or cold with long shunk screwed shanks and fly nuts screwed for iron pipes and connecting to water pipe line complete all specified and directed. |
| 92 | Supply and fix as in repair 15 mm bore bib taps fancy type, chromium plated, castcopper alloy with crutch or butter fly handle, screwed down, screwed for iron pipe or for brass ferrule all as specified. |
| 93 | Supply and fix as in repair 15mm bore stop valve/angle valve, cast copper alloy cromium plated fancy type screwed down high pressure, with crutch or butterfly handle for 15 mm bore pipe or for unions all as specified. |
| 94 | Supply and fix as in repair stainless steel sink with drainage board, 1.00mm thick for kitchen or laboratory, with plug, waste pipe, washers, including cantilever cast iron brackets, connecting union etc.,overall size 915mm x 460 mm with bowl size 410mm x 330mm x 160mm including bedding in cement mortar on dwarf wall, fixing cantilever bracket, connecting union to pipe etc complete all as specified and as directed. |
| 95 | S & F 600mm X 450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed. |
| 96 | Supply and fix 110mm diaPVC (SWR) pipes single socketed, in any length, laid in trenches or in floors / fixed to walls complete all as specified. |
| 97 | Supply and fix 75mm diaPVC (SWR) pipes single socketed, in any length, laid in trenches or in floors / fixed to walls complete all as specified. |
| 98 | Supply and fix 110mm dia PVC (SWR) bend suitable for pipe complete all as specified. |
| 99 | Supply and fix 750mm dia PVC (SWR) bend suitable for pipe complete all as specified. |
| 100 | Supply & Fixed 110mm dia to 75mm dia PVC (SWR) reducer equal or unequal suitable for pipe complete all as specified. |
| 101 | Supply & Fixed 110mm dia PVC (SWR) vent cowl suitable for pipe complete all as specified. |
| 102 | Supply & Fixed 75mm dia PVC (SWR) vent cowl suitable for pipe complete all as specified. |
| 103 | M & L75mm dia PVC(SWR) floor trap, outlet, plain with grating including jointing with solvent cement complete all as specified. |
| 104 | Supply and fix 110mm bore PVC (SWR) junction, single T equal or unequal with or without door access complete all as specified. |
| 105 | S&F 15mm bore steel water tubing, medium grade, galvanised with screwed and socketed joints, in any length, including supply and fixing all fittings, ISI marked conforming to IS -1239 and fixed to walls or laid in floors / trenches required for water connections complete all as specified and as directed. |
| 106 | S&F 20mm bore steel water tubing, medium grade, galvanised with screwed and socketed joints, in any length, including supply and fixing all fittings, ISI marked conforming to IS -1239 and fixed to walls or laid in floors / trenches required for water connections complete all as specified and as directed. |
| 107 | Fixing only old 15mm bore steel water tubing, medium grade, galvanised with screwed and socketed joints, in any length, including supply and fixing all fittings and fixed to walls or laid in floors / trenches required for water connections complete all as specified and as directed.Note : Old GI Pipe obtained from the respective taking out/ down items which are in good condition will be reused. |
| 108 | Fixing only old 20mm bore steel water tubing, medium grade, galvanised with screwed and socketed joints, in any length, including supply and fixing all fittings and fixed to walls or laid in floors / trenches required for water connections complete all as specified and as directed.Note : Old GI Pipe obtained from the respective taking out/ down items which are in good condition will be reused. |
| 109 | S&F gun metal gate valve 20mm dia, cast copper alloy, screwed down high pressure with crutch or butterfly handle screwed both ends for suitable iron pipe complete all as specified and directed. |
| 110 | Supplying, hoisting, fixing and connecting up 500 litre rotational moulded polythylene water storage tanks double layer (cylindrical vertical with closed top), hoisted and fixed in position all as specified in SSR Part-I including connecting the overflow drain out, inlet and outlet pipes, tank nipple, elbow, bend, unions, sockets, etc. including taking down old damaged water tank and disposing off complete all as specified and as directed |
| 111 | Supplying, hoisting, fixing and connecting up 1000 litre rotational moulded polythylene water storage tanks double layer (cylindrical vertical with closed top), hoisted and fixed in position all as specified in SSR Part-I including connecting the overflow drain out, inlet and outlet pipes, tank nipple, elbow, bend, unions, sockets, etc. including taking down old damaged water tank and disposing off complete all as specified and as directed |
