|
| 1 | Dismantling all types of masonry excepting cement concrete plain or reinforced, stacking serviceable materials at site and removing rubbish as directed within a lead of 75 m. In ground floor including roof. In Ground Floor |
| 2 | Dismantling all types of plain cement concrete works, stacking serviceable materials at site and removing rubbish as directed within a lead of 75 m. In ground floor including roof. upto 150 mm thick. In Ground Floor |
| 3 | Dismantling R.C. floor, roof, beams etc. including cutting rods and removing rubbish as directed within a lead of 75 m including stacking of steel bars. In ground floor including roof. In Ground Floor |
| 4 | Stripping off worn out plaster and raking out joints of walls, celings etc. upto any height and in any floor including removing rubbish within a lead of 75m as directed. |
| 5 | Cutting chase upto125x150mm. Ands ubsequent mending of damages. in brick wall [Cement-3.6 Kg/Mtr] |
| 6 | Earth work in excavation of foundation trenches or drains, in all sorts of soil (including mixed soil but excluding laterite or sandstone) including removing, spreading or stacking the spoils within a lead of 75 m as directed. The item includes necessary trimming the sides of trenches, levelling, dressing and ramming the bottom, bailing out water as required complete. Depth of excavation not exceeding 1500 mm. |
| 7 | Earth work in filling in foundation trenches or plinth with good earth, in layers not exceeding 150 mm including watering and ramming etc. layer by layer complete. (Payment to be made on the basis of measurement of finished quantity of work). With earth obtained from excavation of foundation. |
| 8 | Earth work in filling in compound, tank, low land, ditches etc. with good earth, in layers not exceeding 150 mm. including breaking clods and consolidating the same by ramming and dressing complete. (Payment will be made on profile measurement before and after the work). With carried earth arranged by the contractor within a radius exceeding 3 km. but not exceeding 5 km. including the cost of carried earth. |
| 9 | Filling in foundation or plinth by silver sand in layers not exceeding 150 mm as directed and consolidating the same by thorough saturation with water, ramming complete including the cost of supply of sand. (Payment to be made on measurement of finished quantity) |
| 10 | Single brick flat soling of picked jhama bricks including ramming and dressing bed to proper level and filling joints with local sand. |
| 11 | Brick work with 1st class bricks in cement mortar (1:6). In foundation and plinth. |
| 12 | 125 mm thick brick work with 1st class bricks in cement mortar (1:4) . In ground floor |
| 13 | Ordinary cement concrete (mix 1:1.5:3) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement if any, as per relevant IS codes. Pakur variety. In Ground Floor |
| 14 | Cement concrete with graded stone ballast (40 mm size excluding shuttering) In ground floor - Pakur variety - 1:3:6 proportion. |
| 15 | Hire and labour charges for shuttering with centering and necessary staging upto 4 m using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slabs, beams and columns, lintels curved or straight including fitting, fixing and striking out after completion of works. 25 mm to 30 mm thick wooden shuttering as per decision & direction of Engineer-In-Charge. |
| 16 | 25 mm to 30 mm shuttering without staging in foundation. |
| 17 | Reinforcement for reinforced concrete work in all sorts of structures including distribution bars, stirrups, binders etc. initial straightening and removal of loose rust (if necessary), cutting to requisite length, hooking and bending to correct shape, placing in proper position and binding with 16 gauge black annealed wire at every intersection, complete as per drawing and direction. For works in foundation, basement and upto roof of ground floor / upto 4 m. Tor steel.SAIL/TATA/RINL .In Ground Floor |
