|
| 1 | M&L for surface dressing n.exc 15 cm deep and getting out in hard/dense soil complete all as specified and directed by the Engg-in-Charge. |
| 2 | M&L for Excavation in trenches n exc. 1.5m in depth for foundation and not exc 10 sqm on plan and not exc 1.5m in depth and getting out in hard/dense soil complete all as specified and directed by the Engg-in-Charge. |
| 3 | M&L for PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) in foundation,filling and mass concrete complete all as specified and directed by the Engg-in-Charge. |
| 4 | M&L for precast cement concrete type C1, 1:3:6 using 20mm graded stone aggregates, block masonary with solid blocks, exc 10cm width and setting in cement mortar 1:6 complete all as specified and directed by the Engg-in-Charge. |
| 5 | M&L for Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; in flat rough finished surfaces of concrete complete all as specified and directed by the Engg-in-Charge. |
| 6 | M&L Formwork to sides of pillars, posts, struts, piers, columns and stanchions in flat fair finished surfaces of concrete complete all as specified and directed by the Engg-in-Charge. |
| 7 | M&L Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc in flat rough finished surfaces of concrete complete all as specified and directed by the Engg-in-Charge. |
| 8 | M&L for TMT bars Mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including for mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by the Engg-in-Charge. |
| 9 | M&L for TMT bars Mild steel bars 5mm dia and over upto and including 10mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including for mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by the Engg-in-Charge. |
| 10 | M&L forreinforcement cement concrete (design mix) M-25 (using 20mm graded crushed stone aggregate) in foundation , including rafts, footing,foundation beams, plinth beams, bases for coloums etc.complete all as specified and directed by the Engg-in-Charge. |
| 11 | M&L for reinforcement cement concrete (design mix) M-25 (using 20mm graded crushed stone aggregate) as in columns, pillars, piers, posts and struts, complete all as specified and directed by Engr-in-Charge. |
| 12 | M&L for reinforcement cement concrete (design mix) M-25 (using 20mm graded crushed stone aggregate)as in beams, cantilevers, bressumers, lintel over 1.5m span complete all as specified and directed by Engr-in-Charge. |
| 13 | Returning filling incl spreading leveling watering and well ramming in layers not exceeding 25 cm in any type of soil complete all as specified and directed by the Engg-in-Charge. |
| 14 | Removing excavated material n.exc. 50 m and deposited were directed at a level n.exc.1.5 m above the starting point complete all as specified and directed by the Engg-in-Charge. |
| 15 | M&L for Earth filling in floors including spreading, levelling and ramming with watering as required in layers n.exc 25cm thick complete all as specified and directed by the Engg-in-Charge. |
| 16 | M&L for hard core of broken stones or boulders of gauge in exc 63mm but n exc 100mm deposited spread and levelled in layers n. exc 15cm thick incl watering and rolled to true surface complete all as specified and directed by the Engg-in-Charge. |
| 17 | M&L for 75mm thick PCC (1:4:8) type D2 using 40mm graded aggregate as in sub base to floor or similar works complete all as specified and directed by the Engg-in-Charge. |
| 18 | M&L for 75mm PCC 1:3:6 type C2 (using 40mm grade aggregate) thick as in plinth protection/paving or similar works complete all as specified and directed by Engr-in-Charge. |
| 19 | M&L for rendering 10mm thick in CM 1:6 on fair faces of brick work or concrete surfaces, finishing even and smooth without using extra cement complete all as specified and directed by Engr-in-Charge. |
| 20 | M&L for rendering 15mm thick in CM 1:4 on other fair faces of brick work or concrete surfaces in two layers 10mm & 5mm thick with WPC to be used in outer layer of 5mm thick, finishing even and smooth without using extra cement complete all as specified and directed by Engr-in-Charge. (WPC measured and paid seperately) |
| 21 | Supply only liquid waterproofing compound complete all as specified and directed by Engr-in-Charge. |
| 22 | M&L for Fe 290 (Gde E-165) for roof trussed (framed), trussed, purlins, crane gantries, rails and fastening and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc complete all as specified and directed by Engr-in-Charge. |
| 23 | M&L for Rolled mild steel Gde Fe-290 (Gde E-165) as in Plates (plain or chequered) channels,angle sections, square cut or notched (ordinary & counter sunk) forming holes, with riveted, bolted or welded attachment complete all as specified and directed by Engr-in-Charge. |
| 24 | S&F 20mm dia of neck mild steel rag or lewis bolts, screwed one end, with hexagonal or square nuts and washers, the other end enlarged and jagged or lewised, length of bolt exc 30cm long complete all as specified and directed by Engr-in-Charge. |
