|
| 1 | M&L for preparation of old surfaces (plastered or unplastered) of walls including cornices, pilasters etc including brooming or steel wire brushing, scrapping down smoke soot, moulds, moss, efflorescent salts, trading oil, greasy spots and applying one coat of white wash complete all as specified & as directed.Note : The quoted rate shall be deemed to be included use of scaffoldings, trestles, ladders, cradles etc, necessary for execution of work and protective measures of any height. |
| 2 | M&L for preparation of old surfaces (plastered or unplastered) of ceilings including brooming or steel wire brushing, scrapping down smoke soot, moulds, moss, efflorescent salts, trading oil, greasy spots and applying one coat of white wash complete all as specified & as directed.Note : The quoted rate shall be deemed to be included use of scaffoldings, trestles, ladders, cradles etc, necessary for execution of work and protective measures of any height. |
| 3 | M&L for preparationof old surfaces (plastered or unplastered) of walls including removing/scrapping down existing surface where ever necessary and applying two coat of oil bound distemper (OBD) white or approved tinted including removing existing nails, if any and filling the disturbed /uneven surface, holes/voids with wall care putty1.0 mm thick to achieve the smooth surface complete all as specified & directed. |
| 4 | M&L for complete removal of old treatment by mechanical meansfrom wallsand applying one coatofprimer, 1 mm wall putty & sandingonplastered surfaces prepatatory to distempering and applying two coats of oil emulsion distemper white or tinted by pump roller applicatoras directed by Engineer-in-Charge |
| 5 | M&L for preparationof old surfaces (plastered or unplastered) of walls including removing/scrapping down existing surface where ever necessary and applying one coat (finish coat) of oil bound distemper (OBD) white or approved tinted including removing existing nails, if any and filling the disturbed /uneven surface, holes/voids with wall care putty to achieve the smooth surface complete all as specified & directed. |
| 6 | M&L for preparation of old painted steel and iron surfaces of any description over 10 cm in width or girth and applying one coat of synthetic enamel paint of approved tint all as specified & as directed. |
| 7 | M&L for preparation of old painted surfaces of wood and wood based material of any description over 10 cm in width or girth and applying one coat of synthetic enamel paint of approved tint all as specified & as directed. |
| 8 | M&L forwashing rubbing downincluding cleaning of mortar drops, smoke soot, moulds, moss, efflorescent salts, trading oil, greasy spots etc and preparation of plastered surfaces and applyingone coats of cement base paint of approved shade/tint on walls all as specified and as directed. |
| 9 | M&L for preparation, removing/scrapping down existing surface of old painted brick, stone, concrete, asbestos plastered or un-plastered surfaces of walls and applying one coat (finished coat) of plastic emulsion paint of approved shade/tint incl applying one coatofprimer complete all as specified and directed. |
| 10 | M&L for preparing old painted surfaces of wall etc. n. exc 0.1 sqm each including cutting in edges and applying one coat of synthetic enamel paint of approved tint, complete all as specified and directed. |
| 11 | M&L for writing letters or figures (Block, Roman, Italic or Indian) n. exc 30 cm high using Ist quality, synthetic enamel paint of approved tint complete all as specified and directed. |
| 12 | M&L for writing stops, commas, short lines, dashes, hyphens brackets etc. using Ist quality, synthetic enamel paint of approved tint complete all as specified and directed. |
| 13 | M&L for taking down cement plaster on PCC/brick surfaces including raking out joints hacking for key scrubbing down with water etc., complete all as specified & directed. |
| 14 | M&L for rendering 15mm thick in cement mortar 1:4 on fair faces of brick masonry or concrete surfaces of walls, finished even and smooth without using extra cement complete all as specified |
| 15 | M&L for preparation of newly plastered surfaces of wall & applying two coats of cement base paint of approved shade/tint over one coat of appropriate primer complete all as specified & directed. |
| 16 | M&L for rendering 15mm thick in cement mortar 1:6 on fair faces of brick masonry or concrete surfaces of walls, finished even and smooth without using extra cement complete all as specified |
| 17 | M&L for preparation of new plastered surfaces of walls and applying two coats of oil emulsion distemper (OBD) of approved shade/tint over a coat of primer chalk whiting over complete all as specified & as directed. |
| 18 | M&L for rendering 5mm thick in cement mortar 1:3 on concrete surfaces in ceiling, finished even & smooth without using extra cement complete all as specified. |
