|
| 1 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth, 1.5m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth, lead up to 50m and lift up to 1.5m,as directed by Engineer-in-Charge., All kinds of soil |
| 2 | Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement, All works upto plinth level, Concrete of M30 grade with minimum cement content of 350 kg /cum |
| 3 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :, 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources). |
| 4 | Centering and shuttering including strutting, propping etc. and removal of form for :, Foundations, footings, bases of columns, etc. for mass concrete |
| 5 | Mild steel or iron work in plain work such as in R.C.C. or R.B. (when not included in an over all rates ) including bending for proper completion of the work and including supply of steel and its wastage , bends, hooks and authorised overlaps shall be measured up to floor two level. (SI No. 504) (Sanction Rate) |
| 6 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete., Fixed to openings /wooden frames with rawl plugs screws etc. |
| 7 | \"Providing & fixing of Dustbin made in mild steel frame with painting & polish and frame wooden member fixed in m.s. frame including painting polishing as per drawing & design all complete in direction of engineer in charge. PSR |
| 8 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete., Hot finished welded type tubes. |
| 9 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :, Cement mortar 1:6 (1 cement : 6 coarse sand) |
| 10 | Applying stamping finish to the top surface of freshly laid plain / reinforced cement concrete of specified grade in portico, side walks, drive ways, pool decks and open yard as per direction of the Engineer-in-Charge. * The concrete shall be placed and screened to the finished grade and floated to the uniform surface by using standard finishing techniques. approved color hardener @ 2.7 kg/sqm shall be applied evenly to the surface of the fresh concrete by the dry shake method by sprinkling in twoor more shakes floated after each shake and trowel only after final floating. The approved released agent @ 0.113 Kg/Sqm shall be applied evenly to the trowelled surface before stamping or the said release agent can be applied to the flexible polyurethene stamp moulds of approved design and in required sizes to achieve final stamping pattern. These stampings shall be placed on the surface of concrete in three to four pieces at a time and tapped gently with rammers of sufficient size and weight to leave proper stamp marks and the process repeated for the remaining concrete surface till the whole surface to be stamped is completed within the time while the concrete is in plastic stage of setting. * After stamping, the curing shall be done as per manufacturers specifications. After initial curing the imprinted joints shall be grouted using cement slurry mixed with color hardener as per the requirement. The surface shall be sealed by applying acrylic based sealer not less than 0.167 litre/Sqm on finished surface. * The construction joints shall be provided by grove cutting of size 4 mm x 20 mm in panel size 3 m x 3 m or lesser as per the site conditions and filling the same with 10 mm baker rod and providing & laying (PU) Polyurethane based joint sealer of approved make as per manufacturer’s specifications and finished by applying polyurethene resin based topprotective clear coat of minimum 80 micron applied with rollers on properly cured and dry clean surface. (The cost of concrete for flooring is not included in the item, which shall be paid for seperately). |
| 11 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 12 | Finishing walls with Acrylic Smooth exterior paint of required shade :, New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm) |
| 13 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade:, Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade: Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture. |
| 14 | S/E of G.I. wire on 8 to 4 SWG on pole/service bracket including binding etc. complete in all respects SI.No. 628/18. PWD E/I 2018 |
| 15 | S/W of submain with two Nos. of 2.5 Sq.mm FRLSH PVC insulated 1100 V grade single core multistrand copper conductor cable in existing conduit complete with supply of all material Labour and T&P required for proper completion of the work as directed at site by E/I. SI. No. 289/18. |
| 16 | Supply and fixing following capacity of automatic street light cubicle control panel painted with anti corrosive alkali and acid proof paint consisting of time switch TSO 100 series with contactors, HRC fuses, isolating switch metering instrument & instrument box with CTs etc. in case of TPN, complete in all respect 40 A TPN PWD 807 |
| 17 | 1454 PWD E&M 2018 Supply and fixing of factory wired integral LED flood light luminaires with die cast aluminium housing built with dirver set suitable for 140 to 150 Watt. Confirming to IP 66 protection complete in all respect. CAT-AA |
