|
| 1 | Dismantling timber scantlings 40 sq. cm and over in section, in any position, unframed work |
| 2 | Dismantlingtimber in fillets, rails, posts, rafters,purlins, etc. under 40 sq. cm in section |
| 3 | Dismantling plain or corrugated steel sheeting any thickness, complete all as specified and directed. |
| 4 | Dismantling of Wallandceilingboards(fibre, pulp, insulation, etc.) or insulationboards/slabs/ blankets, any thickness, including cover fillets. |
| 5 | Excavating over areas, nexe 1.5 deep and getting out hard soil |
| 6 | Excavating over areas, exe 1.5 and nexe 3mdeep and getting out hard soil |
| 7 | Excavating over areas, nexe 3 m and nexe 4.5m deep and getting out hard soil |
| 8 | Surface excavation n.exc 30 cm deep and averaging 15 cm deep and getting out in hard/dense soil. |
| 9 | Rough excavation not exceeding 1.5 m deep and getting out hard soil |
| 10 | Excavation in trenches n,exc 1.5 m wide and n.exc 1.5 m deep for foundation and getting out in hard/dense soil. |
| 11 | Returning/filling in including spreading, levelling, watering and well ramming in layers n exc 25 cmin hard/dense soil. |
| 12 | Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point (soil) |
| 13 | M&L for reinforced cement concrete (Nominal mix) (1:2:4) type B1 (using 20mm graded aggregate) as in slab supported on walls, beam and columns in floor, roof, landing, balcony, canopies, deck slab and in shelves and like |
| 14 | Use and waste for flat formwork to soffits of suspended slab such as roof slab, landings and similar work not exc 200mm thick (horizontal or sloping) |
| 15 | Providing & fixing false ceiling at all heights with semi perfoarated 12mm thick micro tegular edged GRG (Glass Fibre reinforced Gypsum) false ceiling tiles of Size 595 x 595 mm of approved texture, design and patterns havings moisture content less than 2%, humidity resistance of 99%, nbrc 0.50 TO 0.75 as per IS 8225 : 1987 Non combustible as per BS 476 part 4 )- 1970 and light refilectace of 85% (minimum) to be laid in ture horizontal level suspended on in terlocking metal T-Grid of hot depped galvanised iron section of 0.33mm thick (galvanized) @ 120 Grams per sqm including both sides) comprising of main-T runners of size 15x32mm of lenfth 3000 mm cross-T of size 15x32mm of length 1200mm and secondary intermediate cross T of size 15x32 mm of length 600mm to form grid module of sixe 600x600 mm suspended from ceiling using galvanised mild steel items (galvanizing @ 80 grams per sqm) i.e 50mm long,8 mm outer diameter M-6 dash fasters 6mm dia fully threaded hanger rod up to 1000 mm length and L-shape level adjuster of size 85x25x2 mm. Galvanised iron permeter wall angle of size 24x24x0.40mm of length 3000mm to be fixed on periphery wall partition with the help of palstic rawl plugs rawl plugs at 450mm centre to centre and 40mm long dry wall wood screws. the work shall be carried out as per specifications drawing and as per derictions of the Engineer - in - Charge |
| 16 | M & L for Screed bed or bedding layer of mortar 20 mm thick for laying floor finishes |
| 17 | M & L Hardcore of gauge n exc. 63 mm,(broken stone & boulders) deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface |
| 18 | M&L PCC 1:4:8 type D2(using 40mm graded aggregate) as in foundation filling and mass concrete etc. |
| 19 | M&L PCC 1:3:6 type C2(using 40mm graded aggregate) as in foundation filling and mass concrete etc. |
| 20 | M&L for providing PCC Type B1 1:2:4 (20mm graded agg) in roof kerbs or mud stops rounded or chamfered on edges |
| 21 | M&L for PCC 1:3:6 type C-1(20 mm graded aggregate) precast cement concrete block masonry with solid blocks exc 10 cm in width and setting in CM 1:6 etc complete. |
| 22 | M&L for precast cement concrete solid building blocks (1:3:6), type C-1, 10 cm thick (with plain or interlocking joints as directed) setting in cement mortar (1:4), complete, laying inner side of wall. |
| 23 | M&L for re-inforced cement concrete (nominal mix) 1:2:4 type B-1 (20mm graded aggregate) as in foundations,including rafts,plinth beams,bases for columns,etc;basement slabs,under-reamed piles and mass concrete. |
