|
| 1 | Taking down chowkats or frame with shutter (without taking off shutters from the frame)exc 1.5 Sqm but n.exc 4 sqm each complete all as specified and directed. |
| 2 | Taking down shutter of any description exc 1sqm but not exc 2 Sqm each and removing unserviceable materials from site of work complete all as specified and directed. |
| 3 | M&L for factory made Pressed steel frames 125 x 60 x 1.25mm thick for doors with one or more rebates including necessary fixing lugs, hinges, lock, strike plate etc complete including PCC (1:3:6) type C-0 (using 12.5 mm graded stone aggregate) as in filling hollow portion of frame complete all as specified and directed. |
| 4 | M&L for factory made Pressed steel frames 105 x 60 x 1.25mm thick for doors with one or more rebates including necessary fixing lugs, hinges, lock, strike plate etc complete including PCC (1:3:6) type C-0 (using 12.5 mm graded stone aggregate) as in filling hollow portion of frame complete all as specified and directed. |
| 5 | S&F for Mild steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete all as specified and directed., drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging, also fastening and fixing complete, quality conforming grade Fe- 290 or E- 165 complete all as specified and directed. |
| 6 | S&F Factory made flush shutter 35 mm thick solid core construction with block board core and plywood face panels commercial type complete all as specified and directed. |
| 7 | S & F 35 mm thick, factory made, llnd class hard wood (Sal) glazed and skeleton shutter open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, charmfered or rounded, fitted with cut and mitred beads for securing glass, etc., sizes of members of shutters as specified in SSR Part l, section 8 clause 8.24 (a); supplied and fitted to chowkhats complete all as specified and directed. |
| 8 | S&Fgalvanized mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanized wire staples complete all as specified & directed. |
| 9 | M&L for applying two coats of synthetic enamel paint over a coat of pink primer on wooden surface over 10 cm width or girth including preparation of new or previously untreated wood surfaces complete all as specified and directed. |
| 10 | M&L for applying two coats of synthetic enamel paint over a coat of red oxide on steel surface over 10 cm width or girth including preparation of new or previously untreated steel surfaces complete all as specified and directed. |
| 11 | S&F Aluminium alloy, anodised, 300 mm sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed. |
| 12 | S&F 200 mm long aluminium anodized barrel tower bolt of extruded section complete all as specified and directed. |
| 13 | S&F 150 mm long aluminium anodized handle cast type complete all as specified and directed. |
| 14 | S&F 100 mm long stainless steel hinges type B-12 and fixed with screw/ welding complete all as specified and directed. |
| 15 | S&F Floor door stopper 150 mm long of aluminium alloy body and tongue anodized with hard drawn steel spring fixed in floor complete all as specified and directed. |
| 16 | Taking down chowkats or frame with shutter (without taking off shutters from the frame) n exc 1.5 Sqm each complete all as specified and directed. |
| 17 | S&F of factory made soild PVC door frame of size 50mmx47mm made out of 5mm thick single side prelam PVC sheet reinforced with mild steel square tube, supplying & fixing in opening as per specification and drawing complete all as specified and directed. |
| 18 | S & F Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2 mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face with particle board core, supplying & fixing in frame at site as per specification & drawing complete all as specified and directed. |
| 19 | S&F 150mm long aluminium anodized barrel tower bolt of extruded section complete all as specified & directed. |
| 20 | M&L 100 mm long aluminium anodized handle cast type complete all as specified and directed. |
| 21 | S&F 75 mm long stainless steel hinges type B-12 and fixed with screw/ welding complete all as specified and directed. |
| 22 | S&F Steel windows with side hungshutters including projecting typehinges with steel handle, and steelpeg stay,complete with glazing bars,dovetailed or welded including guard bars complete all as specified and directed. |
