Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | M&L for preparing structural soundness report by performing following Test :-(i) Visual inspection and record of photography - 30Nos Pics(ii)Ultrasonic pulse velocity test for RCC structure in accordance with IS:13311 Part-1 1992 by portable ultrasonic non destructive digital test equipment including chipping out plaster.- 12Nos.(iii)Rebound hammer test :- Rebound hammer test in accordance with IS:13311 Part-2 1992 by non destructive digital test equipment min- 48 Nos(iv) To check & confirm present status of structure on basis on NDT results , visual inspection. & To provide recommendation for structrue repairs.(v) To Preparing Structure soundness report etc.-3 Set(vi) The work to be carriedout by NABL approved Lab. |
| 2 | M&L for 20 to 25mm thickchipping and removing of loose concrete (weak concrete) with power driven pressure type pnuematic chisel of standard pnuematic make to reach sound concrete and to completely exposing the existing reinforcement, for any height (including necessary scaffolding and necessary arrangements for temporary support to existing structure,jet wasing& cleaning of of exposed surface) strictly as per the requirement of repair material and as directed by Engr-in-Charge. |
| 3 | M&L for 40 to 50mm thickchipping and removing of loose concrete (weak concrete) with power driven pressure type pnuematic chisel of standard pnuematic make to reach sound concrete and to completely exposing the existing reinforcement, for any height (including necessary scaffolding and necessary arrangements for temporary support to existing structure,jet wasing& cleaning of of exposed surface) strictly as per the requirement of repair material and as directed by Engr-in-Charge. |
| 4 | M&L for Removing of rust from existing steel surfaces with rust removers of SIKA Rustoff100/Rebaklens/Asian of Fosroc or eqvivalant applied in two coats as per manufacturer instructions Min @ 0.15 kg/sqm per coat and cleaning all rust with steel wire brush and washed with water as directed by Engr-in-Charge.Note :- 1.The work will be carried out by authorized aplicater of SIKA/Fosroc/Asian/Dr.Fixit as approved by GE.2. The work will carried out on any type of concrete strucure i.e. Diving Pool,Swimming pool incl column,Beams,Slabs & walls.3.The necessary scafolding will be deemend to incl in the rate quoted by the contractor. |
| 5 | M&L for application of anti corrosive coating to Reinforcement by applying zinc rich epoxy based protective coating on the exposed reinforcement after proper mixingapplied min @ 0.25 kg/sqm of steel surface complete as per manufacturers specification and directed by Engr-in-Charge. Make : SIKA Rustop/friazinc/FerroGard®-950, Fosroc: Nitozinc /Nitocoat/Asian Paints or equivalent as approved by GE.Note :- 1.Application of the products shall be by manufacturer’s authorized applicator and as per manufacturer\"s specifications complete all as specified and directed.2. The work will carried out on any type of concrete strucure i.e. Diving Pool,Swimming pool incl column,Beams,Slabs & walls hence necessary arrengements for scafolding, T&P shall deemed to be incl in rate quoted by the contractor. |
| 6 | M&L for providing L-shaped shear connector with rebar of 10mm dia and average 150mm long to 25 to 40 mm projection @ 1 no per sqm of Surface area of Beam/Column/Slab etc complete including drilling upto required depth, fixing it with required chemical Hilti HY-200 or equvalant. Make : Hilti HY-200 or fissure of equvalent grade as approved by GE.Note :- 1.Application of the products shall be done by manufacturer’s authorized applicator and as per manufacturer\"s specifications complete all as specified and directed.2. The work will carried out on any type of concrete strucure i.e. Diving Pool,Swimming pool incl column,Beams,Slabs & walls hence necessary arrengements for scafolding, T&P shall deemed to be incl in rate quoted by the contractor. |
| 7 | M&L for appication of Epoxy resin bonding agent for concrete surface min @ 0.5 kg/sqm with Nitobond EP of Fosroc or Sikadur 32 LP of Sika complete as per manufacturers specification or as directed by Engr-in-Charge.Make : SIKA Sikadur 32 LP IN, Fosroc Nitobound EP/Asian Paintor equivalent as approved by GE.Note :- 1.Application of the products shall be by manufacturer’s authorized applicator and as per manufacturer\"s specifications complete all as specified and directed.2. The work will carried out on any type of concrete strucure i.e. Diving Pool,Swimming pool incl column,Beams,Slabs & walls hence necessary arrengements for scafolding, T&P shall deemed to be incl in rate quoted by the contractor. |
| 8 | M&L injection groutingof low viscosity epoxy groutwith Sikadur 52 or 53 (Make : SIKA/ BASF) including drilling hole @ 50 cm centre to centre (approx) of required dia in RCC slab,beam,walls and column with power drill and fixing metalic/pvc NRV packer Min 100mm or upto required depth grouting shall be done with mechanical pressure pump of pressure 8 to 10 Kg / Sq Cm. (Note: Paymment shall be made on basis of net weight of epoxy grout injected.)Make : Sika :Sikadur 52 & 53,Fosroc: Conbextra EP10 or equivalent as approved by GENote :- 1.Application of the products shall be by manufacturer’s authorized applicator and as per manufacturer\"s specifications complete all as specified and directed.2. The work will carried out on any type of concrete strucure i.e. Diving Pool,Balancing Tank,Swimming pool incl column,Beams,Slabs & walls hence necessary arrengements for scafolding for desired height,depth,andT&P shall deemed to be incl in rate quoted by the contractor. |
