|
| 1 | Excavating over areas, not exceeding 1.5 m deep, and getting out in soft/loose soil, including trimming sides, levelling bottom, dressing and ramming of bed, complete all as specified and directed |
| 2 | Returning, filling in and around foundations including spreading, watering and ramming in layers not exceeding 150 mm thick, complete all as specified and directed. |
| 3 | M & L for Cement concrete (1:4:8), type D-2, using 40 mm graded stone aggregate, in foundations, filling and mass concrete, including mixing, laying, ramming, finishing fair and even, curing complete, complete all as specified and directed. |
| 4 | Demolition of brick work or stone/boulder masonry, built in cement mortar incl. all quoins arches, pillars etc. but excluding ashlar facing, dressed stone work andprecast concrete articles, complete all as specified and directed. |
| 5 | M & L for brickwork with old serviceable bricks obtained from dismantling/demolition, straight or curved on plan exceeding 6 metres mean radius, built in cement mortar (1:6), complete all as specified and directed. |
| 6 | M & L for Brickwork with subclass ‘B’ bricks, straight or curved on plan exceeding 6 metres mean radius, built in cement mortar (1:6), complete all as specified and directedNote:-The rates for brickwork shall be deemed to include all rough cutting and waste in brickwork, cutting and pinning in mortar as for adjacent work, and preparation of tops and sides of existing walls for raising, extending and bonding new brick masonry, including formation of toothing and making good, complete all as specified and directed. |
| 7 | Taking down cement plaster including raking out joints hacking for key and scrubbing down with water complete as specified and directed. |
| 8 | M&L for 15mm thickrendering in CM 1:4 on other than fair faces of brick or concrete surfaces finished even and smooth without using extra cementall as spfd and directed. |
| 9 | M & L for Reinforced cement concrete 1:1.5:3 using 20 mm graded aggregate Slabs supported on walls,beams and the like items complete all as specified and directed. |
| 10 | M&L TMT steel bars 6mm to 8mm dia and over cut to length bent shape required, including cranking bending binding with mild steel wire (annealed) not less than 0.9mm dia quality conforming to relevant IS complete all as specified. |
| 11 | M & L for Formwork to soffits of suspended slabs such as roof slabs, floorslabs, landings and similar work to provide smooth finish; not exceeding 200mm thick (Horizontal or sloping) complete all as specified. |
| 12 | M&L for preparation of new plastered surface of walls and applying two coat of exterior weather proof water base emulsion paint (APEX) of any color complete all as specified & directed.Note:- Quoted rate shall be deemed to be included for work in buildings/structure upto 15mtr height. |
| 13 | Taking down or up 15 mm bore galvanised iron tubing and connection including cleaning for refixing or removal all as specified |
| 14 | Providing and fixing CPVC pipes upto 20 mm outer dia conforming to IS 15778 Class 1 (SDR 11) or Class 2 (SDR 13.5) for hot and cold water supply, complete with all plain CPVC fittings (elbows, tees, sockets, reducers, couplings, end caps,) without metal inserts, solvent welded using one-step yellow CPVC solvent cement or two-step CPVC primer + cement , properly cut and grooved where specified for mechanical couplings, including Cutting chases in brick, stone, concrete block or slab wall pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills,sunshades, shelves, lintels, etc.; and cutting chases for concealed watertubing or concealed conduit wiring,etc., and making good, cutting not exc 10 cm girth, securing with CPVC saddles/clips at 1m centres (max 1.5m), true to line and level with minimum 50mm cover from finished wall surface, including cutting, threading/grooving, jointing, and proper testing for any water leakage complete all as specified and directed by Engr in charge. |
| 15 | Supplying brass threaded CPVC fittings upto 20 mm outer dia (FTA - Female Threaded Adaptor, MTA - Male Threaded Adaptor, Brass Elbows, Brass Tees, Unions, Ball Valves, Flanges, Tank Adaptors etc) conforming to ASTM F437/F438/F439 with metal inserts, for connection to taps, showers, fixtures, storage tanks, complete with CPVC solvent cement jointing on pipe side and threaded brass connection complete all as specified and directed by Engr in charge. |
| 16 | S & F 500 ltrs Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top )including dismantling the old storage tank andhoisted and fixed in position etc completeall as per specified and directed. |
| 17 | S & Fin repair 20 mm bore ball brass valves (Float valve) high pressure with polythene float and fly nut complete screwed to iron pipe or brass ferrule complete all as specified |
| 18 | S & F 100 mm dia cast iron soil waste and vent pipes sand cast in any length with or without laid in trenches or in floor with cement joints complete all as specified |
| 19 | Dismantling of cast iron drain pipe of 75/100mm bore jointed in lead joints or cement joints and taking out of under floors if required |
