|
| 1 | B & R Division Items |
| 2 | Demolition of un-reinforced cement concrete in ground floor and paving not exceeding 15 cm thick (below or above ground level) complete all as specified and directed. |
| 3 | Demolition of brick work or stone/ boulder masonry, built in cement mortar including all quoins, pillars etc. complete all as specified and as directed. |
| 4 | Dismantling plain or corrugated steel sheeting, any gauge or any thickness as in roof covering, wall cladding, etc.including all necessary staging / scaffolding, etc. as required complete all as specified and as directed. |
| 5 | Dismantling of timber scantling 40 Sqcm and over in section, in any position in unframed work complete all as specified and directed. |
| 6 | Dismantling wall and ceilingboards (fibre, pulb, insulation etc) or insulation boards slabs/blankets any thickness including cover fillets all as specified and as directed. |
| 7 | Taking down chowkhats or frame with shutters (without taking off shutters from frame) each not exceeding 1.50 Sqm each complete all as specified. |
| 8 | Taking down Chowkats or frames with shutters exceeding 1.5 Sqm but not exceeding 4 Sqm each (without taking off shutters from the frame) complete all as specified. |
| 9 | Taking down wooden shutturs of any description sizeexceeding 1.0 Sqm but not exceeding 2.0 Sqm each from steel / wooden frame and refixing after easing and adjusting and refixing builders hardware in the same opening complete all as specified. |
| 10 | Surface dressing n exc 15 cm deep and gettingout in soft / lose soil complete all as specified |
| 11 | Excavating over area, n exc 1.50 m deep for foundation and getting out hard / densetype of soil complete all as specified and directed. |
| 12 | Excavating in trenches, n exc 1.50 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out soft/ loosetype of soil complete all as specified and directed. |
| 13 | Returning, filling in trenches including spreading, leveling watering and ramming in layers not exceeding 25cm all as specified. |
| 14 | Removing of surplus soil not exceeding 50 m and deposited where directed at a level not exceeding 1.50m above the starting point all as specified. |
| 15 | Excavating in post holes each n exc 0.5 cum, getting out, in soft /loose soil, ramming earth filling or borken rubble mixed with earth around in layers nexc 25 cm watering and removing ssurfaces soil to distance nexc 50 m and making good surfaces all as specified and directed. |
| 16 | M&L for earth filling under floor incl spreading ,levelling & well ramming includuing watering as required n exc . 25 cm thick . (Note :- Earthobtained from relevant excavated items mention above is reused ) |
| 17 | M&L for Hardcore broken stone of gauge n exc 63mm deposited spread and levelled in layers n exc 15cm thick watered and rammed to a true surface complete all as specified and directed. |
| 18 | M&L for PCC (1:4:8), Type D2 using 40 mm graded stoneaggregate as in foundations, sub-base,filling and mass concrete complete all as specified. |
| 19 | M&Lfor providing 100 mm thick plain cement concrete (1:4:8) type D-2 using (40mm gradedstone aggregate) as in Sub base of floor rough surface complete all as specified. |
| 20 | M&Lfor providing plain cement concrete (1:3:6) type C-2 using (40mm gradedstone aggregate) as in foundations, sub-base,filling and mass concrete complete all as specified. |
| 21 | M & Lfor 75mm thickcement concrete 1:3:6 type C2 (using 40mm graded stone aggregate) as in plinth protection finished even and fair without using extra cement laid inpanels and joints filled with bituminous mastic filling with 1 part of bitumen and 3 part of sand complete all as specified and directed. |
| 22 | M & L for plain cement concrete (1:2:4) type B1 using 20mm graded aggreagate as in bed blocks, coping , cills, steps, kneelers, bed plates, apex stones kerbs and similar works including necessary formwork complete all as specified and directed. |
| 23 | M & L for plain cement concrete (1:2:4) type B1 using 20mm graded aggreagate as in levelling course and similar works including necessary formwork complete all as specified and directed. |
| 24 | Material and labour for 50 mm thick Plain Cement concrete type B-0 1:2:4 (12.50mm graded crushed stone aggregates) for sub base in floor fair and rough for receiving tiles, as topping layer all as specified and directed. |
| 25 | Material and labour for 25 mm thick Plain Cement concrete type B0 1:2:4 (12.50mm graded crushed stone aggregates) for sub base in floor complete all as specified and directed. |
| 26 | M & L for Precast reinforcement cement concrete (1:2:4) type B1 using 20mm graded aggreagate as in cover slab for man holes, chullah hoods, chajja, water troughts, mangers, shelves and similar article with plain faces set in cement mortar (1:4) incl necessary formwork complete all as specified and directed. |