| 24 | M&L for re-inforced cement concrete (nominal mix) 1:2:4 type B-1 (20mm graded aggregate) as in beams, cantilevers, bressummers, lintels over 1.5m span complete. |
| 25 | M&L for re-inforced cement concrete (nominal mix) 1:2:4 type B-1(20mm graded aggregate) as in columns ,pillars,piers,posts and struts complete. |
| 26 | Suppiled only liquid WPC |
| 27 | U & W of Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter rough finished surfaces of concrete. |
| 28 | M & L for Second class clean swan hard-wood in scantlings complete all as specified and directed |
| 29 | M&Lsecond class hard wood plain fillets.square, rectangular or triangular in section, clean sawn, sectional area exc 13 sq cm and n exc 25 sq cm secured with nails |
| 30 | S & F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frameshall be covered with heat moulded plain colour PVC \"C\" channelhaving a PVC sheet strip of 20mm width stuckinside with solventcementfor stiles and plain colour PVC sheets for top rail, lock & bottom rail on either side & as gap insert for top rail & bottom rail, Panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement supplying & fixing in the frameat siteas per specification & drawing. |
| 31 | S&F solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, supplying and fixing in opening as per specification and drawing. |
| 32 | S& F Aluminium anodised barrel tower bolts 150mm long of extruded section and fixed |
| 33 | S&F 100mm size stainless steel butt hinges, medium weight, cold rolled complete with stainless steel screw etc. all as specified as directed. |
| 34 | S & F 150mm size extruded aluminium alloy handles, fabricated type, anodised. |
| 35 | M&L for MS TMT bars10mm dia and over, cut to lenth, bend to shape required, including cranking, bending, sprially for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips. |
| 36 | M&L for MS TMT bars 05mm dia and over, upto and including 10 mm dia in stirrups, spaces and binders. |
| 37 | S&F Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. → |
| 38 | S & F Steel ventilators with centre hung shutter including two pairs of brass cup pivots, catch spring and pulley wheel, complete. |
| 39 | S & F Anodised aluminium snap gridframe work for false ceiling allas specified |
| 40 | S & F Hangers 6 mm dia. G.I. (upto1200mm length) adjusting levelfixed to roof slabs by means ofceilling cleats made out of G.I. flat 40 x 3 mm size 60mm longand expansion hold fasteners12.5mm dia. 40mm longcomplete all as specified. |
| 41 | S&F Pre-Painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour havimg testile strenght of 550 Mpa as in roof covering/ cladding to wall , fixed with self tapping screws as specified and directed. |
| 42 | Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified |
| 43 | M&L for 6mm thick plywood, (5 Nos of ply)grade BWR, type BB, fixed with nailsto timber framework. In wall . |
| 44 | S& F Plywood 4mm thick (No of ply 03 nos), grade BWR, type BB, fixed with screws to timber frame work as ceiling. |
| 45 | Providing and fixing 10mm thickplaster of paris ceiling (Gypsumanhydrous) to flat surface over 2ndclass soft wood fillets, or metal framework and reinforced with G.I. wire mesh (Fillets, metal frame work and G.I. wire mesh paid separately). |
| 46 | M & L for 75mm thk PCC 1:3:6 type C2 (using 40mm graded stone aggregate) as cement concrete in sub base floors , sub-bases floors and pavings etc complete all as specified |
| 47 | M&L for 75 mm thick plain cement concrete type C-2, 1:3:6, (40mm graded stone aggregate)as in plinth protection, finishing the top surfaces even and smooth W/O using extra cement. |
| 48 | M&L for 100 mm thick PCC 1:4:8 type D2 (using 40 mm graded stone aggregate) as cement concrete in Sub-base floors, sub-bases floors and pavings etc complete all as specified. |
| 49 | M&L for Chequered cementconcrete tiles 20cm x 20cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors with Grey Cement and no pegmentation complete all as specified and directed |
| 50 | M&L for 40 mm thick PCC 1:2:4 type B-1(using 20 mm graded stone aggregate) as in floor finishes. |
