|
| 1 | Boring, providing and installing bored cast-in-situ reinforced cement concrete piles of grade M-25 of specified diameter andlength below the pile cap, to carry a safe working load not lessthan specified, excluding the cost of steel reinforcement but including the cost of boring , with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc, by percussion drilling using direct mud circulation (DMC) or bailer and chisel technique by tripod and mechanical winch machine all complete, including removal of excavated earth with all its lifts and leads (length of pile for payment shall be measured upto bottom of pile cap) - 450 mm dia piles - Note: Truck Mounted rotary/TMR/Tubewell boring machine shall not be used |
| 2 | Reinforced cement concrete work in walls(any thickness) , including attached pilasters, buttresses , plinth and sting courses , fillets , columns , pillars , piers , abutments , posts and struts etc. upto floor five level excluding cost of centering , shuttering , finishing andreinforcement - 1:1.5:3 (1 cement : 1.5 fine aggregate : 3 graded stone aggregate 20mm nominal size) |
| 3 | Reinforced cement concrete work in beams,suspended floors, roofs having slope up to 15degree landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto floor five level excluing the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 fine aggregate : 3 graded stone aggregate 20mm nominal size) |
| 4 | Centering and shuttering including strutting , propping etc andremoval of form for - Suspended floors , roofs , landings ,balconies and access platform |
| 5 | Centering and shuttering including strutting , propping etc andremoval of form for - Lintels , beams , plinth beams , girders ,bressumers and catilevers |
| 6 | Centering and shuttering including strutting , propping etc andremoval of form for - Columns , Pillars , Piers , Abutments , Posts and Struts |
| 7 | Steel reinforcement for R.C.C.work including straightening ,cutting , bending , placing in position and binding all complete upto plinth level - Thermo -Mechanically treated bars Fe - 500D or more |
| 8 | Earthwork in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as per direction of Engineer-in-charge, within a lead of 50m - all kinds of soil |
| 9 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering.- All work upto plinth level -1:5:10 (1cement:5 fineaggregate:10graded stone aggregate 40mm nominal size) |
| 10 | Brick work with common burnt clay F.P.S (non modular )bricks of class designation 3.5 in superstructure above plinth level upto floor five level in all shapes and sizes in - cement mortar 1:4 ( 1 cement : 4 fine aggregate) |
| 11 | Brick work with common burnt clay F.P.S (non modular ) bricks of class designation 3.5 in foundation and plinth in - cement mortar 1:4 (1 cement : 4 fine aggregate) |
| 12 | Brick work 7 cm thick common burnt clay F.P.S. (non modular) brick of class designation 3.5 in cement mortar 1:3 (1cement : 3 fine aggregate) in superstructure above plinth level and upto floor five level |
| 13 | 12mm cement plaster of mix -1:4 ( 1 cement : 4 fine aggregate) |
| 14 | 15mm cement plaster on the rough side of single or half brick wall of mix - 1:6 (1cement : 6 fine aggregate) |
| 15 | Providing and fixing factory made uPVC door frame made ofuPVC extruded sections having an overall dimension as below (tolerance +_ 1mm ), with wall thickness 2.0 mm (+-0.2mm) , corners of the door frame to be jointed with galvanized brackets and stainless steel screws , joints mitred and plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S.tube of size 19 x 19 mm and 1mm (+-0.1mm)wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturer\"s specification and direction of Engineer-in-charge - Extruded section profile size 48 x 40 mm |
| 16 | Providing and fixing to existing door frames - 30 mm thick factory made Polyvinyl Chloride (PVC) door shutters made of styles and rails of a uPVC hollow section of size 60 x 30 mm and wall thickness 2 mm (+- 0.2 mm) with inbuilt decorative moulding edging on one side . The styles and rails mitred and joint at the corners by means of M.S. galvanised / plastic brackets of size 75 x 220 mm having wall thickness 1.0 mm and stainless steel screws . The styles of the shutter reinforced by inserting galvanised M.S.tube of size 25x20 mm and 1mm (+- 0.1mm) wall thickness . The lock rail made up of \"H\" section , a uPVC hollow section of size 100 x 30 mm and 2 mm (+-0.2 mm) wall thickness , fixed to the shutter styles by means of plastic / galvanised M.S. \"U\" cleats. The shutter frame filled with a uPVC multichambered single panel of size not less than 620 mm, having overall thickness of 20 mm and 1 mm (+_ 0.1mm) wall thickness . They panels filled vertcally and tie bar at two places by inserting horizontally 6 mm galvanised M.S.rod and fastened with nuts and washers , complete as per manufacturer\"s specification and direction of Engineer-in-charge |