| 27 | Material and labour for precast autoclaved acrated concrete bricks (AAC) block masonary with 150mm thick with grade -I, AAC block of density 551 to 650kg/cum conformimg to IS-2185 (Part -III) i super structure above plinth level upto floor V level with RCC bend at sill level and lintel level with approved block laying polymer modified adhesive mortar complete all as spd and directed. Note : RCC bend and reinforcement shall be measured and paid separately |
| 28 | M & L for forming contraction (Dummy) joints 65mm deep X 10mm wide filled with sealing compound of grade \"A\" a complete all as specified and as directed. |
| 29 | Use and waste formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter rough finished flat surfaces of concrete complete all as specified and as directed. |
| 30 | Use and waste formwork to sides and soffits of floor or roof beam, beam hunching, girder, lintels, cantilever, shelves including supports etc for rough finished flat surfaces of concrete complete all as specified and directed |
| 31 | Use and waste of formwork to soffits of rough finished flat suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed |
| 32 | Use and waste of formwork to sides of pillars, posts, struts, piers, columns and stanchions for rough finished flat surfaces of concreteall as specified and directed. |
| 33 | Material and labour formwork to,rough finished surfaces of flat concrete, chullah hoods, chajjas,troughs and similar items including edges,etc complete all as spd and directed. |
| 34 | Material and labour for providing Reinforced Cement Concrete (Nominal mix) (1:1.5:3) type A1 using 20 mm graded aggregate as in foundation including rafts, footings,foundationbeams, plinth beams, bases of columns etc all as specified and directed. |
| 35 | Material and labour for providing Reinforced Cement Concrete (Nominal Mix) 1:1.5:3 type A1using 20 mm graded aggregate as in columns, pillars, piers, posts and struts complete all as specified and directed. |
| 36 | Material and labour for providing Reinforced Cement Concrete (Nominal Mix) 1:1.5:3 type A1 using 20 mm graded aggregate as in beams, cantilever, lintels over 1.5 m complete all as specified and directed. |
| 37 | Material and labour for providing Reinforced Cement Concrete(Nominal Mix) (1:1.5:3) type A1 using 20 mm graded aggregate as inChajjas etc allas specifiedand directed. |
| 38 | Material and labour for providing Reinforced Cement Concrete(Nominal Mix) 1:1.5:3 type A1using 20mm aggregate as in slab supported on walls , beams, and column in floors, roof, landing, balconies, canopies, deck slab and in shelves and like etc comlpete all as specified and directed. |
| 39 | Material and labour for Reinforced Cement Concrete M-25 (design mix) using 20 mm graded aggregate as in foundation including rafts, footings, foundation beams, plinth beams, bases for columns etc complete all as specified and directed. |
| 40 | Material and labour for Reinforced Cement Concrete M-25 (design mix) using 20 mm graded aggregate as inbeams, cantilever, lintels over 1.5m complete all as specified and directed. |
| 41 | Material and labour for Reinforced Cement Concrete M-25 (design mix) using 20 mm graded aggregate as incolumn, pillars, piers, posts, and struts complete all as specified and directed. |
| 42 | M & Lfor 10mm dia and over TMT bars, cut to length bend to shape as required including cranking, hooking etc and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed. |
| 43 | M & Lfor 6mm to 8mm dia and over TMT bars, cut to length bend to shape as required including cranking, hooking etc and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed. |
| 44 | M & Lfor Mild Steel TMT Bar 6mm dia and over up to 10 mm dia as in stirrups, spacers and binders as required including cranking, hooking etc and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed |
| 45 | M & L for brickwork with subclass \"B\" or locally available best qualityold size bricks, straight or curved on plan exc 6 m mean raduis,built in CM (1:6) complete all as specified and directed. |
| 46 | M & L for half brick work in cement mortar (1:4) straight or curved on plan to any radius with locally available Subclass ‘B’ old size best quality bricks all as specified . |
| 47 | M & Lrendering 10mm thick cement plaster on other than fair faces of brick wall or condrete surfaces in CM (1:6) finished fair and even complete all as specified. |
| 48 | Material and labour for 12 mm thick renderingin cement mortar 1:6 on fair faces of brick wall or concrete surfaces, finished the surfaces even and fair complete all as specified. |
| 49 | M & Lfor 15 mm thick renderingin cement mortar 1:4 on fair faces of brick wall or concrete surfaces, finished the surfaces even and fair without using extra cement complete all as specified. |
| 50 | M & Lrendering 15 mm thick cement plaster in two layer each of 10+5 mm thick on fair faces of brick wall or condrete surfaces in CM (1:4) & water proofing compound mixed with second layer @ 3% finished fair and even complete all as specified. (Note :WPC measured separately). |
