|
| 1 | Removing the existing aluminium/wooden partition for executing the floor repair works and handing over to sectional storewithout any damages. All complete as per specifications and as directed by the Engineer-in-charge |
| 2 | Removing the existing furniture like tables, chairsand storewells etc., from the room and stacking them separately to the nearby location & rearranging the same after completion of the floor repair works with man power. All complete as per specifications and as directed by the Engineer-in-charge |
| 3 | Removal of existing door shutter, window shutters of area 3 sq. metres and below (steel or wood) including stacking them separately to the nearby location/ in store.All complete as per specifications and as directed by the Engineer-in-charge |
| 4 | Providing and fixing ISI marked 35 mm thickflush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters, providing vision panel of Rectangular or square not exceeding 0.1 sqm in all type of flush doors and all necessaryfittings and fixturessuch as,ISI marked stainless steel butt hinges with necessary screws, stainless steel aldrop-1 no of 250 x 16 mm, bright finished brass tower bolts 150 x 10 mm (barrel type) with necessary screws 1 No, bright finished brass handles 125 x 10 mm 2 Nos with screws, two coats of synthetic enamel paint over a coat of wood primeron door frames etc, all complete as per specifications and as directed by the Engineer. |
| 5 | Providing and laying Fly Ash brick masonrywork with non modular bricks of size 230mm x 110mm x 75mm, fly ash lime bricks (FALG Bricks) conforming to IS:12894, having crushing strength not less than 10N/mm2 in CM 1:6 (1 cement : 6 coarse sand)at all heightsincluding curing, scaffolding wherever required etc., complete all as per specifications and as directed by the Engineer in Charge. |
| 6 | Providing and laying in position specified grade of reinforced cement concrete,1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size). make ofACC/ULTRATECH/BIRLA/JAYPEE cement grade of OPC-43, including pumping of concrete, laying at site,spreading and compacting mechanically by using needle and surface vibrator, curing by hassien cloth, carriage for all leads; the cost of centering, shuttering andfinishing but excluding reinforcement as per direction of the engineer-in-charge. The cement consumption for this item is 400Kg/Cum |
| 7 | Providing, laying and fixing in position TMT reinforcement bars of TATA/VIZAG STEEL/SAIL/JINDAL for RCC works, including cost of supplying, cutting, bending, transporting, erecting, binding with 16 gauge MS annealed wire, cement mortar spacer blocks etc. complete as per specifications and as directed by the Engineer in charge. |
| 8 | Providing and laying 15mm thick cement plaster in cement mortar 1:6 (1 cement :6 coarse sand) proportion over brick/ RR masonry/ Concrete walls, floors and other surfaces including providing and mixing approved water proof compound for external plaster in the proportion recommended by the manufacturer, raking of joints, hacking the concrete surfaces, scaffolding where necessary, curing etc., all complete as perdrawings, specifications and as directed by the Engineer in Charge. |
| 9 | Providing and laying Glazed Vitrified Matt/antiskid vitrified floor tiles of size 600mm x 600 mm of approved shade and make (viz. Johnson, Bell, Somany or equivalent which should be approved by department) (thickness to be specified by the manufacturer)with water absorption less than 0.08% andconformingtoIS:15622with ISI Mark, inallcoloursand shades, laidon 3mm thick high polymer modified quick-set tile adhesive (Water based)by using tile spacerfor uniform thickness of joints and levelling the undulations in floor (greater than 3mm thick) with cement mortar 1:4 (1 cement: 4coarse sand) as may be required including Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge. etc., including preparation of old flooring surface by manual/mechanical means by removal of old pvc flooring, hacking, pitting, grindingas directed, including removal of doors, trimming of bottom as required and refixing the same in position wherever required due to raise in floorlevel, cleaning etc., all complete as per specifications and as directed by the Engineer inCharge. |
| 10 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth all complete as per specifications and as directed by the Engineer-in-charge. |
| 11 | Providing and applying Two or more coats of 1st quality Acrylic distemper (internal walls) with dry distemper of approved brand Asian, Berger etc and manufacture of required shade on new work, over and including water thinnable priming coat to give an even shade including surface preparation, filling up of the holes and cracks with approved filling materials, scaffolding, cleaning, arranging safety appliances, insurance coverage to workers,all complete as per specifications and as directed by the Engineer-in-charge. |