| 17 | Providing and fixing M.S.grills of required pattern in frames of windows etc with M.S. flats , square or round bars etc.including priming coat with approved steel primer all complete - Fixed to openings / wooden frames with rawl plugsscrews etc |
| 18 | Providing and fixing of 65mm Navatal lock of 6 levers etc complete |
| 19 | Providing 40 X 5 mm flat iron hold fast 400 mmlong including fixing to frame with 10 mm diameter bots, nuts and wooden plugs and embeddings in cement concrete block 300 x100 x 150 mm 1:3:6 mix (1 cement : 3 fine aggregate : 6 graded stone aggregate 20mm nominal size) |
| 20 | Providing and fixing aluminium sliding door bolts , ISI marked , anodised ( anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade , withnuts and screws etc complete - 300 X 16 mm |
| 21 | Providing and fixing aluminium tower bolts , ISI marked ,anodised (anodic coating not less than grade AC 10 as per IS :1868) , transparent or dyed to required colour or shade , withnecessary screws etc. complete - 250 x10 mm |
| 22 | Providing and fixing aluminium tower bolts , ISI marked ,anodised (anodic coating not less than grade AC 10 as per IS :1868) , transparent or dyed to required colour or shade , withnecessary screws etc. complete - 100 x10 mm |
| 23 | Providing and fixing aluminium handles , ISI marked , anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade,with necessary screws etc, complete - 125 mm |
| 24 | Providing and fixing aluminium handles , ISI marked , anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade,with necessary screws etc, complete - 100 mm |
| 25 | Providing and fixing bright finished brass hard drawn hooks and eyes -150mm |
| 26 | Providing and fixing M.S. fan clamp type I or II of 16mm dia M.S. bar, bent to shape with hooked ends in R.C.C.slabs orbeams during laying , including painting the exposed portion of loop, all as per standard design complete |
| 27 | Cement concrete pavement with 1:2:4 (1 cement : 2 fine aggregate: 4 graded stone aggregate 20 mm nominal size)including finishing complete |
| 28 | Providing and fixing on wall face unplasticised rigid PVC rain water pipes conforming to IS: 13592 Type A, includingjointing with seal ring conforming to IS : 5382, leaving 10mmgap for thermal expansion, (i) Single socketed pipes - 110 mm diameter |
| 29 | Providing and fixing on wall face unplasticised - PVC moulded fittings / accessories for unplasticised rigid PVC rain water pipes conforming to IS:13592Type A, including jointing with seal ring conforming to IS: 5382, leaving 10mm gap for thermal expansion - bend 87.5degree - 110 mm bend |
| 30 | Providing and fixing on wall face unplasticised - PVC moulded fittings / accessories for unplasticised rigid PVC rain water pipes conforming to IS:13592 Type A, including jointing with seal ring conforming to IS:5382, leaving 10mm gap for thermal expansion - shoe (plain) - 110mm shoe |
| 31 | Providing and fixing unplasticised - PVC pipe clips ofapproved design to unplasticised- PVC rain water pipes bymeans of 50x50x50mm hard wood plugs , screwed with M.S.screws of required length, including cutting brickwork and fixing in cement mortar 1:4 ( 1 cement : 4 fine aggregate) andmaking good the wall etc., complete - 110mm |
| 32 | Providing and fixing white vitreous china wash basin including making all connections but excluding the cost of fittings - flat back wash basin of size 550x400mm |
| 33 | Providing and fixing P.V.C. waste pipe for sink or wash basin including PVC waste fittings complete - flexible pipe - 32mmdia |
| 34 | Providing and fixing Chlorinated Polyvinnyl Chloride (CPVC)pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings includingfixing the pipe with clamps at 1.00m spacing.This includesjointing of pipes & fittings with one step CPVC solvent cementand testing of joints complete as per direction of Engineer-incharge - internal work - exposed on wall - 20 mm nominal dia pipes |
| 35 | Providing and fixing brass bib cock of approved quality - 15mm nominal bore |
| 36 | poviding and laying vitrified floor tiles of size 600 x600 mmthickeness to be specified by the manufacturer) with waterabsorption less than 0.08% and conforming to IS: 15622 ofapproved make , in all colours and shades, laid on 20 mm thickcement mortar 1:4 (1 cement : 4 fine aggregate) ,jointing with grey cement slurry @3.3 kg per sqm including grouting the joints with white cement and matching pigments etc., complete - size of tile600x600mm |
| 37 | Providing and laying rectified glazed ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer) of 1st quality conforming to IS:15622 of approved make in all colours, shades, except white, ivory, grey, fume red brown, laid on 20mm thick cement mortar 1:4 (1 cement : 4 fine aggregate) jointing with grey cement slurry @3.3 kg per sqm including pointing the joints with white cement and matching pigments etc., complete |
| 38 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS:15622(thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved, in skirting, risers of steps and dados, over 12mm thick bed ofcement mortar 1:3 (1 cement : 3 fine aggregate) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete |
