|
| 1 | Taking down cement plaster on block masonary or concrete surfaces including raking out joints, hacking for keys, scrubbing down with water etc. complete all as specified and as directed. |
| 2 | Demolition of cement concrete in ground floors and pavings not exceeding 15 cm thickness (below or above ground level) and disposing of debries outside MD land complete all as specified and as directed. |
| 3 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premisescomplete all as specified and as directed. |
| 4 | Dismantling stone slabs and tiles of any description or thickness in floors, aprons etc. laid, bedded and pointed in any mortar complete all as specified and as directed by Engr-in-Charge. |
| 5 | M&L for 15mm thick rendering in cement mortar (1:4) on fair faces of brick or cement concrete surfaces, finished even and smooth without using extra cement complete all as specifed and as directed. |
| 6 | M&L for preparation of new surfaces of wall and applying two coat of oil bound distemper over a coat of primer complete all as specified and as directed. |
| 7 | M&L for preparation of old surfaces of wall by applying 2-3 mm thick white cement base putty in patches as required and applying two coats of oil bound distemper complete all as specified and as directed. |
| 8 | M&L for 25mm thick PCC (1:2:4) type B0 (using 12.5mm graded stone aggregates) in sub floors complete all as specified and as directed by the Engr-in-Charge. |
| 9 | M&L for factory made vitrified, heavy duty, parking tiles, coloured, matt finish, unglazed and unpolished of size 300mm x 300mm x 10mm thick including 15mm thick screed bed in CM (1:4) complete all as specified and as directed by Engr-in-Charge. |
| 10 | M&L for 75mm thick PCC (1:4:8) type D2 (using 40mm graded stone aggregates)as in sub base complete all as specified and as directed. |
| 11 | M&L for providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour, design and pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness and size/ shape, made by table vibratory method using PU mould, laid in required colour and pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; complete all as specified and as directed. |
| 12 | M&L for 75mm thick plain cement concrete (1:3:6) type C1 (using 20mm graded stone aggregates) as in plinth protection, laid in pannels including necessary formwork, finished even and smooth without using extra cement complete all as specified and as directed. |
| 13 | M&L for glazed ceramic coloured tiles of size 350mm x 250mm x 8-10mm/ 450mm x 300mm x 8-10mm/ 300mm x 600mm x8-10mm thick over and including 10mm thick rendering in cement mortar (1:4) as in backing coat for tiles on vertical surfaces, set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specifed and as directed. |
| 14 | M&L for coloured, non skid ceramic tiles7 to 8mm thick (squares/ rectangular), area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, over and including 15mm thick screed bed in CM(1:6) complete all as specified and as directed. |
| 15 | M&L for vitrified, light shade coloured tiles9-10 mm thick (squares/ rectangular), area of each tile exceeding 0.11 Sqm but not exceeding 1.00 Sqm in floors etc.set and jointed in neat cement slurry and pointed in white or coloured cement to match, over and including screed bed or bedding layer of mortar 15 mm thick in cement mortor (1:6) complete all as specifed and as directed. |
| 16 | M&L for vitrified, light shade coloured tiles 9-10 mm thick (squares/ rectangular), area of each tile exceeding 0.11 Sqm but not exceeding 1.00 Sqm in skirting etc.set and jointed in neat cement slurry and pointed in white or coloured cement to match, over and including 10mm thick plastering in CM (1:4) as in backing coat of tiles complete all as specifed and as directed. |
| 17 | M&L for granite of 18 to 20 mm thick, work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite and moulding edges as directed including screed layer of 15mm thick in CM (1:4) complete all as specified and as directed. |
| 18 | M&L for machine cut kota stone slab flooring 20-25mm thick over cement screed base, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing including screed layer of 15mm thick in CM (1:4) complete all as specified and as directed. |
| 19 | M&L for Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed including 10mm thick rendering in cement mortar (1:4) as in backing coat complete all as specified and as directed. |
| 20 | Providing edge moulding to 18-20mm thick stone/ granite etc. of counters vanities, staircase, shelf etc. including machine polishing to edge to give high gloss finish etc. complete all as specified and as directed. |
| 21 | M&L for renewing tiles of any typein patches area n. exc. 5.00 Sqm including removing and cleaning old tiles, preparing beds and laying or setting, jointing and pointing new ceramic tiles to match the existing floor/ wall complete all as specified and as directed. |
| 22 | S&F in repairs CP bib taps, fancy type, 15mm bore, cast copper alloy with crtuch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and as directed. |
| 23 | S&F in repairs CP pillar taps, fancy type, 15mm bore, cast copper alloy, with capstan heads screwed down high pressure, with or without lettered `Hot\" or `Cold\" with long screwed shanks and fly-nuts, screwed for iron pipe complete all as specified and as directed. |
| 24 | S&F in repair stop valves/ angle valves 15mm bore, fancy type, CP, cast copper alloy screwed down high presure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and as directed. |
| 25 | S&F in repairs vitreous china wash basin, white, flat back. size 550mm x 400mm excluding taps, waste chain and plug and porcelain stopper but including brackets complete all as specified and as directed by Engr-in-Charge. |
| 26 | S&F in repair sink with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and waste; including bedding in CM to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm, bowl size 410mm x 330mm x 160mm complete all as specified and as directed. |
| 27 | S&F in repair sink made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm, bowl size 410mm x 330mm x 160mm complete all as specified and as directed. |