| 9 | M&L for non shrinkable factory designed pourable high performance micro concrete of M40 grade(using polymer enriched cement compresive strength >65N/mm2 and 8-10mm agregate as per manufacturer design) for micro concreting and jacketing applications of RCC walles,columns, beams, and concrete slab etc repairs.Make : UltraTech MICROKRETE is a polymer enriched cement/Sika :SikaRep Microcrete/ Fosroc:Micro concrete or equivalent as approved by GE.Note :- 1.Application of the products shall be by manufacturer’s authorized applicator and as per manufacturer\"s specifications complete all as specified and directed.2. The work will carried out on any type of concrete strucure i.e. Balancing Tank,Diving Pool,Swimming pool incl column,Beams,Slabs & walls hence necessary arrengements for scafolding, T&P shall deemed to be incl in rate quoted by the contractor.3.Min Cment content shall be as per IS/Manufacturer instructions. |
| 10 | M&L 25 mm thick shotcreting by mechanical means in RCC column, beam and soffit of RCC slab with approved M-25 Design mix ( using 10mm and below graded stone aggregate )using polypropelene macrofibre 6mm long &upto 6mtr hieght from floor level, including all necessary scaffoldingand props required to support the slab at required spacing up to the required height , machinery required, minimum pressure of shotcrete at nozzle shal not be less than 40 PSI and finished to uniform thickness with straight edge also includingGI wiremesh weightnot less then 2.4 Kg /Sqmand fixed to shear connectors with MS wire including making all necessary arengment for covering of walls & floors with PVC sheet / tarpaulin to protect the surface from any damage due to shotcreting alongwith suitable ply board plateform at a height of 3 to 4 m above floor level including all necessary support wooden prpos and suitable frame work to support the plateform etc complete all as specified and directed. |
| 11 | M&L for providing rendering with PMM (Polymer modified cementitious mortar) with following :-(i) Dry sub strate surface and free of debris & dust(ii) Applying Epoxy bond coat on the sound substrate using approved spray machine & ensuring that no pin holes are visible.(In case pin holes are still visible after a coat, a second coat shall be applied to ensure absence of pin holes).(iii) Immediately after application of epoxy bond coat as above apply PMM (Polymer modified cementitious mortar) of 25 mm thickness.Note :Application of PMM shall be preferably be in coats of appx 10mm thickness. PMM work shall be executed in fairely rapid successions so as entire work is completed with in 30 mins). PMM shall be pre packed ready to use.(iv) PMM surface to be moist cured for three days followed by air curing in temperature as recommended by manufactuer complete all as specified and directed. (v) The item includes cost towards supply and application all complete.Mixing and Application of the products shall be by manufacturer’s authorized applicator and as per manufacturer’s specifications complete all as specified and as directed.Make:- Sika Top-122 HS/ Fosroc or equivalent.Notes : The Area includes in this items for repair work of diving pool, Balancing Tank,Steps,Beams, Columns upto 9m high/Deep hence necessary scaffolding and all other arrengments deemds to includes in the rates qotoed by the contractor. |
| 12 | M&L for applying curing agent by sprey on concrete surface @ 0.5kg/sqm with make SIKA Antisol EWP or Equivalent grade of BASF / FOSROC complete all as specified and directed |
| 13 | M&L for Non Toxic Food grade epoxy stearate protective coating shall be Nitocote EP405/Asian/Sikaof 200 micron DFT, a two pack epoxy coatingpecific ally designed for contact with potable water. The cured film shall comply with the requirements ofIS:9833 – 1981.Notes : Application Area : Underground Water Tanks 6m deep.The Rate incl necessary scaffolding and all other arrengments.The work to be carriedout by authorized aplicater. |
| 14 | M&L for complete removing of existing surface fineshes and Providing and applying high performance anticarbonation coating of min 200 micron thickness Deckguard E 2000 with 2mm static crack bridging ability,co2 diffusion resistance, chloride ion resistance complete all as per manufacturer instructions and as directed by Engr-in-Charge.Make:- Sika / Fosroc/Asian or equivalent.Notes : The Area includes in this items for repair work of diving pool, Balancing Tank,Steps,Beams, Columns upto 9m high/Deep hence necessary scaffolding and all other arrengments deemds to includes in the rates qotoed by the contractor. |
| 15 | M&L for Mild steel TMT bars 10mm dia & over,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips complete all as specified and directed. |
| 16 | M&L for Mild steel TMT bars 6 mm to 8 mm dia., cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips complete all as specified and directed. |
| 17 | M&L for Mild steel TMT bars upto 10mm dia., cut to length, bent to shape required, as in stirrups, spacers and binders complete all as specified and directed. |
| 18 | M&L for Formwork for fair finished concrete surface to sides of pillars,posts, struts, piers, columns and stanchions etc. complete all as specified and directed.Note : - Formwork should be compatible for microconcrete ie leakproof, fair finish surface and required for divingpool structure. |
| 19 | M&L Formwork for Fair finished concrete surface to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup-ports, overhangs, etc. also splays between floors and beams, etc. complete all as specified and directed.Note : - Formwork should be compatible for microconcrete ie leakproof, fair finish surface and required for divingpool structure. |