| 23 | S&F Steel ventilators with centre hungshutter including two pairs of brasscup pivots, catch spring and pulleywheel, complete typehinges with steel handle, and steelpeg stay,complete with glazing bars,dovetailed or welded including guard bars complete all as specified and directed. |
| 24 | Taking down wood shutter exc 1 sqm but not exc 2.00 sqm including easing & adjusting and refixing on same opening with same hardware etc complete all as specified and directed. |
| 25 | S&F in repair Aluminium alloy, anodised, 300 mm sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed. |
| 26 | S&F in repair200 mm long aluminium anodized barrel tower bolt of extruded section complete all as specified and directed. |
| 27 | S&F in repair 150 mm long aluminium anodized handle cast type complete all as specified and directed. |
| 28 | S&F in repair100 mm long stainless steel hinges type B-12 and fixed with screw/ welding complete all as specified and directed. |
| 29 | S&F in repair Floor door stopper 150 mm long of aluminium alloy body and tongue anodized with hard drawn steel spring fixed in floor complete all as specified and directed. |
| 30 | M&L for welding in repairs n. exc 2.5 cm in length and n. exc 6mm thick complete all as specified and directed. |
| 31 | M&L for welding in repair exc 2.5 cm but n. exc 5.0 cm length and n exc 6mm thick complete all as specified and directed. |
| 32 | M&L for PCC 1:3:6, type C-1 (using 20mm graded stone aggregate) for embedding of hold fast etc including disturb surface ofexisting position complete all as specified and directed. |
| 33 | S&F powder coatedanodized aluminium door & framefor door, windows and ventilator with one or more rebates incl joining cleat for fixing etc of weighing 0.55 kg/m complete all as specified and directed. |
| 34 | S&F of power coated any colour anodised aluminium door shutter, aluminium section weighting 0.55 kg/m incl necessary jointing cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading screws etc complete all as specified and directed. |
| 35 | S & F powder coated Anodised aluminium window and ventilator shutters, side hung type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc complete all as specified and directed. |
| 36 | S&F anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete all as specified and directed. |
| 37 | S & F powder coatedanodised aluminium three track sliding window made of extruded profiles with reqd size of aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings and plain glass on two shutters and stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixedwith stainless steel wire staples on one shutters with two nylon roller on each shutters including star lock handle complete all as specified and directed. |
| 38 | S&F 5.5 mm thick sheet glass, ordinary quality and fixed with aluminum beading and gaskit suitable for aluminum frames in squares exceeding 0.5 sqm in each pane complete all as specified and directed. |
| 39 | Description all as per item No 38.00 above but 5.00 mm thick figured glass, pin head type complete all as specified and directed. |
| 40 | S&F in repairs 3 mm thick sheet glass ordinary quantity and glazing with oil putty in square not exceeding 0.5 Sqm in each panel complete including hackingoutoldbrokenglass (anythickness, size, quality or description)from wooden frames or stone, concreteor brick surrounds, glazed with puttyor fixed with beads complete all as specified and directed. |
| 41 | S&F in repairs galvanized mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanized wire staples complete all as specified & directed. |
| 42 | S&F in repair for 3 mm thick Figured glass, pin headed type and glazing with oil putty in squares not exceeding 0.5 Sq. M in each pane complete all as specified and directed. |
| 43 | S & F in repairDoor closer (extruded section) hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and directed. |
| 44 | Dismantling of floor, hearth or wall tiles/terrazo/mozaic/Granite (floor/dado) including cement mortar bedding (but not backing), removal serviceable tiles to store and rubbish off the premises, complete all as specified and directed. |
| 45 | Material & labourglazed ceramic colouredtiles of size450x300x8-10mm thick, as in skirting/dado set and jointed in neat cement slurry and pointed in white/coloured cement to match in floor over and including 10mm thick cement screed bed of CM (1:4) complete all as specified and directed. |