| 28 | S&F in repairs PVC valveless, syphonic action type, flushing cistern 10 litr capacity, low level, white, with intel, ball valve, float and handle including brackets complete all as specified and as directed. |
| 29 | S&F in repairs600mm x 450mm mirror of selected quality glass 5-6 mm thick and fixed to walls with necessay PVC frame complete all as specified and as directed. |
| 30 | S&F in repair mirror of 5-6 mm thick glass with double coat of protection and longevity grounded edges for safety and silver plating on the back for better reflection including with stainless steel decorative fastener/ studs complete all as specified and as directed. |
| 31 | S&F in repair vitreous china wash down water closet pan (pedestal pattern), white (excluding flushing cistern and flush pipe) white including necessay fitting etc. complete all as specified and as directed. |
| 32 | S&F in repair vitreous china urinal, half stall type, white, complete including providing and fixing plugs, bedding urinal against wall in cement mortar (1:2), securing urinal to plugs with and including 60cm long brass screws, pointing around urinal back in cement, with grating and union for discharge pipe and PVC waste pipe, including making all connections to existing connections, fixed complete all as specified and as directed. |
| 33 | S&F in repair brass chromium plated urinal spreader, fancy type of approved quality fixing with 15mm dia pipe complete all as specified and as directed. |
| 34 | S&F in repairs internal flushing cistern kit, washer, flushing handles etc. complete all as specified and as directed. |
| 35 | S&F in repairs PVC flush bend pipe upto 40mm dia for PVC 10 litre flushing cistern suitable for EWC/ IWC complete all as specified and as directed by Engineer-in-Charge. |
| 36 | S&F in repair 15mm bore pillar taps of PTMT, any colour, high pressure, screwed for iron pipe and fixed (minimum weight 15mm-110gms) complete all as specified and as directed. |
| 37 | S&F in repair 15mm bore bib tap standard of PTMT, any colour, fancy type, high pressure, screwed for iron pipe and fixed (minimum weight 15mm-105gm complete all as specified and as directed. |
| 38 | S&F in repair 15mm bore bib tap standard of PTMT, any colour, fancy type with long body, high pressure, screwed for iron pipe and fixed (minimum weight 15mm-120gm) complete all as specified and as directed. |
| 39 | S&F in repair 15mm bore pillar tap standard of PTMT, any colour, fancy type, high pressure screwed for iron pipe and fixed (minimum weight 15mm-120gm) complete all as specified and as directed. |
| 40 | S&F in repair 15mm bore angle valve/ stop valve of PTMT, any colour, high pressure, screwed for iron pipe and fixed (Minimum weight 15mm-90gm) complete all as specified and as directed. |
| 41 | S&F in repair 20mm bore ball valve, high pressure, of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed (minimum weight for 20mm – 210 gms) complete all as specified and as directed. |
| 42 | S&F in repair PVC connection 15mm size with PTMT nuts of length 450mm complete all as specified and as directed. |
| 43 | S&F in repair PVC water closet seat cover, black or white, closed pattern, with flat bottom and cover and mild steel chromium plated or aluminised hinging device complete all as specified and as directed. |
| 44 | S&F in repair health faucet (ABS body), mild steel chromium plated, suitable for 15mm dia pipe with 1.25 meter long flexible tube and ABS wall hook including making connection and fixed in position complete in all respect as specified and as directed by Engr-in-Charge. |
| 45 | S&F in repair CP grating of size 100mm dia with/ without waste hole complete all as specified and as directed. |
| 46 | S&F 15mm bore GI tubing, medium grade with all fittings, fixed to walls, ceiling or laid in floors including taking up or down existing unserviceable steel tubing and connections complete all as specified and as directed. |
| 47 | S&F 20mm bore GI tubing, medium grade with all fittings, fixed to walls, ceiling or laid in floors including taking up or down existing unserviceable steel tubing and connections complete all as specified and as directed. |
| 48 | M&L in repairs 32mm dia, 800mm long flexible PVC waste pipe complete all as specified and as directed. |
| 49 | S&F polyethylene water tank cover suitable for upto 1000 Ltres capacity water tanks including taking down old water tank cover complete all as specified and as directed. |
| 50 | S&F in repair 75mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed. |
| 51 | S&F in repair for 110mm bore PVC (SWR) pipes, single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed. |
| 52 | S&F in repair 110/ 150mm bore PVC (SWR) pipes, single socketed, in any length with rubber ring joints, fixed to walls complete all as specified and as directed. |
| 53 | S&F in repair PVC (SWR) bends of any radiusm 75mm bore complete all as specified and as directed. |
| 54 | S&F in repair PVC (SWR) bends of any radius 110mm bore complete all as specified and as directed. |
| 55 | S&F in repair kitchen plate rack with four shelves made out of stainless steel sheet 1mm thick, over all size 90cm x 60cm x 25cm complete all as specified and as directed. |
| 56 | S&F in repair PVC bathroom mirror cabinet 350mm x 450mm x 150mm, 1st quality, fixed with necessary screws complete all as specified and as directed. |
| 57 | S&F in repair 15mm bore gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as directed. |
| 58 | SF in repair 20mm bore gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as directed. |
| 59 | S&F in repair 15mm bore, 2 way, CP bib cock with wall flange complete all as specified and as directed. |
| 60 | S&F in repair CPVC pipes 25mm dia (outer dia), SDR 11 and plain CPVC SDR 11 fittings on walls/ ceiling or laying in floors complete all as specified and as directed. |
| 61 | S&F in repair CPVC pipes 20mm dia (outer dia) SDR 11 and plain CPVC SDR 11 fittings including tee, bend etc. on walls/ ceiling or laying in floors complete all as specified and as directed. |