| 19 | M&L for preparation of newly plastered surfaces of ceilings & applying three coats of white wash complete all as specified. |
| 20 | Raking out joints/pointing to concrete block walling, stone masonry, any description, laid flat, work built in cement or cement lime mortar,complete all as specified & as directed . |
| 21 | Keyed pointing to concrete block walling, stone masonry, any description, laid flat, work built in cement or cement mortar, 1:4complete all as specified & as directed . |
| 22 | M&L for preparation of old painted surfaces of wood and wood based material of any description over 10 cm in width or girth and applying one coat of synthetic varnish (Finish coat) including removing existing nails, if any and filling the disturbed /uneven surface, holes/voids with wall care putty/POP to achieve the smooth surface all as specified & as directed. |
| 23 | Preparing old painted/plastered or unplastered surface of wall, complete removal of existing treatment by steel wire brushing/metal sheet including washing rubbing down and stopping of distempered and painted surface and applying two coats of exterior emulsion paint in different tint/shade,(camouflage pattern), as approvedby Accepting Officer, over one coat of alkali resistant primer as per manufacture\"s instructions and filling the disturbed /uneven surface, holes/voids with wall care putty/POP where ever necessary to achive the smooth surface all as specified and directed.Note:- Quoted rate shall be deemed to be included for work in buildings/structure esp water tanks of any height including necessary scaffolding |
| 24 | Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for (roof padding, flooring above ground floors) including roof treatment and removing from site all as specified and directed. |
| 25 | M&L PCC 1:3:6 type C-0 (using 12.5 mm graded stone aggregate) as in roof padding (average thikness 50mm thick) complete as directed by Engineer-in-Charge |
| 26 | M&L for 10 mm thick rendering in CM 1:3 over concrete surfaces (Roof) mixed with water proofing compound @ 3% by weight of cement complete all as specified.NOTE :Water proofing compound shall be measured and paid for separately as “Supply only” |
| 27 | M & L prepration of surface and providing Waterproofing membrane moisture cured, Polyurethane elastomeric liquid membrane waterproofing coating cold applied with brush/roller, with an elongation of >500% and tensile strength of 2 MPa as per ASTM D 412, 90 % Solid Content, shore A Hardness of min 50 as per ASTM D 2240, The system includes final base preparation as per note given below, PU primer application at 8Sqm/L and applying PU chemical in two coats at 1.8 kg per Sqm providing 1.5 mm DFT, complete as per Manufacturer specifications, Waterproofing membrane to be terminated on parapet wall in a V groove of size 25 mm x 25 mm atleast 300 mm above FFL which should be sealed with Polymer Mortar complete all as specified and directed for work in building/structure of any height, Completed as per manufacturer instruction.Note: Surface Preparation:(i) The surface to be treated should be sound and free from all types of dirt, dust and debris. Clean surface by brushing, scraping or chipping to eliminate all defective materials and foreign matter. Proper surface preparation needs dry mechanical grinding to expose base Substrate. Making of angle fillets(75mmx75mm all around the periphery of the wall with polymer modified mortar using SBR Latex ii) All construction joints and cracks > 1mm shall be treated by cutting V groove and filling with polymer modified SBR Latex and reinforced with geotextile membrane dipped in PU liquid Membrane before the 1st coat application. (Non Accessible roofs) |
| 28 | Supply only integral water proofing compound ISI marked. |
| 29 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing from site and rubbish off the premises. |
| 30 | M&L for glazed ceramic tiles, coloured, 450x350x7mm thick on vertical surfaces such as skirtings, dados and risers to steps etc, set & jointed in neat cement slurry & pointed in white or coloured cement to match over and including 10mm thick rendering in CM 1:4 on stone masonry surfaces. |
| 31 | M&L for joint free non skid ceramic tiles, coloured, 7 to 8 mm thick in floors etc. (square/rectangular) area of each tile exc. 0.06 Sqm but n. exc. 0.11 Sqm, set & jointed in neat cement slurry & pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 |
| 32 | M&L for light & dark coloured vitrfifed tiles 9-10 mm thick area of each tiles not less than 0.36 Sqm in floors etc set & jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed or bedding layer in CM 1;6 |
| 33 | All as per item no. 32 above but on vertical surfaces such as dados skirting and risers to step set & jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10 mm thick renedering in CM 1:4 on stone masonary surfaces |
