|
| 1 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. |
| 2 | a) All kinds of soil. |
| 3 | Providingandlayinginpositioncementconcreteof specified grade excluding the cost of centering and shuttering - All work up to plinth level : |
| 4 | 1:2:4 (1cement : 2 coarse sand (zone-Ill) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 5 | 1:3:6 (1Cement : 3 coarse sand (zone-Ill) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 6 | 1:4:8 (1Cement : 4 coarse sand (zone-Ill) derived from natural sources: 8 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 7 | Makingplinthprotection 50mmthickofcementconcrete 1:3:6 (1cement : 3 coarse sand (zone-Ill) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75 mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. |
| 8 | Providing and laying in position specified grade of reinforced cement concrete,excludingthecostofcentering,shuttering,finishingand reinforcement - All work up to plinth level : |
| 9 | 1:1.5:3(1 cement: 1.5 coarse sand (zone-Ill) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 10 | Reinforced cement concrete work in walls (any thickness),including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor fivelevel,excludingcost of centering,shuttering, finishingand reinforcement: |
| 11 | 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 12 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15 degree landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). |
| 13 | Centering and shuttering including strutting, propping etc. and removal of form for |
| 14 | Foundations,footings,basesof columns,etc.formass concrete |
| 15 | Walls (anythickness)includingattachedpilasters, butteresses, plinth and string courses etc. |
| 16 | Suspended floors,roofs,landings,balconies and access platform |
| 17 | Shelves (Cast in situ) |
| 18 | Lintels,beams,plinthbeams,girders,bressumersand cantilevers |
| 19 | Columns, Pillars, Piers, Abutments, Posts and Struts |
| 20 | Steelreinforcement forR.C.C.workincludingstraightening,cutting, bending, placing in position and binding all complete upto plinth level. |
| 21 | Thermo-Mechanically Treatedbars of gradeFe-500D or more. |
| 22 | Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3(1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 23 | Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS: 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : |
| 24 | 250x16 mm |
| 25 | Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : |
| 26 | 150x10 mm |
| 27 | Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : |
| 28 | 125 mm |
| 29 | 100 mm |
| 30 | Providing and fixing factory made uPVC door frame made of uPVC extrudedsectionshavinganoveralldimensionasbelow(tolerance ±1mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame to be Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19 mm and 1 mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturer\"s specification and direction of Engineer- in-charge |
| 31 | Extruded section profile size 48x40 mm |
| 32 | Providing and fixing to existing door frames. |
| 33 | 30 mm thick factory made Polyvinyl Chloride (PVC) door shutter made of styles and rails of a uPVC hollow section of size 60x30 mm and wall thickness 2 mm (± 0.2 mm), with inbuilt decorative moulding edging on one side. The styles and rails mitred and joint at the corners by means of M.S. galvanised/ plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 25x20 mm and 1mm (± 0.1mm) wall thickness. The lock railmade up of \"H\" section, a uPVC hollow section of size 100x30 mm and 2 mm (± 0.2 mm) wall thickness fixed to the shutter styles by means of plastic/ galvanised M.S. `U\" cleats. The shutter frame filled with a uPVC multi- chamberedsinglepanelof sizenot less than620mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness . The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer\"s specification and direction of Engineer-in- charge. |
| 34 | Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. |
| 35 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. |
| 36 | Electric resistance or induction butt welded tubes |
| 37 | Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer. |
| 38 | G.I. pipes |
| 39 | Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement: 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. |
| 40 | Providingand fixingplainmultipurpose cement board(Hight pressure steam cured) with suitable screws for cement particle board in ceiling etc. complete (frame work to be paid seperatately). |
| 41 | 6 mm thick Cement fiber board, Type-B, Category-III as per IS: 14862 :2000 |
| 42 | Providing and fixing on wall face unplasticisedRigidPVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. |
| 43 | 75 mm diameter |
| 44 | 110 mm diameter |