| 18 | M.S. structural works in columns, beams etc. with simple rolled structural members (e.g. joists, angle, channel sections conforming to IS:226, IS:808 & SP(6)-1964 connected to one another with bracket, gusSets, cleats as per design, direction of Engineer-in- charge complete including cutting to requisite shape and length, fabrication with necessary bolting, metal arc welding conforming to IS:816-1956 & IS:1995 using electrodes of approved make and brand conforming to IS:814-1957, haulage, hoisting and erection all complete. The rate includes the cost of rolled steel section, consumables such as electrodes, gas and hire charge of all tools and plants and labour required for the work including all incidental chages such as electricity charges, labour insurance charges etc. Payment to be made on the basis of calculated weight of structural members only in finished work as per IS specified weight. For structural members of specified sections weighing less than 22.5 kg/m may be increased allow for bracket, cleat, rivet, bolts and nuts etc. and no seperate payment being made for these items, as per direction of Engineer In Charge. The rates are considered for a height of erection 8m. / 2nd floor level from the ground. Add 1.5% extra over the rate for EA additional floor or 4m. beyond initial 8m. or part thereof. For structural members of specified sections weighing less than 22.5 Kg./m |
| 19 | M.S. or W.I. ornamental grill of approved design joints continuously welded with M.S.,W.I. flats and bars of windows, railing etc. fitted and fixed with necessary screws and lug in ground floor. Grill weighing above 10 Kg./sq.M and upto 16 Kg/Sq.M. a) Ground floor. |
| 20 | Plaster (to wall, floor, ceiling etc.) with sand and cement mortar,..With 1:6 cement mortar 20 mm thick plaster |
| 21 | Plaster (to wall, floor, ceiling etc.) with sand and cement mortar,..With 1:6 cement mortar 15 mm thick plaster |
| 22 | Plaster (to wall, floor, ceiling etc.) with sand and cement mortar,..With 1:4 cement mortar 10 mm thick plaster |
| 23 | Neat cement punning about 1.5 mm thick in wall, dado, window sill, floor etc. Note - Cement 0.152 CuM per 100 SqM. |
| 24 | Scraping of moss, blisters etc. thoroughly from exterior surface of walls necessitating the use of scraper, wire brush etc.(Payment against this item will be made only when this has been done on the specific direction of the Engineer-in-charge) |
| 25 | Applying Exterior grade Acrylic primer of approved quality and brand on plastered or cencrete surface old or new surface to receive decorative textured (matt finish) or smooth finish acrylic exterior emulsion paint including scraping and preparing the surface throughly, complete as per manufacturer\"s specification and as per direction of the EIC. One Coat. In Ground Floor |
| 26 | Exterior grade Acrylic primer, In First Floor |
| 27 | Exterior grade Acrylic primer, In Second Floor |
| 28 | Protective and Decorative Acrylic exterior emulsion paint of approved quality, as per manufacturer\"s specification and as per direction of EIC to be applied over acrylic primer as required. The rate includes cost of material, labour, scaffolding and all incidental charges but excluding the cost of primer. (Two Coats) Premium 100% Acrylic Emulsion. In Ground Floor |
| 29 | Protective and Decorative Acrylic exterior emulsion paint, In First Floor |
| 30 | Protective and Decorative Acrylic exterior emulsion paint, In Second Floor |
| 31 | Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc. |
| 32 | Priming one coat on timber or plastered surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc. |
| 33 | Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary : On steel or other metal surface - With super gloss (hi-gloss) - Two coats (with any shade except white) |
| 34 | On timber or plastered surface - With super gloss (hi-gloss) - Two coats (with any shade except white) |