| 20 | S&F for 75 mm bore Cast iron soil, waste and vent pipes in anylength with or withoutears, with cementjoints, laid in trenches or in floors icomplete all as specified. |
| 21 | S&F for 75 mm bore cast iron drain drain/waste/vent pipes fixed to wall, floor jointed with lead joints incl dismantling of old cast iron drain,waste, vent pipe of any description , jointed with any material . |
| 22 | S & F cast iron floor trap with graating of 75 mm size including jointing to waste pipe with cement joints etc complete as directed |
| 23 | S & F cast iron floor trap with graating of 100 mm size including jointing to waste pipe with cement joints etc complete as directed |
| 24 | S&F in repair ofCast iron branch pieces , tee equal or unequal spigot or socket type or with parallel branches to 100 mm dia pipe fitted with access door complete all as specified by Engineer-in -Charge . |
| 25 | S&F in repair ofCast iron branch pieces , tee equal or unequal spigot or socket type or with parallel branches to 75 mm dia pipe fitted with access door complete all as specified by Engineer-in -Charge . |
| 26 | M&L for ceramic coloured tiles as in floors 7 to 8 mm thick(square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 Sqm (400mmx400mm x 7mm thick) set and jointed in neat cement slurry and pointed in colour cement as in floorover and including 15 mm thick screed bed or bedding layer ofcement mortar (1:6) including dismantling floor and screeding etc complete all as specified. complete all as specified and as directed. |
| 27 | S&F for glazed ceramic coloured tiles 7mm thick 450 x 300mm size in vertical surface set and jointed in neat cement slurry and pointed in white cement paste pigmented to the shade. Etc including 10 mm thick rendering in CM 1:4 including dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off tfrom the permission of MoD land complete all as specified. |
| 28 | S&F in repairvitreous china wash basin, white, flat back, size 550 mm x 400 mm fixed on and including cast iron cantilever bracket 32 mm dia brass waste coupling and including fixing of tap, waste fitting and union complete all as specified and as directed. |
| 29 | Supply and fixed in repair 15 mm dia bore pillar taps cast copper alloy, with capstan heads, chromium plated, screwed down high pressure with or without lettered ‘Hot’ or “cold’ with long screwed shank and flynuts, screwed for iron pipe and fixed complete all as specified and as directed. |
| 30 | Material and fixing vitreous china urinal, bowl type (back wall or corner wall type), complete with PTMT urinal spreader of approved colour, minimum weight 60 gms, connected to 15 mm dia GI/CPVC water pipe through PTMT connection fittings (minimum weight 32–45 gms), including bedding the urinal against wall in cement mortar 1:2, providing and fixing wall plugs and securing urinal with 60 mm long brass screws, pointing around the back of urinal in cement complete with brackets, flush pipe, grating and union for discharge pipe, all as specified and as directed |
| 31 | S&F 32 mm bore of pipe low density (LDPE) of pressure rating 6 kg/ sqcm fixed to wall or floor etc including fittings complete all as specified and as directed. |
| 32 | Material and fixing 32 mm waste fitting for urinal, brass, chromium plated, with long screwed shank and fly-nut, suitable for vitreous china urinals, including bedding flange end in red lead cement and fixing the other end to waste pipe complete, all as specified and as directed |
| 33 | S&F in repair vitreous china squatting pan “ORISSA PATTERN” size 580mmx440mm ‘white’ with integral foot rest (excluding flushing cistern and flush pipe) including connection to trap and to flushing pipe anti syphonage pipe etc complete all as specified and as directed. NOTE:- Old dismantled IWC should be thrown outside MoD land. |
| 34 | S & F in repair PVC low level cistern of 10 ltrs capacity with top push buttion inclusive of brackets and PVC bend long type and connecting to flush pipe of any size and pattern with inlet ball valve float and handle complete all as specified and directed. |
| 35 | S&F in repair Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified. |
| 36 | S&F in repair bib tapof CPfancy type with butterfly handle screwed down screwed for iron pipe of 15mm bore complete all as specified and as directed |
| 37 | Taking down chowkats or frame with shutter (without taking out shutter from the frame) exceeding 1.50 sqm and n exc 4.00 sqm each and removal from site all as specified and directed |
| 38 | S & F for factory made solid PVC door frame of size 50mm x 47mm made out of 5mm prelaminate PVC sheet, reinforced with MS square tube fixed in opening with smooth finish complete as per manufacturer\"s specifications and as directed by Engineer-in-Charge |
| 39 | S & F Factory Made Solid PVC Moulded Door Shutter with particle board, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing specified in SSR andas directed by Engineer-inCharge |
| 40 | S&F, 100 mm long butt hinges, extruded alminium alloy with galavanised mild steel hinge pin, anodised and fixed , type C-21 |
| 41 | S&F 150 mm size aluminium handles, cast type anodised and fixed. |
| 42 | S&F 150 mm long aluminum, anodised,barrel tower bolts of extruded section and fixed. |