| 12 | Providing and fixing tile false ceiling of approved materails with new grid using 6mm thick Cement bonded designer particle board/ Fiber Cement board like Bison designer Board/ \"V\" Board with texture on oneface of approved pattern conforming to IS 14276-1995/ IS 14862-2000 of size 595mm x 595mm finished with one coat of cement primer on both sides and edges including two coats of exterior emulsion paint of approved quality on exposed face & edges (thickness), interlocking metal grid of hot dipped galvanized steel sections (sleek groove grid system) (galvanized @120grams per sqm, both side inclusive) consisting of main \"T\" runner with suitably spaced joints to get required length and size 24 x 38mm made from 0.3mm thick (minimum) sheet, spaced at 1200mm center center and cross \"T\" of size 24 x 25mm made of 0.30mm thick (minimum) sheet, 1200mm long spaced between main \"T\" at 600mm center to center to form a grid of 1200 x 600mm and secondary cross \"T\"of length 600mmand size 24 x 25mm made of 0.30mm thick (minimum) sheet to be interlocked at middle of the 1200 x 600mm panel to form grids of 600 x 600mm and wall angle of size 24 x 24 x 0.30mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making opening for services likediffusers,grills,light fittings,fixtures, smoke detectors with the concern of Electrical/Instrumentation etc., with alround frame work, Main \"T\" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x 1.6mm fixed to ceiling with 8mm dia abd 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanized butterfly level clips of size 85 x 30 x 0.80mm spaced at 1200mm center to center along main \"T\", bottom exposed width of 2400 of all T-Sections shall be pre painted with polyster paint, lock pins, as per the approved pattern and to the extent required, scaffolding etc., all complete for all heights as per specifications, drawings and as directed by the Engineer in Charge. |
| 13 | Repair of window, modify the window AC Opening area as window by providing MS. Rodgrill by welding and float glass fixing and making good the same with existing window structure. Removal of dirt lumps, dust, other substances sticked to the window frame, removal of tree/vegetation in & outside the window and making good the same including providing missing window handles and applying two coats of synthtic enamel paintetc., all complete as per specificationandas directed by the Engineer in Charge. |
| 14 | Providing and fixing brass curtain rods of 20 mm diameter, wall thickness 1.25 mm with two brass brackets fixed with brass screws and wooden plugs including removal of old curtain brackets etc. wherever necessary, all complete as per specificationandas directed by the Engineer in Charge. |
| 15 | Providing and fixing 150 mm bright finished floor brass door stopper with rubber cushion, necessary brass screws etc. to suit shutter thickness, all complete as per specificationandas directed by the Engineer in Charge. |
| 16 | Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. all complete as per specificationandas directed by the Engineer in Charge. |
| 17 | Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors including door locking arrangements, windows with three shutters, three tiers for the moving shutters in window frame having middle frame with stainless steel mesh, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fastenersto be paid for separately) : Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 18 | Providing and fixing Frosted glassof nominal thickness 5 mm (weighing not less than 12.50 kg/sqm) in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge (Cost of aluminium snap beading shall be paid in basic item). |
| 19 | Providing and fixing 12 mm thick prelaminated particle boardwith decorative lamination on one side and balancing lamination on other sideflat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge. |
| 20 | Renewing Float glass panes with putty and nails/ Glazing clips wherever necessary at all heights with necessary scaffolding arrangements including racking out the old putty, removing & disposing of broken glass pieces, arranging safety appliances etc., all complete as per specificationandas directed by the Engineer in Charge. Note : Float glass panes of thickness 4.0mm (weightnot less than 10kg/sqm) |
| 21 | Providing and fixing sun control film of make Garware or approved make, quality and design complete as per specifications and directed by Engineer In Charge |
| 22 | Supply and fixing of elegance Tables and Chairs for conference seating & desking purpose from reputed brad like Godrej/IKEA/Wipro Furniture. The conference table to be fixed in U or V - Shape, all complete as per specificationandas directed by the Engineer in Charge. |
| 23 | Elegance MEM AV_2 STR Main TA X 1 having Table size 1350 mm X 710 mm X 740 mm or equivalent. |
| 24 | Elegance MEM AV_2 STR Shared TA X 2 having Table size 1350 mm X 710 mm X 740 mm or equivalent. |
| 25 | Elegance MEM AV_2 STR Shared TA X 2 having Table size 675 mm X 710 mm X 740 mm or equivalent. |
| 26 | Elegance MEM AV_1 STR End Left Hand side TA X 1 having Table size 1350 mm X 710 mm X 740 mm or equivalent. |
| 27 | ELEGANCE MEM AV_2 STR END_Right Hand Side TA X 1 having Table size1350 mm x 710 mm x 740 mmor equivalent. |
| 28 | High Back Chair of Pure Leather, Active Bio- Synchro with 5 Position Tilt Limiter, Die cast polished Aluminum Pedestal, Adjustable Arms, Back Height Adjustable, Seat Slide Mechanisam. |
| 29 | Thrill Mesh full Back Chair of Mesh Back, 1D Adjustable Arm rests, Centre Tilt Synchro Mechanism, 3 Pos Lock, Nylon Pedestal. |
| 30 | Supply of Stainless steel finish cylindrical lock of Make Godrej or equivalent, lock size 165mm x 50mm x 65mm suitable for door with thickness of 32-45 mm, a push button from inside and emergency opening from outside, automatic deadlocking, all complete as per specificationandas directed by the Engineer in Charge.Note : 3 Keys to be provided for each lock. |
