|
| 1 | Items: |
| 2 | Providing and erecting Approved make Three pole moulded case circuit breaker having breaking capacity ICU of 25 K.A. at 415 V having normal current rating up to25 A to 100A. with Fixed thermal & magnetic release suitable to work on A.C. supply 50 c/s. with all internal connections, spreader tinned copper & complete erected in existing 16 G.M.S. housing.ICS=100% of ICU only |
| 3 | Providing and erecting busbar chamber confirming to IS-375 fabricated from 16 G.M.S. sheet, dust & vermin proof having hinged door with rubber gasket and necessary busbar supports with COPPER busbar having current density not more than 1.6 Amp. / sq.mm (Rated current / cross section area) duly wrapped with colour insulation tape for phase sequence, three phase & neutral each suitable for following current capacity with necessary painting mounted on wall or pedestal frame of required size with necessaryconnections. (A) Suitable for 63/100 Amp. capacity |
| 4 | (C) Suitable for 300 Amp. capacity |
| 5 | Providing and erecting Approved make Three pole moulded case circuit breaker having breaking capacity/strength ICU of 50 K.A.and above at 415V. having normal current rating250A. with variable thermal & magnetic release suitable to work on A.C.supply 50 c/s. with all internal connections, spreader tinned copper & complete erected in existing 16 G.M.S. housing. ICS=100% of ICU only |
| 6 | Supply of Approved make Iron Clad or metal clad four pole change over switch 415V. confirming to ISof following capacity (A)200 A / 250 A |
| 7 | Providing and erecting Sheet Steel powder coated MCB distribution board - flush / surface mounted fitted with busbar, neutral link, earth bar and DIN rail, Conforms to IS 8623-1 & 3, IEC 61439-1 & 3 without MCB to house appropriate nos. of MCBs.(The DBs should be used of same company of MCB to be used) suitable for(A) single phase incoming and horizontal single phase outgoing (b) sheet steel double door (IP-43)(iii)8 way |
| 8 | (B) three phase incoming and single phase horizontal type outgoingPer phase isolation type (PPI)(b) sheet steel double door(ii)6 way |
| 9 | providing and erecting Miniature circuit breaker single pole 6A to 25A suitable to operate on 240 V A.C. system and having breaking capacity10 KA to be erected in existing box. confirming to IS 8828/1996 with ISI Mark |
| 10 | Providing & erecting 240 V MCB double pole switch for motor & inductive load(C Curve) having 10 KA breaking capacity & confirms to IS : 8828 in existing box having following capacity (A) 6 to 32 Amp. |
| 11 | providing and erecting Mains with ISI marked, 1.5KV grade electrolyte multi stranded, annealed copper conductor with heat resistant PVC insulated conforms to IS 694, IEC - 227 erected in existing pipe offollowing size (Specifically for control panel, relays, power switchgears, motor starters & control wiring) with required size of copper lugs, nuts and bolts if required. (e) One wire 6.00 sq. mm |
| 12 | (g) One wire 16.00 sq. mm |
| 13 | Solder less crimping type Copper lugs conforming to IS suitable for cable of following size evenly crimped with high pressure tool & connected to switchgear terminals with brass/cadmium plated nut bolts in an approved manner. (C) 16 Sq.mm. |
| 14 | Providing & erecting 415 V MCB three Polefor Motor & InductiveLoad (C Curve) having 10KA breaking capacity & confirms to IS :8828 in existing box having following capacity (c)63 Amp. |
| 15 | Supplying and erecting LED street light / Flood light fittings with High power White LEDs wattage of 3 Watt and above assembled on single MCPCB, efficiency more than 130 lm/w and corrosion free High pressure die cast aluminum housing with smooth finish powder coated and heat sink extruded aluminium with diffuser and Polycarbonate optics/ lenses, with toughened glasswith company mark/name engraved or embossed 160 to 270 V,Power Factor more than 0.95, THD < 10 %, CCT3000 K to 5700K,Uniformity ratio >0.45, Luminaire efficacy> 100 lumens/watt . LED driver efficiency > 85 %.(fittings required LM-79 & LM-80 certificates)(NOTE: Below description have shown ranges of Wattage capacity of LED fittings.The Engineer incharge may select any wattage capacity between the ranges shown.) (A) Street Light (IP-65), Surge protection -4KV integral and ,Light must have 440VAC line supply with over-voltage protection.(iv) above 90 to 120 watts |