| 51 | M & L rendering 20mm thick coloured cement mortar 1:2 on concrete floor finish including polishing complete all as specified. |
| 52 | Supply only integral water proofing compound WPC complete all as specified. |
| 53 | M & L Non Skid ceramic paver tiles colour 7 to 8mm thick (square/ rectangular) area of each tile exceeding 0.06 but not exceeding 0.11 sqm, as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile including 20 mm thick screed bed or bedding layers in cement mortar 1:6 over brushing with neat cement slurry as specified |
| 54 | M & L Non Skid ceramic tiles, joint free, colour 7 to 8mm thick (square/ rectangular) area of each tile exceeding 0.18 but not exceeding 0.38 sqm, as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile including 15 mm thick screed bed or bedding layers in cement mortar 1:6 over brushing with neat cement slurry as specified |
| 55 | M & LGlazed ceramic coloured tilesin vertical surface size 450mm x 350mm x & ( 6mm to 7mm )mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over & including10mm thick screed bed or backing coat in cement mortar 1:4layingof skirting/dado on walls all as specified and directed. |
| 56 | M&L Machine cut kota stone20-25mm thick as in slab flooring, over incl cement mortar screed bed laid 20mm thickin cm 1 : 3 with cement slurry @ 4 kg/sqm jointed and pointed with grey cement slurry mixed with pigment to match the shade of slab including cutting and polishing to achieve mirror/granite finish complete all as specified and as directed. |
| 57 | M&L Machine cut kota stone 20mm thick as in skirting or dado over incl cement plaster backing coat 10mm thickin cm 1 : 3 with cement slurry @ 4 kg/sqm jointed and pointed with grey cement slurry mixed with pigment to match the shade of slab including cutting and polishing to achieve mirror/granite finish complete all as specified and as directed. |
| 58 | M&L in repairs for 18-20mm thick granite stone slab, of any type, table rubbed and polished, in steps, jambs, pillars, window cills, cooking platforms and the like in laid over and including 15mm thick screed in cement mortar (1:4) (rate shall be included) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of slab and taking off old damaged slab and disposing off complete all as specified and as directed. |
| 59 | Supply and fix pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified. |
| 60 | Supply and fix pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified. |
| 61 | Supply and fix Framed work such as grills, gratings, etc.. with ends of bars or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed. |
| 62 | S&F Roof trusses (framed), trussed,purlins, crane gantries, rails ,posts and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats nuts bolts plates (plain or chequered) etc. |
| 63 | Supply and fix Steel work in trusses, purlins, posts and the like using tubular/ square hollow sections including special shaped washer etc. complete using ERW or induction butt welded tubes/SHS conforming to IS.1161 - 2014 / IS.4923 - 1997 grade St.-240 complete all as specified and directed. |
| 64 | Supply and fix 5 mm thick mild steel Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment conforming to Fe 290 grade E-165 complete all as specified. |
| 65 | Supply and fix mild steel screw bolts (machine made) of 11 mm to 15 mm dia with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut,length of bolt exceeding 10 cm but not exceeding 15 cm complete all as specified. |
| 66 | S & F bands, straps,clamps,cleats & small articles, supports or stays for rainwater,ventilating pipes, including bolts etc conforming to Fe-290 Gde-E-165 all as specified and directed. |
| 67 | S & F Pressed steel frames made of 1.25mm thick MS sheet of profile 165x60mm for door and window frames with one or more rebates includinghinges, lock strike plate, shock absorber, treating of internal surfaces of chowkhats with coal tar or black paint including hinges, hold fasts/lugs etc complete all as specified. |
| 68 | S&F Steel ventilator with top hung shutter including hinges, steel peg stay, lugs as in hold fast with locking arrangements, complete all as specified. |
| 69 | S & F 30 mm thick Second class Hardwood Plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats, complete all as specified. |
| 70 | S&F 2nd class hard woodglazed andskeleton door shutters 35 mm thick open rebated and prepared to receive glass, guage etc (withoput sash bars), edge of framing plain chemfered ro rounded fitted with cut and mitred beds for securing glass etc size of members of shutter as specified in SSR Part I section 8 clause 8.20(a) complete all as specified and directed. |
| 71 | S&F for 2nd class hardwood, 30mm thick, glazed and skeleton shutters, open rebated and prepared to received glass, guaze etc (with sash bars) edge of framing plain, chamfered or rounded fitted with cut and mitered beads for securing glass etc. |