| 35 | Removing old scales, blisters etc. of interior surface of walls,ceiling by scraping etc. and preparing smooth and even surface with rendering or cement mortar (1:2) (as necessary), to make the surface suitable for receiving distemper. (Payment against this item will be made only when this has been done on the specific direction of the Engineer-in-charge). |
| 36 | Rendering the surface of walls and ceiling with white cement based wall putty of approved make and brand (1.5 mm thick) |
| 37 | Applying Interior grade Acrylic Primer of approved quality and brand on plastered or cencrete surface old or new surface to receive Distemper/ Acrylic emulsion paint including scraping and preparing the surface throughly, complete as per manufacturer\"s specification and as per direction of the EIC. (In Ground Floor)One Coat. Water based interior grade Acrylic Primer |
| 38 | Applying Acrylic Emulsion Paint of approved make and brand on walls and ceiling including sand papering in intermediate coats including putty (to be done under specific instruction of Superintending Engineer) : (Two coats) Standard Quality |
| 39 | Supplying best Indian sheet glass panes set in putty and fitted and fixed with nails and putty complete. (In all floors for internal wall & upto 6m height for external wall) 3 mm thick (weighing 7.4 kg/Sq.m) |
| 40 | Renewing worn out putty of glass panes. Panes not exceeding 0.2 Sq.m |
| 41 | Cleaning and removing paint mark from glass pane with spirit and removing strains etc. |
| 42 | Labour for dismantling G.I./P.V.C/U.P.V.C pipe with fittings. 80mm to 100mm. |
| 43 | Refixing G.I./P.V.C/U.P.V.C pipe with fittings after cleaning where necessary. 80mm to 100mm. |
| 44 | Removing chokage in G.I./P.V.C/U.P.V.C pipe including cleaning pipe. 15mm to 25mm. |
| 45 | Supplying, fitting & fixing UPVC pipes A- Type and fittings conforming to IS:13592-1992 with all necessary clamps nails, including making holes in walls, floor etc. cutting trenches in any soil through masonry concrete structures etc. if necessary and mending good damages including joining with jointing materails (Spun Yarn, Valamoid / Bitumen / M-Seal etc.) complete. UPVC Pipes : 110 mm dia. |
| 46 | UPVC Fittings : Bend 87.5 degree 110 mm dia. |
| 47 | UPVC Fittings : Shoe 110 mm dia. |
| 48 | Supply of UPVC pipes (B Type) & fittings conforming to IS-13592-1992. Single Socketed 3 Meter Length. 75 mm |
| 49 | Fittings, Plain Tee, 75 mm |
| 50 | Fittings, Door Tee, 75 mm |
| 51 | Fittings, Vent Cowl, 75 mm |
| 52 | Fittings, Pipe Clip, 75 mm |
| 53 | Supplying, fitting and fixing bib cock or stop cock. Chromium plated Bib Cock short body (Equivalent to Code No. 511 & Model - Tropical / Sumthing Special of ESSCO or similar brand). |
| 54 | Polythene Bib Cock / Stop Cock (HD) with metal inlet (EMCO / ATLAS or equivalent) 15 mm |
| 55 | Chromium plated angular Stop Cock with wall flange (Equivalent to Code No. 5053 & Model - Florentine of Jaquar or similar brand). |
| 56 | Dismantling and refixing bib cock or stop cock. |
| 57 | Supplying, fitting and fixing 10 litre PVC low-down cistern conforming to IS specification with PVC fittings complete, CI brackets including two coats of painting to bracket etc. |
| 58 | Supplying,fitting and fixing approved brand P.V.C. CONNECTOR white flexible, with both ends coupling with heavy brass C.P. nut, 15 mm dia. 750 mm long. |
| 59 | Supplying,fitting and fixing approved brand 32 mm dia PVC waste pipe, with PVC coupling at one end fitted with necessary clamps. 900 mm long. |
| 60 | Supplying, fitting and fixing 32 mm dia Flush Pipe of approved make with necessary fixing materials and clamps complete. Polythene Flush Pipe. |
| 61 | Supplying, fitting and fixing bevelled edged mirror 5.5 mm thick silver red as per IS:3438-1965 together with brass CP hinges. 600 mm X 450 mm. |
| 62 | Supplying, fitting and fixing pillar cock of approved make. CP Pillar Cock - 15 mm (Equivalent to Code No. 507 & Model - Tropical / Sumthing Special of ESSCO or similar brand). |
| 63 | Supplying, fitting and fixing stainless steel sink complete with waste fittings and two coats of painting of C.I. brackets. Sink only 630 mm X 550 mm X 180 mm |
