|
| 1 | Earthing with G.I. earth pipe 4.5 meter long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. (but without charcoal/ coke and salt) as required. |
| 2 | Providing and fixing 25mm x 5mm GI strip on surface or in recess for connections etc as req. |
| 3 | Providing and Fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/submain wiring/ cable as required. |
| 4 | Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/HUME/ METAL pipe as req.Up to 35 sq.mm. |
| 5 | Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existingmasonry open ductas required.Up to 35 sq.mm. |
| 6 | Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc..direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc.complete as 63 mm dia (OD-63 mm & ID-51 mm nominal) |
| 7 | Supplying and fixing of light class G.I. pipe of 50 mm dia. (nominal) 3 metres length along the pole for protection of under ground cable as required. |
| 8 | Supplying and erection of galvanised ‘D’ iron clamps complete with shackle insulator (75 mm X 90 mm),G. I. bolts, nuts and washers, coach screws etc. as required. |
| 9 | Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit req (a) 3 x 1.5 sq. mm |
| 10 | Supply of XLPE insulated PVC sheathed Al. Conductor Armoured Cable 1.1KV grade conforming to IS-7098 of following size:-2C*6 sqmm |
| 11 | Supply and erection of 4.0mtr. height above the foundation level cast iron decorative light pole, fabricated with cast iron FG150 Grade Casting with MS Pipe inside, having seven sections of cast iron fabrication with MS pipe inside. The length and outer dia. of the different sections should be, bottom most base section should have dimension of (850 x 380 )mm, second section should be of (215 x 105)mm, third section should be of (915 x 105)mm, fourth section should be (100 x 105)mm, fifth section should be of (1638 x 105)mm, sixth section should be of (228 x 75)mm and the top most section should be of (119 x 79)mm. In which the all the portion should be made of cast iron. The 4.0mtr. pole should have full length hot dip galvanized MS Pipe complete from top to bottom inside the cast iron pole to strengthen the pole structure. Total Weight of the pole should be of 120Kg with the tolerance of +/-5%. The bottom CI portion should have round mounting base of not less than 380mm dia and thickness not less than 18mm and must be provided with service window comprising of 4way, 25Amp connector terminal and a MCB. The pole should be duly PU painted i/c accessories etc. as req |
| 12 | Supply and fixing of 50 watt IP65 decorative single piece LED fixtures with die cast aluminium housing frosted PMMA / PC diffuser, suitable for upward mounting with power LEDs white/warm white fitted with suitable extruded aluminiumheat sinks, high voltage protection and suitable constant current LED driver extra as required. Technical Particulars i) Size of fiiting- 580mm x 340mm, base section inner dia 64mm and outer dia- 71mmii) Total power of light fixture- 50 Wattiii) Input voltage-AC 120 to 270volt 50Hzv) Power factor 0.95v) Minimum lumen output of LEDs - 100 Lumen per wattvi) Luminaire protection - IP65 |
| 13 | Supply and fixing of following size double ornamental cast iron bracket with cast iron embellishments matching with the pole. The width of the bracket should be 1300mm and height of mid section of bracket should be 700mm. Bracket should be PU painted with & lacquer coating with gold/copper/silver colour with green/ black base as reqd. fixing on the existing pole for mounting LED street light fitting i/c, painting etc. as reqd. |
| 14 | Fabrication, supply and erection of 5 metre height MS decorative street light pole with attached name plate of suitable size including engraved name of area representative with desired colour. The pole is straight line with zigzag arm with fixed mild steel bottom plate of size 300x300x10mm thickness & also inbuilt service window of 300 mm x 100 mm at 800 mm above the base plate on existing cement concrete pedestal as required with a heavy duty 4 way connector including earth connector & 6 A SPMCB. Pole& brackets dimension is 145x82x3mm thick. Logo and name of the manufacturer shall be embossed on the pole. The pole should be primer coated and PU painted. As per diagrams attached. Double arm bracket of size 1000 mm long with high lumen LED module made out of pressure diecast aluminum with polycarbonate diffuser attached (2x60 W) , with 1600 mm spacing between the brackets at top I P rating IP 66 a) Total System Wattage=120W +/- 5% b) Luminous efficacy >= 100 Lm/w ( c ) Power factor >= .95 with minimum 03 years warranty on LED lights and accessories etc. (LED light and Driver – Superior Make), |
| 15 | Providing and laying in position M25 grade reinforced cement concrete foundation of size 450 mm (L) ×450 mm wide and 1000 mm deep i/c excavation of earth, providing cutting, bending and placing in position, reinforcement of cold twisted bars of 12 mm dia- 960 mm long(approx)-8 nos. and reinforcement of cold twisted bars of 8 mm dia- 1400 mm (approx) -6 nos.(with 150 mm spacing) as required with supplying and positioning of 4 nos. foundation bolts16 mm dia,600 mm long, J type i/c 2 nos. template anchor plates of size 225mm ×225mm× 3mm and providing DCW HDPE for cable entry and exit as req. for 3 m and 5 mtr pole. |
| 16 | Providing and fixing of Stainless steel name plate of size 6×8 sq inch made of 20 gauge sheet including engraved name of area representative duly painted along with SS clamp nut bolt etc req. |