| 51 | M & L for 350 x 250 x 7 mm/450 x 350 x 7 mm thick glazed coloured ceramic tiles on vertical surface of wallset and jointed in neat cement slurry and pointed in white/coloured cement to match the shade. |
| 52 | M & L for Non-skid ceramic coloured tiles 7 to 8 mm thick ( square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match. |
| 53 | M & L Chequered cement concrete tiles 20cm x 20cm x 25mm/30cm x 30cm x 25cmthick (with grey pigment cement & pigments), set, jointed and pointed in neat cement slurry in floors |
| 54 | M&L for 15 mm thick rendering in CM (1:4) mixed with liquid WPC 0.4% by the weight of cement over brick/concrete wall surfaces finished fair and even.Note : Liquid WPC shall be measured separately. |
| 55 | M&L for 10mm thick rendering in CM (1:6) over block/concrete wall surfaces finished even and smooth without using extra cement. |
| 56 | M&L for 15 mm thick screed bed in CM 1:6 for laying floor tiles . |
| 57 | S & F Sheet glass 4.0 mm thick, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane. |
| 58 | M&L for prepration of new wooden surfaces exc.10cm in width or girthand applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed. |
| 59 | M&L for preparation of new steel surface of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc crome complete all as specified and directed. |
| 60 | S & F 20mm 3-layer PP-R P o l y p r o p y l e n e random copolymer concealed pipes SDR 7.4PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold watersupply including all PP-R plain & brass threaded p o l y p r o p y l e n e random fittings fixed complete to walls, ceilings or in floors etc |
| 61 | S&F PP-R Gate valves 20 mm outer dia of pipes (brass insert) as per requirement of the site |
| 62 | S&F Rotational mounded polythene water storage tank of 1000 ltrs capacity,(multilayered, cylindrical, vertical with closed top) hoisted and fixed in position as specified in SSR Pt-I. |
| 63 | S & F 15mm Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered \"Hot\" or \"Cold\" with long screwed shanks and fly-nuts,screwed for iron pipe and fixed |
| 64 | S&F 15mm Bib tap standard of PTMT any colour high pressure screwed for iron pipe and fixed. (Minimum weight 15mm-90gms/20mm-125gms) |
| 65 | S & F 15mm Angle stop valve of PTMT any colour high pressure screwed for iron pipe and fixed, (Minimum weight 15mm-90gms). |
| 66 | S & FWaste coupling of PTMT (half or full threaded) (Minimum weight 32mm- 45gms/40mm-60 gms) |
| 67 | S&F Towel Rail 450mm long of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 170gms). |
| 68 | S& F PVC connections 15 mm size, 450 mm long with PTMT nuts |
| 69 | S&F 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors |
| 70 | S&F PVC (SWR) bends any radius with access door, 110mm dia. |
| 71 | S&F PVC (SWR) junction single, (single T) equal or unequal, 75mm dia. |
| 72 | M&L 75mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement |
| 73 | S & F vitreous China squatting pan, ‘Orissa\" pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) complete. |
| 74 | M&L forVitreous China urinals, bowl type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) |
| 75 | S & F PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets. |
| 76 | S & F Vitreous Cliina wash basin, wlhite, flat back, size 550x400 irun (for Hospilal use) excluding taps, waste, chain and plug and porcelain stopper but including cutting for and pinning in ends of brackets or erecting stand |
| 77 | Use & waste of form work to side and soffits of floor or roof beams, beam haunchings, girders, bressumers, lintels, cantilivers, shelves including supports, overhangs etc, also splays betweennfloors and beams etc, rough finished flat surfaces of concrete. |
| 78 | Use & waste of form work to sides of pillars, posts, struts,piers, columns and stanchios rough finished square, rectangular or polygonal surfaces of concrete. |
| 79 | M & L for second class hard wood Plain fillets cross sectional area n exc 3 sq cmsquare, rectangular or triangular in section, clean sawn, secured with nails or brads. |
| 80 | M&L for preparation of newly plastered surfaces of walls and applying three coats of white washcomplete all as specified and directed. |