| 18 | Supply and laying of aluminium conductor PVC insulated armoured served sheathed cables 1100 Volts grade at a depth of 750 mm below ground level over a cushion of 75 mm. thick sand all around and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on M.S clamps etc. of suitable size or as directed by the Engineer-Incharge complete in all respect. The armouring of the cable shall be properly connected with the earth conductor by clamps etc. PWD 501 25.00 Sqmm 3.5 Core |
| 19 | Supply and laying of aluminium conductor PVC insulated armoured served sheathed cables 1100 Volts grade at a depth of 750 mm below ground level over a cushion of 75 mm. thick sand all around and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on M.S clamps etc. of suitable size or as directed by the Engineer-Incharge complete in all respect. The armouring of the cable shall be properly connected with the earth conductor by clamps etc. PWD 501 70.00 Sqmm 3.5 Core |
| 20 | Supply, Installation, Testing and Commissioning of 15 W LED Bollard Light with mounting base accessories having LED operating life >50000 burning hours, Input Voltage range of 160V-260V, LED chip make Cree, Citizen, Osram, Nichia. Working temperature -10deg - 60 deg C, colour temprature should be 3000K/4000K/6000K, Good Thermal management System with inbuilt drivers. Corrosion resistant aluminum cast housing and Ingress Protection IP66. Size of the shall be Square 150mm x 150mm x 600mm Height complete in all respect as directed by Engineer-in-charge.. |
| 21 | S/L of following cable \"Al\" conductor P.V.C. insulated armoured served sheathed cable 1100V grade at a depth of 750mm. Below ground level over a cushion of 75mm with DWC Pipe approved make UPPPCL as per direction of E/I. complete in all respects. 501/2018. Approved Makes:- Gloster/ Polycab/ KEI/ SCI/ Havells |
| 22 | \"Supply and erection of factory fabricated and wired metal clad dust and vermin proof floor mounting panel TPN switch board complete with the following HRC type heavy duty TPN fuse switches with fuses and instrument chamber etc. complete in all respects. The instrument chamber shall be separate and shall comprise of flush type ammeter, voltmerer, selector switches for ammeter and voltmeter, instrument fuses, current transormer etc. The board shall have suitable capacity electroytic alumininum busbars as per IS8623 istulate with heat shrink sleeving and mountend on non hygroscopic supports such as CMC/DMC support with deteachable side covers and shall be suitable for extension on the sides. The switches shall be complete with suitable cable end boxes, reverse entery boxes in case of pedestaal type, cable sockets, compression glands and indicating lamp on incoming etc. The job includes the grounting of the board as per direction of Engineer-in-Charge. All coutgoing switches of 100 Amp. and above will be provided with ampere metre current transformers and selector switches and instrument fuses etc. The switches board shall be fabricated with CRCA sheet with a minimum thickness of 1.6 mm/2 mm. Cubicle type switch board shall be of cat A B & B-II and pedestal type for Cat-B and C only. ( Incoming 200 Amp. TPN-1 No Outgoing 100 Amp. TNP-2 Nos. Cat. B. Cubicle Type PWD SI No : 802 (a)\" |
| 23 | Supply and burring of Safe Earthing Electrode T-19 (Hot Dip Galvanized), Length up to 2000mm, outer pipe 50mm, inner pipe 25, terminal Dia 12 mm, outer GI pipe of 16 swg and inner GI pipe of 12 swg with Hot Dip Galvanization up to 100 micron filled with crystalline conductive mixture (CCM) having anti corrosive & conductive property with 50 kgs activated soil (BFC) capable of reducing the soil resistivity with good mixture of retaining capacity along with 30cm square C.I. frame with hinged cover & masonry husing (from electrode terminal to switch board, cost of 25 x 3 G.I . strip will be extra) Make: As approved in U.P. P.W.D., & C.P.R.I. Certified. PWD SI No :725 (A) |
| 24 | S/B of earth rod 20mm dia into 2.5mtr long including G.I. wire 7/16 SWG to connect earth rod to earth clamp on pole 3.00 mtr long steel conduit to carry earth wire along the pole. For singel support ANNEXURE 6 - SL NO. 17 |
| 25 | S/F of 6 Amp to 32 Amp. SPMCB (10KA) C curve complete in all respect as per direction of Engineer-in-charge. SI No. 1002/18. CAT-A. |
| 26 | Supply and Laying of 63 mm dia (OD-63 mm & ID-51 mm nominal) DWC HDPE Pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to 14930, Part II complete with fitting and cutting, jointing etc. direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc. complete as required. 33.01 (Jal Nigam Varanasi SOR) 63mm dia HDPE Pipe PN-6: ClassPE-100 |
| 27 | \"Providing & fixing sand stone Single piece ornamental bench of approved design pattern (1200x450x450MM) and specifications including , all materials, labour and T & P etc. required for proper completion of work as directed by engineer - in -charge PSR |