| 34 | M&L for machine cut kota stone slab flooring 20 -25 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigmenst to match the shade of the slab including rubbing and polishing complete including 15 mm screed bed or bedding layer in cement mortar 1:6 as directed by Engineer-in-Charge |
| 35 | M&L for kota-stone slab 15 mm thick in riser of steps skirting dado skirting and risers to step set & jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10 mm thick renedering in CM 1:4 on stone masonary surfaces as directed by Engineer-in-Charge |
| 36 | M&L for granite (of any type ) tiles 20 mm thick machine cut in skirting /dado over and including 10 mm thick rendering in CM 1:4 on brick/stone/concrete masonry surfaces jointed with grey cement slurry and pointed with white cemewnt with admixture of pigment to match the shade of granite stone including grinding and polishing complete |
| 37 | M&L Granite (of any type) work 18-20 mm thick (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over 15 mm thick Screed bed or bedding layer for laying floor finishes in CM 1:4 complete all as specified and directed. |
| 38 | M&L for Cement patch work on wall/floor etc area n. exc. 1 sqmand depth n exc 15cm each all as directed by Engineer-in-Charge. |
| 39 | Demolition of cement concrete (unreinforced) in ground floors and pavings n. exc. 15 cm thickness (below or above ground level) and removing from site all as specified and directed. |
| 40 | M&L for 25 mm thick PCC 1:2:4 type B-0 using 12.5 mm graded stone aggregate in sub floors as directed by Engineer-in-Charge. |
| 41 | M & L 40 mm thick plain cement concrete type B1 1:2:4 ( with 20mm graded aggregate) as in floors finishing cement concrete surface even and smooth with out using extra cement. |
| 42 | M & L 40 mm thick plain cement concrete type B1 1:2:4 ( with 20mm graded aggregate) as in sub base of floor all as specified and directed. |
| 43 | M&L 75 mm thick PCC (1:3:6) type C2 (using 40mm graded stone aggregate) as in plinth protection finished surface even and fair without using extra cement all as specified and as directed by Engineer-in-Charge. |
| 44 | M&L 75 mm thick PCC 1:4:8 type D2 using 40mm graded stone aggregate in sub base of floor all as specified and directed. |
| 45 | M&L 100 mm thick PCC 1:4:8 type D2 using 40mm graded stone aggregate in sub base of floor all as specified and directed. |
| 46 | M&L chequered cement concrete tiles 25cm x 25cm x 25mm thick with grey cement and pigment, machine pressed, set, jointed and pointed in neat cement slurry in floors including 15 mm thick screed bedding layer in C:M 1:6 complete all as specified and directed |
| 47 | M&L 50 mm thick sand filling under floor or in foundation including watering and condolodation complete all as specified and directed. |
| 48 | M&L for providing and laying 60 mm thick factory made chamefered edge cement concret paver block of M-35 grade with approved colour design & pattern as in footpath parkslawns drive ways or lighttraffic parking etc of required strength thickness & size shape made by table vibratory method using PU mould laid in required colour & pattern over and including 50 mm thick compacted bed of fine sand comapcting and proper embedding / laying of interlocking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator filling the joints with sand and cutting of paver blocks as per required size and pattern finishing and sweeping extra sand as directed by Engineer-in-Charge |
| 49 | M&L for hacking out old broken glass (any thickness, size, quality or description) from metal frame glazed with putty including punching or drilling out old glazing pin/spring, clips and providing new ones. |
| 50 | S&F sheet glass 3 mm thick, ordinary quality and glazing with oil putty or wooden beads supplied with shutters in square n.exc. 0.5 Sqm in each pane at any height (G, G+1, G+2) as directed by Engineer-in-Charge |
| 51 | S&F Figured glass 3 mm thick, pin head type and glazing with oil putty or wooden beads supplied with shutters in square n.exc. 0.5 Sqm in each pane at any height ( G, G+1, G+2) as directed by Engineer-in-Charge. |
| 52 | S&F floor door stopper, with 150 mm long cover plate, of aluminium alloy body and tongue, anodized, with hard drawn steel spring, fixed in floor. |
| 53 | Resecuring or easying and adjusting without taking down shutters of any description (door/window) exe 2.0sqmeach |
| 54 | Resecuring or easing & adjusting without taking down shutters of any description exc 1 Sqm and n exc 2 Sqm each. |
| 55 | S&F teak wood lipping 6mm thick fixed with nails to 18/19mm thickblock board/doors or veneered particle board. |
| 56 | S & F in repair stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of apreture 1.4 mm & fixed with stainless steel wire staples fixed. |
| 57 | Welding in repairs exc 2.5 cm & n exc 5 cm in length & thickness of metal n.exc 6 mm all as specified and directed by Engr-in-charge |