| 45 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS :5382, leaving 10 mm gap for thermal expansion. |
| 46 | Bend 87.5° 1) 75 mm bend |
| 47 | Bend 87.5° 2)110 mm bend |
| 48 | Providing &fixing at all heights, levels and locations colour finish Aluminium alloy roofing sheets of alloy IS designation 31500, temper Hx8 conforming to IS 737 and dimensions as per IS code 2676 with characteristics of good formability and corrosion resistance. The profile sheets shall be fixed to truss members in slope or required pitch or curvature with Hex cap headed self drilling/tapping Stainless steel screws M6, 50 mm long with 3 mm EPDM seal washer etc. all inclusive of labour, scaffolding, T&P and sundries etc. complete as per directions of the Engineer-In-Charge. (Cost of truss/frame work shall be paid separately). |
| 49 | 0.71mm, AluminiumColour coatedtroughedprofile with center to center pitch of 200 mm, depth of 32 mm, overall profile width 1092 mm, cover width 1000 mm. |
| 50 | ProvidingandfixingofPre-coatedcolourormillfinishAluminium Roofing Accessories in 0.71 mm thickness ,Alloy 31500 (IS designation) [Aluminium Alloy (AA) 3004 (ISO designation)]. For colour, coating shall be 5-7 microns epoxy primer on both sides of the sheet and polyester top coat 15-18 microns, using self drilling/tapping SS screws of size 6 x 50 mm with 3 mm thick EPDM seal and SS plain washer complete: |
| 51 | Precoated/mill finish aluminium Ridges plain (500- 600mm) |
| 52 | Precoated/mill finish aluminium Gutter (600 mm over all girth) |
| 53 | 12 mm cement plaster of mix: |
| 54 | 1:4(1 cement: 4 fine sand) |
| 55 | 12 mm cement plaster finished with a floating coat of neat cement of mix: |
| 56 | 1:4(1 cement: 4 fine sand) |
| 57 | Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gram/litre, of approved manufacturer and of required shade and colour all complete to achieve even shade and colour: |
| 58 | New work(twoormorecoats)over andincludingwater thinnable priming coat with cement primer having VOC content less than 50 gram/litre |
| 59 | Finishing walls with Acrylic Smooth exterior paint of required shade: |
| 60 | New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm) |
| 61 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : |
| 62 | Two or more coats on new work |
| 63 | Painting with black anti-corrosive bitumastic paint of approved brand and manufacture to give an even shade: |
| 64 | Two or more coats on new work |
| 65 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 66 | Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. |
| 67 | Nominal concrete 1:3:6 or richer mix (including equivalent design mix) |
| 68 | Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 metres lead : |
| 69 | Of area 3 sq. metres and below |
| 70 | Dismantling wood work in frames, trusses, purlins and rafters up to 10 metres span and 5 metres height including stacking the material within 50 metres lead : |
| 71 | Of sectional area 40 square centimetres and above |
| 72 | Dismantling roofing including ridges, hips, valleys and gutters etc., and stacking the material within 50 metres lead of: |
| 73 | G.S. Sheet |
| 74 | Dismantling wooden boardings in lining of walls and partitions, excluding supporting members but including stacking within 50 metres lead : |
| 75 | Thickness above 10 mm up to 25 mm |
| 76 | Dismantling cement asbestos or other hard board ceiling or partition walls including stacking of serviceable materials and disposal of unserviceable materials within 50 metres lead. |
| 77 | Providing and fixing G.I. chain link fabric fencing of required width in mesh size 50x50 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-in- charge. |
| 78 | Made of G.I. wire of dia. 4 mm, PVC coated to achieve outer dia not less than 5 mm in required colour and shade |
| 79 | Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: |
| 80 | White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests |
| 81 | Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : |
| 82 | W.C. pan with ISI marked white solid plastic seat and lid |
| 83 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: |
| 84 | White Vitreous China Flat back wash basin size 450x 300 mm with single 15 mm C.P. brass pillar tap |
| 85 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. |
| 86 | Semi rigid pipe 1) 32 mm dia |
| 87 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply and all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.Internal work - Exposed on wall |
| 88 | 20 mm nominal dia Pipes |
| 89 | 25 mm nominal dia Pipes |
| 90 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work |
| 91 | 40 mm nominal dia Pipes |
| 92 | Providing and fixing uplasticised PVC connection pipe with brass unions : |
| 93 | 45 cm length 1) 15 mm nominal bore |
| 94 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : |
| 95 | 15 mm nominal bore |
| 96 | Providing and fixing PTMT stop cock of approved quality and colour. |
| 97 | 20 mm nominal bore, 89 mm long, weighing not less than 88 gms |
| 98 | Providing and fixing PTMT grating of approved quality and colour. |
| 99 | Circular type 1) 100 mm nominal dia |
| 100 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fastenersto be paid for separately) : |
| 101 | For fixed portion 1) Powder coated aluminium (minimum thickness of powder coating 50 micron |
| 102 | Forshuttersofdoors,windows&ventilatorsincluding providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) |
| 103 | Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 104 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): |
| 105 | With float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm) |
| 106 | Providing and fixing powder coated aluminium work (minimum thickness of powder coating 50 micron) consisting of tee/ angle sections, of approved make conforming to IS : 733 in frames of false ceiling including aluminium angle cleats with necessary C.P. brass/ stainless steel sunk screws, aluminium perimeter angles fixed to wall with stainless steel rawl plugs @ 450 mm centre to centre and fixing the frame work to G.I. level adjusting hangers 6 mm dia. with necessary cadmium plated machine screws all complete as per approved architectural drawings and direction of the Engineer-in-charge (level adjusting hangers, ceiling cleats and expansion hold fasteners to be paid for separately). |
| 107 | Providing and fixing stainless steel (SS 304 grade) adjustable friction windows stays of approved quality with necessary stainless steel screws etc. to the side hung windows as per direction of Engineer-in-charge complete. |
| 108 | 355 X 19 mm |
| 109 | Providing and fixing aluminium casement windows fastener of required length for aluminium windows with necessary screws etc. complete. |
| 110 | Powder coated minimum thickness 50 micron aluminium |
| 111 | Providing and fixing anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge. (Only weight of grill to be measured for payment). |
| 112 | Providing and fixing in positionfacias and eaves board with 12mm thick PVC board 30 cm wide including fixing with nuts and bolts, screw etc. complete. |
| 113 | Providingand laying hollow cement concrete blockwalling200mm thick consistinghollow block of size 400 mm x200mm x200mm of mix 1:3:6 (1 Cement : 3 Coarse sand: 6 Graded stone agg. 10mm nominal down size) laid in cement mortar 1:6 ( 1 Cement : 6 Coarse sand). |
| 114 | Upto floor five level |
| 115 | Providingand laying hollow cement concrete blockwalling100 mm thick consistinghollow block of size 400 mm x100mm x200mm of mix 1:3:6 (1 Cement : 3 Coarse sand: 6 Graded stone agg. 10mm nominal down size) laid in cement mortar 1:6 ( 1 Cement : 6 Coarse sand). |
| 116 | Constructing CC masonry manhole with R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand (Zone-III): 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (Zone-III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : |
| 117 | Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) . |
| 118 | Providing and laying United Polyethylene Septic Tank made of Polyethylene Septic tank made of Polythylene in a single moulding with 3 chamber and 2 manholes, the high wall/thickness of septic tank should with stand load and pressure of the earth to a great extent. |
| 119 | Type--II-1000 mm x 2000 mm, 20-25 flushing per day |
| 120 | Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor singlecorecableinsurface /recessedmediumclassPVC conduit, with modular switch, modular plate, suitable GI box and earthingthepointwith 1.5sq.mm FRLSPVC insulated copper conductor single core cable etc. as required. |
| 121 | Group C |
| 122 | Wiringforlight/powerplugwith 2X4sq.mmFRLSPVC insulatedcopperconductorsinglecorecableinsurface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required. |
| 123 | Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. |
| 124 | 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire |
| 125 | 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire |
| 126 | 2 X 6 sq. mm + 1 X 6 sq. mm earth wire |
| 127 | Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable inthe existing surface/ recessed steel/ PVC conduit as required. |
| 128 | 2 x 1.5 sq. mm |
| 129 | Supplying and fixingtwo module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required. |
| 130 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required. |
| 131 | Supplying and fixing 3pin, 5A ceiling rose on the existing junctionbox/woodenblockincludingconnectionsetc.as required. |
| 132 | Installation ,Testing,Commissioningofwallbracket/ceiling fittings of all sizes and shapes containing upto two GLS/CFL/LED lampsperfitting,completewithallaccessoriesincluding connections etc. as required. |
