|
| 1 | Demolition cement concrete (unreinforcement) in ground floor and paving n exc 15 cm thickness (below or above ground level) & removal complete all rubbish materials complete all as specified and directed. |
| 2 | Demolition of brick work built in cement mortar complete all as specified and directed. |
| 3 | M&L for brick work with old size flyash bricks, straight or curved on plan exc 6 mean radius, built in CM 1:6 complete all as specified and directed. |
| 4 | M & L for Providing cement concrete type B1, 1:2:4 (20 mm graded aggregate) as in copings complete all as specified and directed. |
| 5 | S&F Mild steel Framed work such as grills, gratings, etc using angle Iron, flat Iron, round bars with end of bars shouldered and or rivetted or forged into spikes, framed guard barsbarred into iron doors, walkways railing framework amd similler work confiming to Fe 290 ,GDE E-165 complete all as specified and directed. |
| 6 | Framed work as in doors or gates of angle or other sectionwith gusset plates, rails,braces, etc., complete, drilled for fixing of steel sheeting or othercovering. Doors, etc. to be prepared for hanging or slidingwith and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete Fe 410-W (Gde-E- 250) quality-A complete all as specified and directed. |
| 7 | Taking down cement or cement lime plaster, of any description on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water complete all as specified and directed. |
| 8 | M&L for rendering 15mm thick in CM (1:4) on stone masonry surfaces or surfaces other than fair face of brick work as on wall surfaces and finish the surface even and fair. Using Water proofing compound @ 3% by weight of cement (WPC shall be measured and paid separately) complete all as specified and directed. |
| 9 | M&L rendering 10mm thick in cement mortar 1:6 on fair faces of brick/stone masonry or concrete surfaces of walls, finished even & smooth without using extra cement complete all as specified and directed. |
| 10 | M&L rendering 5mm thick in cement mortar 1:3 on concrete surfaces in ceiling, finished even & smooth without using extra cement complete all as specified and directed. |
| 11 | M&L for preparation of new plastered surfaces of walls and applying two coats of Oil bounddistemper overa coat of 1 mm thick wall care putty of approved tint complete all as specified & directed. |
| 12 | M&L preparation of newly plastered/unplastered surfaces of ceilings & applying three coats of white wash complete all as specified and directed. |
| 13 | M&L for complete removing of existing treatment including cleaning of mortar drops, smoke soot, moulds, moss, efflorescent salt, trading oil greasy spots etc on old decorated surfaces of wall and applying two coats of oil bound distemper of approved shade/tint over a coat of primer over and inclucluding 1 mm thick Birla white wall care putty complete all as specified and as directed. |
| 14 | M&L for preparation of old plastered surfaces of walls and applying one coat of white wash complete all as specified and directed. |
| 15 | M&L for preparation of newplastered surface and applying two coats of acrylic emulsion paint (exterior grade)of approved shade/tint over a coat of primer complete all as specified and as directed. |
| 16 | M&L for preparation of old plastered surface and applying two coats of acrylic emulsion paint (exterior grade)of approved shade/tint over a coat of primer complete all as specified and as directed. |
| 17 | Excavating in post holes (or similar) each n. exc 0.5 cum getting out returning filling in and ramming earth or broken rubble mixed with earth around in layers not exceeding 25 cm as in soft/loose soil complete all as specified and directed. |
| 18 | M&L cement concrete type C-2, 1:3:6 ( 40 mm graded aggregate) in foundation filling mass concrete for post holes etc complete all as specified and directed. |
| 19 | Dismantling Fencing of wire mesh Any type complete all as specified and directed. |
| 20 | Dismantling posts,purlins, or any part of truss, struts (wood, steel or R.C.C.) any section, including taking out embedded portion and making good disturbed ground or wall complete all as specified and directed. |
| 21 | S&F mild steelposts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed. |
| 22 | S&F mild steel bolt purpose made with hexagonal or square head one end screwedthe other end or screwed both ends each screwed to be fuitte3d with washer and one hexagonal or square nuts exceeding 50mm and n exc 75 mm long dia of the shank 16 mm complete all as specified and directed. |