| 58 | Taking down shutters not exceeding 1.0 sqm each ,remove from site to store or as directed by Engineer-in-Charge |
| 59 | S&F in repair for 18/19 mm thick , prelaminated particle board ISI marked interior grade pelaminated both sides with decorative choice laminations , fixed with screws to timber frame work for doors , partition on wall in cup board/ kitchen cabinets etc in shelves partition and shelves of built in cup board almirah book case toilet boxes racks pelmets etc and similar works |
| 60 | S&F Continous (piano) hinges mild steel bright finish or electro galavanized width of flaps (when open ) 30 mm |
| 61 | S&F 9 mm thick plywood in repaire, grade BWR, type BB, fixed with screws to any type of frame work/surface with wooden fillets/frame whereever necessary in any possition complete all as specified and directed. |
| 62 | S&F 40 mm dia cupboard knobs of fixed with nut screw and washers of mild steel bright finished |
| 63 | S&F ball catches with 8 mm dia steel ball and brass body and striking plate including letting in and fixed |
| 64 | S&F100 mm Hasp and staple, safety type, baluminium anodisedmild steel hinge pin including bolt to hinge plate and fixed with screws |
| 65 | M&L for second class hardwood plain fillets of sectional area n exc 3 sq cm square ,rectangular or triangular in section clean sawn bull nosed splayed chamfered or rounded on one edge or face secured with nails or brads |
| 66 | S&F in repairs sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long |
| 67 | S&F 5.5 mm thick, 600 X 450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with CP brass screws and cup washers. |
| 68 | S&F in repairs Corner glass shelf assembly consisting of 5.5 mm thick sheet glass shelf exc 15 cm wide with chromium plated bracket guard and railing |
| 69 | S&F in repairs stainless steel plate rack 0.56mm thick of standard pattern of size 788x915x254 mm (if same size not avail count just next size)complete |
| 70 | Taking down Shutters of any description exc 1 sqm and n exc 2 sqm each and removing from site. |
| 71 | Taking down Shutters of any description exc 2 sqm each and removing from site. |
| 72 | Taking down chowkats or frames exe 1.5 Sqm but n.exc 4 sqm each with shutter (without taking off shutters from the frame) and removing from site complete all as directed. |
| 73 | Taking down chowkhat or frame n exc 1.50 sqm each (with out taking of shutters from the frame) and removing from site complete all as directed. |
| 74 | S&F 30 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sidescomplete all as specified and as directed all as specified and as directed |
| 75 | Dismantling wrought iron or mild steel work of any description in any possiton not otherwise provided for |
| 76 | Framed work as in doors or gates, cooler stand of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings(exclusive or steel sheeting or other covering, running rails and guides) and hanging,also fastening and fixingof Fe-290(Gde E-165) complete |
| 77 | S&F in repairs steel windows with side hungs shutters including projecting type hinges with steel handles, steel peg stay complete with glazing bar, devetailed or welded.Note:Quated rate included any size or shape of window as per drawing provided by Engr-in-charge at the time of execution. |
| 78 | S&F in repairs steel windows with side hung shutters including projecting type hinges with steel handle and steel peg stay complete without glazing bars as directed by Engineer-in-Charge . |
| 79 | S&F, in repair Box type steel ventilator with top hung shutters (double shutters for glass and guaze) jointed together with an including grills using 10mm square barsincluding box type hinges with steel handle and steel peg stay complete with glazing bars devetailed and welded complete all as specified and as directed. Note : Glass/guage shall be measured and paid separately under respective item. |
| 80 | S&F frame work such asguard bars ,grills, grating etc with ends of bars shouldered and or rivetted or forged into spikes, framed guard bars, barred iron doors,ladders etc and similar wks conforming to Fe-290 grade E-165. |
| 81 | S & F Plain framed, panelled shutter of 2nd class hard wood(two panel) of 35mm thickfactory made shutterwith lock rail and panel of 9 mm B.W.P commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS: 1003 (Part I), kiln seasoned and chemically pressure treated |
| 82 | M/L for factory made, Glazed and skeleton shutters for door/window,of thickness 35mm of IInd class hard wood , open rebated and prepared to receive glass, gauze, etc. (without sash bars), edge of framing plain, chamfered or rounded, fitted with cut and mitred beds for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8. clause 8.20 (a); supplied and fitted to chowkats Note: Glazed or cloth etc in panelsor sash square shall be measured seperately |