| 20 | M&L Formwork for Fair finished concrete surface to soffits of suspended slab such as roof slab/lintel band and similar work n. exc 300mm thick (horizental or sloping) fair finished surface complete all as specified and directed.Note : - Formwork should be compatible for microconcrete ie leakproof, fair finish surface and required for divingpool structure, rate quoated by the contractor demeed to incl scaffolding for any heights upto18m. |
| 21 | S&F for Formwork to fair finished faces of walls,retaining walls, abutments,parapets and staircase railingsand similar work including attached pillasters, buttresses, etc.; vertical or to batter complete all as specified and directed. |
| 22 | M&L RCC 1:1.5:3 type B0 in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves,chajjas,facia etc complete all as specified and as directed. |
| 23 | Taking down cement plaster on brick or concrete surfaces, parapets including raking out joint, hacking for key, scrubbing down with water etc complete all as specified andas directed. |
| 24 | M&L for rendering 10 mm thick in CM (1:3) on RCC Chajja / Facia over 20mm thick in CM 1:4 as dubbing coat etccomplete all as specified and as directed |
| 25 | M&L for 10mm thick cement plaster in cement mortar (1:4) on on ceilings of concrete surfaces, including finishing surface even and smooth without using extra cement complete all as specified and directed . |
| 26 | M&L for rendering 15mm thick in CM 1:4 on fair faces of brick or concrete surface of wall andfinished even and smooth without using extra cement complete all as specified and as directed. |
| 27 | M&L for rendering 10 mm thick in CM ( 1:6 ) on fair faces of wall/ concrete surfaces finish even and faircomplete all as specifiedand directed. |
| 28 | Demolition of brick work built in cement mortar including all quions ,arcches , pillars etc complete all as specified and as directed. |
| 29 | M&L brick work in CM ( 1:6 ) with using sub class `B ` modular brick straight or curved on plan exceeding 6.0mtr mean radius complete all as specified anddirected. |
| 30 | Taking down shuters of any description nexc 1 sqmeach and removing from site complete all as specified and as directed. |
| 31 | Taking down shuters of any description exc 1 sqm but n.exe 2 sqm each complete all as specified and as directed. |
| 32 | Taking down chowkhats or frames with shutter (with out taking off shutters from the frame) area n. exc 1.5 sqm each complete all as specified and as directed. |
| 33 | Taking down chowkhats or frames with shutter (with out taking off shutters from the frame) area exc 1.5 but nexc 4.0 sqm each complete all as specified and as directed. |
| 34 | S&F for factory made solid PVC door frame of size 50mm x 47mm made out of plain 5mm plain colour PVC sheet reinforced with ms square tube, with wooden grain printed PVC sheet used inserted of plain colour PVC sheet & edges will be painted to match with printed sheet complete all as specified and as directed. |
| 35 | S&F for factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of ms tubes for top & bottom rails.MS frame shall be covered with heat moulded plain colour PVC \"C\" channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colourPVC sheet for top rail, lock rail & bottom rail. Panelling of plain colourPVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, complete all as specified and as directed. |
| 36 | Preparation of new wood and wood based surfaces of any description not other wise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer. |
| 37 | S & F for galvanised Stainless steel wire cloth of0.36mm dia wire and average width of aperture 1.4mm & fixed with tacks of stainless steel wire staples,etc complete all as specified and as directed. |
| 38 | S & F in repair galvanised Stainless steel wire cloth of0.36mm dia wire and average width of aperture 1.4mm & fixed with tacks of stainless steel wire staples,etc complete all as specified and as directed. |
| 39 | S&F in repair fabricating anodised aluminium frame work,door shutter ,windows , ventilators, partisions with one or more rebates sections of approved tint as required for partions including beading,cleat, screws,fasteners, plugs, for fixing with wall/ceiling columns/beams etc complete all as specified and directed. |
| 40 | S&F anodised aluminium window and ventilator shutters, sliding/Sidu hung type without sash bar alu section weighing 0.55 kg/m including necessary locking arrangement, guide wheels, joining cleats, glazing clips rubber packing anodised alu snap beading screws etc complete all as specified and directed. |
| 41 | S & F Powder coated aluminium sliding glazed windows with three track shutter sliding (two shutters glazed/Glass and one shutter wire mesh)with following specification complete all as specified and as directed by Engineer-in-charge.(i) Windows frame of cross section 101mm x 44mm (ii) Three way track for sliding shutters of cross section 91.8mm x 31.75mm (iii) Sliding shutter frame of cross section 40 x 18mm(iv) 4 mm thick glass superior quality. (Min)(v) LDPE Rubber guasket for fixing of glass.(vi) Locking cleats per shutter -01 Nos. (Min)(vii) Sliding rollers per shutter - 04 Nos. (Min)(viii) Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm for shutters 01 Nos.Note- (a)Thickness of Aluminium Section shall be minimum2 to 3mm (Final Thickness and Cross Section ofAluminium sectionof higher size without any extra cost shallbe approvedEngineer in Charge as per Site requirement (b) Drawing /size of window shallbe provided by Engineer in Charge during execution of work as per site requirement. |
| 42 | S&F in anodised aluminium door shutters, aluminium section weighing min 0.55 Kg/m including necesssary joining cleats, glazing clips, rubber neoprene packing handles 2 Nos in each door, pad lock, hinges, anodised aluminium snap beading screws etc complete all as specified and directed. . |