| 16 | (B) Flood Light (IP-65),Surge protection -4KV integral and ,Light must have 440VAC line supply with over-voltage protection. (vi) above 160 to 200 watts |
| 17 | Supplying & erecting XLPE(IS:7098)(I)-88 ISI unarmoured copper cable 1.1 KV grade to be erected as directed of following size. (E)3 core 2.5 Sq. mm |
| 18 | Providing & erecting PVC Corrugated Flexible Conduit with required nos. of coupling, PVC bushes, Check-nuts etc. complete of following sizes.(2) 25 mm |
| 19 | (5) 50 mm |
| 20 | Supplying & erecting earth pit of minimum bore dia.150mm size approved make Earthing Electrode consisting Pipe-in-Pipe Technology as per IS 3043-1987 made of corrosion free hot dipped G.I.Pipeshaving Outer pipedia of 50mm having 80-200 Micron galvanising, Inner pipe dia of 25 mm having 200-250 Micron galvanising, connection terminal dia of 12mm with constant ohmic value surrounded by highly conductive compound with high charge dissipation suitable for following type of applications with chamber and heavy duty cover.(approvedmake OEM has to submit test certificate) & having back filling compound of (B)Inner chemical (CCM Compound)- Resistivity:- 0.2 / meter testing as per IEC 62561-2017, Voltage drop:- < 1 volt at no load & dry form, Sulphar content:- <2%(C) Back fill Compound:- Earthing compound should be capable to retain moisture for long timeNecessary test report must be submitted. (b)For Electrical installation up to 11 KV in normal soil.Length of Pipe : 2.00 mtrsBack filling Compound :1 no. Bag |
| 21 | Providing and erecting Annealed bare Copper wire 8 to 16 SWG. |
| 22 | Supplying and erecting Direct - On - Line Starter with 18 A. rating contactor and with 3.5 Amp. 18A range directly operated in totally insulated elegant enclosure for single phase operation up to 3 HP as per IS 13947 complete erected on P.W. Block with necessary connection. |
| 23 | Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 0.5 Watt assembled on single MCPCB,with housing used as a heat sink shall be made of thick sheet Steel conforming to IS: 513/CRCA/aluminium pressure die castpowder coated and high U.V. & corrosion resistancewith diffuserhoused in aluminium casted body with company mark/name 160V to 270V,Power Factor more than 0.9, THD < 15 %,CCT3000 K to 6500K, Luminaire efficacy> 85 lumens/watt ,LED driver efficiency > 85 %( fitting required LM-79 & LM-80 Certificates)(NOTE: Below description have shown ranges of Wattage capacity of LED fittings.The Engineer incharge may select any wattage capacity between the ranges shown.)(A) Square/ Circular shaped Surface/Recessed Mount Downlight with provision for spring loaded mounting clips complete.IP20(iv) 22-24 watts, Surge-2 KV |
| 24 | (B) LED Panel Light with provision for Plane front frame with translucent cover fixed to housing complete.IP20(vii) from 45 to 48 watts, 24\" x 24\", Surge-2 KV |
| 25 | Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 0.5 Watt assembled on single MCPCB,with housing used as a heat sink shall be made of thick sheet Steel conforming to IS: 513/CRCA/ aluminium die castpowder coated and high U.V. & corrosion resistancewith diffuserwith company mark/name 160V to 270V, Power Factor more than 0.9, THD < 15%,CCT3000 K to 6500K, Luminaire efficacy> 85 lumens/watt ,LED LED driver efficiency > 85 %( fitting required LM-79 & LM-80 Certificates)(NOTE: Below description have shown ranges of Wattage capacity of LED fittings.The Engineer incharge may select any wattage capacity between the ranges shown.)(A) Tube Light with integral driver (v) 36-40 Watts, Surge-2 KV, IP-20, conventional 4 feet |