| 72 | S & F Solid PVC door frame of size 50 mm x 47 mm made of 5 mm plain colour PVC sheet reinforced with mild steel square tube complete all as specified in clause 8B.3.1 and shown on page 150 of MES Schedule Part-II (2010). |
| 73 | S & F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and wood grain printed PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of wood grain printed sheet, 15mm wide x mm thick PVC sheet beading used inside stiles and rail and decorative PVC beading of 10mm x 10mm (90 degree), used solvent cement, supply and fixing in the frame at site as per clause 8 B.2.1 of MES schedule Part-II (2004) complete all as specified. Make: Rajshri or equivalent as approved. |
| 74 | S&F Steel ventilator with top hung shutter including hinges, steel peg stay, lugs as in hold fast with locking arrangements, complete all as specified. |
| 75 | S&F 3.00 mm thick sheet glass ordinary quality and glazing with oil putting square nexc 0.5 sqm in each pane complete all as specified. |
| 76 | S&F 75mm MS Butt hinges, medium weight, cold rolledcomplete all as specified. |
| 77 | Supply and fix 300mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixedcomplete all as specified. |
| 78 | Supply and fix 150 mm long aluminium handles cast type anodised extruded section complete all as specified & directed . |
| 79 | Supply and fix 200 mm long aluminum anodised barrel tower bolts of extruded section complete all as specified and directed. |
| 80 | Supply and fix 150 mm long aluminum anodised barrel tower bolts of extruded section complete all as specified and directed. |
| 81 | Supply and fix vitreous china Squatting pan, \"Orissa\" pattern, Size 580 X 440mm ,with integral foot rests (excluding flushing ciestern and flush pipe) incl necessary lime concrete and 100 mm bore cast iron \"P\" trap with 550 to 600mm long neck for connecting WC to branch piece with cement joints complete all as specified & as directed . |
| 82 | Supply and fix vitreous china wash basin, white, wall hung basin full pedestal with fixing accessories , size 560 X 430 X 195 mmincluding waste coupling and excluding taps, waste ,chain and plug and porcelain stoppercomplete all as specified. Make:Jaquar Catalouge No- CNS-WHT-811 and Equivalent as per approved list of make) |
| 83 | S & F PVC valveless,syphonic action type,low level flushing cistren 10 ltr capacity ISI Marked incl all acessories and 32mm dia PVC flush / discharge pipe incl float valve, inlet complete all as specified. |
| 84 | S&F of sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed. |
| 85 | S & Fvitreous china soap dish chromium plated approx. size 160mm x 160mm x 90mm fixed to plug complete all as specified. |
| 86 | S & F PVC connections 15 mm size with PTMT nuts of length 450 m complete all as specified. |
| 87 | M&L for water connection pipe for hot and cold water application, steel armoured of length not less than 600mm suitable with brass union on both sides to fixed 15mm bore GI pipe for geyser functioning complete all as specified and directed. |
| 88 | S & F 15mm bore pillar tap cast copper alloy with capstan head, fancy type, chromium plated concealed screwed down high pressure with or without hot or cold with long shunk screwed shanks and fly nuts screwed for iron pipes and connecting to water pipe line complete all specified and directed. |
| 89 | Supply and fix as 15 mm bore bib taps fancy type, chromium plated, castcopper alloy with crutch or butter fly handle, screwed down, screwed for iron pipe or for brass ferrule all as specified. |
| 90 | Supply and fix 15mm bore stop valve/angle valve, cast copper alloy cromium plated fancy type screwed down high pressure, with crutch or butterfly handle for 15 mm bore pipe or for unions all as specified. |
| 91 | Supply and fix 125mm dia CP brass shower rose with or without swivel joints, any colour including shower arm 15mm dia, 195mm long with bend of 45 degree with flange of CP brass complete all as specified.Make : Parryware cat No. T9809A1 or equivalent as per approved list of make. |
| 92 | Supply and fix Towel rail, 20mm dia brass chromium plated, 600mm long with fancy type brass chromium plated brackets on both sides and fixed with steel screws and wooden/rawl plugs as in repair complete all as specified. |
| 93 | S&F 600mmx450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed. |
| 94 | Supply and fix stainless steel sink with drainage board1.00mm thick for kitchen or laboratory, with plug, waste pipe, washers, including bedding 20mm thick in cement mortar (1:4), cantilever cast iron brackets, connecting union etc. overall size 915mm x 460 mm with bowl size 410mm x 330mm x 160mm etc complete all as specified and as directed. |
| 95 | Supply and fix brass CP mixer for mixing hot and cold water screwed down for iron pipe and fixed for 15mm bore pipe complete all as specified and as directed. |
| 96 | Supply and fix 50mm bore low density polyethylene pipes (LDPE) of pressure rating 6kgf/qcm to wall ceiling or in floors etc complete all as specified and as directed. |