| 43 | M&Lsheet glass ordinary quality 4mm thick and glazing with oil putty in squares. not exc 0.5 Sqm eachcomplete all as specified and as directed. |
| 44 | S&F in repair aluminium (extructed section) Door closer hydraulically regulated, desingnatin No. 3, universal type, suitable for door shutter and fixed complete all as specified and directed. |
| 45 | S&F in repair double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified and directed. |
| 46 | Hacking out old broken glass( any tickness size ,quality or description ) from wooden frame or stone etc and S&F 3.00 mm thick sheet glass ordinary quality and glazing with oil putty or wooden beading in square not exceeding 0.50 sqm in each panes complete all as specified and directed. |
| 47 | S&F 100 mm Butt hinges medium weight cold rolled mild steel and fixed complete all as specified and directed. |
| 48 | S&F 150 mm long Aluminum anodized barrel tower bolts of extructed section complete all as specified and directed. |
| 49 | S&F aluminum alloy handles fabricatedanodised of 150 mm long complete all as specified and directed. . |
| 50 | S&F in repair 150 mm long floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring and rubber piece in floor, etccomplete all as specified and directed. |
| 51 | S&F 12 mm thick frosted toughned glass fixed on patch hinges/pivot for smooth functioning in door shutter,parition inc stainless steel handle of 8 inches long anfd mortice locking arrangement complete all as specified and directed |
| 52 | S&F for 18 mm thick factory made PVC sheet(600kg/m3 density) one side pre-laminated sheet shelf cup board, cabinet shutter. The 18mm thick sheet shutter bent at 90 degree and finish all edges at level for marking edge lipping bending for 0.5 mm thick PVC sheet lipping at all four edges using bonding tape etc complete all as per specified and directed. |
| 53 | S&F stainless steel shelf closing hinges 75 mm size for PVC door shutters complete all as specified and directed |
| 54 | S&F 50 x 15 mm size magnet door catcher for closing for PVC door shutter complete all as specifid and directed . |
| 55 | S& F 100 mm size MS mat/glossy finish handle complete all as specfied and directed . |
| 56 | S & F in repair curtain rails 20 mm dia, decorative type, stainless steel including fixing brackets in both sides fancy type complete all as specified and directed.. |
| 57 | Dismantling Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified |
| 58 | S&F in 5 mm thick high pressure compact laminate (HPCL) minimum density 800kg/Cum, HPCL sheet are providing higher endurance and spectacular design forwalls facade and enhance the over all stability of facade structure inc all fittings |
| 59 | M&L for Solid PVC Wall Lining/panelling consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing |
| 60 | M&L in repair 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing. |
| 61 | S&F MS work as in doors or gates, water staging, windows, ventilators of angle/rectangular or square hollow section or other section with gusset plates, rails, braces etc complete, drilled for fixing of steel sheeting or other coveringdoors, windows, ventilators etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door, window, ventilator fittingsand hanging, also fastening and fixing conforming to Fe 410-W (Gde-E-250) quality \"A\" complete all as specified and as directed by Engr-in-Charge |
| 62 | M&L for removing existing treatment with mechanical sander (rpm 1500-2700)along with dust extraction system for clean environment certified by reputed paint manufacturers, then washing the surface with Bleaching powder solution for treatment of fungal growth and preparation of surface for primmer/Putty complete all as specified and prescribed by manufacture of paint and as directed at site by Engineer-in-Charge. |
| 63 | M&L three coats of white wash on ceiling on new plastered surfaces including preparation of surfaces complete all as specified and as directed |
| 64 | M&L Two coats of white wash on ceiling on old plastered surfaces including preparation of surfaces complete all as specified and as directed |
| 65 | M&L forplaster surface of wall and and applying 2mm thick cement base waterproof wall care putty in two coat (each coat not less than 1mm) over on walls and surface finished even and smooth with sand paper completeall as specified and directed. |
| 66 | M&L for preparing plastered/Putty surface of walls and applying two coat of oil bound distemper white or any tint etc complete as specified and directed |
| 67 | M&L for preparation of plaster/Putty surface of walls and applying a priming coat of exterior weather proof primer applied Min @ 1.20 Lit /10 sqm on External walls by spray and finished the surface even and smoothcompleteall as specified and directed.Note:(1) Painting is to be carried out upto 15.00m height .The contractor is advised to visit the site before quoting the tender.The rate quoted by contractor will deemned to be inclusive of necessary sacffolding work etc as required.(2) Primig coat should be done as per manufacturer reqmt of weather proof paint. |
| 68 | M&L for two coats of Exterior weather proof acrylic Emulsion paint (Two or more coat applied @ 1.67 ltr/10 sqm) using roller/spray and make the surface smooth all as specified and prescribed by manufacturer of paint and all as directed at site by Engr-in-Charge Note:- putty shall be measured separately & Periodicalis to be carried out upto 15.00m height .The contractor is advised to visit the site before quoting the tender.The rate quoted by contractor will deemned to be inclusive of necessary sacffolding work etc required at site |