| 64 | Supplying, fitting and fixing white vitreous china best quality approved make wash basin with C.I. brackets on 75mm X 75mm wooden blocks, C.P. waste fittings of 32mm dia., one approved quality brass C.P. pillar cock of 15mm dia., C.P. chain with rubber plug of 30mm dia., approved quality P.V.C. waste pipe with C.P. nut 32 mm dia., 900mm long approvedquality P.V.C. connection pipe with heavy brass C.P. nut including mending good all damages and painting the brackets with two coats of approved paint. 550 mm X 400 mm size. |
| 65 | Supplying, fitting and fixing pedestal of approved make for wash basin (white) |
| 66 | Cleaning the concrete surface by removing dirt and debris, marking defective locations and removing loose concrete by careful stripping untill hard surface is exposed, cutting the concrete to regular shape, wire brushing the exposed surface and removing debris from site complete as per direction of the Engineer - in - Charge. |
| 67 | Supplying & laying 20 mm designer chequered tiles of any shade and of approved quality as per IS: 1237: 1980 laid in patterns as directed in pavement, footpath including necessary underlay 25 mm thick average cement mortar (1:3) complete in all respect with all labour and materials [using cement slurry @ 4.4 kg/Sq.m at back side of tiles. Cement of mortar & slurry will be supplied by the Department. Border concrete if necessary to be paid separately]. |
| 68 | Labour charge for fabrication and installation of composite door, window, partitions made from annodized extruded alloy aluminium sections for the following units: 2 track sliding window. |
| 69 | Labour charge for fabrication and installation of composite door, window, partitions made from annodized extruded alloy aluminium sections for the following units: 3 /4 track sliding window. |
| 70 | Labour charge for fabrication and installation of composite door, window, partition made from extruded alloy aluminium sections for the following units:- Partly glazed partly panelled or fully glazed single leaf alunminium swing door made of extruded and annodized alloy aluminium sections, fabrication including cutting to proper shape and size, drilling and aligning, fitted with heavy duty hydraulic action floor sping placed in the floor with mending damages,with top pin assembly of approve make and brand, fitted with in built locking arrangement, flush bolt, glazing clips and all other necessary fittings, fixtures, dhesives and joineries, cutting glass of approved make to requisite shape and size fitting with dry set neoprene or EPDM gasketing, cutting to requisite shape and size panel board (prelaminated particle block) fixing them with glazing clips as per drawing, specification and direction of Engineer in charge. |
| 71 | Labour charge for fabrication and installation of composite door, window, partition made from extruded alloy aluminium sections for the following units:- Partly glazed partly panelled or fully glazed double leaf alunminium swing door made of extruded and annodized alloy aluminium sections, fabrication including cutting to proper shape and size, drilling and aligning, fitted with heavy duty hydraulic action floor sping placed in the floor with mending damages,with top pin assembly of approve make and brand, fitted with in built locking arrangement, flush bolt, glazing clips and all other necessary fittings, fixtures, dhesives and joineries, cutting glass of approved make to requisite shape and size fitting with dry set neoprene or EPDM gasketing, cutting to requisite shape and size panel board (prelaminated particle block) fixing them with glazing clips as per drawing, specification and direction of Engineer in charge. |
| 72 | Supplying heavy duty hydraulic double action floor spring along with top pin / Set of pivots conforming to IS:6315 or any approved make as per direction of Engineer-in-charge. |
| 73 | Supplying bubble free float glass of approved make and brand conforming to IS: 2835-1987. 5mm thick coloured / tinted / smoke glass. |
