|
| 1 | ALMIRAH LARGE /MEDIUM STEEL WITH SHELVES |
| 2 | Replacement of old existing broken / unserviceable locks of any description and in any position with new locks, six lever with double keys , fixing with suitable nuts including repair of locking device , complete all as specified and directed by Engineer-in-Charge,Make:Godrej/Harrison |
| 3 | Replacement of old existing broken / unserviceable door handles of Almirahwith new door handle of size 100mm long, cast Iron chromium platedof approved make and shall be fixedwith suitable nuts and pins,complete all as specified and directed by Engineer-in-Charge . |
| 4 | Replacement of old existing broken / unserviceable Legs of Almirahwith new Legs made out of1.0mm mild steelsheet including welding of legswhere as required,complete all shown in drgandas directed by Engineer-in-Charge . |
| 5 | Taking out unserviceable steel clamp with new steel clamp made out of MS sheet 3.00mm thick of size 50mmx20mm including fixing of loose shelves, complete all as specified and as directed by Engineer-in-Charge. |
| 6 | Replacement of old damaged/ unserviceable shelves of Almirah large with newshelf 1.0mm thick Mild Steel Sheet of size 0.765mx0.44mwith suitable clamps as shown in drgto be painted with two coat ofsynthetic enamel paint (Olive green) over a coat of red oxide primer with spray gun stove enamel paint,finish to the required shade , complete all as shown in drg and as directed by Engineer-in-Charge |
| 7 | Replacement of old damaged/ UNSV shelves of Almirah Medium with new 1.0mm thick Mild Steel Sheet of size 0.765mx0.44mwith suitable clamps as shown in drg and to be painted with 02 coats of synthetic enamel paint (Olive green) over a coat of red oxide primer with spray gun stove enamel paint, finish to the required shade , complete all as shown in drg and as directed by Engineer-in-Charge |
| 8 | Replacement of unserviceable locking device from Almirah large/Medium steel with new locking device, complete all as shown in drg and as directed by Engineer-in-Charge |
| 9 | BED PLYWOOD TOP |
| 10 | Replacement of unserviceable/demaged long rail from Bed with ply top with new long rail made of sheesham seasoned, hard wood size 1980mm x90mmx35mm matching with existing shape and size, complete all as specified and directedby Engineer-in-Charge. |
| 11 | Replacement of unserviceable/demaged headboard with new headboard of size 0.90mm x0.46m made of ply wood commercial, 4.0mm thick and one side teak faced, duly covered with 4mm thick teak wood beading all around, complete all asshown in drg and as specified and directedby Engineer-in-Charge. |
| 12 | Replacement of unserviceable/demaged footboard from Bed with ply top with new footboard made of ply wood commercial, 3.5mm thick and one side teak faced, duly covered with 4mm thick teak wood beading all around, complete all asshown in drg and as specified and directedby Engineer-in-Charge. |
| 13 | Replacement of unserviceable legs from Bed with ply top with new legs made of seasoned hard wood complete all asshown in drg and as specified and directedby Engineer-in-Charge. |
| 14 | Replacement of unserviceable plywood and stiffener from Bed with ply top with new ply wood top commedrcial, 12mm thick of size 0.90m x1.98m, exterior grade BWR including hardwood stiffener provided at bottom of ply wood, complete all asshown in drg and as specified and directedby Engineer-in-Charge. |
| 15 | CHAIR CB STEEL WITH ARMSFD-75 |
| 16 | Materials and labour for welding to damaged/decayed steel frame of chair CB steel with arms complete all as directed by Engineer-in-Charge. |
| 17 | Supply and fixing 15mmx3mm flat iron of length 0.49m to bottom of steel frame in support of wooden seat frame duly welded to steel frame as specified and as directed by Engineer-in-Charge |
| 18 | Taking out old damaged/decayed arms rest from its position and supply and fixing new arm rest made out of size 0.05mx0.030m x 0.42m well seasoned teak wood and fix in the same position with new screws as per existing shape and size complete all as specified and as shown on drgand as directed by Engineer-in-Charge. |