| 133 | Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable etc. as required. |
| 134 | Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required. |
| 135 | Upto 450 mm sweep |
| 136 | Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providng and fixing 2 nos. 3 pin 5/6 A modular socket outlet and 2 nos. 5/6 A modular switch, connections etc. as required. (For light plugs to be used in non residential buildings). |
| 137 | SupplyingandfixingPVC batten/angle holderincluding connections etc. as required. |
| 138 | Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) |
| 139 | 4 way (4 + 12), Double door |
| 140 | Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, \"C\" curve, miniature circuit breaker suitable for inductive load of followingpolesintheexistingMCBDBcompletewith connections, testing and commissioning etc. as required. |
| 141 | Single pole |
| 142 | Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. |
| 143 | 63 A |
| 144 | Supplying and fixing DP sheet steel enclosure on surface/ recess along with 25/32 A 240 V \"C\" curve DP MCB complete with connections, testing and commissioning etc. as required. |
| 145 | Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required. |
| 146 | Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required. |
| 147 | Upto 35 sq. mm |
| 148 | LayingandfixingofonenumberPVCinsulatedandPVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required. |
| 149 | Upto 35 sq. mm (clamped with 1mm thick saddle) |
| 150 | Erection of metallic pole of following length in cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) foundation including excavation and refilling etc. as required. |
| 151 | Above 4.5 metre and upto 6.5 metre |
| 152 | Supplying of LED 20 Watts polycaronate Battern/ Tubelight 4-ft cool day light similar to Wipro Garnet with lamp 20 W LED 6500 K or its equivalent. |
| 153 | Supply of 12 Watt LED recessed ceiling light cool day light 6500k Wipro Garnet or equivalent. |
| 154 | Supplying of 100 Watts LED Street light with waterproof IP65, anticorrossion and anti rust, super brite of 3500 Lumens cool white, operating voltage AC 100V to 300 V make D\"Mak or equivalent. |
| 155 | Supplying of 50 Watts LED Flood light with waterproof IP65, anticorrossion and anti rust, super brite of 3500 Lumens cool white, operating voltage AC 100V to 300 V make D\"Mak or equivalent. |
| 156 | Supply of LED bulb of 9 Watts,white B22 Similar to Eveready cool day light or equivalent to ISI specification. |
| 157 | Supplying of Energy Saving A.C. Ceiling fan 1200 mm sweep, with all accessories .similar to Polycab Affeciente NeoEteri BLDC 5 star rated or equivalent |
| 158 | Supply of metallic exhaust fan of size 230 mm similar to Khaitan fresh or its equivalent. |
| 159 | Supplying of following size XLPE insulated heavy duty armoured aluminium conductor UG cable of 1.1 KV grade conforming to IS: No. 7098 (Part-I) and IS: No. 1554 (Part-I) 1958 as applicable. |
| 160 | 6.0 Sq.mm x 2 Core |
| 161 | Supplying and Laying of one Number Double walled corrugated high density poly thylene pipe having corrugation on the outer wall and plain surface inner wall conforming to IS: No. 14930 Part I & II complete with necessary HDPE filling for protection of 1.1 KV grade directly in ground at the depth of 50 cm i/c excavation & refilling the trench etc as reqd. |
| 162 | 50 mm outerdia & 38 mm inner dia |
| 163 | Providing and fixing waterproof cable looping out box made out of SMC and of size 450mmx375mmx200mm with hinged door and locking arrangement |
| 164 | Supplying installation, testing and commissioning of ASHLOK make SEE brand safe earthing electro type-19, 50mm dia length 2 mtrs and inner space to be filled with crystaline conductive mixture including filling up with elelctrodite (Back fill compound ) as reqd for safe earth electrode and providing masonary enclusure with cover plate having locling arrangement etc as reqd. |
| 165 | Manufacturing and Supplying of Street Light Pole 4.5 mtr long from ground made out of medium Class GI pipe of size 65 mm dia & 01 No 40 mm dia 2 mtr long G.I.Pipe medium class for mounting of 100 watt LED Street Light fitting at the pole top including bending the pipe to required shape and 300mm x 6 mm MS base plate welded to the bottom making holes & Sintex box of size 155 x 100 x 60(mm) with 01 No. 6 amps MCB, Din Channel & Nut & Bolt for fastening the base i/c painting with one coat of metalic primer & two coats of metalic white paint as reqd. |
| 166 | Providing and fixing 63 Amps capacity TP&N disconnector fuse switch unit in sheet steel enclosure with 3 Nos 63 Amps Kit Kat fuse carrier making connection with suitable guage copper conductor etc as required similar to Havells Make Cat No.IHKDTW4063 or equivalent. |