| 43 | S&F in repair of (600mm x 450mm) bevelled edge mirror of selected quality glass mounted on 6mm thick AC building board or commercial plywood with aluminium frame 15 x 15 and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified. |
| 44 | S&F in repair of CP soap tray fixed to walls with rubber plugs complete all as specified and directed. |
| 45 | S&F in repair brass chromium plated tubular towel rail 20 mm dia D type, 60 cm long between flanges complete all as specified and as directed. |
| 46 | S & F in repair PVC connection 15 mm size with CP nuts of length 600 mm etccomplete all as specified. |
| 47 | S&F angle valves CP screwed down high pressureof fancy type chromium plated screwed both ends for iron pipe or for union and fixed with 15mm bore in repairs |
| 48 | M & L for rendering 5 mm thick on ceiling on fair faces ofbrick or concrete surface in CM (1:3) finished even and smooth without using extra cement all as specified |
| 49 | M & L preparation of newly plastered surfaces and applying two coats of distemper oil emulsion with one coat of putty incl preparation of surfaces. |
| 50 | S&F of factory-made 18 mm thick single-extruded WPC solid plain white colour board Jali, CNC (Computer Numeric Control) routed to approved design and pattern and machine cut to required shapes and sizes for duct/shaft covering, partitions and facades, manufactured from virgin polymer of K-Value 58–60 (suspension grade), calcium carbonate and natural fibres (wood powder/rice husk/wheat husk) with non-toxic additives (maximum toxicity index 12 per 100 gms), having minimum density 650 kg/cum, screw withdrawal strength 1800 N (face), compressive strength 50 N/mm², modulus of elasticity 850 N/mm² and resistance to spread of flame Class ‘A’ category, being termite/borer proof, water/moisture proof and fire-retardant, fixed on MS framework made of 25×25×1.5 mm square hollow sections including intermediate MS square/rectangular hollow sections between two jali panels for proper welding, rigidity and alignment and MS angle sections 25×25×3 mm at free/exposed edges, panel junctions and around openings for edge protection and stiffness, complete with all welding, grinding and finishing, the MS framework being placed at 1.00 m × 1.00 m grid or as directed including making holes in existing RCC/brick masonry walls/floors for anchoring MS members and packing with PCC (1:2:4), providing and applying one coat of approved steel primer and two coats of enamel paint to all MS members, fixing WPC jali with stainless steel screws and fasteners, including all materials, labour, tools, plant, scaffolding and incidental works complete as directed by Engineer-in-Charge; only solid single-extruded WPC boards shall be used and hollow or co-extruded boards shall not be permitted, minimum thickness after CNC routing shall not be less than 12 mm at any point and make of WPC board shall be approved by GE. |
| 51 | M & L preparation of old painted surface of steel and iron work of any description over 10 cm width or girth and applying one coat of synthetic enamel paint etc complete all as specified and as directed. |
| 52 | Supply and laying ,XLPE insulated PVC sheathed, armoured,heavy duty, aluminium conductor electric cable 1100 Volt gradeof4 core10 Sqmm in duct/floor/wall with provision of saddle and lugs, etc including taking down of old one, all as specified and as directed. |
| 53 | Excavation in trenches not exceeding 1.5 metre wide and not exceeding 1.5 metre depth and getting out in soft / loose soil for laying of cable all as specified and directed by the Engr-in-Charge. |
| 54 | Removing excavated soil to a distance not exceeding 50 metre anddepositing where directed at a level, not exceeding 1.5 metre above the starting point complete all as specified and directed by the Engr-in-Charge |
| 55 | Material and labour forfilling dry river sand as cushioning for under ground cables complete all as specified and as directed by the Engr-in-Charge.(Note :for the Measurentpurpose only punned thicknes shall be measured & paid) |
| 56 | Material and labour for common burnt clay building bricks sub-class \"B\" designation of size230X115X75mm complete all as specified and directed |
| 57 | S&F Bollard light fitting including pole and post top light new generation, energy saving, environmental friendly, long life aesthetically designed die-cast aluminium landscape luminaires for downward lighting with high power LED as light source with epoxy powder coated black after phosphochromeate treatement of 12 Watt capacity, height 920mm and width 185mm ,IP65 protectionall as specified and directed. |
| 58 | S&F Bollard light fitting 10 watt inverted pyramid tripod type, energy saving, environmental friendly, long life aesthetically designed die-cast aluminium landscape luminaires for downward lighting with high power LED as light source with epoxy powder coated black after phosphochromeate treatement height 813mm and width 180mm ,IP65 protectionall as specified and directed. |
| 59 | Supply and laying High density poly ethylene pipes (HDPE) 25 mm dia of pressure rating 6 kgf/cm2 fixed complete to walls, ceilings or in floors etc. all as spedified and directed |