| 25 | S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed by Engr-in-Charge. |
| 26 | S&F Pre-painted galvatume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engr-in-Charge. |
| 27 | M&L for 25mm thick PCC type B0 1:2:4 (12.5mm graded aggregate) as in floor or similar works finished rough to receive tiles complete all as specified and directed by Engr-in-Charge. |
| 28 | M&L for Non skid Ceramic colouredtiles 7 to 8mm thickarea of each tiles exc 0.06 sqm but nexc 0.11 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm screed bed in CM 1:6 complete all as specified and directed by Engr-in-Charge. |
| 29 | M&L for Glazed ceramic coloured tilesin vertical surfaces 350x450x7mm thick etc set and jointed in neat cement slurry and pointed in white/coloured cement to match the shade of tile over 10mm thick rendering in cement mortar 1:4 in backing coat of plaster for skrting/dado complete all as specified and directed by Engr-in-Charge. |
| 30 | M&L for 20mm thick granite (of any type) work table rubbed and polished) in steps, pillars, jambs, window cills, cooking plateform/wash basin plateform etc and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed by Engr-in-Charge. |
| 31 | S&F 2nd class softwood(KAIL) as inPlain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed by Engr-in-Charge. |
| 32 | S&F 35mm thick2nd class soft wood (KAIL) plain framed panelled shutters (any No of pannels) with panels of timber flat on both sides (Feather edgeed), or of veneered particle board medium density, wood particle board withcommercial face veneers, supplied and fitted to chowkats complete all as specified and directed by Engr-in-Charge. |
| 33 | S&F 30 mm thick 2nd class soft wood (KAIL) glazed and skeleton shutter open rebated and prepared to receive glass, gauge etc dividedinto squares with plain chamfered or rounded, mitred and rebated sash bars any numbers complete all as specified and directed by Engr-in-Charge. |
| 34 | S&F 100 mm butt hinges medim weight cold rolled mild steel and fixed with screws or welded complete all as specified and directed by Engr-in-Charge. |
| 35 | S&F75mm butt hinges medium weight cold rolled mild steel complete all as specified and directed by Engr-in-Charge. |
| 36 | S&F 200mm anodised aluminium barrel tower bolt extruded sections complete all as specified and directed by Engr-in-Charge. |
| 37 | S&F 150mm anodised aluminium barrel tower bolt extruded sections complete all as specified and directed by Engr-in-Charge. |
| 38 | S&F 125mm extruded aluminium alloy handles febricated type anodised complete all as specified and directed by Engr-in-Charge. |
| 39 | S&F 100mm extruded aluminium alloy handles febricated type anodised complete all as specified and directed by Engr-in-Charge. |
| 40 | S&F 250mm Aluminium alloy, anodised,sliding door bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and directed by Engr-in-Charge. |
| 41 | S&F 3mm thick sheet glass, ordinary quality and glazing with oil putty or wooden beading in square n exc 0.5 sqm complete all as specified and directed by Engr-in-Charge. |
| 42 | M&L for preparation of new plastered surfces of walls and applying three coat wash complete all as specified and directed by Engr-in-Charge. |
| 43 | M&L for preparation of new plastered surfaces of walls and applying two coats of cement based paint over a coat of primer complete all as specified and directed by Engr-in-Charge. |
| 44 | M&L for preparation of wood and wood based material surface of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed by Engr-in-Charge. |
| 45 | M&L for prepation of new or previously untreated surfaces of steel of any description, over 10cm in width or girth, not otherwise described andapplying two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed by Engr-in-Charge. |
| 46 | S&F High grade stainless steel toilet pan of size 58.5x48.2x30.0 cm (excludiig flushing cistern and flush pipe) incl PCC for fixing complete all as specified and directed by Engr-in-Charge. |
| 47 | S&F PVC flushing cistern valveless syphonic action type flushing cistern low level 10 Ltrs white with inlet ball valve float and handle incl bracket complete all as specified and directed by Engr-in-Charge. |
| 48 | S&F vitreous chinaurinal bowl type complete including providing and fixing plugs bedding urinal against wall in CM 1:2 for securing urinals to plug with and incl 60cm long brass screw pointing around urinal back in cement complete all as specified and directed by Engr-in-Charge. |
| 49 | S&F 32mm CP waste coupling with waste pipebut suitable for urinalscomplete all as specified and directed by Engr-in-Charge. |
| 50 | S&F CP urinal spreadercomplete all as specified and directed by Engr-in-Charge. |
| 51 | S&F Wash Hand Basin counter sunk type ovel under/over counter shape fixedon stone slab incl necessary cutting etc of size as required at site complete all as specified and directed by Engr-in-Charge. |
