|
| 1 | Demolition of cement concrete (un reinforced) in ground floors and paving n. exc. 15cm thickness (below or above ground level) removing rubbish off the premises etc outside Ministry of Defence land complete all as specified and directed. |
| 2 | M&L for 25 mm thick PCC (1:2:4)type B0 using 12.5 mm graded stone aggt as in floors finished even and fair with using extra cement, complete all as specified and directed. |
| 3 | Taking down chowkhats or frame with shutters (without taking off shutters from the frame) not exceeding 1.50 Sqm each complete all as directed. |
| 4 | Taking down chowkhats or framewith shutters (without taking off shutters from frames) exceeding 1.5 Sqmbut not exceeding 4 Sqm each complete all as directed. |
| 5 | S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm single side prelam PVC sheet & edges will be painted to match with prelam sheet, reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing, complete all as specified and directed. |
| 6 | S&F Factory Made Solid PVC Moulded Door Shutter with partcle board core, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on the front face & 2mm Plain colour PVC Sheet on back face, supplying & fixing in frame at site as per specification & drawing complete all as specified and directed. |
| 7 | S&F Mild steel butt hinges, Medium grade, 100 mm size , complete all as specified and directed. |
| 8 | S&F extruded aluminium alloy handles, fabricated type, anodized, 150 mm size , complete all as specified and directed. |
| 9 | S&F for 150 mm long, aluminium, barrel tower bolts of extruded section of aluminium alloy, anodised finish not be less than Grade AC 10 of IS 1868:1996 with transparent anodic filmcomplete all as specified and as directed. |
| 10 | S&F mild steel framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanksand similar work conforming to Fe 290 Gde-E-165 complete all as specified and directed. |
| 11 | S & F in repairs curtain rails, harrison rail, aluminium alloy chromium plated with fixing brackets, stops, rollers etc complete all as specified and directed. . |
| 12 | S&F Anodised aluminum section powder coated in partition / frame for door, shutters, sliding windows / ventilators and places otherwise not specified cut to size, jointed with cadmium plated steel screws, including rubber beading or gaskets for fixing glass or wire cloth or Bakelite sheet and all necessary fittings, hinges, screws, plugs, locking arrangements for windows, Nylon ball bearing etc completed all as specified and directed (Aluminum section shall be of make Jindal / Hindalco / Indalco).Note :- Weight of Aluminum sections for frames and shutters shall be only considered for payment.Cost of other consumables required for the item shall be deemed to be included in the quoted rate.However glass panes / Bakelite sheet / wire cloth / mortice lock / locking stay / floor spring / floor door stopper will be measured and paid separately under respective items. |
| 13 | M&L for anodised aluminium window and ventilator shutters, fixed type, with or without sash bar, using aluminium section weighing not less than 0.55Kg per metre including necessary joining cleats, glazing clips, rubber neoprene packing, anodised aluminium snap beading, screws etc complete all as specified and as directed. |
| 14 | S&F aluminium sliding window with powder coating (minium thickness of powder coating 50 micron) including following components / specification complete all as specified and directed.(i) Thickness and weight per metre length of aluminium frame and section of shutter all as shown on drawing. (ii) All vercal/ horizontal joint shall be of extruded aluminium section so as to avoid any play between jointed members. (iii) all other accessories such as jointing cleats, glazing clips, rubber neoprene packing, anodised aluminium snap beading, srews, etc. (iv) Stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aparture 1.40 mm and fixed with stainless steel wire staples, etc. (v)Sheet glass 4 mm thick selected quality tinted/black glass and glazing with oil putty or fixed with wooden beads in square not exceeding 0.5 Sqm in each pane (vi) Rest all as specified in drawing no CEZ/2015/TD/007 Sheet no 1R/5, 2R/5, 3R/5, 4R/5, 5R/5. Note :- Grill shall be measured and paid separately. |