| 97 | Supply and fix 32mm bore low density polyethylene pipes (LDPE) of pressure rating 6kgf/qcm to wall ceiling or in floors etc complete all as specified and as directed. |
| 98 | Supply and fix eaves gutters 110 mm borePVC (SWR) Pipe single socketed in any length with rubber ring joints, fixed in wall complete all as specified. |
| 99 | Supply and fix 110mm diaPVC (SWR) pipes single socketed, in any length, laid in trenches or in floors / fixed to walls complete all as specified. |
| 100 | Supply and fix 75mm diaPVC (SWR) pipes single socketed, in any length, laid in trenches or in floors / fixed to walls complete all as specified. |
| 101 | Supply and fix 110mm dia PVC (SWR) bend suitable for pipe complete all as specified. |
| 102 | Supply & Fixed 110mm dia PVC (SWR) reducer suitable for pipe complete all as specified. |
| 103 | Supply & Fixed 75mm dia PVC (SWR) vent cowl suitable for pipe complete all as specified. |
| 104 | Supply & Fixed 110mm dia PVC (SWR) WC connector with lip ring suitable for pipe complete all as specified. |
| 105 | Supply & Fixed 110mm dia PVC (SWR) \"S\" trap suitable for pipe complete all as specified. |
| 106 | M & L75mm dia PVC(SWR) floor trap, outlet, plain with grating including jointing with solvent cement complete all as specified. |
| 107 | Supply and fix 110mm bore PVC (SWR) junction, single T equal or unequal with or without door access complete all as specified. |
| 108 | S&F 15mm bore steel water tubing, medium grade, galvanised with screwed and socketed joints, in any length, including supply and fixing all fittings, ISI marked conforming to IS -1239 and fixed to walls or laid in floors / trenches required for water connections complete all as specified and as directed. |
| 109 | S&F 20mm bore steel water tubing, medium grade, galvanised with screwed and socketed joints, in any length, including supply and fixing all fittings, ISI marked conforming to IS -1239 and fixed to walls or laid in floors / trenches required for water connections complete all as specified and as directed. |
| 110 | S&F gun metal gate valve 20mm dia, cast copper alloy, screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe complete all as specified and directed. |
| 111 | Material and labour for pre-painted designer false ceiling using E-grid 2430, 180 GSM (exposed ceiling suspension system ) of grid size 600 mm x 600 mm with main runner 38 mm x 24 mm and wall angle 24 mm x 24 mm using 4 mm thick High Pressure Non Asbestos Fibre Cement prepainted decorative board (E-Board Classic)in a grid of GI system duly suspended with 4 mmdia GI bar hanger fixed with steel dash fasteners or iron purlin from the roof with adjustment clip providing positions for light fixtures, air conditioning diffuser and ducts ,sprinkler ,smoke detectors etc. The main runners to be secured to structural soffits by hanger @ 1220 mm maximum c/c. the last hanger at the end of each main runner should not be placed at more than 450 mm from the adjacent wall, Flush fitting 1220 mm cross tee to be interlocked between main runners @ 610 mm c/c,so as to form 600 mm x 600 mm grid and painted with two coats of acrylic emulsion paint of approved shed /make over a coat of cement primer before installing it on the grid complete all as specified. Make: Everest Industries Ltd or equivalent as per IS 14862. |
| 112 | M & Lfor preparation of new or previously untreated wall surfaces and applying three coats of white wash complete all as specified and directed. |
| 113 | Material and labour for applying two coats of cement base paint over one coat of primer on plastered surfaces of walls including preparation of new or previously untreated surfaces all as specified and directed |
| 114 | Material and labour for preparation of new wall surfacesand applying two coats of oil bound distemper (white or tinted) over a coat of 1 mm thick wall putty over a coat of alkali resistance primer complete all as specified. |
| 115 | M & Lpreparation of new steel surfaces of any description over 10cm width or girth not otherwise described and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and as directed. |
| 116 | M & Lfor preparation of new wooden surfaces of any description not other wise described over 10 cm width or girth and applying two coat of Synthetic enamel paint over a coat of pink primer complete all as specified and as directed. |
| 117 | E & M Division items |
| 118 | Taking down carefully copper/aluminium point wiring (light, fan, buzzer, socket or power) complete including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc includingremoving from site for taking credit and making good to disturbed surface of walls, floors etc as per existing specification complete all as specified and as directed. |