| 19 | Taking out old damaged/decayed seat frame from its position supply and fixing new seat frame made of well seasoned teak wood duly weaving with new plastic cane white colour half round (oval type) 2mm wide and 4mm wide complete all as specified and as shown on drg and as directed by Engineer-in-Charge. |
| 20 | All as per item ser No 3.04 here in before but back frame of chair CB steel with arms. |
| 21 | Taking out old unserviceable top cap from its position and supply and fixing new plastic top cap best quality in the same posn complete all as directed by Engineer-in-Charge. |
| 22 | Materials and labour for painting frame of chair CB steel with arms with one coat of olive green synthetic enamel paint after preparation of steel surfaces complete all as specified and as directed by engr-in-charge. |
| 23 | Materials and lobour for polishing to seat/back and hand rest with black French polish glossy finish after preparation of wooden surfaces complete as specified and as directed by Engineer-in-Charge. |
| 24 | CHAIR TUBULAR STEEL WITHOUT ARMS FD-75 |
| 25 | Materials and labour for welding to damaged/decayed steel frame of chair CB steel without arms complete all as directed by Engineer-in-Charge. |
| 26 | Supply and fixing 15mmx3mm length 0.41mflat iron to bottom of steel frame in support of wooden seat frame duly welded to steel frame all as specified and as directed by Engineer-in-Charge. |
| 27 | Taking out old damaged/decayed seat frame from its positoin supply and fixing new seat frame made of well seasoned teak wood of size with total length 1.60m x 0.025m thick and 0.035m wide dulyweavingwith new plastic cane white colour half round (oval type) 2mm wide and 4mmwidecomplete all as specified and as shown on drg. |
| 28 | All as per item ser No 4.03 here in before but back frame of chair CB steel without arms. |
| 29 | Taking out old unserviceable top cap from its position and supply and fixing new plastic top cap best quality in the same posn complete all as directed by Engineer-in-Charge. |
| 30 | Materials and labour for painting frame of chair CB steel without arms with one coat of olive green synthetic enamel paint after preparation of steel old surfaces complete all as specified and as directed. |
| 31 | Materials and lobour for polishing to seat and back black French polish glossy finish after preparation of wooden surfaces complete as specified and as directed by Engineer-in-Charge. |
| 32 | CHAIR WRITING |
| 33 | Replacement of old unserviceable/damaged rear leg from chair writing with new legs made of seasoned teak wood matching with the existing shape and size, complete all as shown in drawing and as directed by Engineer-in-Charge. |
| 34 | Replacement of old unserviceable/damaged front leg from chair writting with newlegs made out of well seasoned second class teak wood matching with the existing shape and size 0.685mx0.030mx0.055m, complete all as shown in drawing and as directed by Engineer-in-Charge. |
| 35 | Replacement of old unserviceable /damaged front/back/side rail from chair writing with new front/back/side rail made out of well seasoned teak wood of size 0.535mx0.025mx0.020m matching with the extsting shape and size, complete all as shown in drawing and as directed by Engineer-in-Charge. |
| 36 | Replacement of old unserviceable/damaged stiffeners from chair writing with new stiffeners made of seasoned teak wood size 0.535mx0.025mx0.020m matching with the existing shape and size, complete all as shown in drawing and as directed by Engineer-in-Charge. |
| 37 | Replacement of old unserviceable/damaged hand rest from chair writing with new hand rest made of seasoned teak wood of size 0.535mx0.025mx0.020m matching with the existing shape and size, complete all as shown in drawing and as directed by Engineer-in-Charge. |
| 38 | Recanning of chair writing with 2.0 mm wide, half round white plastic cane and perimeter canning with 4.0 mm cane including supply of new cane, complete all as shown in drawing and as directed by Engineer-in-Charge. |
| 39 | Polish of best quality to the chair writing including preparation of surface, complete all as shown in drawing and as directed by Engineer-in-Charge. |
| 40 | CHAIR CBA SPL WITH HAND REST |