| 15 | S&F Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement complete all as specified and directed. |
| 16 | S&F 4mm thick figured glass pin headed type and glazing with oil putty in square n.exc.0.50 Sqm in each pane complete all as specified and as directed. |
| 17 | M&L for providing and injecting chemical emulsion for post constructional anti termite treatment along the external wall below concrete or masonry apron using chemical emulsion at the rate of 2.25 litre peri linear metre including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 Cement : 2 Coarse sand) to match the existing floors drilling and plugging holes etc complete all as specified and as directed. |
| 18 | M&L for Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors complete all as specified and directed. |
| 19 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and removing the rubbish off the premises complete all as specified and as directed. |
| 20 | M&L for non skid ceramic colouredtiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles with over and including 15mm thick screed bed or bedding layer of cement morter (1:6) for laying of floor finishes complete all as specified and directed. |
| 21 | M&L for non skid ceramic colouredtiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles with over and including 15mm thick screed bed or bedding layer of cement morter (1:6) for laying of floor finishes complete all as specified and directed. |
| 22 | M&L for coloured 450x350x7-8 mm thick glazed ceramic tileson vertical surfaces such as skirting, dado and risers to steps etc, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match, over and including 10mm thickbacking coat in cement mortar (1:4) , complete all as specified and directed. |
| 23 | Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc. complete all as specified and directed. |
| 24 | M&L for 75mm thick PCC (1:4:8) type D-2 (using 40mm graded crushed stone aggregate) as in sub base of flooringcomplete all as specified and directed. |
| 25 | M&L for Marble work 18-20 mm thick (table rubbed and Mirror finish polished) (Colour- Green) in steps, jambs, pillars, window cills, cooking platforms and like in vertical surfaces over and including 10 mm thick screed bed of cement mortar (1:3) including pointing in white cement (1:2) using marble dust with admixture of pigments to match with marble of any shade other than white and black complete all as specified and directed. |
| 26 | Demolition of brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as directed. |
| 27 | M&L for brick work with sub class \"B\" well burnt clay bricks straight or curved on plan exc 6 meter mean radius built in cement mortar 1:6 complete all as specified and directed. |
| 28 | M&L for brick work with sub class \"B\" well burnt clay bricks straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and directed. |
| 29 | Taking down cement plaster or cement lime plaster on walls /ceiling of any description from concrete or brick wall etc including raking out joints, hacking for key, scrubbing down with water and disposing off the retreived debris as directed including necessary scaffoldings etc complete all as specified and directed. |
| 30 | M & L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 and finished the surfaces even and smooth without using extra cement complete all as specified and directed. |
| 31 | M&L for rendering 15 mm thick on fair faces of external wall of brick work or stone surfaces in two layers (10 mm and 5 mm thick) in cement mortar in (1:4) using water proofing compound in top layer as per manufactrure infrastructure andfinished even and smooth (without using extra lime or cement) complete all as specified and directed.Note:Water Proofing Compound shall be measured and paid for separately. |
| 32 | M&L for Rough cast plaster on exterior wallsapplying the under coat of cement and sand morrtar 1:3 not less than 10mm thick and while it is still in plastic state the roughcast mixture consisting of crushed stone or fine gravel aggregate (size between 6 to 12mm ) mixed with coarse sand and cement in the raio of 1:1:1 shall be applied and finished even.The mix of cement and sand shall made slightly wetter than normal for rendering to ensure that larger aggregate are thoroughly covered completeall as specified and directed by Engineer in Charge |