| 119 | M&L for point wiring with FRLSH stranded copper conductor1.5 sqmm (nominal area), two single core, PVC insulated cable 1100 volts grade, ISI-694 markedin and including heavy duty, PVC Conduit concealed of suitable size including all accessories etc ISI marked, with GI sheet pressed terminal box (recessed) with 3mm thick laminated hylem sheet top cover suitable for fixing switches, sockets and regulators including PVC insulated FRLSH stranded copper conductor 1.5 sqmm (nominal area) single core cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed for One light point controlled by one switch. |
| 120 | M&L for point wiring with FRLSH stranded copper conductor1.5 sqmm (nominal area), two single core, PVC insulated cable 1100 volts grade, ISI-694 markedin and including heavy duty, PVC Conduit concealed of suitable size including all accessories etc ISI marked, with GI sheet pressed terminal box (recessed) with 3mm thick laminated hylem sheet top cover for fixing switches, sockets and regulators including PVC insulated FRLSH stranded copper conductor 1.5 sqmm (nominal area) single core cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed for One ceiling fan point controlled by one, one way switch 5 Amp. |
| 121 | M&L for point wiring with FRLSH stranded copper conductor1.5 sqmm (nominal area), two single core, PVC insulated cable 1100 volts grade, ISI-694 markedin and including heavy duty, PVC Conduit concealed of suitable size including all accessories etc ISI marked, with GI sheet pressed terminal box (recessed) with 3mm thick laminated hylem sheet top cover for fixing switches, sockets and regulators including PVC insulated FRLSH stranded copper conductor 1.5 sqmm (nominal area) single core cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed for One exhaust fan point controlled by one, one way switch 5 Amp. |
| 122 | M&L for point wiring with FRLSH stranded copper conductor1.5 sqmm (nominal area), two single core, PVC insulated cable 1100 volts grade, ISI-694 markedin and including heavy duty, PVC Conduit concealed of suitable size including all accessories etc ISI marked, with GI sheet pressed terminal box (recessed) with 3mm thick laminated hylem sheet top cover for fixing switches, sockets and regulators including PVC insulated FRLSH stranded copper conductor 1.5 sqmm (nominal area) single core cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed forOne 3 pin 5 Amp socket outlet point controlled by one switch on independent board. |
| 123 | M&L for point wiring with FRLSH stranded copper conductor1.5 sqmm (nominal area), two single core, PVC insulated cable 1100 volts grade, ISI-694 markedin and including heavy duty, PVC Conduit concealed type of suitable size including all accessories etc ISI marked, with GI sheet pressed terminal box (recessed) with 3mm thick laminated hylem sheet top cover for fixing switches, sockets and regulators including PVC insulated FRLSH stranded copper conductor 1.5 sqmm (nominal area) single core cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed for One 3 pin 5 Amp socket outlet point controlled by one switch on the same board. |
| 124 | M&L for point wiring with FRLSH stranded copper conductor2.5 sqmm (nominal area), two single core, PVC insulated cable 1100 volts grade, ISI-694 markedin and including heavy duty, PVC Conduit concealed type of suitable size including all accessories etc ISI marked, with GI sheet pressed terminal box (recessed) with 3mm thick laminated hylem sheet top cover for fixing switches, sockets and regulators including PVC insulated FRLSH stranded copper conductor 2.5 sqmm (nominal area) single core cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed for one power point 3/5 pin socket outlet 15 Amps on the independent board. Note: The point wiring will be done from DBs to the switch sockets of any size with three wires running independently for each point and with no tappings. |
| 125 | M&L for point wiring with FRLSH stranded copper conductor4.0 sqmm (nominal area), two single core, PVC insulated cable 1100 volts grade, ISI-694 markedin and including heavy duty, PVC Conduit concealed type of suitable size including all accessories etc ISI marked, with GI sheet pressed terminal box (recessed) with 3mm thick laminated hylem sheet top cover for fixing switches, sockets and regulators including PVC insulated FRLSH stranded copper conductor 4.0 sqmm (nominal area) single core cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed for one power point on independent board of AC/equipments etc controlled by one SP/SPN MCB. Note: The point wiring will be done from DBs to the switch sockets of any size with three wires running independently for each point and with no tappings. |
| 126 | M & Lfor point wiring with FRLSH stranded copper conductor1.5 sqmm (nominal area), two single core, PVC insulated cable 1100 volts grade, ISI-694 markedin and including heavy duty, PVC Casing caping including all accessories etc ISI marked, with GI sunken box suitable for fixing switches, sockets and regulators including PVC insulated FRLSH stranded copper conductor 1.5 sqmm (nominal area) single core cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed for One light point controlled by one switch. |