| 41 | Materials and labour for welding to damaged/decayed steel frame of chair CBA spl with hand rest steelwithhand rest complete all as directed by Engineer-in-Charge. |
| 42 | Taking out old damaged/decayed hand rest from its position and supply and fixing new hand rest madeof pre laminated particle board one size 0.075mx0.055m x 190mm and fix in the same position with new screws as per existing shape and size complete all as specified and as shown on drgand as directed by Engineer-in-Charge. |
| 43 | Taking out old damaged/decayed front seat frame from its positoin supply and fixing new seat frame made of well seasoned teak wood of size with total length 1.40m x 0.020m thick and 0.030m wide dulyweavingwith new plastic cane white colour half round (oval type) 2mm wide and 4mmwide complete all as specified and as shown on drg. |
| 44 | All as per item ser No 6.03 here in before but back frame of chair CBA steel with hand rest. |
| 45 | Materials and labour for painting frame of chair CBA splwith hand rest with one coat of olive black synthetic enamel paint after preparation of steel old surfaces complete all as specified and as directed. |
| 46 | Materials and lobour for polishing to seat and back black French polish glossy finish after preparation of wooden surfaces complete as specified and as directed by Engineer-in-Charge. |
| 47 | CHAIR EXECUTIVE WITH CUSHION AND ARMS (VISITOR) TP |
| 48 | Replacement of old unserviceable Seat and Backfrom chair executive with new seat & back made out of ply wood & foam cushion coverr with superior crap fabric in Hans Pattern shall be fixed on the froma with 08 Nos steel screw and washers of adequate size as per sample,complete allas directed. |
| 49 | Replacement of old Plastic Arms (PP Arms) from chair with new PlasticArms (PP) fixed with 02 Nos Nuts and washers, complete all as specified anddirected. |
| 50 | Material and labour for welding to damaged/broken flat iron 25mm x 6mm thick length 0.48m duty welded beeath the seat froma shallbe painted two coat of synthetic enamel paint (black colour) including preparation of steel surface all as directed. |
| 51 | CHAIR EXECUTIVE REVOLVING (TP) |
| 52 | Replacement of old unserviceable base stand of Chair Executive Revolving of any type and supply and Fixing new base stand of chair revolving complete with hydraulic system, fixed all as shown on drawing and as directed. |
| 53 | Replacement of Tapestry cloth from Seat and back of chairs with new tapestry cloth of approved quality and shade including replacement of foam cusion of density 40 kg/Cum 100 mm thick 6mm thick pressed and plywood of size 530mmx470mm etc as required including painting repair, welding and re-adjustment of chair as per trade pattern ,complete allas directed. |
| 54 | Replacement of old unserviceable Hand Rest from chair (Excutive) with new hand rest of size 700mmx50mmx20mm of different type as per trade patter4n matching with existing hand rest ,complete allas directed. |
| 55 | Replacement of old unserviceable twin wheel castor froma chair executive with new twin wheel costors as per sample complete allas directed. |
| 56 | CHAIR DINING |
| 57 | Replacement of unserviceable rear leg from chair dining with new rear leg of seasoned teak wood of size 0.89mx0.030mx0.055m matching with the existing shape and size, complete all as specified and directed by Engineer-in-Charge. |
| 58 | Replacement of unserviceable front leg from chair dining with new front leg of seasoned teak wood of size 0.46mx0.080m x 0.055m from chair dinning with new front leg of seasoned teak wood matching with the existing shape and size, complete all as specified and directed by Engineer-in-Charge. |
| 59 | Replacement of unserviceable front/back/side rail from chair dining with new front/back/side rail made out of well seasoned teak wood of size 0.430m x 0.030mx0.065m matching with the existing shape & Size, complete all as specified and directed by Engineer-in-Charge. |
| 60 | Replacement of unserviceable stiffeners from chair dining with new stiffeners made of size 0.44mx0.025mx0.020m made out of well seasoned teak wood matching with the existing shape & size, complete all as specified and directed by Engineer-in-Charge. |
