|
| 1 | Transporting defective Openwell submersible Pump of Capacity 1 to 5 HP capacity to work shop, dismantling the motor,taking out burnt winding wire from the stator, cleaning of the casing and the stator with wire brush,rewinding of motorwithsuperior quality copper winding wire of existing size including varnishing an drying, cable jointing, reassembling installing the motor and pump , reconnecting all pipe and electric connections and testing on full load complete as directed by Engr-in-Charge. |
| 2 | Replacement of following defective parts of submersible pump of 1 to 5 capacity : - (a) CI stage casing |
| 3 | (b) Bearing bush rubber |
| 4 | (c) Stainless Steel sleeve at staging |
| 5 | (d) Brass impellers |
| 6 | (e) Neck ring brass |
| 7 | (f) Key for impellers |
| 8 | (g) NRV body of pump |
| 9 | (h) MS stud with nuts of size of 3/8\" X 2\" for stage casing |
| 10 | (j) Bush gun metal at intermediate section |
| 11 | (k) Steel sleeve at intermediate section |
| 12 | (l) CI intermediate section |
| 13 | Remetalling turning & polishing of motor shaft of submersible motor of capacity 5 HP to 20 HP |
| 14 | S & F pressure pump motor of 1 HP power capacity with inlet and outlet of 25 mm diawith pressure switch 230 volt 50 Hz electrical input as approved by Engineer-in-Charge all as specified and directed. |
| 15 | M&L for earthig complete with galvanised steel earth plate electrode 60 x 60cm x 6.3mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below ground level) with top edge of the plate not less than 1.5 mtr below normal ground level connected to galvanised earth strip 32 x 6 mm by means bolts, nuts, check nuts, and washers of galvanised wire as shown in electrical plate No 5 connected to earthing test point, all as specified or indicated including testing on completion including earth work and excavation in any type of soil/rock,PCC 1:3:6 type C1 earthing chamber, precast RCC slab 50mm thick in cement concrete 1:2:4 type B1, reinforced with welded steel wire fabric weight not less than 4 Kg/Sqmtr, funnel with GI watering pipe of 20mm bore, medium grade wire mesh and legs,test point etc all as specified and directed. |
| 16 | Taking down the existingunserviceableStarter Deltastarter& replace with new Star delta starterall as per suitable for 5 HP motor , relay range 9 - 14 amps complete all as specified and directed. |
| 17 | Taking down the existingunserviceableDOLstarter& replace with new Star delta starterall assuitable for 1 HP motor , relay range 3 - 5 amps complete all as specified and directed.. |
| 18 | S&F PVC sheathed submersible cable 3 coremulti stranded copper conductor of size 6 sqmm complete all as specified and as directed. |
| 19 | S&F PVC sheathed submersible cable 3 coremulti stranded copper conductor of size 4 sqmm complete all as specified and as directed. |
| 20 | Supply and fixing single phase preventer cum phase sequence correctorcomplete all as per specified and as directed. . |
| 21 | Taking down burnt Agitator motor form site and transporting the same to nearest authorized work shop, dismantling the pump motor assembly and rewinding the burnt motor with same gauge of PVC insulated supper enameled copper wire as per manufacture\"s instruction including servicing/overhauling the pump, re-assembling and brought back to site complete all as specified and as directed by Engr in charge. |
| 22 | Taking out old unserviceable GI Pipe of any size from site complete all as specified and as directed. Note :The Excavation and earth work shall be measured and paid separately under relevant item of Schedule. |
| 23 | Supply and lay pipe galvanized, Medium grade including fittings 20 mm fixed complete to walls and ceiling or laid in floor directed. |
| 24 | Supply and lay pipe galvanized, Medium grade including fittings 25 mmfixed complete to walls and ceiling or laid in floor directed |
| 25 | Supply and fix Gun metal ,globe Gate Valves with iron wheel head of 20 mm dia bore complete with all accessories all as specified and directed. |
| 26 | Supply and fix Gun metal ,globe Gate Valves with iron wheel head of 25 mm dia bore complete with all accessories all as specified and directed. |
| 27 | Excavation in trenches in soft/loose soil not exc. 1.5 metre wide and not exc. 1.5 metre in depth and getting out for taking up / layingunder ground electric cable complete with all accessories all as specified and directed by Engineer-in-charge. |
| 28 | Returning, filling in, including spreading leveling watering and well ramming in layers not exceeding 25 cms in depth complete with all accessories all as specified and directed by Engineer-in-charge. |
| 29 | Removing excavated materials n.exc 50m and depositing were directed at a level n.exc. 1.5m above the starting level all as specified and directed by Engineer-in-charge. |
| 30 | Supply & Fixing water proofLED type Fountain Multicolour light of 15 watt with SMPS controlled complete with all accessories internally prewired and necessary mounting arrangements ie clamps,nuts,bolts ,washers etc, including necessary connection ,complete all as directed by Engineer-in-charge. |
| 31 | Maintenance & servicing of existing make 100 KVA DG set including tappet cover adjustment & gasket replacement including replacement of following spares complete all as specified and directed by EIC.Note: Spares will be measured & paid separately under respective items here in after. |
| 32 | Supply only in replacement Diesel fitter. |
| 33 | Supply only in replacement Lub oil filter. |
| 34 | Supply only in replacement Radiator hose pipe set |
