|
| 1 | Earth work in Excavation in trenches for foundations pipes cable etc in ordinary soil (Loam clay or sand) including lift upto 1.5 m. lead upto 50m and dressing of sides and rammings of bottom and disposal of surplus exdavated earth as directed by the Engineer I/C within a lead of 30 m. S.I No. 251 |
| 2 | Construction of embankment with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacting to meet requirement of table 300-2. for raising of Embankment. |
| 3 | Construction of embankment with approved materials deposited at site from roadway cutting and excavation from drain and foundation of other structures graded and compacted to meet requirement of table 300-2. |
| 4 | Construction of sub-grade and earthen shoulders with approved material obtained from borrow pits with all lifts & leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of table No. 300-2 |
| 5 | Construction of embankment with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacting to meet requirement of table 300-2. for raising of Embankment. (cartage 3km) |
| 6 | Construction of granular sub-base by providing coarse graded Material, mixing in a mechanical mix plant of OMC, carriage of mixed Material to work site, spreading in uniform layers with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per clause 401 in a compacted layer of 100mm functioning as drainage layer. |
| 7 | Providing,laying, spreading and compacting graded stone aggregate to wet mix mcacdam specified including premixing the material with water at OMC in mechanical mix plant carriage of mixed material by tipper to site, laying in uniform layers with paver in sub-base/base course on well prepared surface and compacting with vibratory roller to achieve the desired density. |
| 8 | Providing and applying primer coat with bitumen emulsion (SS-2) on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.70 kg/sqm using mechanical means as per Technical Specification Clause 502 |
| 9 | Providing and applying tack coat II (on existing bitumenos surface) with bitumen VG-10 using bitumen pressure distributor @0.20Kg/sqm on the prepared surface cleaned with mechanical broom.(Existing bitumenos surface) |
| 10 | Providing and laying dense graded bituminous macadam with 60-90 TPH batch type hot mix plant producing an average output of 75 tonne per hour using crushed aggregate of specified grading. premixed with bituminous binder @ 4.5 % by weight of total mix and fillar, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled vibratory and tendem rollers to achieve the desired compaction as per MORT&H specification clause 507 complete in all respect (Including crossing and juction) |
| 11 | Providing and applying tack coat-II with bitumen VG-10 using bitumen pressure distributor @0.20Kg/sqm on the prepared surface cleaned with mechanical broom. (Including crossing and juction) |
| 12 | Providing and laying bituminous concrete with 60-90 TPH batch type hot mix plant producing an average output of 75 tonnes per hour using crushed aggregates of specified grading, premixed with bituminous binder @ 5.4 to 5.6 per cent of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MORTH specification clause No. 509 complete in all respects (Including crossing and juction) |
| 13 | Construction of un-reinforced, dowel jointed, plain cement concrete pavement over a prepared sub base with 43 grade cement @ 400 kg per cum, coarse and fine aggregate conforming to IS 383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a batching and mixing plant as per approved mix design, transported to site, laid with a fixed form or slip form paver, spread, compacted and finished in a continuous operation including provision of contraction, expansion, construction and longitudinal joints, joint filler, separation membrane, sealant primer, joint sealant, debonding strip, dowel bar, tie rod, admixtures as approved, curing compound, finishing to lines and grades as per drawing |
| 14 | Providing and laying of Hecto Meter Stone ( Mirzapur Stone ) of standard design as per IRC-8 fixing in position including painting of Hecto Meter Stone with 2 coats of approved synthetic enamel paint and lettering as per PWD maintenance manual including cost of Hecto Meter Stone transpotation to site and all materials, labour T&P etc. required proper complete of work. |
| 15 | Providing and laying of KM Stone ( Mirzapur Stone) of standard design as per IRC-8 fixing in position including painting of KM stone with 2 coats of approved synthetic enamel paint and lettering as per PWD maintenance to site and all materials, labour T&P etc. required proper complete of work |
| 16 | Providing and laying of 5Th KM Stone ( Mirzapur Stone) of standard design as per IRC-8 fixing in position including painting of KM stone with 2 coats of approved synthetic enamel paint and lettering as per PWD maintenance to site and all materials, labour T&P etc. required proper complete of work |