| 33 | M&L for rendering 5mm thickin cement morter (1:3) on ceiling surfaces, finished even and smoothwithout using extra cement, complete all as specified and directed. |
| 34 | M&L for applyiing 15mm plaster with polymer modified mortar fortified with SBR(Nito Bond SBR 45) in proportion 1:3 by weight 5 litr Nitobond SBR 45 added to 50kg cement with 13 litr water and finished surfaces to existing adjoining surface of ceiling, columns, beam and like etc complete all as specified and directed |
| 35 | Supply only Water Proofing Compound ISI marked of approved make complete all as specified and directed. |
| 36 | M&L for preparation of new plastered surfaces of walls and applying two coats of colour wash over one coat of white wash complete all as specified and as directed. |
| 37 | M&L for preparation newly plaster surfaces of wall, chajja, facia etc and applying two coats of 100% premium Acrylic emulsion paint having VOC less than 50 gm/ litre and UV resistant as per IS-15489:2004 alkali and fungal resistant exterior paint of required shed (company depot tinted)with silicon additives 1.43 litrs/ 10 Sqm over and including primer coat of exterior primer applied 0.90 litre/10 Sqm over new surfaces using Airless spray technology with maximum working pressure of 3300 PSI and capable of operating single spray gun with a maximum material hose length of 30 mtr, the spray machine shouldbe of reputed manufacturer with pro guard technology and capability of tracking pressure and paint usage and certified by paint manufacturer and as mentioned in PS and acessories complete all as specified and directed. |
| 38 | M&L for complete removal of existing treatment from walls and applying two or more coats of 100% premium Acrylic emulsion paint having VOC less than 50 gm /litre and UV resistantas per IS 15489:2004 alkali and fungal resistant exterior paint of required shed(company depot tinted) with silicon additives1.43 lits/10 sqm over and including primer coat of exterior primer applied 0.90 litre/10 sqm over a coatof 1mm thick putty over plastered surface to prepare the surface even and smooth complete all as specified and directed . |
| 39 | M&L for applying two coat of white wash on old decorated Ceiling surface including preparation of surface, complete all as specified and directed. |
| 40 | M&L for applying three coats of white wash on ceiling surface including preparation of new surface, complete all as specified and directed. |
| 41 | M&L for preparing of new steel surfaces of any description , over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer, complete all as specified and directed. |
| 42 | M&L for 75 mm thick plain cement concrete (1:3:6) Type C2 using 40 mm graded aggregates as in plinth protection/paving including finishing surface even and fair without using extra cement complete all as specified and directed |
| 43 | M&L for forming Construction joint 30mm deep x10mm wide filled with sealing compound, Grade ‘A’, complete all as specified and directed. |
| 44 | S&F framed work as in doors or gates of angle or other section with gusset plates, rails, braes, etc, complete drilled for fixing pof steel sheeting or other covering. Doors, etc, to be prepared for hanging or slidiong with and including either hooks and hinges or steel hanging door fittings (exclusive of steel, sheeting or other covering, running rails and guides) and hanging, also fastening including fabrication and fixing, complete all as specified and as directed. |
| 45 | Taking up or down 15mm bore steel tubing and connections including cleaning for refixing or removal from site complete all as specified and as directed. |
| 46 | Taking up or down 20mm bore steel tubing and connections including cleaning for refixing or removal from site complete all as specified and as directed. |
| 47 | Refixing old steel tubing 15mm bore and connections in new or old position (walls/ceilings/floors etc) with new fittings complete all as specified and directed. |
| 48 | S&F 15 mm bore medium grade galvanized steel water tubingwith all fittings, fixed to wall/ceiling or laid in floor complete all as specified. |
| 49 | Refixing old steel tubing 20 mm bore and connections in new or old position (walls/ceilings/floors etc) with new fittings complete all as specified and directed. |
