|
| 1 | Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable (5Mtr long) in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. |
| 2 | Wiring for group controlled (looped) light point/fan point/exhaust fan point/call bell point ( without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit,and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required. |
| 3 | Supplying and fixingtwo module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required. |
| 4 | Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.25 mm |
| 5 | Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required. |
| 6 | 3 x 2.5 sq. mm |
| 7 | 3 x 4 sq. mm |
| 8 | Fan HookInstallation, Testing, Commissioning of wall/ Ceiling bracket /ceiling fittings of all sizes and shapes containing upto two GLS/CFL/LED lamps per fitting, complete with all accessories including connections etc. as required. |
| 9 | Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable, including providing and fixing phenolic laminated sheet cover on the fan box etc. as required. |
| 10 | Supplying and fixing 3 pin, 5 A ceiling rose on theexisting junction box/ wooden block includingconnections etc. as required. |
| 11 | Supplying and fixing TPN sheet steel enclosure onsurface/ recess along with 16/25/32 A 415 V \"C\"curve TPN MCB complete with connections, testingand commissioning etc. as required. |
| 12 | Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.. |
| 13 | Supplying and fixing 6 modules, Plastic suface box along with modular base , cover plate & with 2 nos.15/16 A -6 pin modular socket with controlled by 2 no. 16 Amodular switches with allinterconnection in switch board by 2.5 sq. mm PVC FRLS grade wire, termination with copper lugs , all complete and as per instruction of EIC. etc as required.Make: Legrand (Moisac) |
| 14 | Installation ,Testing, Commissioning of 12 W white cool LED suface mountedfittings, complete with all accessories including connectionsetc. as required. |
| 15 | Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube/lamp etc. directly on ceiling/ wall, including connections with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required. |
| 16 | Supply, installation, testing, commissioning of road Post Top LED luminaries complete with mounting pole, PCC foundation with plaster finish, control gear/termination fixture, lamp. All control accessories/termination accessories, internal wiring, painting and two coats of bituminous compounds, preservatives below ground level etc. for the fallowing as per drawings.Specification and as per the instruction of the Ingineer-In-Charge. |
| 17 | GI pole 3.00 Mtr. Long Steel Tubular Poles made of 114.3 mm O. D x 4.50 mm thick pipe as per IS :1161/2713/1239 with loop-in slot door (80 x 130 mm) type JB with 2 nos. flat & allen key bolt, foundation type base plate (300 x 300 x 12), Nipple ( 100 mm long made of 60.3 O.D Pipe) & Stiffener ( 4 nos.) Foundation Bolt (M 24 x 500 mm- 4 nos) with IP 67 protection and provision of terminal for mounting MCB and provision for incoming and outgoing cables to pole JB. Painting of pole with two coats of red oxide primer and two coats silver coloured paint and as per specifications, drawing and instruction of Engineer-In-Charge. |
| 18 | Post Top Ring LED Light fittings 30/45 W of M/s. Philips / Bajaj / Halonex / Evereaday make and its control gear accessories etc. complete. Scope also includes internal wiring with 3 nos. of 2.5mm.sq. copper conductor PVC wires from terminal box at bottom of the poleto fixture. |
| 19 | Earthing of above G.I. pole with 2 nos. of 8 SWG G.I.earth wires each 8 Mtrs long coiled in one metre dia at a depth of 1400mm. Below ground level, complete with soldering end connections with sockets, 3/8\" dia 1\" long GI earthing bolt fully threaded & welded on pole etc. all as per drawings, specifications and as per the instruction of EIC. |
| 20 | M.V. CABLE: Supply, installation, testing & commmissioning of 1.1 KV grade PVC insulated, inner sheath PVC tapped, extruded outer sheath PVC , G.I. srtip/wire armoured, multistranded alluminium conductor power cable conforming to IS-1554 PART-I with upto date ammendments. Laid 900mm below final ground level including excavation in all type of soil including hard murrum and soft rock temporary reintsatement sand bedding,covering cable on top and side with baked bricks conforming to IS-1077back filling of trench and removal excess earth within a radious of 500 mtrs.4 C X 10mm PVC cable strip armoured and stranded conductor. |
| 21 | End jointing of 4C X 10mmsq. PVCA aluminium power cable by crimping with supply of all jointing material like solderless copper socket, insulation tape, flux, cable gland etc. and all as per instruction of EIC. |