| 69 | M&L for applying Asian Royal play textured paint@ 3.28 ltr/10 sqm) over and including priming coat of primer applied @ 2.20kg/10 sqm over prepared surface of wall with white cement base putty and design approved by Engineer-in-chargecomplete all as specified and directed. Note-Putty&primershall be measured and paid seperately. |
| 70 | M & L for preparation of plastered/Puttysurfaces of walls and applying two coat of Ist quality interior plastic Emulsion paintwhite/colouredover prepared surface of wall with putty complete all as specified and directed. (Note:- Putty&primershall be measured and paid seperately) |
| 71 | M&L for Preparation of old painted surfaces of wood/wood based materials exc 10cm width or girth and applying two coat of 1st qualitysynthetic enamel paint as directed and specified. |
| 72 | M&L for Preparation of old/New painted surfaces of steel based materials exc 10cm width or girth and applying two coat of 1st qualitysynthetic enamel paint as directed and specified. |
| 73 | Demolition of cement concrete in ground floor and paving not exceeding 15cm thick ( below or above ground level ) complete including removal of debries out side MD land all asspecified and as directed . |
| 74 | M&L for 25 mm thick PCC (1:2:4) type B-1 using 20.00 mm graded crushedstone aggregate as in sub base, levelling course, etc complete all as specifiedand as directed. |
| 75 | M&L forPCC1:4:8 type D-2 using 40mm graded stone aggregate as in sub base of floor, etccomplete all as specified and directed |
| 76 | M & L for 75mm thick cement concrete 1:3:6 type C1, with using 20mm graded stone aggregateas in floor/ plinth protection finish the surface even and smooth with using extra cement including filling the expansion joints with bitumen filler / filler boards and necessary form work etc complete all as specified and as directed. |
| 77 | Dismantling of floor, hearth , or wall tiling including cement mortar bedding ( but not backing )and rubbish of the primeses complete all as specified and directed. |
| 78 | M&L for scratch free, vitrified ceramic tiles9 to 10mm thick (square or rectangular) area of each tile not exceeding 0.36 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed or bedding layerin CM 1:6 complete all as specified and as directed.Make of tile : Superior quality tiles from Kajaria/Somany/Orient Tiles. |
| 79 | M&L for non skidceramic colouredtiles 7-8mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exc 0.16 sqm in floors etc set and jointed in neat cement slurry and pointed in white or colouredcement to matchand including 15mm thick screed bed or bedding layer in CM 1: 6 complete all as specified and as directed. |
| 80 | M&L for glazed ceramic coloured tiles of size excthan 0.06 sqm to 0.14 Sqm thick as on vertical surfaces such as wall, dado ,skirting etc set and jointed in neat cement slurry and pointed with coloured cement to match over 10 mm thickbacking coat on fair faces of brick work in CM (1:4) complete all as specified and as directed. |
| 81 | Demolition of Stone slabs and tiles of any description or thickness in floors complete all as specified and as directed. |
| 82 | M & Lfor machine cut kota stone slab inflooring 18-20mm thick ofas in floor and laid over and including 15mm thick screed bed in CM 1:6 & set jointed and pointed cement mixed with pigment to match the shade of slab including rubbing and laid over and including and polishing complete all as specified and as directed. |
| 83 | M&Lfor 18-20 mm thick Black granite slab of approved quality ofany sizebeddedand jointed in greycement slurry and pointed with white cement with admixture of pigment to match the shade of granite stonelaid over and including 15 mm thick screed bed in CM (1:4) including granite polish to be done by mechanical grinder and moulding edges complete allas specified anddirected. |
| 84 | S& F in repair Rotational moulded Polyethylene water storage tank 1000 liters capacity (cylidrical vertical with closed top) of two layer hoisted and fixed in position all as specified in SSR part Icomplete all as specified and as directed. |
| 85 | Taking up or down 15mm steel tubing and connections, including cleaning for re-fixing or removal to store complete all as specified and as directed. |
| 86 | Taking up or down 20mm steel tubing and connections, including cleaning for re-fixing or removal to store complete all as specified and as directed. |
| 87 | S&F 15mm bore steel tubing medium grade ,galvanized with all fitting such as bend ,elbow, socket,tees,and fixed complete to wall or in ceiling or in floors including cutting threading and making forged bends on pipes MS hooks etc ,complete all as specified and as directed. |
| 88 | S&F 20mm bore steel tubing medium grade ,galvanized with all fitting such as bend ,elbow, socket,tees,and fixed complete to wall or in ceiling or in floors including cutting threading and making forged bends on pipes MS hooks etc ,complete all as specified and as directed. |
| 89 | S&F in repair for 15mm bore bib taps chromium platedwith crutch or butterfly handle ,screwed down , screwed for iron pipes or brass ferrulecompleteall as specified and directed. |
| 90 | S&F in repair CP pillar taps (swan neck type) cast copper alloy CP with capstan head, screwed down ,high pressure with long screwed shanks and fly nuts fixed in 15 mm bore pipes complete all as specifiedand directed.Make-Plumber/Essco of jaguar(Economical Range) |
| 91 | S&F in repair CP angle stop cock of 15mm bore screwed down for high pressure with crutch or butter fly handle ,screwed both end for iron pipes complete all as specified.Make-Plumber/Essco of jaguar(Economical Range)and directed.. |
| 92 | S&Fin repair fancy type chromium plated15mm boretwo way Bib cock cast copper alloy with crutch or butterfly handle, screwed for iron pipe or brass ferrule etc complete all as specified and as directed. Make-Plumber/Essco of jaguar(Economical Range) |