| 61 | Re-canning of chair dining arms with 2 mm wide half round white plastic cane and perimeter canning with 4 mm cane as shown in drawing including supply of new cane as required, complete all as specified and directed by Engineer-in-Charge. |
| 62 | Replacement ofseat cushion of chair dinning Map with new seat cushion of foamdensity of32 Kg/cum, 100 mm thick of size 510 mm x480 mm covered with tapestry cloth as directed by Engr -in-Charge. |
| 63 | French polish of best quality to the chair dining with arms including preparation of surface complete all as specified and directed by Engineer-in-Charge. |
| 64 | CHAIR DINING WITH LONG BACK |
| 65 | Replacement of unserviceable rear leg from chair dining with new rear leg of seasoned teak wood of size 0.80mx0.035mx0.055m matching with the existing shape and size, complete all as specified and directed by Engineer-in-Charge. |
| 66 | Replacement of unserviceable front leg from chair dining long back with new front leg of seasoned teak wood of size 0.50mx0.025mx0.055m from chair dinning long back with new front leg of seasoned teak wood matching with the existing shape and size, complete all as specified and directed by Engineer-in-Charge. |
| 67 | Replacement of unserviceable stiffeners from chair dining long back with new stiffeners made of size 0.40mx0.025mx0.020m made out of well seasoned teak wood matching with the existing shape & size, complete all as specified and directed by Engineer-in-Charge. |
| 68 | Replacement ofseat cushion of chair chair dining long back with new seat cushion of foamdensity of20 Kg/cum, 50 mm thick of size 483 mm x432 ncluding polishing repair etc, as directed by Engr -in-Charge. |
| 69 | CHAIR WOODEN BOTTOM WITHOUT ARMS |
| 70 | Replacement of old unserviceable/damaged rear leg from chair wooden bottom with new legs made of seasoned teak wood matching with the existing shape and size, complete all as shown in drawing and as directed by Engineer-in-Charge. |
| 71 | Replacement of old unserviceable/damaged front leg from chairwooden bottom with newlegs made out of well seasoned second class teak wood matching with the existing shape and size 0.685mx0.030mx0.055m, complete all as shown in drawing and as directed by Engineer-in-Charge. |
| 72 | Replacement of old unserviceable /damaged front/back/side rail from chair wooden bottom with new front/back/side rail made out of well seasoned teak wood of size 0.535mx0.025mx0.020m matching with the extsting shape and size, complete all as shown in drawing and as directed by Engineer-in-Charge. |
| 73 | Replacement of old unserviceable/damaged stiffeners from chair wooden bottom with new stiffeners made of seasoned teak wood size 0.535mx0.025mx0.020m matching with the existing shape and size, complete all as shown in drawing and as directed by Engineer-in-Charge. |
| 74 | Replacement ofseatof chair wooden bottom with new seatof 12mm BWR Grade plywood size 440 mm x430 mm fixed with secrews with all as directed by Engr -in-Charge. |
| 75 | CHARPOY NIWAR |
| 76 | Taking out existing unserviceable cotton newar from the charpoy newar, supply & fixing with 12 mm thick Plywood commercial of size 1980x900, exterior grade BWR including hardwood stiffener provided at bottom of ply wood, complete all as shown in drg and as specified and directed by Engineer-in Charge. |
| 77 | CHARPOY IP WITH HARD TOP |
| 78 | Replacement of unserviceable/damaged plywood top from its position with new plywood top of size 1930x960, X 12mm thick BWR grade (unpolished) fixed to CR frame with 38mm Long , 8 Gauge secrew self tapping hardened sheet matle , complete all as specified and directed by the Engineer-in-Charge. |
| 79 | SLEEPING BUNK COMPLETE 1850 x 945MM WITH STEEL FRAME (SINGLE BUNK) |
| 80 | Replacement of unserviceable/damaged plywood top from its position with new plywood top 1850mmx945mmx12mm thick, BWR grade including 20mmx25mm teak wood beading shall be provided in all sides at bottom of the plywood and one stiffener of size 20x25mm shall be provided in middle at bottom as shown in drawing, complete all as specified and ddirected by the Engineer-in-Charge. |