| 74 | Supplying bubble free float glass of approved make and brand conforming to IS: 2835-1987. 5mm thick clear glass. |
| 75 | Door stopper. (Anodised aluminium) |
| 76 | Supplying PVC rollers for sliding windows as per direction of Engineer in charge. |
| 77 | Supplying maruti lock (100mm) |
| 78 | \" T\" shaped EPDM gasket for frames. |
| 79 | \"U\" shaped EPDM gasket for frames. |
| 80 | Weather gasket / wool pile for door vertical. |
| 81 | Supplying 4lever mortice lock or any approved make and brand as per direction of the Engineer- in -Charge. 100 mm. |
| 82 | Filling the gap in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over 6mm dia backer rod of approved quality as per architectural drawings and direction of Engineer-in-Charge complete.Upto 5 mm depth and 5 mm width. Ground Floor |
| 83 | 2- track sliding window, i) Bottom Frame |
| 84 | 2- track sliding window, ii) Top and side frame. |
| 85 | 3- track sliding window, i) Bottom Frame |
| 86 | 3- track sliding window, ii) Top and side frame. |
| 87 | Shutter for all track sliding window. i) Bottom & Top member. |
| 88 | Shutter for all track sliding window. ii) Style Side Member |
| 89 | Shutter for all track sliding window. iii) Interlock member. |
| 90 | Fixed glazing. i) Top, bottom and side member. |
| 91 | Fixed glazing. ii) Mullion. |
| 92 | Fixed glazing. iii) Glazing clip. |
| 93 | Fixed partitions.(Unsupported length of vertical member upto 1.5 m. Height of both ends of vertical member restrained but panels within 0.9 sqm.) Top , bottom & side member. |
| 94 | Intermediate member. |
| 95 | Glazing clip. |
| 96 | Fixed partitions. (Unsupported length of vertical member more than 1.5 Mor both ends of vertical member restrained but panels more than 0.9 Sq.m) Top , bottom & side member. |
| 97 | Intermediate member. |
| 98 | Glazing clip. |
| 99 | Door frame (Top & sides). |
| 100 | Shutter : Top rail. |
| 101 | Shutter : Bottom rail. |
| 102 | Shutter : Lock rail |
| 103 | Door vertical. |
| 104 | Glazing clip. |
| 105 | Supplying, Aluminium Grill with F channel frame of approved make and brand having ultimate tensile strength of 19 Kg/Sq.m. and modulus of elasticity 7000 kg/ sq.m., with 15 micron anodised fitted & fixed with necessary screws etc. complete as per direction of Engineer-in-charge. Grill made with 10 mm wide and 5.2 mm thick aluminium sheet having expansion width of 66.00 mm and weight not less than 3.26 Kg/Sq.m. |
| 106 | Hydraulic door closer of approved quality as per I.S.I. Standard fitted and fixed complete. Heavy type (I.S.I. size 3) |
| 107 | Supplying, fitting and fixing PVC pipes of approved make of Schedule 80 (medium duty) conforming to ASTMD - 1785 and threaded to match with GI Pipes as per IS : 1239 (Part - I). with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting pipes, making threads,fitting, fixing etc. complete in all respect including cost of all necessary fittings as required,jointing materials and two coats of painting with approved paint in any position above ground. (Payment will be made on the centre line measurements of total pipe line including all specials. No separate payment will be made for accesories, specials. Payment for painting will be made seperately) (a) For Exposed Work. 15 mm |
| 108 | PVC pipes of approved make, 20 mm |
| 109 | PVC pipes of approved make, 25 mm |
| 110 | PVC pipes of approved make, 32 mm |
| 111 | Supply of Chlorinated Polyvinyl Chloride (CPVC) pipes & fittings conforming to IS-15778: 2007, Ball Valve 15 mm |
| 112 | Supply of Chlorinated Polyvinyl Chloride (CPVC) pipes & fittings conforming to IS-15778: 2007, Ball Valve 25 mm |
| 113 | Iron butt hinges of approved quality fitted and fixed with steel screws, with ISI mark. 100mm. X 75mm. X 3.50mm |
| 114 | Iron hasp bolt of approved quality fitted and fixed complete (oxidised) with 16 mm dia rod with centre bolt and round fitting. 300 mm long. |