| 93 | S& F in repair CP toilet paper holder complete all as specified and as directed. |
| 94 | S&F in repair vitreous china wash down water closet pedestalpattern white excluding flushing cistern and flush pipes complete all as specified and as directed . |
| 95 | M&Lin repairs PVCvalve less,syphonic action type flushing cistern,low level ,white with inlet ball valve,float and handle including bracketsand connection to pipe and fixing of chainand pull or lever if any complete all as specified and directed. .Make-Plumber/Essco of jaguar(Economical Range) |
| 96 | S&F in repair health faucet with flexible pipe of one mtr length including wall hook forEWC complete all as specified and as directed..Make-Plumber/Essco of jaguar(Economical Range) |
| 97 | S&F in repairs vitreous china wash hand basin white including bracket,Bottele Trap, taps ,waste pipes etc complete all as specified and directed.Make:- Cera Cat No S2020177/ Jaquar KUS-WHT-35913N / Prayag as approved by GE. |
| 98 | S & F in repairs vitreous china wash basin white (oval shaped under counter) of size 550 x 400mm including 32mm brass CP waste coupling complete all as specified and as directed . |
| 99 | S & F in repairs PVC (SWR) floor trap plain or multi with stainless steel grating incl joining to waste pipe with solvent cement joint dia of outlet 75mm bore complete all as specified and as directed. |
| 100 | S&F in repair Size exc 0.13 sqmbut n.exc 0.67 sqm beveled edge mirror of selected quality glass mounted on PVC framed and fixed to wooden plug with CP screw and CP washer ccomplete all as specified and directed. |
| 101 | S&F vitreous china urinal bowl urinal flat back, size of 465x355x265mm white (min)with grating and union for discharge pipe, urinal spreader with Bottle trap/waste pipe and all fiting for urinal.complete all as specified and as directed |
| 102 | S&F in repairs PVC connection15mm size with PTMT nuts of length 450 mm long complete all as specified and as directed. |
| 103 | S&F in repairs PVC waste pipe for urinal/wash basin/ sink pipe 32mm bore 65cm long complete all as specified and as directed. |
| 104 | S&F in repairs of brass CP tubular towel rail 20 mm dia 60cm long between flange with brackets etc as in repair complete all as specified and directed. |
| 105 | S&F 0.50mm thick (including coated thickness) pre-colourpre- profiled (Galvalume/zinkalume) sheets of required colour and design having tensile strength of 550 Mpa asin roof sheeting/sunshade/ wall cladding, north light curves, fixed with zinc coated self drilling fastener including EPDM washer complete laid with one corrugation side laps and min 150mm end lap laid to slope all as per manufacturer / profile maker instruction complete all as specified and as directed. |
| 106 | M&L infor MS steel Hollow Sectionwork in tubular trussles, purlins, rafter, tubler column, where connected common rafter and running rails fixed with angle cleat or other connection plates including special shaped washer etc, complete using ERW or induction butt welded tubes conforming IS-4963,1993 andIS-1161-1979 grade ST-240 complete all as specified and as directed. |
| 107 | Preparation of newlysteel surfaces, of any description, over 10 cm width or girth, and applying two coats of synthetic enamel paint over a coat of red oxide complete complete all as specified and as directed |
| 108 | Supply only Liquid Water proofing compound PIDIPROOF LW+ of Dr FIXIT or equivalent as approved. |
| 109 | M&L for 10mm thick plaster in CM 1:3 on fair face of brick walls finished even and smooth without using extra cement with liquid water proofing compound @ 200ml per 50 Kg bag of cementcomplete all as specified(Note : Water proofing compound will be measured and paid separately) |
| 110 | M&Lsand filling under floor including waterring and consolidaion complete all as specified and directed. |
| 111 | M&Lfor 60mm thick machine pressed precast concrete interlocking paver block (glossy finish) of M-35 Gde of approved shape, size and colourconferming to IS 15658-2006 andincluding joints filled with sandcomplete all as specified and as directed. |
| 112 | S&F factory made 25 mm thick 100% solid WPC (wood polymer composite) laminated flush door shutter of required size comprising of virgin PVC resin of K value 57-60 ( suspension grade), Calcium carbonate and natural fibers ( Wood powders / rice husk/wheat husk) and non toxic additives made from extension process WPC foam sheet single extruded (Inner) with having minimum density not less than 650 kg kg/cbm, an ISO 9001-2015 certified company, having good screw holding capacity (Screw withdrawal strength of 200 N (Face) & 1100 N (Edge) minimum compissive of 50N/mm2 Modulus of elasticity 850N/mm2 and resistance of spread of flame of class A category property of being Termite/ borer free, water/ moisture proof and fire retardant WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted on both faces of shutter and fixing stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk SS screws including necessary Locking arrangement complete all as specified and as directed. |
| 113 | S&F factory made 100% solid WPC (Wood polymer composite) Door frame 105mm X 65mm (Moulded) single rebated made from wood polymer composite (single extruded process material comparison of virgin PVC polymer of k value 57-60 (Suspension grade), calcium carbonate and natural fibers (Wood powder/rice husk/wheat husk) and Non toxic additives fabricated with meter joints after applying PVC solvent cement & screwed with full body treaded star headed screws having minimum frame density of 750 kg/ cbm, an ISO 9001-2015 certified company, having good screw holding capacity (screw withdrawal strength of (Min 990 N ), minimum compressive strength of 58n/mm2, Modulus of elasticity 900N mm2 and resistance to spread of flame of class A category with property of being Termite/borer proof, water/ moisture proof and fire retardant & fixed with position with SS dash fasteners / Hold fast of required dia and length, all as per specifications drawings as directed by the Engineer-In-charge. |