| 81 | CHARPOY GI PIPE DOUBLE BUNK |
| 82 | Replacement of unserviceable/damaged plywood top from its position with new plywood top 1850mmx945mmx12mm thick, BWR grade including 20mmx25mm teak wood beading shall be provided in all sides at bottom of the plywood and one stiffener of size 20x25mm shall be provided in middle at bottom as shown in drawing, complete all as specified and ddirected by the Engineer-in-Charge. |
| 83 | PEG TABLE |
| 84 | Replacementof old unserviceable /damaged top of table peg with new top made of pre-laminated particle board of size 0.45m x 0.30m one side teak face exterior grade BWR 18mm thick duly covered with 4mm thick teak woodbeading all around the top complete all as shown in drg and as directed by Engineer-in-Charge. |
| 85 | Polish of best quality to the peg table including preparation of surface with sand paper, complete all as directed. |
| 86 | PAINTING OF STEEL FURNITUREPainting of following steel furniture itemsby providing two coats of synthetic enameled paint of OG/Black/Smoke Gray to match with existing shade with spray gun after properly smoothing the surface with sand paper and applying putty and primer including minor welding/denting etc where necessary all as directed by Engineer-in-charge. |
| 87 | Rack adjustable steel closed type 900mmx1875mmx500mm having 6 shelves |
| 88 | Rack adjustable steel 6 tier (3 sides close) |
| 89 | Rack adjustablesteel 3 tier (3 sides close) |
| 90 | Rack folding 460mmx300mmx120mm |
| 91 | Almiraha large (Steel)with Shelves |
| 92 | Almiraha Med (steel) with Shelves |
| 93 | Steel locker of size 830x480x1900MM (Locker Bed side steel large) |
| 94 | Trestle store room steel |
| 95 | Rack steel with tray (FD-97 & 1023) |
| 96 | Rack steel with out tray (FD-97(M) |
| 97 | Sleeping bunk double 1890x800x1730mm |
| 98 | Table office with three drawerof size 1200x600x18mm (Steel) |
| 99 | Table office ClkSteelof size steel 1800x900x750mm |
| 100 | Locker bed side Steel |
| 101 | Locker bed side large steel of size 1620X595X520mm with one hapsstaple andone handle |
| 102 | Rack Store / Double Bunk Complete Size 1655x1950mm, 1855x1935mm |
| 103 | Box Kit steel |
| 104 | Rack laundry |
| 105 | Rack Pigeon with hole |
| 106 | Stool Steel of size 305x305x510mm |
| 107 | Table cook Steel |
| 108 | Table with drawer (Steel) 900x600x760mm |
| 109 | Table with out drawer (Steel) 900x600x760mm |
| 110 | Table office clerk (Type-I) 1500x750x750` |
| 111 | Desk Steel |
| 112 | Form with Back |
| 113 | SAFE MEAT AND MILK : FD-47 |
| 114 | Replacement of unserviceable marble top of size 900x600mm and old wire mesh from safe meat and milk with new marble top 18mm thick and new wire mesh of 1 mm mesh and of 20 gauge. Including unserviceable hasp and staples, handles with new 75mm long Aluminum hasp and staple, 100 mm long aluminum handle including repair and readjustment. Revolving all scratches and filling with putty and painting with two coats synthetic enamel white paint of approved quality on internal and external surface, complete all as specified and directed by Engineer-in-Charge. |
| 115 | TABLE COMPOSITE OFFICE OFFICER STEEL OF SIZE 1800X900X760MM |
| 116 | Repair to table office officer steel including dismantling/removal of all broken parts and replacing with new parts. Table top shall be pre laminated particle board 18mm thick of size 1.22mx0.61m exterior grade in natural teak shade and other side white with PVC beading edging all around.Drawer shall be repaired and should be smoothly functioning. All steel surface of table shall be painted with two coats synthetic enamel paint of existing shade with spray gun after properly smoothening the surface with sand paper and applying putty and primer where necessary. Hard rubber PVC shoe (04 Nos) shall be provided for legs complete all as specified and directed by Engineer-in-Charge. |
| 117 | TABLECOMPOSITE OFFICE CLERK STEEL1800X900X750MM |