| 50 | S&F 20 mm bore medium grade galvanized steel water tubingwith all fittings, fixed to wall/ceiling or laid in floor complete all as specified and directed. |
| 51 | M&L for cutting chases, pinning in making good to facings where required and pointing in cement motar (1:3) to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc and cutting chases for concealed water tubing or concealed conduit wiring, etc and making good, cutting not exc 10 cm girth in brick walls complete all as specified and directed. |
| 52 | S&F 20 mm bore CPVC tubings \"medium grade\" with all fittings & fixed complete to walls & ceilings or laid in floors complete all as specified and directed. |
| 53 | S&F in repairs for MS grating CP 75/100mm dia, without hole and with hole for waste pipe of approved make including fixing with CM to floor/nahani traps etc complete all as specified and directed. |
| 54 | S & F in repairs 15 mm bore Bip taps, Chromium plated cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferruleand fixed complete all as specified and directed. |
| 55 | S&F in repairs, stop valves, 15 mm bore cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions as specified and directed. |
| 56 | S&F in repairs, 15mm bore, PVC connection pipe 450mm long with PTMT nuts at both ends complete all as specified and directed. |
| 57 | S&F in repair Brass chromium plated Tubular towel rail 20mm dia, D type, 60cm long between flanges all as specified and as directed. |
| 58 | S&F in repairs Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed. |
| 59 | S&F in repairs stainless steel peg set of 6 peg, 45 cm long, fixed with stainless screws complete all as specified and directed. |
| 60 | S&F in repair soap dish of stainless steel fixed to wall with chromium plated brass screws complete all as specified and as directed |
| 61 | S&F in repairs flexible (coil shaped) PVC waste pipe for sink and wash hand basin 32/40mm dia, length not less than 70 cm, connected to PVC waste coupling/fittings complete all as specified and directed. |
| 62 | S&F in repairs, 10 litres capacity PVC valveless syphonic action type, dual type flushing cistern (ISI marked), low level with inlet, ball valve, float bracket & flush pipe complete all as specified & directed. |
| 63 | S&F in repairs Vitreous china wash basin, white,flat back, size 550 x 400 mm with brackets, PVC connection of 450 mm long and PVC(HDPE) 32 mm bore waste pipe, brass couplings 32 mm CP etc complete all as specified and directed. |
| 64 | S&F in repair 15 mm bore pillar taps, cast copper alloy, chromium plated, fancy type with capstan heads, screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and fly nuts, screwed for iron pipe as specified. |
| 65 | S&F Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) front or back inlet including connection to drain (or outgoing pipe) and to flushing pipe, anti-syphonage pipe, etc and making good to floor complete all as specified and directed. |
| 66 | S&Fin repairs, vitreous China squatting pan, \"Orissa\"pattern, size 580mm x 440 mm, white with integral foot rest and \"P\" or \"S\" trap, including provision of lime concrete bedding, connection to trap and flushing pipe etc complete including making good to disturbed surfaces of floor to match with existing specifications complete all as specified and directed. |
| 67 | S&F in repairs plastic water closet seat cover white closed pattern with flat bottom and mild steel CP or aluminium hinging device complete all as specified and directed. |
| 68 | S&F in repair for Vitreous China urinals,half stall (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing grating and Union for discharge pipe incl CP 40mm waste coupling and PVC 40mmwaste pipe 900mm long complete all as specified and directed. |
| 69 | S&F in repair Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms) complete all as specified and directed. |
| 70 | S&F 1000 litres capacityrotational moulded polyethylene water storage tanks (cylindrical or vertical with closed top) as per IS 12701:1996, hoisted and fixed in position including provision of 20/15mm bore medium grade pipe for connecting inlet, outlet, overflow and washout pipe 20 mm bore, ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed. (minimum weight 20 mm - 210 gms )complete all as specified and as directed. |
