|
| 1 | Repair to potholes of any depthn exc 1 sqm each incl sweeping free from dust and mud or water, scoring sunken surfaces in roads path etc. cutting around edges to at least 25 mm depth, making good by filling in scrolled and graded road metal, watering and well raming incl supply of road metal making good by applying tack coat @ 5 Kg per 10 sqm putting in premixed bituminous macadam,well rammed and sealed with binder 9.8 kg per 10 Sqm with 0.09 Cum of stone chipping,6.3 mm size and again well rammed (including supply of premixed macadam,binder and chippings), depth of pot holes Exc 30 mm complete all as specified and directed. |
| 2 | M& L for emergent repairing of potholes of Avgthickness 20 mm to 75 mm and stiches on the existing road surface top priority using ready mix cold mix bituminous (CRRI) approved in 50 kg bags including cleaning,filling and compaction as per IRC: 116 and open to traffice after 10 minutes Complete all as specified and directed. |
| 3 | Applying evenly a priming coat with mechanical sprayer over old black top surfaces with paving bitumen VG-10 @ 10 kg per 10 sq metrecomplete all as specified and directed. |
| 4 | Applying evenly a priming/tack coat with mechanical sprayer over old black top surfaces with paving bitumen VG-10 @ 2.5 kg per 10 sq metre complete all as specified and directed. |
| 5 | M&L for preparing of black top surfaces by brushing with wire brushes for removing caked mud etc sweeping with broom & finally fanningthe cleaned surfaces with gunny bag to remove all loose dirt etc complete all as specified and directed. |
| 6 | Material & Labour for 30 mm thick (consolidated average thickness) bituminous premix asphaltic semi dense concerete with 5 % binder (of pavingbitumen VG-30) content by weight of total mix, rolled & compacted with 08 to 10 tonne power road roller to required camber and gradient complete all as specified and directed (Laying of bituminous premix asphaltic semi dense concrete with mechanical paver) complete all as specified and directed. |
| 7 | M&L for premixed bituminous macadam using paving bitumen of VG-30 grade with binder content 4% by weight of total mix and complacted to required gradient and camber laid by mechanical paver (consolidated thickness 75 mm or less) with 8 to 10 tonne power vibrator road roller etc complete all as specified and directed. |
| 8 | S&F in repair ofcat eye solar reflective type of metal body alloy of size 100 mm x 100 mmx20 mm with PAMA striplens reflector of modelNo DA 972.0 fixed with and incl MS stud of suitable size as per manufacturers instructions.Complete all as specified and directed. |
| 9 | M&L for preparing Bituminous surfaces of road and marking 2.5 mm thick centre lines,stop lines,dashes,arrows etc and the like n. exc 10 cm wide on roads pavements with hot applied thermoplastic road marking paint of approved colour confirming to BS machine all as per manufacturer\"s instructions & colour as directed by GE complete all as specified and directed. |
| 10 | Supply and fixing in repair metal tubular dealineator made out of ABS round body fitted with 2 Nos 65 mm dia highly reflective reflectors made out of PMMA and mounted on 45/50 mm dia mild steel pipe of 600 mm height duly powder coated and thermo plastic elastomer 3 bands of green, red and yellow reflector radium tape of 25 mm wide strips with anti theft steel net for reflector protection including embedding in PCC 1:2:4(150x150x300mm) type B1 complete all as specified and directed. |
| 11 | Demolition of cement concrete (unreinforced) in ground floors and pavings n.exc 15cm thickness (below or above ground level) complete all as specified and directed. |
| 12 | M&L for Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and directed. |
| 13 | M&Lfor Cement concrete1:2:4 Type B-1 (using 20mm graded stone aggregate) as in Coping, bands, bed plates,etc including necessary form workcomplete all as specified & directed |
| 14 | M&L two coats of synthetic enamel paintof approved colour over a coat of primer on new concrete /kerb surfaces stone including prepartion of surfaces complete all as specified and directed. |
| 15 | S & F in repair plastic speed bump is designed so dynamically and compact that it can bear maximum load on it.the body of the running speed bump is made of PE material.two highly reflective reflectors molded in PMMA material are welded with PE base plate through ultrasonic welding process and then fixed on to the speed bump so that dust and water cannot touch reflector\"s inside are andthus it maintains its reflectivity for a long time.it is available in yellow and black colours.Dimensions : length -750 mm,width-250 mm,height-75 mm,weight and load capacity upto 100 ton complete all as specified and directed. |
| 16 | S & F in repair with stainless steel frame of 50 mm dia and 1.8 mm thicknessof Stainless steel pipe for framing of Sign board including cutting,welding and framing of stainless steel structure including necessary clamps etc Retro-reflective,double sided,road name,Sign boards comprising of 4 mm thick aluminium Composite panel,(ACP) mill finished or PDVF coated or as specified as base board,micro prismatic retro reflective sheet and electro cut coloured overlay film.the ACP shall have thickness of 4 mm with 0.5mm thick skin of aluminium on both sides.the ACP shall be routed,folded and fixed on the stainless steel frame with VHB tape,24 mm wide and 2.3 mm thick provided through out the length and breath of the frame including riveting at the right angle more than 300 mm center to center ensuring that no riveting is seen on either face of the frame.on the front and backface of the ACP,Microprismatic retroreflective sheet Conforming to type XI of IRC:67:2012 shall be presurre fixed as background sheet which will be over laid with electro cut transparent film of approved make and colour to create a desired road name information message including grouting in PCC 1:2:4 type B-0 (using 12.5 mm graded stone aggregate ) of size 0.3x0.3x0.45 m below ground level Complete all as specified and directed.Note: Rate shall be deemed to be included all materials, labour, Equipments,fabrication,cutting and welding and any other specific type of work is required for preparation of sign board |
| 17 | S& Fin repair of convex mirror 80 CM in size out door purpose including stand/pedestal embedded in PCC block 1:2:4 type B-1 size 45 X 45X 45 CM and including necessary earth work complete all as directed. |