| 115 | Anodized aluminium barrel / tower / socket bolt (full covered) of approved manufactured from extruded section conforming to I.S. 204/74 fitted and fixed with cadmium plated screws. 100mm long x 10mm dia. bolt. |
| 116 | Anodised aluminium D-type handle of approved quality manufactured from extruded section conforming to IS specification (IS-230/72) fitted and fixed. With continuous plate base (Hexagonal/Round Rod) Grip 125 mm X 12 mm |
| 117 | Supplying, fitting and fixing Stainless Steel railing consist of 38mm dia and 900mm height vertical balustrade at every two alternative steps, 50mm dia top rail, 3 (three ) nos 19mm dia horizontal Strainless steel pipe and base/cover plate with Strainless Steel GRADE 304 containing 7.5% nickle (Interior Grade) Brushed/Mat finish, complete as per direction of the Engineer-incharge. Weight of Strainless Steel railing per M 6.5 Kg (approx) |
| 118 | Wall panelling / partition with Melamine faced 3 layered flat pressed wood particle board of approved make and brand as per direction of Engineer-in-Charge of requisite grade bonded with phenol formaldehyde synthetic resin conforming to IS:848-1974 (excluding the cost of supporting frame work and teak wood battens / lipping) In Ground Floor Prelaminated particle board conforming to IS:3087-1985 and IS:12823-1990. Both side decorative laminate Interior Grade 12 mm thick.In Ground Floor |
| 119 | Supplying fitting, fixing decorative lamination conforming to IS: 2046 : 1995 as per approved make, brand, finish and thickness with fitting, fixing the same on Particle/MDF / Ply Boards with recommended / approved adhesive with proper clipping the sides for better attachment as per direction of Engineer-incharge. The rate includes the cost of labour, adhesive and all incidental charges thereof.Glossy/Matt/Sue de excluding surface texture or metallic lustre. Thickness of laminate 1.5mm. In Ground floor |
| 120 | Supplying, fitting and fixing boiling water proof ply conforming to IS: 710-1977 bonded with phenol formaldehyde synthetic resin conforming to IS: 848-1974 of approved make and brand fitted and fixed as per design as per approval and direction of Engineer-in-Charge. [excluding the cost of supporting frame work and teak wood batten/Lipping]In Ground Floor, 19mm |
| 121 | Boiling water proof ply, 12mm |
| 122 | Boiling water proof ply, 4mm thick |
| 123 | Supplying, fitting & fixing of Telescopic Channel (Non-Schedule Item, rate collected from P.O. No. 4900007115, E.O no. RM/BDN/CIVIL/689) |
| 124 | Supplying, fitting and fixing Godrej Multi Lock or equivallent . |
| 125 | Taking out shutter of door and window, dismantling by parts (for repair or replacement of damaged parts), reassembling and refitting and rehanging same withold fittings but with new screws as necessary. |
| 126 | Easing and oiling, cleaning collapsible gate and repairing tolocking arrangements. |
| 127 | Easing and oiling, cleaning rolling shutters excluding repair toinside locks. |
| 128 | Cleaning wash basin/ sink with acid. |
| 129 | Cleaning E.P. or Anglo-Indian W.C. with acid. |
| 130 | Cleaning urinal with channel with acid. |
| 131 | Cleaning glazed tiles with acid. |
| 132 | Supplying PVC water storage tank of approved quality with closed top with lid (Black) - Multilayer - 1000 litre capacity . |
| 133 | Labour for hoisting plastic water storage tank. Upto 1500 litre capacity. Upto 1st story from G.L. |
| 134 | Labour for lowering plastic water storage tank and stacking in places as directed. Upto 1500 litre capacity. From 1st floor to G.L. |
| 135 | Labour for punching hole in plastic water storage tank upto 50 mm dia. |
| 136 | Supply of galvanised iron jamnut. 25 mm |
| 137 | Supplying, Fitting & Fixing Factory made P.V.C. door frame of size 50 mmx47 mm with a wall thickness of 5 mm, made out of extruded 5 mm, PVC sheet miter cut at two corners and joined with two nos of 1.5 mm long brackets of 15 mm x15 mm M.S. square tube. The two vertical door profiles are to be reinforced with 19 mmx 19 mm M.S. Square tube of 19 gauge, weather seal to be provided through out the frame. The door frame shall be fixed with the wall using 65/100 mm long M.S. Screws through the frame by using P.V.C fasteners. A minimum of 4 Nos of screws to be provided for EA vertical member and minimum 2 Nos for horizontal member etc. complete as per Manufacturer\"s specification and direction of Engineer-in-Charge. |