| 71 | S&F Ball valves high pressure of PTMT 20 mm bore with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight - 210 gms), screwedfor iron pipe etc complete all as specified and directed. |
| 72 | S&F in repair 20 mm bore Gun metal gate or globe valve with iron wheel head screwed both ends for iron pipe complete all as specified and directed. |
| 73 | S&F in repair 600mmX450mm bevelled edge mirror of selected quality 5mm thick glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated cup washers and screws complete all as specified and directed. |
| 74 | S&F mild steel work as in Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates, hook and pintle hinges, large hasps and staples, chains, hand made sliding bolts, clamps, hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters, knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde E-165 complete all as specified and directed. |
| 75 | M&L for PVC (SWR) floor trap 100 dia, with grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) complete all as specified and directed. |
| 76 | M&L for PVC (SWR) floor trap 75 dia, with grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) complete all as specified and directed. |
| 77 | M&L for water proofing treatment on RCC roof etc. comprising with the following operation & as specified herein below:-(a)Taking down existing old tarfelt, bituminous compoundincluding cleaning & removing debris to a distance exc 100 m n.exc.250m.(b) M&L 25 thick cement concrete type B0 1:2:4 (12.5 mm graded aggregate) finished even and smooth.(c) Cutting out cracks to V-section in existing roofs or terracing, cleaning out and filling solidly with a hot mixture of bitumen and clean dry sand 1:1 (by weight). (d) M&L for 20 mm thick screed bed in cement mortar 1:4 finished even and smooth.(e) Preparing & cleaning of fully dried cement plastered surface.(f) Applying one coat of cold bituminous primer to the plastered surface @ 0.25 liters per sqm conforming IS-3384.(g) A layer of APP based polymeric membrane3mm thick (minimum) weighing 3.5 kg per sqm reinforced with polyester non woven fabric(weighing not less than 160 gms/sqm) shall be applied over bituminous primer as specified above.Application of polymeric membrane shall be by torch application. The over lap shall be minimum 100 mm on transverse direction and 75 mm in longitudinal direction.(h) One coat of aluminium paint over APP membrane @0.11Kg/Sqm.Note:-Prior to execution of the APP Membrane works, leak proof test shall be done by ponding water on roof slab to minimum depth of 25 mm. The entire roof slab shall be flooded with water for 48 hours. The necessary barrier shall be made to make feasible to stagnate water for 48 hours on roof slab. |
| 78 | M&Lfor special treatment for sunken portion of WCs/ Bath & toilet executed in following stages:- Stage 1 :- Demolition of WC including lime concrete and cement concrete etc and preparing the surfaces of existing sunken portion of WCs or bath etc with wire brush to remove all loose dirt, oil grease etc including removing debris from site of work etc . Stage 2:- Providing10mm thick plaster in CM 1:3 mixed with integral water proofing chemical of Dr. Fixit Pidicrete URP or plaster seal of STP Ltd in the proportion/quantity all as per Manufacture\"s instructions.Complete.Stage 3:-Apply Dr Fixit Primeseal primer or Equivalent of STP Ltd (and allow to dry for 8 hours) all as per Manufacture\"s instructions. Stage 4:-Apply two coats of water proofing elastomeric coating system of Dr Fixit Raincoats with DFT 100 Micron or shalicry 215 of STP (The surface after painting one coats shall be allowed to dry for 6 hours before next coats) all as per Manufacturer\"s instructions. Stage 5:-Rendering 10mm thick in CM 1:3 mixed with Integral water proofing chemical Dr Fixit Pidicrete URP or plaster seal of STP Ltdall as per Manufacture\"s instructions.Stage 6.All CI joints shall filled with mixture of cement fine sand and plaster seal of STP Ltd or Dr Fixit pidicrete URPall as per Manufacture\"s instruction. Stage 7:-Making holes in wall and fixing600mm long 40mm dia medium grade GI spout for draining the surplus water if any. Stage 8:-Carry out ponding test for 48 hours to ensure water tightness of repaired sunken portion water tightness of repaired sunken portion andfilling of sunken portion for cement concrete Type E2 1:5:10 using 40 mm graded aggregate as in lean concrete complete all as specified and directed. Note :- (a) Only plan area shall be measured and accounted for payment under this item. (b)Depth of sunken portion of WC\"s/Baths shall be upto 35cm, which is to be taken into account while quoting the rate against this item.(c) Rate quoted by Contractor shall be deemed to be included for all the horizontal and verticale treated surfaces of sunken portions of WC & Bath. |