| 118 | Repair to table office clerk steel including dismantling/removal of all broken parts and replacing with new parts. Table top shall be pre laminated particle board 18mm thick of size 1.22mx0.61m exterior grade in natural teak shade and other side white with PVC beading edging all around.Drawer shall be repaired and should be smoothly functioning. All steel surface of table shall be painted with two coats synthetic enamel paint of existing shade with spray gun after properly smoothening the surface with sand paper and applying putty and primer where necessary. Hard rubber PVC shoe (04 Nos) shall be provided for legs complete all as specified and directed by Engineer-in-Charge. |
| 119 | TABLE DINING OR FD-165 |
| 120 | Repair to table dinning ORs including dismantling/ removal of unserviceable existing top. New top shall be of 18mm thickparticle boardcommercial BWR duly coveredwith 24G aluminium sheet. Top shall be fixed on the frame with steel screws. Steel frame of the table shall be painted with two coats of synthetic enameled paint over one of the pink primer,complete all asspecifiedand directed by Engineer-in-Charge. |
| 121 | Replacement of UNSV Rubber shoe from legs of table dining ORsand fixed with new Rubber shoe of best quality, matching with existing shoe, complete all as specified anddirected by Engineer-in-Charge. |
| 122 | TABLE WRITING |
| 123 | Replacement of unserviceable top from table writing with new top made of pre-laminated particle board of size 1.145mx0.60m with one side teak face exterior, grade BWR, 18mm thick, duly covered with 4mm thick teak wood beading all around, complete all as shown in drawing and as directed by Engineer-in-Charge. Make:Kit ply/National/Bhutan/Nova pan. |
| 124 | Replacement of unserviceable leg from table writing with new leg made of seasoned teak wood size 0.76m length and 0.045m x0.045m at top and 0.025mx0.025m at bottom matching with the existing shape and size, complete all as shown in drawing and as directed by Engineer-in-Charge. |
| 125 | Replacement of unserviceable front/back rail from table writing with new front/back rail made of seasoned teak wood of matching with existing shape & size 1.145mx0.025mx0.050m, complete all as shown in drawing and as directed by Engineer-in-Charge. |
| 126 | Replacement of unserviceable centre stiffener from table writing with new centre stiffener made of seasoned teak wood of size 0.45mx0.615m, complete all as shown in drawing and as directed by Engineer-in-Charge. |
| 127 | Replacement of unserviceable back plywood from box of table writing with new back plywood made of 6mm thick, commercial, exterior, grade BWR, complete all as shown in drawing and as directed by Engineer-in-Charge. |
| 128 | Replacement of unserviceable shutters from table writing with new shutters made of pre-laminated particle board 18mm thick, grade BWR, one side teak faced, duly covered 4mm thick teak wood beading all around the shutters including piano type hinges, knob and six lever brass lock with duplicate keys of best quality, complete all as shown in drawing and as directed by Engineer-in-Charge. |
| 129 | Replacement of unserviceable drawers from table writing with new drawers made of 12mm thick teak wood, except bottom of drawers which shall be of 6mm thick plywood, comercial exterior, grade BWR including knob etc, complete all as shown in drawing and as directed by Engineer-in-Charge. |
| 130 | Polish of best quality to the table writing including preparation of surface with sand paper, complete all as shown in drawing and as directed by Engineer-in-Charge. |
| 131 | TABLE 900X600X760MM WITH DRAWER (STEEL) |
| 132 | Repair to table 900x600x760 without including dismantling/removal of of all broken parts and replacing with new parts. Top of table shall be 18mm thick particle board commercial BWR of size 1.22mx0.61m exterior grade in natural teak shade and other side white with PVCedging all around.Drawer shall be repaired and should besmothly function. All steel surface of table shall be painted with two coats synthetic enamel paint of edisting shade with spray gun after properly smothening the surface with sand paper and applying putty and primer where necessary. hard rubber PVC shoe (04 Nos) shall be provided to legs, complete all as directed. |
| 133 | TABLE 900X600X760MM WITHOUT DRAWER (STEEL) |