| 17 | P/L of hot applied thermo plastic compound 2.5 mm thick including reflecto rising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass breads as per IRC 35.The finished surface to be level uniform & free from streaks and hole. in edges and center line. |
| 18 | Road Furniture- Reflective Caution Boards -Providing and erecting direction and place indentification retro reflectise signs as per IRC 67 made of high intensity grade sheeting fixed over aluminum sheeting 2 mm thick supported on a mild steel single angle iorn post 75X75X6 fixed to the ground complete as specfied .80mmx60mm Rectangular with difiniation plate 20cm x60 cm |
| 19 | Supply and errection of builtup cantilever structure comprising of one vertical post of 6 mtr height made up of 300 mm NB heavy class MS pipe as vertical member welded with 10 mm MS plate at top & bottom for bearing of horizental frame comprising of 40 mm NB made hevy class main pipe as of 25 mm medium class NB pipe bracing as per approved design drwaing with one coat of steel primer and two coat sinthethic enamel paint complete the work includes construction of RCC foundation of size 0.75 X0.75 X 1.20 mtr. deep for builtup overhead structure including E/w in exvation 10 mm thick lean concreat in 1:4:8 & R.C.C. with 1:2:4 cement , Coarse sand , 20 mm stone grit . including supply grouting of 25mm dia foundation bolt (600 mm long) as provision for structure including cost of reinforcement and suttering etc. complete |
| 20 | Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 mad of high intensity grade sheeting vide clause 801.3, fixed cover aluminium shting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x75 mm x6 mm firmly fixed to th ground by means of properly dsignd foundation with M-15 grade cment conc. 45 cm x 45 cm x 60 cm, 60 cm below ground lvel as per approved drawing (Chevron Double 155x60 Cm |
| 21 | Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 mad of high intensity grade sheeting vide clause 801.3, fixed cover aluminium shting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x75 mm x6 mm firmly fixed to th ground by means of properly dsignd foundation with M-15 grade cment conc. 45 cm x 45 cm x 60 cm, 60 cm below ground lvel as per approved drawing (Hazard left / right) size 30cmx90cm |
| 22 | Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 mad of high intensity grade sheeting vide clause 801.3, fixed cover aluminium shting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x75 mm x6 mm firmly fixed to th ground by means of properly dsignd foundation with M-15 grade cment conc. 45 cm x 45 cm x 60 cm, 60 cm below ground lvel as per approved drawing (Stop ) sizc 90cm hight Octagon |
| 23 | Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 mad of high intensity grade sheeting vide clause 801.3, fixed cover aluminium shting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x75 mm x6 mm firmly fixed to th ground by means of properly dsignd foundation with M-15 grade cment conc. 45 cm x 45 cm x 60 cm, 60 cm below ground lvel as per approved drawing ( T junction)Size 60cm eqilateral triangle |
| 24 | Thermoplastic Repeted Bar marking is a softer treatment to reduce the speed. One set of bar marking (refer TM 08) comprises of 6 bars of 300 mm wide. Each strip of thermoplastic strip shall be of 5 mm high and shall be set applied across the full width of the carriageway. |
| 25 | HUME PIPE (900mm&600mm) - E/W in excavation in foundation in ordinary soil including lift 1.50 mtr and lead up to 30 mtr and including filling watering ramming of excavated earth into the trenches or into the space of between the building and side the foundation trench or into the plinth and removal and disposal of surplus earth as per direction by E/I as per S.I. No. 3.5(1) |
| 26 | Concrete with 4 cm gauge brick ballast, fine sand of 1.25 fineness modulus and cement in proportion of 1:4:8 in foundation and under flooring supply of all materials, labour and T&P etc. requuired for propar completion of the work as per Sl.No. 275 |
| 27 | Supply & Laying of 15mm brick ballast mixed with sand below pipe as bedding in 15cm thickness and in haunch of pipe upto 1/10 of outer dia pipe. |
| 28 | Clas-150 brick work with 1:4 cement and coarse sand in foundation and plinth including supply of all materials labour and T&P etc. Requuired for proper completion of work as per S.No. 11.5 |
| 29 | Struck pointing in 1:2 cement & fine sand mortar on brick work including supply of all materials, labour and T&P etc Requuired for proper completion of work as per S.I No. 574 |
| 30 | Concrete with 20 mm gauge approved stone grits in the proportion of 1:2:4 including supply of all materials labours and T&P etc. Required for completion of the work as per S.No. 279(B) |
| 31 | 12mm thick plaster with cement mortor with cement and fine sand of mortor in 1:4 SI.No. 584 |
| 32 | Supply of 600 mm dia NP-3, S&S Hume Pipe including cartage upto site laoding, unloading and all Taxes etc. |
| 33 | Colour washing |