| 83 | S&F GalvanisedMS wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised wire staples. |
| 84 | S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, supplying & fixing in opening as per directed. |
| 85 | S&F Factory made solid panel PVCdoor shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC `C\" channel heaving a PVC sheet strip of 20mm width suck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing. |
| 86 | M&L for preparation of new steel surface of any description over 10cm width or girth and applying two coats of synthetic enamel paintover one coat of red oxide complete all as specified and directed. |
| 87 | M&L for preparation of new wooden surface of any description over 10cm width or girth and applying two coats of synthetic enamel paintover one coat of pink primer complete all as specified and directed. |
| 88 | S&F Butt hinges,extruted aluminium alloy with galvanised mild steel type C21of size 100 mm. |
| 89 | S&F Aluminium anodised barrel tower bolt of extruded section 150mm size |
| 90 | S&F 300 mm long aluminium alloy anodized silding door bolt with hasp staple (bolt type ) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts and sliding bolts of extruded sections or casr aluminium alloy. |
| 91 | S&F Extructed aluminium alloy handles, fabricated type,anodised of size 150mm. |
| 92 | S&F mild steel 300 mm helical door spring hinges with steel wire spring, stove enamelled black complete all as specified and as directed |
| 93 | S& F butt hinges ,40 mm of size cast brass with mild steel hinge pin, bright polished type B-11 |
| 94 | S&F in repair butt hinges 100 mm long medium weight, cold rolled mild steel complete all as specified and directed. |
| 95 | S&F in repairs 300 mm long aluminium alloy anodized silding door bolt with hasp staple (bolt type ) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts and sliding bolts of extruded sections or cast aluminium alloy. |
| 96 | S&F in repairs peg stay 250mm/300mm long stopping of steel windows/ventilators including welding(if required) & fixing complete all as directed by Engr-in-charge. |
| 97 | S&F in repairs left/right MS handle of steel windows including welding(if required) & fixing complete all as directed by Engr-in-charge. |
| 98 | S&F in repairs projecting type hinges of steel window/ventilator, 75 mm long including necessary fixing & welding work etc complete all as directed by Engr-in-charge. |
| 99 | S&F in repairs 150 mm long aluminium, anodized, barrel tower bolts of extruded section and fixed. |
| 100 | S&F in repair mild steel 300 mm helical door spring hinges with steel wire spring, stove enamelled black complete all as specified and as directed |
| 101 | S&F in repairscolouredAlluminium stripbeading of 18-20 mm wide and 2 to 3 mm thick with rubber sheet 20mm widefixing at bottom to existing doors all as directed by Engineer-in-Charge. |
| 102 | S&F in repair Door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed aluminium extruded section |
| 103 | S&F in repairs aluminium handles, cast type, anodized, of size 150mm. |
| 104 | S&F PVC lid of PVC water tank suitable for 500/1000 ltrs capacity fixing to existing water tank with necesarry fixing arrangments at any possition. |
| 105 | S&F in repairs 15 mm bore bib taps, cast copper alloy, chromium plated, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule. |
| 106 | S&F in repairs 15mm bore pillar tap, fancy type cast copper alloy with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly nuts, screwed for iron pipe and fixed complete. |
| 107 | S&F in repairs, 15 mm bore stop valve, fancy type, chromium plated with long shank and cupscrewed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipe or for unions. |
| 108 | S&F in repairs, 15 mm bore stop valve, fancy type, chromium plated with long shank and cup (concealed type), screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipe or for unions. |
| 109 | S&F in repairs 20 mm dia gun metal globe or gate valve with iron wheel head screwed both ends for iron pipes |
| 110 | S&F in repair brass chromium plated shower rose of 125 mm size with swivel joint including fixing to steel pipe or union. |
| 111 | S&F in Repairs shower arm 15 mm size, 195mm long with bend of 45degree with flange of PTMT any colour.(Minimum weight 40gms) ccomplete all as specified and directed. |
| 112 | S&F in repairs Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specifiede complete. |
| 113 | S&F in repairs 15 mm bore brass CP wall mixer for mixing hot & cold water screwed down for iron pipe for wall |
| 114 | S&F in repairs 15 mm bore brass CP washbasinmixer for mixing hot & cold water incl all fixing with connection pipes etc |
| 115 | S&F in repairs 15 mm bore brass CP wall mixer for mixing hot & cold water wih 3 -Function hand shower, SS grade 1.5 meter tube and crutch, incl all fixing with connection with iron pipe for wall etc |