| 46 | Material & labour Non-skid coloured Joint free tiles 7 to 8 mm thick (square/rectangular) area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm ,in floors etc. set and jointed in neat cement slurry and pointed in white/coloured cement to match in floor over and including 15mm thick cement screed bed of CM (1:6) complete all as specified and directed. |
| 47 | Taking down of plaster from wall/ ceiling and soffits of chajja etcincluding racking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed. |
| 48 | Material & labour for rendering 10mm thick on other than fairfaces of brick work or concrete surfaces in CM (1:6) surfaces finished even and fair faces complete all as specified and directed. |
| 49 | Material & labour for preparation of new surfaces of wall andapplying two coats of oil bound distemper over and including one coat of JK/Birla wall care putty to match the existing as required, complete all as specified and directed. |
| 50 | M&L for 15mm thick plastering in CM 1:4 on brick surfaces of walls & finishing the surface even & smooth complete all including water proofing compound complete all as specified and directed. |
| 51 | M&L for preparation of newly plastered surfaces of walls and applying two coats of cement base paint over a coat of primer at any height (n. exc 11m) including necessary scaffolding /Centring etccomplete all as specified and directed. |
| 52 | Supply & fixing hasp and staple of size 75 mm long, safety type of aluminum anodized complete all as specified and directed. |
| 53 | Material & Labour for external 2nd class hardwood lipping 6 mm thick & 10 to 20 mmwide fixed with nails on block boards etc as in cupboard shelve kitchen cupboard etc complete all as specified and directed. |
| 54 | S&F in repairs Veneered decorative ply wood,grade I (with BWR resin)decorative veneers on one face only of thickness 12 mm ,exterior grade, fixed to timber framework with screwsas in cupboard shelves, kitchen, cupboardsetc complete all as specified and directed. |
| 55 | S&F 2nd class hard wood plain fillets, square, rectangular in section, sectional areaexe 13 sqcm & n. exe 25 sqcm clean sawn, secured with nails or bradscomplete all as specified and directed. |
| 56 | S&F in repair pre-laminated particle board 19mm thick, interior grade, pre-laminated one side with decorative choice laminations and other side balancing white laminations, fixed with nails/screws to timber frame work as in cupboard/shelves fixed complete all as specified and directed. |
| 57 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and nontoxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately) complete all as specified and directed. |
| 58 | S & FFactory Made 18mm thick 100% Solid WPC (Wood polymer Composite) decorative Laminated Board of required size comprising of virgin PVC resin of K Value 57-60 (Suspension Grade), Calcium Carbonate and natural fibers (Wood Powders/ rice husk/ wheat husk ) and Nontoxic additives, made from Extrusion process WPC foam sheet Single Extruded (Inner) with having minimum density not less than 650 kg/cbm manufactured by Certified Company, having good screw holding capacity (Screw Withdrawal strength of 2000 N (Face) & 1100 N ( Edge), Minimum Compissive of 50 N/mm2, Modulus of elasticity 850N/mm2 and resistance of spread of flame of Class A category with Property of being Termite/ Borer Free. Water/ Moisture Proof and Fire Retardant. WPC to be Laminated with PVC foil of minimum 14 microns thick of approved design pasted on both faces of shutter and fixing stainless Steel butt hinges of required size with necessary full body threaded star headed counter sunk SS Screws. Material test certificate and authentication should be compulsory provided by the manufacturing company : For WC/Bathroom/Toilet /Kitchen/Balcony Doors and Cabinets complete all as specified and directed. |
| 59 | S&F in repair soft close cabinet hinges for kitchen cabinets/cupboards from 14 mm to 22 mm Thickness complete all as specified and directed. |
| 60 | S&F in repair cupboard drawer channel set of 18 inches complete all as specified and directed. |
| 61 | S&F in repairs of drawer handle, projected drop of mild steel 50mm to 65mmlong on screw plate complete all as specified and directed. |
| 62 | Supply & fixingin repair 40mm dia Cup Board knobs fixed with nut, screws Each and washers of mild steel, brass polished complete all as specified and directed. |