| 52 | S&F pillar tap 15 mm bore fancy type cast copper alloy with capstan heads chromium plated screwed down high pressure with or without lettered Hot or Cold with long screwed and fly screwed for iron pipe complete all as specified and directed by Engr-in-Charge. |
| 53 | S&F 15mm dia chromium plated fancy type Bib tap with round handle screwed down screwed for iron pipe or brass ferrule complete all as specified and directed by Engr-in-Charge. |
| 54 | S&F 15mm dia chromium plated fancy type stop valves/angle cock screwed down high pressure, screwed for iron pipe complete all as specified and directed by Engr-in-Charge. |
| 55 | S&F PVC connection 15mm size, with PTMT nuts of length 600mm complete all as specified and directed by Engr-in-Charge. |
| 56 | S&F 32mm CP waste coupling with waste pipe complete all as specified and directed by Engr-in-Charge. |
| 57 | S&F 600x450mm beveled edge mirror of selected quality, thickness of glass 5mm, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed by Engr-in-Charge. |
| 58 | S&F Towel rail 600 mm long PTMT fixed with and incl chromium plated brass screws and wooden/ plastic cleats (Min Wt 170 gms) complete all as specified and directed by Engr-in-Charge. |
| 59 | S&F PVC (SWR) floor trap, plain with grating including jointing with solvent cement diameter of outlet 75mm complete all as specified and directed by Engr-in-Charge. |
| 60 | S&F75mm bore PVC (SWR) bends any radius with access door complete all as specified and directed by Engr-in-Charge. |
| 61 | S&F75mm bore PVC (SWR) junction single, (Single T) equal or unequal with access door complete all as specified and directed by Engr-in-Charge. |
| 62 | S&F 110mm PVC (SWR) \"P\" trap complete all as specified and directed by Engr-in-Charge. |
| 63 | S&F 110mm bore PVC (SWR) junction single, (Single T) equal or unequal with access door complete all as specified and as directed |
| 64 | S&F 110mm bore PVC (SWR) bends any radius with access door complete all as specified and directed by Engr-in-Charge. |
| 65 | S&F75mm bore PVC (SWR) vent cowl complete all as specified and directed by Engr-in-Charge. |
| 66 | S&F PVC (SWR) pipes110mm dia single socketed in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed by Engr-in-Charge. |
| 67 | S&F PVC (SWR) pipes 75mm dia single socketed in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed by Engr-in-Charge. |
| 68 | S&F 25mm outer dia 3-layer PPR polypropylene random copolymer concealed pipes SDR 7.4 (PN16) UV stablized and antimivrobial fusion welded having thermal stability for hot & cold water supply including all PPR plain & brass threaded polypropylene random fittings fixed complete to wall, ceiling or in floors complete all as specified and directed by Engr-in-Charge. |
| 69 | S&F 20mm outer dia 3-layer PPR polypropylene random copolymer concealed pipes SDR 7.4 (PN16) UV stablized and antimivrobial fusion welded having thermal stability for hot & cold water supply including all PPR plain & brass threaded polypropylene random fittings fixed complete to wall, ceiling or in floors complete all as specified and directed by Engr-in-Charge. |
| 70 | S&F rotational moulded polytheline water storage tank 1000 Ltrs capacity (cylinercial/vertical with closed top) hoisted and fixed in position complete all as specified and directed by Engr-in-Charge. |
| 71 | S&F Gun metal globe or gate valve with iron wheel head screwed both ends for iron pipe and fixed of 20mm bore dia complete all as specified and directed by Engr-in-Charge. |
| 72 | M&L for providing PCC (1:2:4) type B-1 using 20mm graded stone aggregate as in copings, benching or similar works complete all as specified and directed by Engr-in-charge. |
| 73 | M&L for precast RCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in cover slab for manhole etc with plane faces complete all as specified and directed by Engineer-in-Charge. |
| 74 | M&L for TMT bars 6mm to 8 mm dia cut to length bent to shape required including cranking, bending, hooking ends and binding with MS wire (annealed) not less than 0.9 mm dia complete all as specified and directed by the Engineer-in-Charge. |
| 75 | Removing excavated material (soil) exc. 500 m but n.exc. 1.5km and depositing where directed at a level n.exc. 1.5 m above the starting point complete all as specified and directed by Engr-in-Charge. |
| 76 | M&L for HDPE DWC pipe 200mm internal dia and external dia 230mm SN-04 confirming to SN-4 fixed with rubber seal and coupler required with and including suitable bends 90/60/45 degree etc single Y junction laid in tranches and jointed with cement solvent including testing complete all as specified and as directed by Engineer-in-Charge. |
| 77 | M&L for concrete bed to drain pipe in PCC (1:4:8) type D-2 (using 40mm graded crushed stone aggregate) including packing under and haunching against the sides of pipe after laid and tested for 200 mm bore pipe complete all as specified and directed by Engr-in-Charge. |