| 23 | Fixing only chain link fencing including line wire any meshsize and type to any type of standards rails, straining bolts etc inlcluding provision of binding wire complete all as specified and directed. |
| 24 | Supply only chain link MS galvanised fencing any size or type weight n exc 4.00 Kg complete all as specified and directed. |
| 25 | S&F mild steel MS round bar 10 mm dia and over cut to length bent to shape required including cranking bending hooking etc and binding with MS wire 0.9 mm dia (annealed) complete all as specified and directed. |
| 26 | M&L for Galvanised 2 strand, steel barbedwire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails strain- ing bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed including taking down old wire complete all as specified and directed. |
| 27 | M&L preparation to new or previously untreated steel surface of any description,over 10cm in width or girth and applying two coats of synthetic enamel paint over a coat of zinc chromate primer complete all as specified and directed. |
| 28 | M&L prepration of New Surfaces of any description, n.exc 10cm in width or girth and applying two coats of synthetic enamel paintwhen unconnected with other painting or when painted in a different tint over a coat of zinc chromate primer complete all as specified and directed. |
| 29 | M&L cement concrete 75mm thick 1:4:8 type D-2 using 40mm graded aggregate as in sub base of floors complete all as specified and directed. |
| 30 | M&L for interlocking tiles 60 mm thick (M-35)having compressive strength not less than 35N/MM2 with grey cement and pigment complete all as specified and directed. |
| 31 | Sand filling under floors or in foundations including watering and consolidation complete all as specified and directed. |
| 32 | M&L precast kerb stone built in PCC TypeB1 1:2:4 using 20mm graded stone aggregate and fixing in CM 1:4 complete all as specified and directed. |
| 33 | Dismantling of old APP membrane from roof surface and cleaning surface to receive roof padding complete all as specified and directed . |
| 34 | M&L for PCC 1:2:4 type B0 (using 12.5 mm graded crushed stone aggregate) as in roof padding,laid to a minimum consolidated thickness of 25 mm as leveling course, laid and compacted inmin slope 1:30 over roof complete all as specified& directed by Engr-in-Charge. |
| 35 | M&L screed laid 15mm thick in CM 1:4with water proofing compound over green concrete surface(WPC will be measured and paid seperately) surface finished even and smooth (without using extra lime or cement) complete all as specified & directed by Engr-in-Charge. |
| 36 | S&F APP based polymeric membrane not less than 3mm thick, weighing not less than 3.5 Kg/sqm , reinforced with polyster non-woven fabric (weighing not less than 150 gm/sqm . It shall be laid by torch application,side overlaps shall be 75mm and the ends shall be 100mm and all over laps shall be sealed by torch application including applying a coat of cold applied bitumen primer conforming IS:[email protected]/sqm including applying two coats of aluminium paint over APP membrane surface complete all as specified and directed. |
| 37 | S&F Sheet glass, ordinary quality, in squaresexc 0.5 sq. m each pane 5.5 mm in thickness complete all as specified & directed by Engr-in-Charge. |
| 38 | S&F in repairs 600mm x 450 mmlooking mirror bevelled edge mirror 5.5 mm thickof selected qualityglss mounted on 6 mm thick ply and fixed to wall with wooden plugs chromium plated brass screws and washers complete all as specified and directed. |
| 39 | M&L for Rough cast plaster on exterior walls applying the under coat of cement and sand mortar 1:3 not less than 10mm thick and while it is still in plastic state the roughcast mixture consisting of crushed stone or fine gravel aggregate (size between 6 to 12mm) mixed with coarse sand and cement in the ratio of 1:1:1 shall be applied and finished even .The mix of cement and sand shall made slightly wetter than normal for rendering to ensure that larger aggregate are thoroughly covered complete all as specified and directed by Engineer in Charge. |
| 40 | S&F anodized aluminium frame and other sections for doors, windows, ventilators, partitions, powder coated of any colour as approved (Thickness or powder coating not less than 50 micron) with one or more rebates including joining cleat for fixing etc complete all as specified and directed. |