| 114 | Taking down existing un-serviceable water proofing treatment from roof slab/Sloped Roof and cleaning the roof slab by wire brush and removingdebris to a distance exc 500 mtr but not exc 1.50 Km etc complete all as specified and as directed |
| 115 | M&L for 10 mm thick rendering in CM 1:3 with WPC @ 3% on fair faces of brick work or concrete surface finished even & smooth without using extra cement (Note : WPC to be paid seprately) complete all as specified and directed by Engr-in-Charge. |
| 116 | M & L forBrushing with neat cement slurry @ 3 Kg per Sqm area mixed with integral water proofing compoundas specified and directed (WPC shall be measured and paid separately under respective item). |
| 117 | Supply only Liquid Water proofing compound PIDIPROOF LW+ of Dr FIXIT or equivalent as approved. |
| 118 | M&L APP based polymeric membrane minimum weighing 3.6 kg/sqm and minimum 3mm thick reinforced with polyester non woven fabric (wt not less than 150 gms/sqm) with 15 cm longitudinal&horizontal over lapping and joints finally pasted with thermo- fused withblow lamp laid over a coat bitumen @ 1.20 Kg /Sqm over bituminousprimer 0.30 ltr per sqm as per APP manufacturerinstructionsetc complete all as specified and as directed.Note :- The Rate includes works to be carried out on sloped roof. |
| 119 | M&L two coat of aluminium paint over top surface of water proofing membraneetc complete all as specified and as directed |
| 120 | M&L for stainless steel railing chomium plated finished heavey duty inc all fixing arrangement complete and fixed in an poisition complete all as specified and directed |
| 121 | M&L for Endura tiles 8-10 thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in white or colouredcement to match over and including 15mm thick screed bed in CM 1: 6 inc dismantling of tiles complete all as specified and directed. |
| 122 | S&F 110mm bore PVC (SWR) pipe single socketed in any length with rubber ring joints laid on wall / floor complete all as specified. |
| 123 | M & L for Point wiring with FR LS PVC insulated PVC unsheathed electriccable 1100V grade single core having multi stranded copper conductor of size 1.5 Sqmm nominal cross sectional area drawn in & including non metallic rigid PVC conduit ISI marked medium grade not less than 20mm dia with all conduit accessories in concealed wiring system by cutting of wall and making good and matching disturbed surface of wall with existing surface of wall (cutting except on ceiling for fan point only, on ceiling instead of PVC conduit surface casing caping will be used) & 1.5 sqmm green FR LSPVC insulated unsheathed copper conductor as earth wire connected to earth dolly by providing lugs including galvanised boxes and bakelite sheetfor mounting switches, sockets, fan regulators etc for One light point/fan point controlled by one switch. Make of PVC conduit/Casing Caping:- Plaza/Finolex/Polycab/Kalinga/Jindal/Asian .(a) One light point controlled by one switch |
| 124 | (b) One Fan /Exhaust fan point controlled by one switch |
| 125 | (c) One 5amps socket out let point controlled by one switch on same board with other switches. |
| 126 | (d) One 5amps socket out let point on independent board controlled by one switch. |
| 127 | All as per item no-1 here in before but using PVC insulated unsheathed 2.5 sqmm cross sectional area cable for phase /neutral & for earth 2.5 Sq mm green PVC insulated cable for 15 amps socket point on independent board controlled by one switch. |
| 128 | M & L for Point wiring with FR LS PVC insulated PVC unsheathed electriccable 1100V grade single core having multi stranded copper conductor of size 1.5 Sqmm nominal cross sectional area drawn in & including non metallic rigid PVC conduit ISI marked medium grade not less than 20mm dia with all conduit accessories in PVC CONDUIT PIPE/Casing capingon iron angle of shed or on wall& 1.5 sqmm green FR LSPVC insulated unsheathed copper conductor as earth wire connected to earth dolly by providing lugs including galvanised boxes and bakelite sheetfor mounting switches, sockets, fan regulators etc for One light point/fan point controlled by one switch. Make of PVC conduit/Casing Caping:- Plaza/Finolex/Polycab/Kalinga/Jindal/Asian .(a) One light point controlled by one switch |
| 129 | S & F for Modular Switch , single pole, one way, and 5/6 Amp single module complete all as specified. |
| 130 | S & F for Modular Switch , single pole, one way, and 15/16 Amp single module complete all as specified. |
| 131 | S & F for Modular Socket outlet multipurpose having provision for 3 pin, 5/6 Amp and 2 pin, 5/6 Amp, 2 modulecomplete all as specified. |
| 132 | S & F forModularSocket outlet multipurpose having provision for 3 pin, 15/16 Amp and 3 pin, 5/6 Amp, 2 modulecomplete all as specified. |
| 133 | S&Fceiling rose surface bakelitethree terminalcomplete allas directed. |
| 134 | Supply and fix integrated LED tube light fitting 1x18/20 Watt, 6000Kcomplete fitting with all accessories duly connection with three core flexible coppercable duly fixed on two nos of PVC square boxescomplete all as specified and directed. Make:- Havells Cat No. LHEXBLP7PN1W018 , Bajaj cat Pt No. BCLSB 18WHor equivalent in Wipro |