| 78 | M&L for Provn of Sockage well incl exc in hard dense soil, foundation in PCC 1:3:6, sockage well of honey combed masonry, incl provn of intercepting chamber, screen chamber stone work in CM 1:4 and RCC cover slab in M-25 cement concrete incl filling with stone boulder complete of 3.00 dia and 3.00m deep complete all as specified and directed by Engr-in-Charge.(Ref Drg No. CESZ/TD/1078/2011, Sheet 1/1) |
| 79 | M&L for Point wiring for light/fan/bell with FRLS cable of 1.5sqmm PVC insulated (red/blue/yellow for phase, black for neutral and green for earth) unsheathed multistranded copper conductor 1100 volts grade in and including not less than 2mm thick PVC casing capingwith all accessories and 1.5sqmm green in colour PVC insulated multistranded copper conductor FRLS cablefor earth continuity connected to common earth dolly incl MS/GI sunken box with 3mm thick pre laminated hylum sheet/PVC box with back plate,flush/surface type for mounting fittings such as switches,socket,and regulator complete all as specified and directed for one light point or bell/buzzer pointcontrolled by one switch complete all as specified and directed by Engr-in-Charge. |
| 80 | All as per Srl item No 79 above but usingcable size 2.5 Sqmm for one 3 pin socket outlet 5 Amps independent board complete all as specified and directed by Engr-in-Charge. |
| 81 | S&FSwitch socket combination 2 in 1, and 3 and 2 pin, 5 Ampsflush type complete all as specified and directed by Engr-in-Charge. |
| 82 | All as per Srl item No. 79 here in before but usingcable size 2.5 Sqmm for one 3 pin socket outlet 15 Amps on independent board complete all as specified and directed by Engr-in-Charge. |
| 83 | S&F Switch socket combination 2 in 1, 5 and 15 Ampsflush type complete all as specified and directed by Engr-in-Charge. |
| 84 | S&F Switch piano flush type 5 Amps, single pole one way complete all as specified and directed by Engr-in-Charge. |
| 85 | M&L of ceiling rose on PVC square blocks surface bakelite 3 terminal complete all as specified and directed by Engr-in-Charge. |
| 86 | S&F LED lights fitting, surface mounting ultra slim economical LED batten of 1x18W/20W,lumen out put 100lm/wattt, CCT:6500K /3000K, PF>0.9, in extruded PC housing and round/square shaped diffuser including connecting up with two core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed by Engr-in-Charge. |
| 87 | S&F in replacement LED light fitting mirror type with high output diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed by Engr-in-Charge. |
| 88 | S&F in replacement exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz,RPM 1200, Copper winding of sweep 250 mm including making arrangement for fixing complete all as specified and directed by Engr-in-Charge. |
| 89 | S&F in replacement Sheet metal enclosure for DB\"s Double door,single pole and neutral, 240V, 8 way with 200 Amp rated bus bar including blanking plates where required complete all as specified and directed by Engr-in-Charge. |
| 90 | S&Fin replacement 240V 10 KA C curve MCB SPN 32 Amp in the MCB DB complete with connection complete all as specified and directed by Engr-in-Charge. |
| 91 | S&F in replacement 240V 10 KA C curve MCB SP 5 to 32 Amp in the MCB DB complete with connection & testing complete all as specified and directed by Engr-in-Charge. |
| 92 | M&L for Earthing complete with galvanised steel earth plate electrode 60cm×60cm×6.0mmthick, buried directly in ground vertically (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers made out of galvanised iron or steel and connected to main switch board or equipment, including watering arrangement with GI medium grade 20mm bore watering pipe with funnel and wire mesh with PCC chamber CI cover with frame including 15mm dia GI pipe light grade for protection of earthing lead etc including necessary excavation in any type of strata, returning, filling, removal of soil outside MD land, filling of charcoal and salt complete all as shown in electrical plate No. 3 of MES Sch Part I, connected to earthing test point all as specified or indicated including testing on completion complete all as specified and directed by Engr-in-Charge.Notes:- (i) Earth continuity conductor including protection pipe upto 7.5 meters from earth electrode will be include in unit rate,(ii) Arrangement for earth resistance test should be carried out by the contractor. No extra payment shall be provided for the same. |
| 93 | S&Fin replacement1100 volts grade heavy duty 16 Sqmm 2 core flat cable PVC insulated aluminium standard conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections complete all as specified and directed by Engr-in-Charge. |
| 94 | M&L for laying of GI tubing medium grade ofISI marked complete with all necessary fittings of 20 mm bore size laid in trenches/ floors/wall complete all as specified and directed by Engr-in-Charge. |