| 116 | S&F in repairs 15 mm bore CP 3 -Function hand shower, SS grade 1.5 meter tube and crutch, incl all fixing with connection with wall mixture iron etc |
| 117 | S&F in repairs PVC pressure jet for EWC heavy duty. |
| 118 | S&F in repairs brass aluminium anodised towel rail, 20mm dia, D type, 60cm long between flangesall as specified and directed. |
| 119 | S&F in repairs PVC connection 15 mm size with PTMT nuts of length 450 mm. |
| 120 | S&F in repairs PVC waste pipe low density poly ethelene of 32/40 mm bore of suitable length for WHB/urinal/sink, complete all as specified. |
| 121 | S&Fin repair grating doom 125 mm dia with / without waste hole of PTMT (min wt 40 gms). |
| 122 | S&F in repairs stainless steel toilet paper holder fixed to walls with chromium plasted (CP) brass screws. |
| 123 | S&F in repairs vitreous china wash basin, white, flat back, size 550x400mm including brackets, cutting for and pinning in ends of brackets or erecting stand, brass chromium plated perforated waste coupling/ fittings 32 mm dia with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed and PVC waste pipe of 32mm bore and of suitable length, 15mm bore pillar tap, cast copper alloy with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly nuts, screwed for iron pipe PVC connection 15 mm size with PTMT nuts of length 450 mm.complete all as specified. |
| 124 | S&F in repairs, EWC vitreous china wash down water closet pan (pedestal pattern), white, with and including plastic water closet seat, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device fixed complete all as specified. |
| 125 | S&F in repairs vitreous china squatting pan, ‘Orissa’ pattern, size 580 mm x 440 mm, white with integral foot rests, including PVC \"P\" trap, embedded and set in PCC 1:5:10 type E-2 and making good to floor including removing rubbish. |
| 126 | S&F in repairs PVC valveless, syphonic action type, flushing cistern, low level, 10 litres capacity, white, with inlet, ball valve, float and handle including brackets. |
| 127 | S&F in repairs internal flushing cistern kit, washer, flushing handles etc. |
| 128 | S&F in repairs plastic water closet seat covered closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device |
| 129 | S&F in repairs single mirror bath room cabinet moulded body and framed (made from strong and fine quality ABS plastic ) with hinged door of size 16 \" x 12 \" x 6 \" white or ivory colour fixed on wall with appropriate rawl plugs . Make : Prayag/Polytuff or equivalant |
| 130 | S&F in repair 1000 litres capacity rotational moulded polyethylene water storage tanks ISI Marked (cylindrical vertical with closed top), hoisted and fixed in position all as specified in SSR Part-I, connecting up pipes including 20 mm bore ball brass valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic plastic ball screwed for iron pipe and fixed. (Minimum weight of ball valve - 210 gms) |
| 131 | S&F in repair 500 litres capacity rotational moulded polyethylene water storage tanks ISI Marked (cylindrical vertical with closed top), hoisted and fixed in position all as specified in SSR Part-I, connecting up pipes including 20 mm bore ball brass valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic plastic ball screwed for iron pipe and fixed. (Minimum weight of ball valve - 210 gms) |
| 132 | S&F in repairs 15/20 mm bore ball valve high pressure of PTMT with epoxy coated aluminium rod &high density plastic ball screwed for iron pipe and fixed. (Minimum weight 210 gms) |
| 133 | S&F in repairs Stainless Steel Curtainin any length, high strength SS pipe having outer dia 20 mm all as directed by Engineer-in-Charge. |
| 134 | S&F in repairs decorative finals Stainless steel same colour of brackets or as directed by Engineer-in-Charge. |
| 135 | S&F in repairdrapery rod in any length, high strengh MS pipe with corrugated PVC extrusion having outer dia 28 mm with plastic ring of ABS plastic of dia 56 to 58 mm all as directed by Engineer-in-charge |
| 136 | S&F in repair decorative finals ABS plasticfancy typebracket,fancytype hook in matching colour of steel powder quoted paint of same colour of rodincl all as directedEngineer-in-charge. |
| 137 | M&L for providing and injecting chemical emulsion for post construction anti termite treatment along external wall where the apron is not provided using chemical emulsion at therat of 7.5 ltr per Sqm of the vertical surface of the sub structure to a depth of 300 mm including excavating channel along the wal and rodding etc complete all as specified and directed. |
| 138 | S&Fin repair stack clamps out of 50mm by 5 mm flat iron & 16mm dia mild steel iron stay incl bolt & nuts & securing ends of stays to walls for 100mm pipe. |
| 139 | M&L Cleaning and removing all scale dirt etc. from water storage tanks and from mouth of circulating pipes etc. and writing the date of cleaning and next due date for cleaning of tank, capacity of tanks exc. 500 liters and not exc. 1000 liters complete all as specified and as directed. |
