|
| 1 | Surface dressing of the ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50m and lift up to 1.5m Including cost of all materials, conveyance, loading and unloading, labour, hire charges, fuel, tools and plant, all applicable taxes, and incidental charges, complete as directed by the Engineer-in-Charge |
| 2 | Supplying and filling in foundation, basement, etc with filling sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers. Including cost of all materials, conveyance, loading and unloading, labour, hire charges, fuel, tools and plant, all applicable taxes, and incidental charges, complete as directed by the Engineer-in-Charge |
| 3 | Cement Concrete 1:4:8 (One Cement, Four Sand and Eight hard broken stone aggregate) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification Including cost of all materials, conveyance, loading and unloading, labour, hire charges, fuel, tools and plant, all applicable taxes, and incidental charges, complete as directed by the Engineer-in-Charge |
| 4 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level TMT Bars ; Including cost of all materials, conveyance, loading and unloading, labour, hire charges, fuel, tools and plant, all applicable taxes, and incidental charges, complete as directed by the Engineer-in-Charge |
| 5 | Providing, hoisting and fixing precast reinforced cement concrete (RCC) mouldings above plinth level up to floor five level, such as cornices, window sills, etc., including setting in cement mortar 1:3 (1 cement : 3 coarse sand), and including the cost of required centering and shuttering, but excluding the cost of reinforcement, with RCC mix 1:1.5:3 (1 cement : 1.5 coarse sand (Zone-III) derived from natural sources : 3 graded stone aggregate of 20 mm nominal size derived from natural sources), complete and in compliance with standard specifications.Note: As per site conditions, the fabrication may be either as a composite unit or as individual members such as bottom beam, side walls, and roof slabs. The decision of the SA shall be final. |
| 6 | Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 Cement mortar 1:6 (1 cement : 6 coarse sand) Coarse sand : 12 graded stone aggregate 20 mm nominal size) upto plinth level with :Cement mortar 1:6 (1 cement : 6 coarse sand) Including cost of all materials, conveyance, loading and unloading, labour, hire charges, fuel, tools and plant, all applicable taxes, and incidental charges, complete as directed by the Engineer-in-Charge |
| 7 | Cement concrete flooring 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. Including cost of all materials, conveyance, loading and unloading, labour, hire charges, fuel, tools and plant, all applicable taxes, and incidental charges, complete as directed by the Engineer-in-Charge |
| 8 | Plastering with cement mortar 1:4 (1 cement :4 coarse sand) on brick/stone masonry or concrete surfaces, including surface preparation, raking of joints, cleaning and wetting, applying plaster to the specified thickness, finishing smooth and even, curing complete, including cost of materials, labour, scaffolding and all incidental charges, and directions of the Engineer-in-Charge. |
| 9 | Provision for neat Cement Punning on the RCC surface of ceiling and wall as directed by the departmental officers etc., complete complying with standard specifications |
| 10 | Painting two coats of newly plastered ceiling surface with White washing with lime to give an even shade Including cost of all materials, conveyance, loading and unloading, labour, hire charges, fuel, tools and plant, all applicable taxes, and incidental charges, complete as directed by the Engineer-in-Charge |
| 11 | Painting two coats of newly plastered wall surface with ready mixed plastic emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification |
| 12 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. |
| 13 | Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. Including cost of all materials, conveyance, loading and unloading, labour, hire charges, fuel, tools and plant, all applicable taxes, and incidental charges, complete as directed by the Engineer-in-Charge |
| 14 | Providing and laying integral cement based waterproofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc Including cost of all materials, conveyance, loading and unloading, labour, hire charges, fuel, tools and plant, all applicable taxes, and incidental charges, complete as directed by the Engineer-in-Charge |
| 15 | Providing and laying pressed clay tiles (as per approved pattern 20 mm nominal thickness of approved size) on roofs jointed with cement mortar 1:4 (1 cement : 4 coarse sand) mixed with 2% integral water proofing compound, laid over a bed of 20 mm thick cement mortar 1:4 (1cement : 4 coarse sand) and finished neat complete. Including cost of all materials, conveyance, loading and unloading, labour, hire charges, fuel, tools and plant, all applicable taxes, and incidental charges, complete as directed by the Engineer-in-Charge |
| 16 | Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge : 11.55.1 Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent. |
| 17 | Providing and fixing UPVC (Unplasticized Polyvinyl Chloride) louvered ventilators of approved make and quality, manufactured from multi-chambered UPVC profiles having minimum wall thickness of 2 mm, with outer frame size 60 mm × 58 mm and shutter profile size 60 mm × 78 mm, both profiles reinforced with 1 mm thick GI reinforcement with minimum 125 GSM zinc coating, fully corrosion-free. The ventilators shall be provided with EPDM rubber gaskets (black colour) all around the frame and shutter edges. The corners and joints of the profiles shall be fusion welded, properly cleaned and finished. The louvers shall be fitted with 4 mm thick radiation-free pin-headed glass securely fixed in position. The ventilator shall be fixed to the wall opening with proper alignment, 100% packing, screws and silicone sealant all around the frame to ensure a firm and watertight installation. All materials shall be of approved make and the ventilator shall be got approved by the Executive Engineer before use on work, complete in all respects including cost of materials, labour, fittings, conveyance and installation, |
| 18 | Providing and fixing 35 mm thick factory-made pre-laminated ABS (Acrylonitrile Butadiene Styrene) door shutters of approved make and design, moulded in different patterns, complete with all fittings and accessories. The door shutter shall consist of an all-round frame made of waterproof solid foam PVC bars of size 20 mm × 32 mm, reinforced with 32 mm × 32 mm LVL (Laminated Veneer Lumber) vertical members (2 Nos.). The core shall be of 32 mm thick high-density craft paper honeycomb board, sandwiched on both sides with 1.5 mm thick pre-laminated ABS sheets, and finished with 0.45 mm thick PVC edge banding on the vertical sides. The shutter shall be provided with steel-coated butterfly hinges (3 Nos. per shutter) and ISI-marked stainless steel round lock, complete. The rate shall include cost of materials, labour, fittings, conveyance, installation and finishing, complete in all respects and complying with standard specifications. The door shutter and frame shall be got approved by the Engineer incharge before use on work Including cost of all materials, conveyance, loading and unloading, labour, hire charges, fuel, tools and plant, all applicable taxes, and incidental charges, complete as directed by the Engineer-in-Charge |
| 19 | Providing and fixing UPVC / solid PVC door shutters or partition walls with jambs, complete with all fittings and accessories, as per approved specifications and directions of the Engineer-in-Charge. The shutter and frame shall be fabricated using 19 gauge, 19 mm MS square tubes for styles and outer frames, and 15 mm MS square tubes for top rail, lock rail and bottom rail. The steel members shall be fully covered with 5 mm thick solid PVC sheets. The shutter panelling shall be made of 5 mm thick solid PVC sheets, rigidly fixed in position. The overall size of styles shall be 50 mm × 30 mm, the overall size of top rail, lock rail and bottom rail shall be 75 mm × 30 mm, and the overall size of frames shall be 50 mm × 45 mm, provided with suitable rebate for housing the shutter. The work shall include supplying and fixing of all necessary furniture and fittings, complete. All materials shall be of approved make and quality, and the shutter, partition and frame shall be got approved by the Engineer in charge before use on work, complete in all respects including cost of materials, labour, fittings, conveyance and installation, |