| 39 | Painting with synthetic enamel paint of approved brand and manufacutre to give an even shade - Two or more coats on new work |
| 40 | White washing with lime to give an even shade - new work(three or more coats) |
| 41 | Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound) content less than 50 grams / litre, of approved brand and manufacturer, including applying additional coats wherever required, to achive even shade and colour - Two coats |
| 42 | Finishing walls with premium acrylic smooth exterior paint with silicone additives of required shade - New work (two or more coats applied @1.43 ltr / 10 sqm over and includingpriming coat of exterior primer applied @0.90 litre / 10sqm) |
| 43 | Supplying and laying of following size of PVC conduit in roof slab alongwith the accessories .Make:Avonplast/Vijaya:- 25mm dia |
| 44 | Supplying and fixing of following size of PVC conduit alongwith the accessories in surface/recess Conduit includingcutting the wall and making good the same in case of recessedconduit asequired. Make:Avonplast/Vijaya:- 20mm dia |
| 45 | Supplying and fixing of following size of PVC conduitalongwith the accessories in surface/recess Conduitincludingcutting the wall and making good the same in case of recessed conduit as required. Make:Avonplast/Vijaya:- 25mm dia |
| 46 | Supplying and fixing of following size of PVC junction box inrequired position along the line of PVC conduit as required.Make:Avonplast/Vijaya:- 25mm Junction Box two way |
| 47 | Supplying and fixing of following size of PVC junction box inrequired position along the line of PVC conduit as required.Make:Avonplast/Vijaya:- 25mm Junction Box two way |
| 48 | Supplying and drawing of 1.5 sqmm. FR PVC insulated, copper conductor, single core cable in the existingsurface/recessed, PVC/steel conduit/PVC casing and capping asrequired.Make: Finolex/Polycab:- |
| 49 | Supplying and drawing of 2.5 sqmm. FR PVC insulated,copper conductor, single core cable in the existingsurface/recessed, PVC/steel conduit/PVC casing and capping asrequired.Make: Finolex/Polycab:- |
| 50 | Supplying and drawing of 4.0 sqmm. FR PVC insulated,copper conductor, single core cable in the existingsurface/recessed, PVC/steel conduit/PVC casing and capping as required.Make: Finolex/Polycab:- |
| 51 | supplying and fixing S.P 1 way 5/6amps piano/flush type switch on the existing switch box/cover including connections etc. asrequired.Make:Kundan/Anchor/Vinay :- |
| 52 | Supplying and fixing S.P 1 way 15/16amps piano/flush typeswitch on the existing switch box/cover including connections etc. as required.Make:Kundan/Anchor/Vinay:- |
| 53 | Supplying and fixing 3 pin 5/6amps piano/flush type socket outlet on the existing switch box/cover including connections etc. as required.Make:Kundan/Anchor/Vinay:- |
| 54 | Supplying and fixing 3 pin 15/16amps piano/flush type socketoutlet on the existing switch box/cover including connectionsetc. as required.Make:Kundan/Anchor/Vinay:- |
| 55 | Supplying and fixing of the following sizes of Teak wooden board on recess including cutting the wall and finishing the surface good the same as required - 300mm X 250mm X50mm. Deep |
| 56 | Providing and fixing of following size phenolic coated sheet onexisting wooden board: - 300mm X 250mm X 3mm Thick |
| 57 | Supplying and fixing 3 plate, 5 amp.ceiling rose on the existingjunction box/wooden block including connections etc. as required.Make: Kundan/Anchor/Vinay:- |
| 58 | Supplying and fixing jumbo type Batten/Angle Holder includingconnections etc. as required .Make: Kundan/Anchor/Vinay:- |
| 59 | Supplying and fixing 40W incandescent bulb. Make: Philips/Bajaj |
| 60 | Supplying and fixing Bulk head fitting aluminium alloy body heat resistantprismatic glass cover with specially designed gasket(GLS 100W type). Make: Philips/Bajaj |
| 61 | Supplying and fixing 1200mm sweep double ball bearing ceiling fan.Make:Almonard/Usha |
| 62 | Supplying and fixing Step type socket Fan Regulator on the existing switch box/cover including connections etc. as required.Make:Kundan/Anchor/Vinay:- |
| 63 | Supplying and fixing 1 x 40W box type single tube light fitting with copperchoke & starter with tube. Make: Philips/Bajaj |
| 64 | Installation, testing and commissioning of prewired, all kind ofsurface mount light fittings, complete with all accessories etc. directly on ceiling/wall, including connections with 16/0.20 mm twin core FR PVC sheathed flat flexible, copper cable etc. as required. |
| 65 | Installation, testing and commissioning of prewired, all kind of recess mount light fittings, complete with all accessories etc. on false ceiling, including connections with 16/0.20 mm twin core FR PVC sheathed flat flexible, copper cable etc. as required. |
| 66 | Earthing with G.I.medium pipe 3.0 mt long and 40mm dia including accessories 250 x 50 x 6 mm G.I clamp with 12mmbolt, nut and washer for connecting earth wire, RCC ringenclosure and cover plate complete as required:- |
| 67 | Extra for salt and charcoal for pipe earth electrode as required:- |