| 140 | M&L Cleaning and removing Air blockage from water supply pipe line tank to kitchen, bath,Toilet or any are in accn with open joints,or using pressuremotor complete all as specified and as directed. |
| 141 | S&F in repairs stainless steel soap dish made of stainless steel 1.00mm thick, approximate 150x150 mm fixed to plugs with chromium plated brass screws. |
| 142 | M&L for filling of joints of tiles/WC & WHB corner with white cement area n. exc. 1 Sqm each all as directed by Engineer-in-Charge. |
| 143 | S&Fkitchen cabinet in required sizes at site made out of 18 mm thick WPC Board (plain colour)of standard grade density 650 KG/CBM consisting of carcase 18 mm thick WPC sheet & provision of shutters made out of 18 mm thick WPC sheet all required brackets 5.5 screws etc. The panels shall be fabricated using adhesive and screws where ever required. All the edges shall be covered with 2mm edge bonding tape or 90 deg edge bent finish as per make and specification mentioned as per drawing and specification approved by engineer-in-charge. |
| 144 | Taking up or down steel tubing 15 mm bore and connections including cleaning for refixing or removing from site. |
| 145 | Taking up or down steel tubing 20 mm bore and connections including cleaning for refixing or removing from site complete all as specified and directed. |
| 146 | Supply and laying 15 mm bore tubes, galvanized steel,medium grade, with all fittings and fixed complete to walls and ceilings or laid in floors all as specified and directed. |
| 147 | Supply and laying 20 mm bore tubes, galvanized steel,medium grade, with all fittings and fixed complete to walls and ceilings or laid in floors all as specified and directed. |
| 148 | Refixing old steel tubing, 15 mm bore, and connections with new or old position (Walls, ceiling, floors, etc.) Note :- Steel tubes obtained from item No. 3 above shall be used under this itemall as specified and directed. |
| 149 | Refixing old steel tubing, 20 mm bore, and connections with new or old position (Walls, ceiling, floors, etc.) Note :- Steel tubes obtained from item No. 4above shall be used under this itemall as specified and directed. |
| 150 | Cutting chases stone concrete blocks pinning in making good to facing where required and pointing in CM 1:3 to ends or edge of landing steps cills sunshades shelves lintels eytc and cutting chases for conealed water tuibing making goodnot exceeding 10 cmgirth for stone wallsall as specified and directed. |
| 151 | S&F in repairs vitreous china wash basin, white, flat back, size 550x400mm including brackets, cutting for and pinning in ends of brackets or erecting stand, brass chromium plated perforated waste coupling/ fittings 32 mm dia with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed and PVC waste pipe of 32mm bore and of suitable length, complete all as specified. |
| 152 | S&F in repairs grating doom 125 mm dia with or without waste hole of PTMT (minimum weight 40 gms) and fixing with gray or white cementall as specified and directed. |
| 153 | S&F in repairs, 15 mm bore bib tap, standard of PTMT, any colour screwed for iron pipe and fixed (minimum weight 15mm – 90 gms)all as specified and directed. |
| 154 | Taking down eaves gutters and rain water pipes (any size or pattern) including all fittings, heads, shoes, bends, swan necks, etc, including cleaning or refixing or removal from site all as specified and directed. (measured overall as fixed along the centre line over fittings and accessories)all as specified and directed. |
| 155 | S&F 75 mm bore PVC (SWR) pipes type ‘B’, single socketed, in any length with rubber ring joints fixed to wallsall as specified and directed. |
| 156 | S&F 110 mm bore PVC (SWR) pipes type ‘B’, single socketed, in any length with rubber ring joints fixed to wallall as specified and directed. |
| 157 | S&F in repairs PVC (SWR) door bends 110 mm dia with acess doorall as specified and directed. |
| 158 | -do- but 75 mm dia..with acess doorall as specified and directed. |
| 159 | S&F in repairs waste coupling of PTMT for wash basin(half or full threaded) 32 mm bore of discharge pipe,(Minimum weight– 45 gms.)all as specified and directed. |
| 160 | S&F in repairs shelf of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats (Minium weight 300 gms)all as specified and directed. |
| 161 | M&L for repairs to leakage in existing 15 mm bore pipe line by providing elbow/union/socket/tank nipple/nipple up to 200 mm all as directed by Engineer-in-Charge. |
| 162 | M&L for repairs to leakage in existing 20 mm bore pipe line by providing elbow/union/socket/tank nipple/nipple up to 200 mmall as specified and directed. |
| 163 | M&L for repairs to leakage in existing 25 mm bore pipe line by providing elbow/union/socket/tank nipple/nipple up to 200 mm all as directed by Engineer-in-Charge. |