| 28 | Supplying and stacking of well decayed cattle manure at site including royalty and carriage upto 5 k.m.lead complete (Cattle manure measured in stacks will reduced by 8% for Payment). |
| 29 | Mixing earth and sludge or manure in the required proportion specified or directed by the Officer-in-charge |
| 30 | Spreading of sludge, dump manure and/or good earth in required thickness as per direction of officer-in-charge (cost of sludge, dump manure and/ or good earth to be paid separately). |
| 31 | Trenching in ordinary soil up to a depth of 60 cm including removal and stacking of serviceable materials and then disposing of surplus soil, by spreading and neatly levelling within a lead of 50 m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge or / and manure before and after flooding trench with water (excluding cost of imported earth, sludge or manure). |
| 32 | Rough dressing the trenched ground including breaking clods. |
| 33 | Fine dressing of the ground. |
| 34 | Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unserveiceable material’s as per direction of officer in charge (excluding cast of plant & water), Trees Plant |
| 35 | Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unserveiceable material’s as per direction of officer in charge (excluding cast of plant & water), Hedge Plant /Ground cover |
| 36 | Providing and stacking of Murraya exotica of height 45-60 cm. in poly bags of size 15 cm as per direction of the officer-in-charge. |
| 37 | Providing and Displaying Acalypha red well developed with fresh & healthy 30 to 45 cm ht. in 20 cm size Earthen Pot/ Plastic Pot as per direction of the officer-in-charge. |
| 38 | Providing and stacking of Ophiopogon jaburan ( variegated ),full of variegated leaves in Earthen Pot/Plastic Pot of size 20 cm. as per direction of the officer-in-charge. |
| 39 | Providing and stacking of Chandni dwarf of height 15-20 cm., well branched in earthen pots of size 20 cm as per direction of the officer-in-charge. s per direction of the officer-in-charge. |
| 40 | Providing and stacking of Syngonium variegated,of height 20-30 cm. with 2-3 suckers healthy foliage in Earthen Pot/Plastic Pot of size 15 cm. as per direction of the officer-in-charge. |
| 41 | Provding and stacking of jacaranda mimosifolia of height 10-12 feet in big poly bogs of size 18 as per direction of the office-in-charge sanctioned rate. |
| 42 | Providing and stacking of Delonix regia (Gulmohar) healthy and multi brances of height 12-14 feet in big poly bags of size 18\" as per direction of the officer-in-charge. |
| 43 | Providing and stacking of Butea frondosa (Flame of Forest) healthy and multi branches of height 4-6 feet in big poly bags of size 18\" as per direction of the officer-in-charge. |
| 44 | Providing and stacking of Peltophorum species healthy and multi branches of height 12-14 feet in big poly bags of size 18\" as per direction of the officer-in-charge. MR |
| 45 | Providing and stacking of Mahogany healthy & multi branches of height 12-14 feet in big poly bags of size 18\" as per direction of the officer-in-charge. |
| 46 | Providing and stacking of Cane of height 8 - 10 ft. .,bushy in big size 12\" HDPE bag as per direction of the officer-in-charge |
| 47 | Providing and stacking of DEODAR of height 8 - 10 ft. .,bushy in big size 12\" HDPE bag as per direction of the officer-in-charge |
| 48 | Providing and stacking of PINE of height 8 - 10 ft. .,bushy in big size 12\" HDPE bag as per direction of the officer-in-charge |
| 49 | Providing and stacking of Juniper of height 8 - 10 ft. .,bushy in big size 12\" HDPE bag as per direction of the officer-in-charge Providing and stacking of PINE of height 8 - 10 ft. . |
| 50 | Providing and stacking of Chinar of height 8 - 10 ft. .,bushy in big size 12\" HDPE bag as per direction of the officer-in-charge |
| 51 | Providing and stacking of Eugenia jambolana (Jamun) different variety of height 18\" in big poly bags of size as per direction of the officer-in-charge. |
| 52 | Providing and stacking of Magnolia grandiflora of height 150-165 cm. in big poly bag of size 25 cm as per direction of the officer-in-charge.v |
| 53 | Providing and Displaying Bamboo Buddha Valley with fresh & healthy 5 to 6 suckers 1.80 m to 2.10m ht umbrella type well developed in 50 cm Cement Pot as per direction of the officer-in-charge. |
| 54 | Words with frames and fixed in ms painting and Acrlylic 20 mm sheet. Backlit and each letter with a size of 2x2 ft. |
| 55 | Supply and installation of Deck wood, Ipe/Pine of random length but 140 mm wide and 25-26 mm thick planks finished and good for outdoors |
| 56 | Making, Supply and fixing of sculpture made of fibre casting/stainless steel of height 8 ft. Theme animal and Bird of the Forest Approved Rates. Please Enable Macros to View BoQ information |