| 17 | Providing and Fixing name board made of MS Sheet 90x60 cm , 1mm thick with frame of MS angle 50x50x6mm, two diagonal braces at the back of the sheet of MS flat 40x6mm, total height of the board above groundlevel 2.40m, length of legs below ground0.30m embeded in CC block 1:2:4(1 cement : 2 coarse sand: 4graded stone aggregate 20mm nominal size) 30x30x45cm including excavation and removal of surplusearth with in 50m lead, applying primary coat of approved steel primer, painting with synthetic enamel point of approved quality and lettering with enamel paint of approved colour (one side)as per drawing /direction of Engineer in charge. |
| 18 | Supply of XLPE insulated PVC sheathed Un -Al. Conductor Armoured Cable 1.1KV grade conforming to IS-7098 of following size: a) 2C x 4 sqmm |
| 19 | Supplying and fixing of 32 mm dia X 1.00 metres long G.I. pipe (medium class) bracket for mounting of fluorescent / HPMV / HPSV street light fitting on pole including bending the pipe to the required shape, 2 nos 25mm X 6 mm flat iron clamps with nuts, bolts and washer, painting the flat iron with primer and finish paint etc. as required |
| 20 | Supplying, installation, Testing & Commissioning of Street light LED fixture, powder coated pressure die cast aluminum body with built in or separate driver as per the requirement with Driver efficiency >85%, Input voltage: 140-270 Volt AC, freq 50/60 hz, Operating temp range -15 deg to 50 deg centigrade, internal surge protection of 5 KV L,N,E as per IEC 61000-4- 5, Driver efficiency >85%,THD < 10% as per IEC 61000-3-2 , P. F.≥0.95, IP- 66,IK-10, CRI >80 , under voltage and over voltage protection,EMIEMC as per CISPR-15, lenses for beam angle as per IESNA type I/II/III as per the width of theroad and the project requirement., suitable to fit in up to 65mm dia pipe, life time (LED,Driver & electrical circuitry) of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends as per LM80 extrapolation IES TM-21-11 report , CCT 3000°K / 4000°K / 5700°K /6000°K/6500°K (As per ANSI Bin) , SDCM(Standard Deviation Color Matching) <5, Maximum power consumption should notmore than the specified rating and Fixture shall be of relevant BIS standardcomplete in all respect i/c connections with 1.5 sq mm FRLS, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy >135 lm/Watt output . LM79 & LM80 Test report from NABL lab for all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal management: heat sink of aluminum housing such that LED junction temperature shall not rise above 90°C). 72 Watt |
| 21 | Fabrication, supplying and fixing class B galvanised double overhang arm bracket made out of 250mm long galvanised top tube with cap and 250mm long 32 mm dia galvanised pipes with tightening bolts complete as required. |
| 22 | Supplying, installation, Testing & Commissioning of Street light LED fixture, powder coated pressure die cast aluminum body with built in or separate driver as per the requirement with Driver efficiency >85%, Input voltage: 140-270 Volt AC, freq 50/60 hz, Operating temp range -15 deg to 50 deg centigrade, internal surge protection of 5 KV L,N,E as per IEC 61000-4- 5, Driver efficiency >85%,THD < 10% as per IEC 61000-3-2 , P. F.≥0.95, IP- 66,IK-10, CRI >80 , under voltage and over voltage protection,EMIEMC as per CISPR-15, lenses for beam angle as per IESNA type I/II/III as per the width of the road and the project requirement., suitable to fit in up to 65mm dia pipe, life time (LED,Driver & electrical circuitry) of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends as per LM80 extrapolation IES TM-21-11 report , CCT 3000°K / 4000°K / 5700°K /6000°K/6500°K (As per ANSI Bin) , SDCM(Standard Deviation Color Matching) <5, Maximum power consumption should notmore than the specified rating and Fixture shall be of relevant BIS standardcomplete in all respect i/c connections with 1.5 sq mm FRLS, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy >135 lm/Watt output . LM79 & LM80 Test report from NABL lab for all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal management: heat sink of aluminum housing such that LED junction temperature shall not rise above 90°C). 40 Watt |
| 23 | Fabrication, supply & erection of 5.0 mtr height, 3 mm thick, bottom dia of 130mm & top dia of 70mm base plate of size 225 x 225 x 12 mm thick flange mounted hot dip galvanized octagonal pole made from HT steel plate,window with flash cover with full vertical window cover at appropriate height from the base plate on existing cement concrete pedestal as required. i/c supplying and fixing of 6 mm thick laminated mounted sheet inside the window mounted on and i/c providing and welding 3 nos. GI strips 4 mm thick of suitable length and having suitable size tapped holes as reqd, terminal block suitable for 25 sq mm conductor – 4 nos. & shorting links on DIN channel i/cpdg and fixing DIN channel of suitable length,, 6 Amp. SPMCB ‘C’ characteristics, earth stud, cable support clamp suitable for upto 4x25 sqmm cable. Logo/Name of manufacturer shall be embossed or riveted plate on the pole. Galvanization as per relevant IS. code ect as required. |
| 24 | Part BComprehensive annual malntenance of 50 watt IP65 decorative single plece LED fixtures with die cast aluminum housing frosted PMMA / PC diffuser, suitable for upward mounting with power LEDS white/warm white fitted with suitable extruded aluminum heat sinks, high voltage protection and suitable constant current LED driver extra as required. Technical Particulars 1) Size of fitting 580mm X 340mm, base section inner dia- 64mm and outer Dia-71mm 2) Total Power of light Fixture - 50 Watt 3) Input voltage-AC 120 to 270volt 50Hz 4) Power Factor .0.95 5) Minimum lumen output of LEDs - 100 Lumen per watt 6) Luminaire protection - IP65 (After Standard Warranty of 2 Years)a)Rate for 3 year |
| 25 | b) Rate for 4 Year |
| 26 | c) Rate for 5 Year |
| 27 | Comprehensive annual malntenance ofzig zag arm(After Standard Warranty of 3 Years)a) Rate for 4 Year |
| 28 | b) Rate for 5 Year |