| 138 | PVC Door Shutter-30 mm thick: Supplying fitting and fixing P.V.C. door shutter of approved quality & shade in position, the style & rail of the P.V.C. door shutter will be made of rigid P.V.C. multicavity hollow chamber of 59 mm x30 mm section with 2.0 mm (+/-0.2 mm) wall thickness.Horizontal & vertical section shall be fixed to EA other by self tapping screws and 1 solid polymeric or M.S. galvanised tubular \"L\" shaped bracket 100mm x 200mm in EA corner of the shutter frame for placing hinges. Polymer based multicavity hollow section of 120 mm x30mm with 2.0 mm (+/- 0.2 mm) wall thickness will be fitted in the middle, reinforced by solid polymer bar of 200 mm long at both ends and screws from both sides as lock rail. The section frame will then be fitted in by PVC panels of size 100 mmx25 mm with wall thickness of 1.2 mm (+/- 0.2 mm) and 2 nos. of 6 mm dia bright rod will be inserted horizontally with both side check and nut system and stretches where fixing of hinges / hasp bolt / tower bolt / door ring are required to be strong enough to with stand wear and tear. The rate is inclusive of cost of all materials, labour, and hire of tools and plants and appliancesi/c carriage of all materials taxes and all other incidental charges complete. |
| 139 | Supplying, fitting & fixing 1st quality Ceramic tiles in wallsand floors to match with the existing work & 4nos. of keystones (10mm) fixed with araldite at the back of each tile &finishing the joints with white cement mixed with colouringoxide if required to match the colour of tiles includingrougheningof concrete surface, if necessaryorby syntheticadhesive & grout materials etc. Floor. With Sand Cement Mortar (1:4) 20mm thick & 2mm thick cement slurry at back side of tiles using [email protected]/Sq.m & joint filling using white cement slurry @0.20kg/Sq.m. Area of each tile upto 0.09 Sq.m. Coloured decorative. |
| 140 | Supplying, fitting & fixing 1st quality Ceramic tiles in wallsand floors to match with the existing work & 4nos. of keystones (10mm) fixed with araldite at the back of each tile &finishing the joints with white cement mixed with colouring oxide if required to match the colour of tiles includingroughening of concrete surface, if necessary or by syntheticadhesive & grout materials etc. Wall. With Sand Cement Mortar (1:3) 15mm thick & 2mm thick cement slurry at back side of tiles using cement @2.91Kg/Sq.m & joint filling using white cement slurry @0.20kg/Sq.m. Area of each tile upto 0.09 Sq.m. Coloured decorative |
| 141 | Labour for setting tiles in floor/pavement in cement mortar(1: 4) joints finished with white cement. |
| 142 | Polishing only of old marble or terrazo work with oxalic acidpowder using 33 gms/ sq.m. bymanual labour / machinewhere necessary. |
| 143 | Washing and cleaning with oxalic acid powder using 33gms./sq.m. Marble floor/ marble dado |
| 144 | Washing and cleaning with oxalic acid powder using 33gms./sq.m. Floor/ dado other than marble |
| 145 | Supplying, fitting and fixing glass reinforced polyester translu cent fiber glass sheet to match with GCI Corrugation as per IS: 12866 - 1989 in roof fitted and fixed with 10 mm dia \"J\" or \"L\" hook, bolts and nuts, limpet and bitumen washers and putty with 150mm end lap and one corrugation minimum side lap complete. 1.6mm +/- 0.2 mm thicksheet.(2.6Kg/Sq.m) i) Natural white or tinted blue colour |
| 146 | Removal of rubbish, earth etc. from the working site and disposal of the same beyond the compound, in conformity with the Municipal / Corporation Rules for such disposal, loading into truck and cleaning the site in all respect as per direction of Engineer in charge. Please Enable Macros to View BoQ information |