| 164 | M&L for repairs to leakage in floors of WC/Bath Room/Kitchen by breaking of existing floor and providing new PVC (SWR) floor trap, suitable for type ‘B’ pipes, 75 mm dia of outlet, plain with grating including jointing with solvent cement and making good floor to match with existing floor all as directed by Engineer-in-Charge. |
| 165 | Fixing/tightening/hanging of kitchen rack, pilmet box, curtain rod with fancytype hook/brackets/holders in matching colour, cloth hanging wires, dressing tables/mirrors, towel rails/ring, and like on wall withscrew/nails including all necessary fixing arrangements, complete all as specified and directed.Note: Quated rate for each article |
| 166 | S & F in repairs stack clamps out of 50 mm x 5 mm flat iron and 16mm dia round iron stays including bolts and nuts & securing ends of stays to wall or roof for 110 mm bore of pipe complete all asspecified and directed. |
| 167 | M&L in repairsto sink made of stainless steel by providing waste coupling brass, chromium plated of 32 mm with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed 32 mm complete all as specified. |
| 168 | M&L in repairsto sink made of stainless steel by providing waste coupling brass, chromium plated of 40 mm with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed 40 mm complete all as specified. |
| 169 | S&F in repair sink with drainage board made of stainless steel 1.00mm thick kitchen or laboratory with plugs, washers and wastes, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915 mm x 460 mm, bowl size 410mm x 330 mm x 160 mm and PVC waste pipe of 32mm bore and of suitable length, complete all as specified. |
| 170 | S&Fin repairs sink made of stainless steel 1.00 mm thick kitchen or laboratory with plugs, washers and wastes, including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm, bowl size 410mm x 330mm x 160mm and PVC waste pipe of 40 mm bore and of suitable length, complete all as specified. |
| 171 | S & F powder coated aluminium sliding window shutters with frames (consisting of two nos glazed shutters and one no gauze shutter) series-D (25mm) 3 track sliding shutters, duly fitted with neoprene beading glazing clip, locking device, heat absorbing glass 5 mm nominal thickness in glazed shutters, stainless steel wiremesh of 0.254mm nominal dia of wire and 0.95mm average width of aperature in gauzed shutter complete all as specified and as directed. |
| 172 | S&F powder coated anodized aluminum frame for doors, windows ventilations with one or more rebates including joining cleat for fixing etc. complete all as specified. |
| 173 | S & F powder coated Anodised aluminium window and ventilator shutters side hung type without sash bar, aluminium sections weighing 0.55 kg/m including necessary joining, cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as hinges type B-21 100 mm long (2 nos) suitable handle 1 No complete all as specified |
| 174 | S&F fabricatedpowder coated anodized aluminium grill of size 75x75 mm, using 6mm dia bars fixed to outer portion of chowkhat using U/V section runners complete all as specified and as directed |
| 175 | S&F 4 mm thick one side frosted sheet glass ordinary quality and glazing in square n.exc 0.5sqm in each pane fixed with neopunerubber gasket in aluminium frame complete all as specifed |
| 176 | Dismantling wall and ceiling boards (fibre,pulp,insulation etc) or insulation boards/slabs etc any thickness including cover fillets completeall as specified and directed. |
| 177 | S & FAnodised aluminium snap grid frame work Size of grid 605 x 605mm for false ceiling all as specified Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified |
| 178 | M & L 4 MM thickness Nonasbestos fibre cement building boards fixed or laid/ inserted to timber/GI/Alumi nium framework with screws all as spd and directed. |
| 179 | M & L 4 MM thickness PVC designer ceiling boards fixed or laid/ inserted to timber/GI/Alumi nium framework with screws all as spd and directed. |
| 180 | Providing and fixing Gypsum Board 12mm thick in ceiling fixed with screw as per manufacturers instructions complete all as specified and as directed |
| 181 | M & L forProviding and fixing 10mm thick plaster of paris ceiling (Gypsum anhydrous) to flat/curved surface over 2nd class soft wood fillets, or metal frame work and reinforced with G.I. wire mesh (Fillets, metal frame work and G.I. wire mesh paid separately) with POP mulding as per required complete all as specified and as directed |
| 182 | S & F stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of apreture 1.4 mm & fixed with stainless steel wire staples fixed for POP and similar work at ceiling. |
| 183 | M&L for preparation of old painted surfaces of tile / cement base material of any description over 10 cm in width or girth and applying one coat of terracotta paint of approved tint all as specified & as directed. |