| 41 | S&F anodized aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m, powder coated of any colour as approved (Thickness or powder coating not less than 50 micron) including necessary joining cleats, glazing clips, rubber packing, anodized aluminium snap beading, screws, anodized aluminium fittings such as peg stays 150mm long (1 No.), hinges type B-21 100mm long (2 Nos), suitable handle (1 No.) complete all as specified and directed. |
| 42 | S&F anodized aluminium door shutters, aluminium section weighing 0.55 kg/m, powder coated of any colour as approved (Thickness or powder coating not less than 50 micron) including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodized aluminum snap beading screws etc complete all as specified and directed. |
| 43 | S&F forpowder coated of any colour as approved anodised aluminium grill of approved pattern for windows/ ventilators/doors complete all as specified and directed. |
| 44 | S&F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed. |
| 45 | S&F in repairs vitreous china wash down water closet pan (Pedestal pattern EWC), coloured, floor mounted coupled closet, including connection to drain (or outgoing pipe), anti-sypohonage pipe etc, with & including WC seat cover coloured closed pattern with flat bottom and cover, CP jet nozzle, vitreous china symphonic action type twin flush flushing cistern of 10 litre capacity with lid, necessary fittings complete all as specified & as directed. |
| 46 | S&F in repairs Pillar tap fancy type , cast copper alloy with capstan heads, chromium plated, screwed down high pressure with or withoutlettered \"Hot\" or \"Cold\" with long screwed shanks & fly nuts, screwed for iron pipes of 15mm bore complete all as specified and directed. |
| 47 | S&F in repair towel railsof 20mm dia tubular brass chromium plated 60cm long \"D\" type fixed to complete all as specified and directed. |
| 48 | Taking up or down 15mm steel tubing and connections, complete all as specified and directed. |
| 49 | S&F steel tubing medium grade 15mm bore with all fittings fixed complete to wall and or laid in floor complete all as specified and directed. |
| 50 | M&L for 20mm thick Granite slab of approved shade, as in platform etc, bedded & jointed with grey cement slurry and pointed with white cement with admixture of pigment to match with shade of Granite stone including cutting, grinding and polishing (mirror polish i.e. full granite polish as per local trade practice) including required cutting to suit the size of oval type wash hand basin over & including 15mm thick screed bed in cement & sand mortar 1:6 complete all as specified and as directed. |
| 51 | M&L 75 mm thick PCC(1:3:6) type C2 (using 40mm graded stone aggregate ) as in plinth protection finished even and smooth without using extra cement complete all as specified and directed. |
| 52 | Taking down Chowkats or frames with shutters (without taking off shutters from the frame) n exc 1.5 sq.each & removing to store complete all as specified and directed. |
| 53 | Taking down Chowkats or frameswith shutters ( without taking off shutters from the frame exc 1.5 sq. m but n exc 4 sq m each & removing to store complete all as specified and directed. |
| 54 | M&L Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing. |
| 55 | M&L Factory made solid panel pvc door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC `C\" channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site complete all as specified and directed. |
| 56 | S&F Butt hinges 100mm long medium weight, colled rolled mild steel complete all as specified and directed. |
| 57 | S&F 150mm Aluminium, anodised, barrel tower bolts of extruded section and fixedcomplete all as specified & directed |
| 58 | S&F 150mm Aluminium handles, cast type, anodised complete all as specified & directed |
| 59 | Dismantling floor, hearth or wall tilling including cement mortar bedding (but not backing) removing serviceable tiles to stores and rubbish off premises complete all as specified and directed. |
| 60 | M&L Non skid white Ceramic tiles7 to 8 mm thick in light shade(square/rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and incl 15 mm thick cement screed in cm 1:6 complete all as specified and directed. |
| 61 | M&L Glazed ceramic coloured tiles in vertical surface450X 300X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the shade of the tiles and over 10 mm thick rendring in cm 1:4 complete all as specified & directed |
| 62 | M&L Non skidCeramic tiles 7 to 8 mm thick in light shade(square/rectangular) polished, area of each tiles exceeding0.18 sqm but not exceeding 0.36 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and incl 15 mm thick cement screed in cm 1:6complete all as specified and directed. |