| 112 | Material and labour for pre-painted designer false ceiling using E-grid 2430, 180 GSM (exposed ceiling suspension system ) of grid size 600 mm x 600 mm with main runner 38 mm x 24 mm and wall angle 24 mm x 24 mm using 4 mm thick High Pressure Non Asbestos Fibre Cement prepainted decorative board (E-Board Classic)in a grid of GI system duly suspended with 4 mmdia GI bar hanger fixed with steel dash fasteners or iron purlin from the roof with adjustment clip providing positions for light fixtures, air conditioning diffuser and ducts ,sprinkler ,smoke detectors etc. The main runners to be secured to structural soffits by hanger @ 1220 mm maximum c/c. the last hanger at the end of each main runner should not be placed at more than 450 mm from the adjacent wall, Flush fitting 1220 mm cross tee to be interlocked between main runners @ 610 mm c/c,so as to form 600 mm x 600 mm grid and painted with two coats of acrylic emulsion paint of approved shed /make over a coat of cement primer before installing it on the grid complete all as specified . Make: Everest Industries Ltd or equivalent as per IS 14862. |
| 113 | M & Lfor preparation of old decorated plastered or unplastered wall surfaces including brooming down or steel wire brushing , scrapping down smoke, soot , moulds , moss and efflorescent salts and trading oil and greasy spots etcand applying one coats of white wash complete all as specified and directed. |
| 114 | M & Lfor preparation of old decorated plastered or unplastered ceiling surfaces including brooming down or steel wire brushing , scrapping down smoke, soot , moulds , moss and efflorescent salts and trading oil and greasy spots etcand applying one coats of white wash complete all as specified and directed. |
| 115 | M & Lfor preparation of new wall surfaces incl cornices and applying three coats of white wash complete all as specified and directed. |
| 116 | M & Lfor preparation of new ceiling surfaces and applying three coats of white wash complete all as specified and directed. |
| 117 | M & Lfor preparation of old decorated plastered or unplastered wall surfaces including brooming down or steel wire brushing , scrapping down smoke, soot , moulds , moss and efflorescent salts and trading oil and greasy spots etcand applying one coats of oil emulsion distemper with using roller complete all as specified and directed. |
| 118 | M & Lfor preparation of old decorated plastered or unplastered wall surfaces including brooming down or steel wire brushing , scrapping down smoke, soot , moulds , moss and efflorescent salts and trading oil and greasy spots etcand applying two coats of oil emulsion distemper over a coat of wall primer with using roller complete all as specified and directed. |
| 119 | M & L preparation of new plastered surface of walls and applying two coat of oil emulsion distemper over one coat of primer with using roller complete all as specified. |
| 120 | Material and labour for preparation of new wall plasterd surfacesand applying 1 mm thick wall putty to prepare the surface even smooth complete all as specified. |
| 121 | Material & Labour for preparation of new plastered surface applying two or more coats of 100% Premium acrylic emulsion paint@ 1.67 ltr/10 Sqm having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 2.20 litre/ 10 sqm complete all as specified. |
| 122 | Material & Labour for preparation of old plastered surface applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm using roller complete all as specified and directed. |
| 123 | M & Lpreparation of new steel surfaces of any description over 10cm width or girth not otherwise described and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and as directed. |
| 124 | Prepartation of old painted steel surfaces over 10 cm width or girth not otherwise described and applying one coat of synthetic enamel paint, complete all as specified and directed. |
| 125 | M & Lfor preparation of new wooden surfaces of any description not other wise described over 10 cm width or girth and applying two coat of Synthetic enamel paint over a coat of pink primer complete all as specified and as directed. |
| 126 | M & Lfor preparation of new wooden surfaces of any description not other wise described n. exc. 10 cm width or girth and applying two coat of Synthetic enamel paint over a coat of pink primer complete all as specified and as directed. |
| 127 | M & Lfor preparation of old wooden surfaces of any description not other wise described over 10 cm width or girth and applying one coat of Synthetic enamel paintcomplete all as specified and as directed. |
| 128 | M & Lfor preparation of old wooden surfaces of any description not other wise described over 10 cm width or girth and applying two coat of Synthetic enamel paintcomplete all as specified and as directed. |
| 129 | M & Lfor preparation of old wooden surfaces of any description not other wise described n. exc. 10 cm width or girth and applying one coat of Synthetic enamel paint over a coat of pink primer complete all as specified and as directed. |
| 130 | M & Lfor preparation of new or old wooden surfaces of any description not other wise described any width or girth and applying creosote oil for treating of wood complete all as specified and as directed. |