| 134 | Repair to table 900x600x760mm without including dismantling/removal of UNSV existing top. Top of table shall be 18mm thick particle board commercial BWR of size 1.22mx0.61m exterior grade in natural teak shade and other side white with PVC beading edging all around. All steel surface of table shall be painted with two coats synthetic enamel paint of existing shade with spray gun after properly smothening the surface with sand paper and applying putty and primer where necessary. hard rubber PVC shoe (04 Nos) shall be provided to legs, complete all as directed. |
| 135 | TABLE OFFICE WITH THREE DRAWERS CLERK OF SIZE 1200X600X18MM (STEEL) |
| 136 | Repair to table office with three drawers clerk steel by dismantling /removal all broken parts and replacing with new parts.The table top shall be prelaminated particleboard 18mm thick exterior grade in natural teak shade and other site white with 4mm thick PVC edging all around. Drawer shall be repaired and should be smothly function. All steel surface of table shall be painted with two coats synthetic enamel paint of existing shade with spray gun after properly smothening the surface with sand paper and applying putty and primer where necessary. hard rubber PVC shoe (04 Nos) shall be provided to legs, complete all as directed. |
| 137 | TEAPOY WOODEN |
| 138 | Replacement of old unserviceable top from Teapoy wooden with new top made of pre-laminated particle board, one side teak faced, exterior grade BWR, 18 mm thick, duly covered with 4mm thick teak wood beading all around thetop, complete all as shown in drawing and as directred by Enigneer-in-Charge. |
| 139 | Replacement of old unserviceable/demaged legs from teapoy wooden with new legs made of seasoned teak wood including rubber shoe at the bottom of legs, matching with the existing shape and size, complete all as shown in drawing and as directed by Engineer-in -Charge. |
| 140 | Replacement of old unserviceable/demaged front/back rail from teapoy wooden with new front/back rails made of seasoned teak wood matching with existing shape and size, complete all as shown in drawing and as directed by Engineer-in-Charge. |
| 141 | Wooden polish of best quality to the teapoy wooden including preparationof surface, complete all as shown in drawing and as directed by Eningeer-in-Charge. |
| 142 | CHAIR EASY& CHAIR EASY CUSHIONED Repair to Chair easy including removal of all broken parts and replacing with new parts and replacing with new parts of well seasoned first class hard wood teak duly French polished as under :- |
| 143 | Supply and fix rear legs of size as per drg No FD-229 |
| 144 | Supply and fix front legs of size as per drg No FD-229 |
| 145 | Supply and fix front and rear rail of size as per drg No FD-229 |
| 146 | Supply and fix side rail of size as per drg No FD-229 |
| 147 | Supply and fix stiffeners of size as per drg No FD-229 |
| 148 | Supply and fix arm rest of size as per drg No FD-229 |
| 149 | Re-canning of chair easy with 2.0 mm wide, half round white plastic cane and perimeter canning with 4.0 mm cane including supply of new cane, complete all as shown in drawing and as directed by Engineer-in-Charge |
| 150 | Replacement ofseat cushion of chair easy with new seat cushion of foamdensity of40 Kg/cum, 100 mm thick of size 510 mm x480 mm covered with high quality colured as directed by Engr -in-Charge. |
| 151 | Supply and and fixhard rubber ring/PCS toes to bottom of legs with screws, complete all as specified and directed by Engineer -in- charge |
| 152 | French polish of best quality to the chair easy and chair easy cushionedincluding preparation of surface complete all as specified and directed by Engineer-in-Charge. |
| 153 | CHAIR VERANDAH |
| 154 | Materials and labour for painting of chair verandah with one coat of white synthetic enamel paint after preparation of steel old surfaces complete all as specified and as directed by Engineer-in-Charge. |
| 155 | Re-canning of chair verandah with white plastic cane and perimeter as shown in drawing including supply of new cane as required, complete all as specified and directed by Engineer-in-Charge. |
| 156 | STEEL LOCKER OF SIZE 830X480X1900MM (TP) MADE OF SHEET TWO DOOR WITH TWO HANDLES |