| 79 | M&L for 15-18mm thick Artificial granite (of any type) (table rubbed and polished) in steps, jambs, pillars of gate and similar work in cement mortar (1:4)including pointing in white cement (1:2) using marble dust with admixure of pigment to match the shade of granite complete all as specified and directed. |
| 80 | M&L for rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and as directed. |
| 81 | Demolition of reinforced concrete (reinforcement cut as required to facilitate demolition) of any description and in any position not otherwise specifically provided for, removing rubbish off the premises etc complete all as specified and directed. |
| 82 | M&L for RCC (1:2:4) type B-1 (using 20 mm graded broken stone aggregate) as in slab supported on walls, beams and column in floors, roof landings, balconies, canopies, deck slabs and in shelvescomplete all as specified and directed. (Note : Reinforcement shall be measured and paid seperately under relevant) |
| 83 | M&L for TMT bars 10 mm dia and over, as reinforcement for concrete cut to length, bent to shape required including cranking, bending, spirally hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia, complete all as specified and directed. |
| 84 | M&L for formwork to soffits of suspended slabs such as roof slab, floor slabs, landing covers, and similar works,for rough finished flat surfaces of concrete, thickness of slab not exc 200 mm,complete all as specified and directed. |
| 85 | M&L for formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete rail ings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizon tal or sloping and similar work exc 10cm but n exc 20cm widecomplete all as specified and directed. |
| 86 | Demolition and breaking up to 150mm bore drain pipes (SGSW/AC/RCC) set in cement mortar including cement concrete bedding and removal of debris/rubbles etc to a distance not exceeding 50m complete all as specified and as directed. Note : Necessary excavation and earth work shall be measured and paid seperately. |
| 87 | M&L for salt glazed stone ware drain pipes 150 mm bore, grade \"A\" laid in trenches, jointed cement mortar and tested complete all as specified and directed. |
| 88 | M&L for PCC 1:4:8 type D-2 using 40 mm graded crushed stone aggregate in bedding to SGSW/NP2 drain pipes, including packing under and haunching against the sides of pipes after they are laid and tested complete for 150 mm bore pipe all as specified and directed. |
| 89 | M&L for cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required for 150mm internal dia of pipe complete all as specified and directed. |
| 90 | S&F 50mm thick steel fibre reinforced (SFRC) man hole cover with iron frames (medium) complying to the standard specifications as mentioned in the IS 12592 BIS Standard minimum load bearing capacity 5 ton/Sqm in square, rectangular shape of size 300X300, 450X450, 600X600 complete all as specified and directed. |
| 91 | S&F in repairs PVC (SWR) pipes 75mm bore single socketed, in any length with rubber ring joints laid in trenches or in floors, complete all as specified and directed. |
| 92 | S&F 10mm bore, PVC (SWR) pipes type \"B\", single socketed in any length with rubber ring joints fixed to walls using MS holder bat, fixed complete all as specified and directed. |
| 93 | S&F 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls complete all as specified and directed |
| 94 | S&F PVC (SWR) bends any radius with access door, 110mm bore complete all as specified and directed. |
| 95 | S&F PVC (SWR) bends any radius, 110mm bore complete all as specified and directed. |
| 96 | S&F 75 mm bore, PVC (SWR) vent cowlfixed with solvent cement complete all as specified and as directed. |
| 97 | S&F PVC (SWR) bends any radius, 75mm bore complete all as specified and directed. |
| 98 | S&F PVC (SWR) bends any radius with access door, 75mm bore complete all as specified and directed. |