| 127 | M & Lfor point wiring with FRLSH stranded copper conductor1.5 sqmm (nominal area), two single core, PVC insulated cable 1100 volts grade, ISI-694 markedin and including heavy duty, PVC Casing caping including all accessories etc ISI marked, with GI sunken box suitable for fixing switches, sockets and regulators including PVC insulated FRLSH stranded copper conductor 1.5 sqmm (nominal area) single core cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed forOne 3 pin 5 Amp socket outlet point controlled by one switch on independent board. |
| 128 | M & Lfor point wiring with FRLSH stranded copper conductor2.5 sqmm (nominal area), two single core, PVC insulated cable 1100 volts grade, ISI-694 markedin and including heavy duty, PVC Casing caping including all accessories etc ISI marked, with GI sunken box suitable for fixing switches, sockets and regulators including PVC insulated FRLSH stranded copper conductor 2.5 sqmm (nominal area) single core cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed for 3 pin, 15 Amp socket outlet, on the independent board |
| 129 | S&Fmodular switch 1 way 6A/10A, 1 Module complete all as specified and directed. |
| 130 | S&Fmodular switch 1 way 16A/20A, 1 Module complete all as specified and directed. |
| 131 | S&Fmodular socket 6A/10A, 2/3 pin combined 2 module complete all as specified and directed. |
| 132 | S&Fmodular socket 16A/20A, 2/3 pin combined 2 module complete all as specified and directed. |
| 133 | S&F ceiling rose surface bakelite with three terminals all as specified and directed |
| 134 | S&F electronic fan regulator modular type stepped type (5 steps) 120W, 230V, 2 module, ISI marked duly connected up complete all as specified and directed |
| 135 | S&F modular metal flush box 3 module with white cover plate with frame ISI marked complete all as specified and directed |
| 136 | S&F modular metal flush box 6 module with white cover plate with frame ISI marked complete all as specified and directed |
| 137 | M&L for submain wiring with two single core 10.0 sqmm PVC insulated unsheathed cable multi-strand copper conductor FRLSH drawn through and including PVC non metallic rigid Conduit concealed with all fittings and fixing accessories on roof, walls, ceiling etc including 1 x 6.0 sqmm PVC insulated FRLSH unsheathed multi strand copper conductor earth wire connecting earth including cutting groove for concealed wiring, making good to disturb surface of wall/floor with cement mortar and finishes to match existing incl taking out old existing submain wiring complete all as specified and directed. Note: Two run of single core cable, one run earth wire and one run PVC Conduit will be measured as one length. |
| 138 | M&L for submain wiring with two single core 4.0 sqmm PVC insulated unsheathed cable multi-strand copper conductor FRLSH drawn through and including PVC non metallic rigid Conduit concealed with all fittings and fixing accessories on roof, walls, ceiling etc including 1 x 2.5 sqmm PVC insulated FRLSH unsheathed multi strand copper conductor earth wire connecting earth including cutting groove for concealed wiring, making good to disturb surface of wall/floor with cement mortar and finishes to match existing surface complete all as specified and directed. Note: Two run of single core cable, one run earth wire and one run PVC Conduit will be measured as one length. |
| 139 | M & Lfor submain wiring with two single core 10.0 sqmm PVC insulated FRLSH unsheathed cable multi-strand copper conductor drawn through and including PVC casing caping with all fittings and fixing accessories on roof, walls, ceiling etc including 1 x 6.0 sqmm PVC insulated FRLSH unsheathed multi strand copper conductor earth wire connecting earth including cutting groove for concealed wiring, making good to disturb surface of wall/floor with cement mortar and finishes to match existing complete all as specified and directed. Note: Two run of single core cable, one run earth wire and one run PVC Conduit will be measured as one length. |
| 140 | Supply & Fix LED betten plastic type fitting of capacity 20W, operating on 230V, 50Hz, AC Supply having luminous efficacy of not less than 125 lumens/watts, CCT 6500K, P.F>0.9, 2.5 KV surge protection, 4-feet long, housing made out of extruded alluminium with decorative end caps elegently designed complete all as specified. |
| 141 | Supply & Fix enviromental friendly bldg security street light, LED luminaire 25 watt made up of pressure die cast alluminium body with mid power LED as lighting sources and PC cover having Top opening separate driver compartment with IP66 protection and impact resistance of IK07 including fixing arrangements and taking down old rusted bracket fittings completeall as per directed by Engr-in–charge. |
| 142 | S&F plastic body exhaust fan 250 mm sweep complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, copper winding and connecting to ceiling rose with flexible copper cable including making holes on the wall and making good to the disturbed surfaces complete all as specified and as directed. |