| 34 | Lettering and painting of culvert no. Plate 30x30cm of standard size with two coats of approved synthetic enamel paint and lettering as per PWD maintenance manual including cost of all materials, labour T&P etc. complete. |
| 35 | 5-Supply and laying of 900mm dia NP3 hume pipe. |
| 36 | RCC CULVERT EXTENTION -Earth work in Excavation in trenches for foundations pipes cable etc in ordinary soil (loam clay or sand) including lift upto 1.5m lead upto 50m and dressing of sides and rammings of bottom and disposal of surplus exdavated earth as directed by the engineer I/C within a lead of 30m. as per S.I. No.-251 |
| 37 | Providing and laying cement concrete 1:4:8(1 cement : 4 fine sand : 8 graded brick aggregate 40mm nominal size) including supply of all materials. Labour and T&P etc. required for proper completion of the work and curing complete, also including cost of formwork in foundation and floors.. as per S.I. No.-275 |
| 38 | Class-150 brick work with 1:3 cement and coarse sand mortar in foundation and plinth including supply of all materials labour and T&P etc. required for proper completion of the work. as per S.I. No.-30 |
| 39 | R.C.C. work with cement approved coarse sand and 20mm gauge stone grit in the proportion 1:1:5:3 for slabs excluding supply of reinforcement and its binding but its fixing and binding the same with 24BWGGI binding wire and including necessary centering and shuttering etc. and also including supply of materials labour and tools and plants etc. required for proper completion of the work, Binding wire cost being included in the item as per SI No. 283(b) |
| 40 | Supplying, fitting and placing HYSD bar reinforcement in supper Structure complete as per drawing and technical specifications |
| 41 | Struck pointing in 1:2 Cement & fine sand mortar on brick work including supply of all materials, labour and T&P etc. required for proper cmpletion of the work. as per S.I.No.574 |
| 42 | Providing and laying cement concrete 1:2:4(1 cement : 2 coarse sand : 4 graded brick aggregate 20mm nominal size) including supply of all materials. Labour and T&P etc. required for proper completion of the work and curing complete, as per S.I.No.-279(b |
| 43 | Providing and laying of weephole in brick massonary in abutment with 100mm dia PVC pipe extending through the full width of the structuer with slope of 1v:20H toward drawing force complete as per drawing and technical specification (MORTH &H-13.8/2706&2200) |
| 44 | Colour washing |
| 45 | Providing painting of culvert no Plate 30x30ccm of standard size with two coats of approved synthetic enamel paint and as per PWD maintenance manual including cost of all materials, labour T&P etc. complete |
| 46 | Filling braickbats as filler material betwe3en roadcrust and abutment |
| 47 | DRAIN - Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom and backfilling with approved material. Technical Clause 304 of MoRTH Specification. |
| 48 | Plain cement concrete 1:3:6 nominal mix in foundation with crushed aggregate 40 mm nominal size mechanically mixed, placed in foundation and compacted by vibration including curing for 14 days. Technical Specification as per Section 2100 of MoRTH Specification. |
| 49 | Plain/Reinforced Cement Concrete in Open Foundation complete as per Drawing and Technical Specifications as per Section 1500, 1700 & 2100 of MoRTH Specification. |
| 50 | Supplying, Fitting and Placing un-coated HYSD bar Reinforcement in Foundation complete as per Drawing and Technical Specifications as per Section 1600 of MoRTH Specification. |
| 51 | Routine Maintenance of road after completion of work :-(A) Carriageway/ Pavement:(a) Potholes, cracks, other surface defects (SWMM & BC), (b) Repair of Edges, Rutting (BC)(B) Road, Embankment, Cutings, Shoulders, Trees & Plantation :(a) Road Maintained free of edge drop, inadequate cross fall, undulations, settlement, Ponding (E/W), (b) Deficent slopes, rain cuts in embankments (E/W), Vegetation growth, Loping of tree branches.(C) Bridges and Culverts:(a) De-Silting, (b) Clearing vegetation growth (Jungle Clearance), (c) Damaged/distrubed boulder pitching, breast/toe wall retaining wall, apron flooring, guide bunds (Boulder Apron), (d) Parapet, any damage to foundations, (e) Any defects in sub-strucures, (f) Any defects in superstructures, raillings, parapets. (g) Wearing coat, (h) Approach slab, (i) Painting & Lettering of No. plates, repair.(D) Repair of Roadside Drains:(a) Brick Work in 1:4, (b) Plaster, (c) CC- 1:2:4.(E) Road Furniture:(a) Cleaning, Painting & lettering of stones & sign boards, Replacement of damaged/ missing stone & sign boards. (b) 200 m Stones, (c) Km stones, (d) 5th km stones.Maintenance requriment as per above and Mentioned in Special Condition of Contract for Maintenance.Payment of Maintenance work as Percentage of final Civil Construction Cost : |
| 52 | a) For 1st Year @ 0.00% |
| 53 | b) For IInd Year @ 0.25% |
| 54 | c) For IIIrd Year @ 0.50% |
| 55 | d) For IVth Year @ 0.75% |
| 56 | e) For Vth Year @ 1.00% Please Enable Macros to View BoQ information |