| 99 | S&F 110 mm bore, PVC (SWR) vent cowlfixed with solvent cement complete all as specified and directed. |
| 100 | Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc complete all as specified and directed. |
| 101 | Taking down carefully MCB DBs any type and size complete all as specified and directed. |
| 102 | Taking down carefully old unsv lights of any type and size complete all as specified and directed. |
| 103 | M&Lfor concealed point wiring with two runs of FRLSH PVC insulated unsheathed, 1100 V grade cable multi stranded copper conductor of size 1.5 sqmm and one single core FRLSH PVC insulated unsheathed stranded copper conductor of size 1.50 sqmm green in colour as earth lead, drawing through in and including PVC rigid conduit of size not less than 20mm, with all fittings & accessories including provn of MS sunk terminal box of appropriate size suitable for switch fixed flush to wall for mounting switch, sockets, fan regulators etc with 3mm thick hylum sheet top cover with screws & cup washers including cutting chases and making good by using cement mortar 1:4 complete for one light / fan point / call bell complete all as specified and directed. |
| 104 | All as per Item No.103here in above but for One 2/3 pin socket outlet 5/6Amps on independent board |
| 105 | All as per Item No.103here in above but forOne 2/3 pin socket outlet 5/6 Amps on the same board with other switches. |
| 106 | All as per Item No.103here in above but for one switch socket combination 15/16 Amps on independent board with cable 4 sq mm size and earth wire 4 sqmm |
| 107 | S&F Switch piano, flush type, single pole, one way switch5 Amps ISI marked complete all as specified and as directed. |
| 108 | S&F Switch socketcombination 2 in 1, 3/5 Pin,5 Amps flush type, ISI marked complete all as specified and as directed. |
| 109 | S&F socket outlet, 2 in 1, 3 pin, 5 Amps, 240V bearing ISI marked complete all as specified and as directed. |
| 110 | S&F Switch socketcombination multipurpose 2 in 1,3/5 Pin, 15/16 Amps flush type, ISI marked complete all as specified and as directed. |
| 111 | S&F angular/batten holderPVC/Polycarbonate suitable for batten fittings including oneLED Lamp of 9W minimum 4 hrs backup of complete all as specified and directed. |
| 112 | S&F Ceiling rose surface PVC, 3 terminals 65x50mm ISI marked complete all as specified and as directed. |
| 113 | S&F motion sensor LED fitting 01x20W, interver batten holder with 2000 lumen 220 volts AC decorative box type with driver with aluminium housing, LED tube light connecting up to 3 core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed. |
| 114 | S&F in repair of MCB Distribution board SPN 4 Way for mountingSPN/ SP MCBs as Incoming / outgoing, factory made, confirming to IS, fabricated out of CRCA sheet , fitted with DIN channel, neutral link and suitable rated bus bar, DBs shall be semi glossyfinished with epoxy polyester based powder paint sprayed and backed at high temperature, between powder paint process the sheet steel having to go through the anti rust conditioning in not less than seven tank process to ensure smoothfinish and protection against corrosion atmosphere. The DBs shall be double door type with hinged door with locking arrangement. The DBs shall be of IP 43 - IK 09 with metal door complete all as specified and directed. |
| 115 | S&F miniature circuit breaker (MCB)SPN 6 to 32 Amps\"C\" Series 10 KA 240 volts complete all as specified and directed. |
| 116 | S&F miniature circuit breaker (MCB) SP, 240 Volts,6 to 32 Amps, \"C\" Series, 10KA capacity complete all as specified and directed. |
| 117 | M&L for sub main wiring with two run of 4 Sqmm (Nominal area) single core cable PVC insulated, multistranded, unsheathed, copper conductor cables (FRLSH), 1100 Volts grade drawn through PVC casing-caping/conduit of suitable size,fixed to wall/ceiling etc including one run of 4 Sqmm (nominal area) single core, PVC insulated, multistranded, unsheathed, copper conductor(FRLSH) as earth wire and duly connected to common earth point complete all as specified and as directed.Note : (a) PVC Casing-caping/conduit, two run wiring cables and one run of earth wire will be measured as one length (b) All incoming and outgoing cable shall be connected by using proper lugs & sockets. |