| 157 | Replacement of old existing broken/Un-serviceable locks of any description and in any position with New locks, 6 lever with double keys, fixing with suitable nuts including repair of locking divice complete all as specified and directed by Engineer -in-Charge. |
| 158 | Replacement of old existing broken/Un-serviceable door handle of steel locker 100 mm long Cast Iron chromium plated of approved make, with nuts & pins, complete all as specified and directed by Engineer -in-Charge |
| 159 | Replacement of old existing broken / unserviceable Legs of steel locker and with Legs made out of1.0mm mild steelsheet including welding of legswhere as required,complete all shown in drgandas directed by Engineer-in-Charge . |
| 160 | Replacement of old existing broken/Un-serviceable looking mirror from its position with new morror of 5mm thickness and size 700x280mm, complete all as specified and directed by Engineer -in-Charge,. |
| 161 | RACK STEEL 6 TIER (FD-1039/ 103/1038) |
| 162 | Supply and fixing of shelves made of 1mm thick PBI sheet made to shape as per drg and directed by Engr-in- charge. |
| 163 | Cleaning & preparing surface for Gas welding of the broken of any steel furniture.Welding shall be done in best trade practice and running welding upto 100 mm shall be treated one point all as specified and directed.by Engineer-in-charge. |
| 164 | Supply and fixing of nuts and bolts of shelves to fix with angle iron where required as per drg and directed by Engr-in- charge. |
| 165 | RACK STORE / DOUBLE BUNK COMPLETE SIZE 1655x1950mm, 1855x1935mm |
| 166 | Replacement of unserviceable/demaged plywood top from its position with new plywood top 1655x1950mm, 1855x1935mm X 12mm thick, BWR grade including 20mmx25mm teak wood beading shall be provided in all sides at bottom of the plywood and one stiffener of size 20x25mm shall be provided in middle at bottom as shown in drawing, complete all as specified and ddirected by the Engineer-in-Charge. |
| 167 | SOFA SET FIVE SEATER |
| 168 | M&L for replacement of unserviceable cushion with new seat cushion of foamdensity of32 Kg/cum, 100 mm thick x 530 mm x 560 mm covered with tapestry cloth colored directed by Engr -in-Charge Make : Sleepwell/Kurlon |
| 169 | Polish of best quality to the sofa set five seater including preparation of surface with sand paper, complete all as directed. |
| 170 | CHARPOY GI PIPE |
| 171 | Replacement of unserviceable/demaged plywood top from its position with new plywood top of size 1980mm x 900mm x12mm thick, BWR grade fixed with 10 Nos of nuts, bolts and washer to GI frame as shown in drawing, complete all as specified and directed by lthe Engineer-in-Charge. |
| 172 | Removal of existing broken long rails from charpoy GI Pipe including cutting and threading the same into one short rail and one leg, and fixing the same inthe existing GI charpoy as required complete all as specified and directed by Engineer-in-Charge. |
| 173 | Removal of existing broken short rails of GI pipe charpoy includingcutting and threading the same into one leg and fixing in the same position , complete all as specified and directed by Engineer-in-Charge. |
| 174 | Replacement of unserviceable/ broken /old hexagonal check nut of size with 32 mm andfixed with 32 bore mm hexagonal check nuts where as required complete all as specified and directed by Engineer-in-Charge. |
| 175 | Replacement of existing broken/ unserviceable GI Elbow , from the GI charpoy with new 32mm bore,three way Elbow, wherever is required including necessary threading complete all as specified and directed by Engineer-in-Charge. |
| 176 | Supply and fixing leg of GI pipe made out of short rail retrieved under Serial item No 30.3 above duly threaded to require size fitted to the frame, complete all as specified and directed by Engineer-in-Charge. |
| 177 | DESK STEEL |
| 178 | Repair to desk steel including dismantling/ removal of UNSV existing top. Top shall be 18mm thickparticle boardcommercial BWR dulyfixed on the frame with steel screws with PVCedging all around. Steel frame of the desk steel shall be painted with two coats of synthetic enameled paint over one of the pink primer,complete all asspecifiedand directed by Engineer-in-Charge. |