| 143 | S&F BLDC ceiling fan 1200mm sweep complete with blades, down rods and accessories, 230 V, min air delivery 210 CFM with service value 6.00 BEE 5 star rated & provn of ‘S’ type fan hook complete all as specified and directed. |
| 144 | Supply and fix electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection pipe etc complete all as specified and as directed. |
| 145 | S&F sheet metal enclosure powder coated three phase and neutral DB for fixing of MCBs, 4 way double door with bus bar includinggrouting on the wall by means of screws and rawal plugs and making good disturbed surfaces complete all as specified and directed. |
| 146 | S&F sheet metal enclosure powder coated single phase DB for fixing of MCBs, 4 way double door with bus bar includinggrouting on the wall by means of screws and rawal plugs and making good disturbed surfaces complete all as specified and directed. |
| 147 | S&F sheet metal enclosure powder coated single phase DB for fixing of MCBs, 8 way double door with bus bar includinggrouting on the wall by means of screws and rawal plugs and making good disturbed surfaces complete all as specified and directed. |
| 148 | S&F MCB TPN of capacity 63 Amps ,240 V, 10 KA \"C\" curve complete all as specified and directed. |
| 149 | S&F MCB SPN of capacity 32 Amps,240 V, 10 KA \"C\" curve complete all as specified and directed. |
| 150 | S&F MCB SP of capacity 5-32 Amps,240 V, 10 KA \"C\" curve complete all as specified and directed. |
| 151 | S&F MCB SP of capacity 5-32 Amps,240 V, 10 KA \"B\" curve complete all as specified and directed. |
| 152 | Taking out old existing earthing and M & Lfor new earthing with galvanised steel earth plate electrode 600mmX600mmX6mm thick burried directly in ground (earth pit not less than 2.25 mtr below ground level) with top edge of the plate not less than 1.5 mtr below ground level connected to 4mm dia GI wire protected by 20 mm bore light grade galvanised iron pipe and other end connected to test point as directed including funnel with wire mesh and watering pipe 20 mm bore medium grade galvanised iron pipe with charcoal and common salt in alternaterlayers of 15 cm thickness all around the GI plate electrode with concrete pit in PCC 1:3:6 type C-1 with cast iron frame including cast iron cover 10mm thick hinged to CI frame and 6mm MS rod for handle, necessary excavation and earth wok in hard/dense soil and disposal of spoil to a distance n exc 50 m and necessary testing complete all as shown in electrical plate No 3 of SSR part-I complete all as specified and directed. |
| 153 | M & Lfor new earthing with galvanised steel earth plate electrode 600mmX600mmX6mm thick burried directly in ground (earth pit not less than 2.25 mtr below ground level) with top edge of the plate not less than 1.5 mtr below ground level connected to 4mm dia GI wire protected by 20 mm bore light grade galvanised iron pipe and other end connected to test point as directed including funnel with wire mesh and watering pipe 20 mm bore medium grade galvanised iron pipe with charcoal and common salt in alternaterlayers of 15 cm thickness all around the GI plate electrode with concrete pit in PCC 1:3:6 type C-1 with cast iron frame including cast iron cover 10mm thick hinged to CI frame and 6mm MS rod for handle, necessary excavation and earth wok in hard/dense soil and disposal of spoil to a distance n exc 50 m and necessary testing complete all as shown in electrical plate No 3 of SSR part-I complete all as specified and directed. |
| 154 | Supply, fixing, commissioning & testing of XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, Electric power cable (heavy duty) with aluminium conductors, 1100 volts, grade cross sectional area 10 sqmm 2.0 core laid in trenches/fixed to wall/under road/pipe etc with copper cable glands & copper thimbles complete all as specified and directed. |
| 155 | Supply, fixing, commissioning & testing of PVC flexible copper cable 2.5 sqmm from cable junction box to street light fittigs, security light fittings, flood light fittings, lamp posts etc complete all as specified and directed. |
| 156 | Material & labour GI tube light grade 25 mm bore for protection of cable complete all as specified and directed. |
| 157 | M & Lfor steel water tubing 15mm dia, medium grade galvanised with new fitting laid in trenches or on wall complete all as specified and directed. |
| 158 | S&F 15mm bore bib taps , quarter turn with flange type, cast copper alloy, chromium plated with crutch or butter fly handle, screwed down for iron pipe or for brass ferrule including accessories complete all as specified and directed. |
| 159 | M&L for water connection pipe for hot and cold water application, steel armoured of length not less than 600mm suitable with brass union on both sides to fixed 15mm bore GI pipe complete all as specified and directed. |