| 81 | M&L for preparation of newly plastered surfaces of walls and applying two coats of cement based paint complete all as specified and directed. |
| 82 | M/L for point wiring in casing caping with 1.5sq mm FRLSHPVC insulated unsheathed single core multithreaded copper conductor cable 1100 volts grade incl 1.5 Sq mm PVC insulated unsheathed copper conductor cable as earth continuity conductor drown through in and incl casing caping with its accessories pressed steel terminal box incl 3mm thick ISI marked laminated sheet cover for fixing switches/socket/regulators etc for the following: One light/fan point controlled by one No piano type switch5 Amps single pole one way |
| 83 | One socket outlet 5/3 pin 6 AMPS controlled by one switch on the same board. |
| 84 | S&F Switch Piano Flush button single pole one way 5/6 Amp. |
| 85 | S&F socket outlet 2 in 1,3 pin & 2 pin, 5/6 Amp, 240 volt. |
| 86 | S&F ceiling rose surfacebakelite 65mmx50mm 100watt three terminal. |
| 87 | S&F sheet metal enclosure double door for MCB DB single pole and neutral 4 way with 200 Amps rated bus bar 240 volts double door (Metallic) typeincluding taking down old Distribution Board and MCBs all as specified and directed . |
| 88 | S&F MCB SPN 16 to 32 Amps 240 volts \"C\" series, 10 KA, 50 Hz.Make:- As approved Make of DB |
| 89 | S&F MCB SP 5 to 32 Amps 240 volts \"C\" series, 10 KA, 50 Hz including connection in the DB and testing/commissioning.Make:- As approved Make of DB |
| 90 | Supply and fixing LED lights fitting 1x 18W, 4 feet, 220V,AC decorative box type with driver, holder including LED light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete. |
| 91 | S & F Lamp holder, PVC/Polycarbonate type with back plate suitable for battern fittings complete. all as specified and directed by as engineer-in-charge. |
| 92 | S&F LED Bulb 9 watt cat part noLED ADORE 9W B22 WW 2 STAR LAMPcomplete all as specified and as directed by engineer-in-charge. |
| 93 | Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300msweep with, blades, and frame and louvers |
| 94 | Supply and fixing LED light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete. |
| 95 | Material and Labour for earthing complete with galvanized steel earth plate electrode 600 x 600 x 6 mm thick buried directly in ground( earth pit not less than 2.25 meter deep below ground level) with top edge of plate not less than 1.5 meter below normal ground level, connected to galvanised earth lead wire 4.0mm diaby means of bolts, nuts, check nuts and washers ofgalvanizediron or steel, all as shown in electrical plate No 3 of SSR Pt I including necessary excavation and earth work PCC(1:3:6) type C-1 with 50 mm thick pre cast RCC ( 1:2:4) type B-1 cover slab framed with 50X30X4 mm MS angle (reinforced with 6 mm dia deformed bar @ 15 cm C/C both ways and suitable handle of 10 mm dia round bar) including providing charcoal or coke and magnesium sulphate in alternate layers of 15 cm compacted thickness all around the earth electrode, with funnel and 20 mm bore galvanized iron watering pipe (medium grade) wire mesh, copper lugs, complete in all respect., GI earth wire protected by 40 mm bore (light grade) galvanized iron pipe and other end connected to the earth bar (test point) made of MS flat (400X32X6 mm) bend in ‘D’ shape and fixed to wall by means of fast nut or bolt grouted in to wall at 1 mtr from plinth height. 4sqmm PVC insulated (colour green) copper conductor single run as earth continuity conductor along with 15 mm PVC conduitgrouted in wall or fixed on wall surface to be continued up to main switch board and fix with common earth dolly as directed by EIC . Disposal of soil to a distance not exceeding 50 mtr and necessary testing on completion complete all as specified and as directed. |
| 96 | Supply and laying or fixing or passing through pipeXLPE insulated, armouredheavy duty electric cable with aluminium conductor, 1100 volts grade of size 10 sqmm 2 core complete all as specified and directed by Engineer in charge. |
| 97 | S&F high density polyethylene pipes (HDPE) of pressure rating 6Kgf/cm2 laid in trenches of size 50mm dia all as specified and directed by Engr-in-Charge. |