| 63 | S&F Continuous (piano) hinges, mild steel, bright finish or electro galvanised, width of flap (when open) 40 mm complete all as specified and directed. |
| 64 | S&FMagnetic Catcher as in ‘Kitchen Cabinets’Cupboards, Bath Cabinets etc complete all as specified and directed. |
| 65 | S&Fof 19mm dia SS wardrobe hanger rod set for hanging cloths in wardrobe/ CB with supports at ends incl all fittings complete all as specified and directed. |
| 66 | S&F in repairs of 6 mm dia stainless steel of medium grade tie hanger set of 6 nos for wardrobe fixing in wardrobe incl fittings complete all as specified and directed. |
| 67 | M&L for door seal with stainless steel strip complete all as specified and directed. |
| 68 | S&F in repair of mild steel 300mm ordinary rat tail rod pattern springs incl roller and roller plate complete all as specified and directed. |
| 69 | S&F in repairs Stainless steel drapery rods, 25mm internal diameter including decorative type knobs including fixing arrangement with drilling holes in walls, brackets etc complete all as specified and directed. |
| 70 | S&F 0.71 mm thick plain aluminium sheeting alloy 31000 H4 in stepped flashing (measured as the minimum rectangle from which the pieces can be cut ) fitted in wall cladding,steel gates, etc., cut to size, holes punched including fixing to MS clamps with necessary bolts and nuts complete all as specified and directed. |
| 71 | S&F stainless steel self-closing hinge of 75 mm size for PVC door shutter complete as specified and directed. |
| 72 | S&F 100 mm size MS mat / glossy finish handle complete all as specified and directed. |
| 73 | S&F in repairsStain less steelbrackets for suitable 25mm dia curtain rods complete all as specified and directed. |
| 74 | S&F in repair 25mm dia Stainless steel curton rod fixed complete all as specified and directed. |
| 75 | S& F in repair stainless steel kitchen plate rack wall mounted of overall minimum size1100 x 800 mm and 250 mm deep, with partition for small/large plates etc made out of stainlesssteel gauge ,fixed with rawl plug and CP steel screws complete all as specified and directed. |
| 76 | Supply and fixing in repair looking mirror 5.50mm thick of selected quality mounted on PVC frame and back fixed to wall with screw and rawl plugs complete all as specified and directed. |
| 77 | Dismantling of asbestos cement (corrugated and semi corrugated etc) sheet in roof covering complete all as specified and directed. |
| 78 | S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet AZ - 150 thickness of sheet 0.50mm of any colour having tensile strength of 550Mpa as in roof covering/ cladding to wall, fixed with self-tapping screws complete all as specified and directed. |
| 79 | S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet AZ - 150 thickness of sheet 0.50mm of any colour having tensile strength of 550Mpa as in roof covering/ cladding to wall, fixed with self-tapping screws complete all as specified and directed. |
| 80 | S&F mild steel, plain, black sheet in hearths; covering to door shut ters; covering to door chowkats (frames);chullah hoods; waterducts; urinal troughsand funnels, etc. cut tosize edges beaded ifdirected, holes punched; including round headedscrews, cloutnails orrivets and fixed to wood or steel members, etc.with plain 40 mm lapjoints or welded/riveted seams includingbending, turning up,mitred angles, stoppedends, outlets, etc complete all as specified and directed. |
| 81 | M&L Anti termite treatment post construction for treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement :2 coarse sand) to match the existing floors complete all as specified and directed. |
| 82 | M&L Anti termite treatment post construction for treatment of voids in masonry using chemical emulsion one litre per hole, at 300mm intervals including drilling holes at 45 degree and replugging them with cement mortar 1:2 to match the existing floors complete all as specified and directed. |
| 83 | M&L Anti termite treatment post construction for treatment at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.50 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150 mm centre to centre and sealing the same complete all as specified and directed. |
| 84 | Taking down Steel/ Iron door of any size including cleaning, adjusting welding for repair wire mesh and making smooth functioning after repair of hinges, sliding door boltetc and re-fixing in same opening area not exceeding 4 Sqm each complete all as specified and directed |