| 135 | Supply and fixintegrated LED tube light fitting 1x9/10 Watt, 6000Kcomplete fitting with all accessoriesduly connection with three core flexible coppercable duly fixed on two nos of PVC square boxcomplete all as specified and directed.Make:- Havells Cat No. LHEXBLP7IN1W009 Bajaj Cat Pt No. BCLSB 10 WH or equivalent in Wipro |
| 136 | Supply and fix LED street light fittings1x35 Watt, 5700Kcomplete fitting having pressure dia cast aluminium housing with heat resistant toughened glass & IP 65 /66protection fixed on and including sufficient length and appropriate size GI bracket with all accessories duly connection with three core flexible coppercable complete all as specified and directed.Make:- Havells Cat No.LHEXAYP7PN6K030 Crompton Cat No. LSTO-25-CDL, Bajaj Cat No. BCLST 25W LED IV2 |
| 137 | Supply and fix LED street light fittings1x80 Watt, 5700Kcomplete fitting having pressure dia cast aluminium housing with heat resistant toughened glass & IP 65 /66protection fixed on and including sufficient length and appropriate size GI bracket with all accessories duly connection with three core flexible coppercable complete all as specified and directed.Make:- Havells Cat No.LHEXAYP7PN6K030 Crompton Cat No. LSTO-25-CDL, Bajaj Cat No. BCLST 25W LED IV2 |
| 138 | Supply and fix LED street light fittings1x120 Watt, 5700Kcomplete fitting having pressure dia cast aluminium housing with heat resistant toughened glass & IP 65 /66protection fixed on and including sufficient length and appropriate size GI bracket with all accessories duly connection with three core flexible coppercable complete all as specified and directed.Make:- BajajCat No.PRAZE F 144L WH NB-A5 TG SD Crompton Cat No. LSTO-25-CDL, Bajaj Cat No. BCLST 25W LED IV2 |
| 139 | S & F for Verticle Decorative wall mounted two way 10 watt LED light, 600Lumen, warm lightmade out of polycarbonate/metal complete all as specified and as directed. |
| 140 | Supplyand fix in replacement of LED ceiling light fittings 34/36 watt recess mounting type 2x2 luminaire, white light LED or warm light LED 5700K as per site requirment completewith driver duly connection wire etc including taking down the existing. Make BajajCat Pt No. BZRSQL36LLEDGXWH or equivalent inHavells/ Wipro/crompton. |
| 141 | Supplyand fix in replacement of LED square/round light fitting 18W recess/surface mounting type , white light LED or warm light LED 6000K as per site requirment complete with driver duly connection with coppercable etc. Make,Jaquar LAVRV018XNBajaj Cat Pt No. BGSLO SLEEK 18W WH RD, or equivalent inCrompton, Wipro Note- All Fittings Should be White/ Warm White as per site Requirement. Note :- Ceiling cutout ø 220 mm, height 23 mm ±1 mm for 18 W. |
| 142 | M&L for Sub main wiring in repairs with two runs ofsingle core FR LSH PVC insulated unsheathed cable 1100 volts grade, 6 Sqmm size with multistranded copper conductor, drawn inexistingconduit or concealed as per site requirementand all fittings like bends, tees, saddles etc including one run of FR LS PVC insulated unsheathed6.0 sqmm cable with multistranded copper conductor green PVC insulated as continuous earth conductor cable connected to earth dolly complete. Make of PVC conduit/Casing Caping:- Plaza/Finolex/Polycab/Kalinga/Jindal/Asian& Make Of wire - Make - HPL/L&T/HPL/Havells |
| 143 | Supply and fix double door SPN DBs eight wayof powder coated DB\"s suitable for MCB\"s fitted with bus bar,Neutral link,Earth bar and Din ral complete all as specified and directed by Engr-in-Charge. |
| 144 | S & F in repairs MCB SPN 40 to 100 amps 10 KA, c-series including connection with suitable size aluminium/copper lugs complete all as specified and directed by Engr-in-Charge. Make - HPL/L&T/HPL/Havells |
| 145 | S&F MCB SP 240 volts 6 to 32 Amps, 10 KA breaking capacity,\"B\" series including connection with suitable size aluminium / copper lugs complete all as specified and directed by Engr-in-Charge. |
| 146 | Supply and fixing Exhaust fan 250mm sweep, AC single phase 230 Volts, non metallic type,complete with louverincluding electric connection with suitable size copper conductor cable, clamps, nuts, bolts etc including making hole of appropriate size in the existing brick wall and making good the disturbed wall and matching with the existing surface of wall complete all as specified and directed by Engr-in-Charge. Make : Havells Model:Ventil Air-DX white or equivalent in /Bajaj/Crompton |
| 147 | Supply and fixing Exhaust fan 300mm sweep, AC single phase 230 Volts, metallic type,complete with louverincluding electric connection with suitable size copper conductor cable, clamps, nuts, bolts etc including making hole of appropriate size in the existing brick wall and making good the disturbed wall and matching with the existing surface of wall complete all as specified and directed by Engr-in-Charge. Make : Havells Model:Ventil Air-DX white or equivalent in /Bajaj/Crompton |
| 148 | Supply and fixing Exhaust fan 450mm sweep, AC single phase 230 Volts, metallic type,complete with louverincluding electric connection with suitable size copper conductor cable, clamps, nuts, bolts etc including making hole of appropriate size in the existing brick wall and making good the disturbed wall and matching with the existing surface of wall complete all as specified and directed by Engr-in-Charge. Make : Havells Model:Ventil Air-DX white or equivalent in /Bajaj/Crompton |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
| 4 | Click here to download tender document | Tender Documents |
| 5 | Click here to download tender document | Tender Documents |
| 6 | Click here to download tender document | Tender Documents |
| 7 | Click here to download tender document | Tender Documents |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2026 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