| 26 | Supplying and erecting led lamps with following wattage capacity of 220 to 240 voltage, minimum 15000 burning hours life, 500 V in built-surge protection,Polycarbonate diffuser, mounting suitable for E14 / E27 / B22 lamp holders, pf >= 0.5(A) LED Lamps integral type, with PC diffuser suitableLAMP holder (ii)5 to 8 watts |
| 27 | Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Aluminium conductor for1.1 KV. to be laidon wall with necessary clamps or in existing trench/ pipe of following size of cables (F) 3 1/2core 120 Sq. mm ( 70 Sq. mm 1/2 core) |
| 28 | providing and erecting Mains with ISI marked, 1.5KV grade electrolyte multi stranded, annealed copper conductor with heat resistant PVC insulated conforms to IS 694, IEC - 227 erected in existing pipe offollowing size (Specifically for control panel, relays, power switchgears, motor starters & control wiring) with required size of copper lugs, nuts and bolts if required. (j)One wire 50.00 sq. mm |
| 29 | Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand / SolidCopperconductor for1.1 KV. to be laidon wall with necessary clamps or in existingtrench/ pipe at road crossing or floorof followingsize of cables. (A) 4 core 2.5 Sq. mm |
| 30 | Supplying & erectingapproved makeSMC press moulded composite FRP.loop-in, loop-out approx. 2mm thick box complete with Bakelite connector strip 5way(3P+N+E),DIN rail for mounting mob& hinged doors as per requirement having locking arrangements with mounting clamp with nuts, bolts & washers suitable for erection on pole with cable clamps& earth bolt of following size of box. (G) 250mm x 220mm x 135mm[deep] |
| 31 | Supplying & erecting XLPE(IS:7098) (I)-88 ISI unarmoured Aluminium cable 1.1 KV.grade to be erected as directed of following size. (D) 2 core 10 Sq. mm |
| 32 | Providing & erecting Approved make Ceiling Fan with double ball bearing ISI mark with Condenser 230 volt A.C.50 Hz1200 mm sweep complete having 3 blades aluminium body and blade sets having ornamental design shanks , canopyerected with earthing.[ Make shall be approved by Engineer in Charge] |
| 33 | Supplyingand erecting approved make online Un-interruptible Power Supply system comprising flat cum-boost charger, static Inverter & sealed maintenance free SMF batteries. The charger having operating capacity for input 160-270V AC &inverter having output230V,50 Hz Acwith 0.8 load power factor with battery, over/under voltage output with over load & short circuit protection equipment. The system housed in CRC sheet duly powder coated paint with following power backup.with MS painted batteries stand, 10% Overload capacity for momentary load. (A) 1 KVA with 1Hr Backup |
| 34 | Providing following type of Modular Type Accessories mounted with PVC / metallic/Wooden box, single mounting base frame covered with textured / metallic/white front plate , modules erectedwith necessary connections as per site situation directed by Engineer In charge.(1)One No. SP 6 Amp. |
| 35 | (2) One No 5 pin plug |
| 36 | (5) Electronic hum Freesteps EME Fan regulator |
| 37 | (9) 16 Amp. SP one way switch |
| 38 | (10) 6/16Amp. Universal socket |
| 39 | Supply & fixing of 4.5KG GAS type Co2 (ISI marked) extinguisher including all accessories with wall bracket & raw plug conforming to IS:15683 as directed by Engineer in Charge |
| 40 | Removel & Disconnect old Mains & Old Distribution Box And Mains Controls, Cable saddling etc. |
| 41 | MCC Panel power Coating done by 7 tank process with of 14/16 gauge CRCA sheet with 250 Amp MCCB With 200Amp C/O Switch Amf meter ct coil, alluminum busbar . And relay panel also included M.S stand base &Dual Starter & Star delta starter. Folded channel totally enclosed Cubical type with pad lock arrangement complete in all repect as per details or as approved by the Engineer in Charges. Panel should be as per detailed single line Diagram with required nos of incoming and outgoing feeders and accessories complete in all respect. |