| 35 | Supply only in replacement Fan belt |
| 36 | Supply only in replacement Carbon bush |
| 37 | Supply only in replacement high pressure oil pipe |
| 38 | Supply only in replacement LLOP Sensor |
| 39 | Maintenance & servicing of existing make200 KVA DG setincluding tappet cover adjustment & gasket replacement including replacement of following spares complete all as specified and directed.Note: Spares will be measured & paid separately under respective items here in after. |
| 40 | Supply only in replacement Diesel fitter. |
| 41 | Supply only in replacement Lub oil filter. |
| 42 | Supply only in replacement Radiator house pipe |
| 43 | Supply only in replacement Fan belt |
| 44 | Supply only in replacement high pressure pipe |
| 45 | M & L for replacement of old engine oil from the DG Set sump of various DG Set cleaning the oil sump thoroughly supply & filling new engine oil of Make : Servo super 20W 40 of Indian Oil or Equivalentgrade of Hindustan Petroleum all as approved & directed by EIC. |
| 46 | M & L for topping up of water coolent in radiator of DG set TVS Girling/volvo line or of equivalent make all as approved & directed by EIC. |
| 47 | S & F DG control relay with all DG & main supply parametersfor 100 KVA & 200 KVA DG set aii as specified & directed. |
| 48 | M&L for dismantling of FIP for overhauling and calibration in authorized workshop including replacement of worn-out rings plungers,damper plate,gaskit etc and reassembling testing complete for following DG sets. (a) 100 KVA |
| 49 | All as per item No. 48 above but for 200 KVA |
| 50 | Repair overhauling of self starter including replacement of worn out clutch assembly bush, spring, plunger assembly ,solenoid switch, carbon brushes, spring etc for the following DG set. (a) 100KVA |
| 51 | All as per item No. 50 above but for 200 KVA |
| 52 | Repair/overhauling of dynamo/charging alternator including replacement carbon ,brushes holder ,spring commutator/slipring assembly bearing regulator its of any make, type and capacity, complete all as directed. (a) 100 KVA |
| 53 | All as per item No. 52 above but for 200 KVA |
| 54 | Cleaning of the fuel tank of DG sets of following capacity after decaning the diesel, after through cleaning with kerosene oil including replacement of level indicator pipe complete all as directed by EIC.(a) 100 KVA |
| 55 | All as per item No. 54 above but for 200 KVA |
| 56 | Dismantling and removing of water pump assessmbly complete from the engine repair/overhaulling the same by replacing worn components like bearing, impeller, bushes, oil seal, water seal, gaskit etc. reassembling,refixing and testing complete for the following.(a) 100KVA/200 KVA |
| 57 | M & L replacement of Automatic voltage regulator suitable for DG set of following rating approved Make & model by EIC :-(a)100 KVA |
| 58 | All as per item No. 57 above but for 200 KVA |
| 59 | M & L for replacement of fuel shutdown valve assembly complete testing including replacement of old unserviceable valves of any capacity DG set, complete all as directed by EIC . |
| 60 | M & L for replacement of bendix drive pinion assembly of self starter of capacity 100 KVA to 200 KVA DG set complete all as specified & directed . |
| 61 | M & L for replacement of existing make and model fly wheel ring including heating for press fitting for engine of following DG set complete all as specified & directed .(a) 100 KVA to 200 KVA |
| 62 | M & L for replacement of stop solonoid 100 KVA to 200 KVA DG Set complete all as specified & directed. |
| 63 | Dismantling of radiator of DG set of capacity 100 to 200 KVA and transporting to work shop for servicing/cleaning after dismantling twin tanks, replacement of gasket packing , nuts ,bolts , washers ,descaling with appropriate chemical and welding of copper brazing of damazed fins/tubes and reassembling & refixing in same position after testing complete all as specified & directed . |
| 64 | M & L for replacement of moulded rectifier unit on existing make DG set of capacity 140 ohm for alternator excitor unit complete all as specified & directed . |
| 65 | M & L for repairing of complete GENSET engine wiring including extension of existing PVC insulated , stranded copper conductor wire of size 2.5 sq mm /1.5 sq mm for control/ signal circuit complete with & including copper lugs, PVC ties , fasteners & synchronisation and calliberation ofengine control panel complete all as specified & directed . |
| 66 | M & L for replacement of SMPS based Electronic Battery Charger suitable for 12 / 24 Volts battery charging system complete all as specified & directed. |
| 67 | Supply & replacement of old unserviceable battery 12 Volts 180 AHmaintenance freesuitable for DG sets . Make- Excide/AMCO or equivalent. |
| 68 | M & L for replacement ofold unserviceable battery leadwithfactory made lead of PVC insulsted standred copper conductor of size 50 Sq with copper lugs duly welded on both sides of cablelength minimum 1 mtr all as directed. |
| 69 | Supply and lay PVC insulated unsheathed cable electric control cables with stranded copper conductor of size 6 sqmm 4 core 1100 volts grade complete all as specified and directed. |
| 70 | Comprehensive maintenance and servicing of Shutter gate of any size with providing oiling & greasing near rolling surface and replacement of unserviceablespare parts all as directed. |
| 71 | M&L for painting of Shutter gateout side & inside with synthetic enamel paint grey/ Blue colour scrubbing preparation for painting atdifferent Mes installation under AGE E/m office all as directed & specified. |
