|
| 1 | Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in hard/ dense soil comlete all as specified and directed. |
| 2 | Excavating over areas, in following depth and gettingout in hard/dense soil complete all as specified and directed :- |
| 3 | Depth not exc 1.5m deep |
| 4 | Depth exc 1.5m but n\"exc 3.0m deep |
| 5 | Excavating in trenches nexc 1.5 m width and n exc 1.5 m in depth for foundation etc or for shafts, well cesspits, manholes etc / for laying of cable/ pipe etc nexc 10 sqm on plan and nexc 1.5 m in depth and getting out in hard/dense complete all as specified and directed. |
| 6 | M&L for PCC (1:4:8) Type D2 (using 40 mm graded stone aggre-gate) as in foundations, filling and mass-concrete complete all as specified and directed. |
| 7 | M&L for formwork to rough finish to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to battercomplete all as specified and directed. |
| 8 | M&L for formwork to rough finish to sides of pillars, posts, struts, piers, columnssquare,rectangular or polygonal and stanchionscomplete all as specified and directed. |
| 9 | M&L for formwork to rough finish to sides and soffits of floor or roof beams, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etccomplete all as specified and directed. |
| 10 | M&L for mild steel TMT bars as in reinforcement, 10mm dia and over cut to length, bent to shape required including cranking, bending hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. |
| 11 | M&L for mild steel TMT bars 5 to 10mm dia bars as in stirrups cut to length, bent to shape required including cranking, bending hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. |
| 12 | M&L for RCC (design mix) M-25 (using 20mm graded stone aggregates) as in Foundations, including rafts, footings, foundation beams; plinth beams, bases for columns, etc. basement slabs, under-reamed piles, raft etc and mass concrete complete all as specified and directed. |
| 13 | M&L for RCC (design mix) M-25 (using 20mm graded stone aggregates) as in columns, pillars, piers, posts and struts complete all as specified and directed. |
| 14 | M&L for RCC (design mix) M-25 (using 20mm graded stone aggregates) as in floor/ roof beam, cantilevers, lintel over 1.5m span complete all as specified and directed. |
| 15 | M&L for brick work with old size full bricksubclass ‘B’ burnt clay bricks, straight or curved on plan exc 6m mean radius, built in CM (1:6) complete all as specified and directed. |
| 16 | M&L for 5 mm thick plastering on fair faces of brick or contretesurfaces, in CM (1:3), surface finished even and smooth without using extra cement complete all as specified and directed. |
| 17 | M&L for 10 mm thick plastering on fair faces of brick or contretesurfaces, in CM (1:6), surface finished even and smooth without using extra cement complete all as specified and directed. |
| 18 | M&L for 10 mm thick plasteringon other than fair faces of brick or contretesurfaces, in CM (1:6), surface finished even and smooth without using extra cement complete all as specified and directed. |
| 19 | M&L for preparing newly plastered surfaces of wall and applying two coats ofcement base paint over a coat of cement primer complete all as specified and directed. Note :-The newly plastered surface must be prepared in a manner so that there should not be any impression of dent and it should be made even and smooth all as per satifaction of Engr-in-Charge. The cost of all materials, T&P and labour required for preparation of surface are deemed to be included in the rates quoted. |
| 20 | S&F mild steel work as in hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts, posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc and similar work conforming to Fe-290 Gde E-165 steel with and including necessary drilling holes etc complete all as specified and directed.Note: The unit rate quoted by contractor is deemed to be inclusive of cutting to dead lenth where required, notching, drilling, fitting, rivetting and/or welding or connecting with bolts and nuts (including rivets or bolt and nuts), providing and fiitings angle cleats, fish plates, gusset plate etc., also for welding plumbing, truing up and fixing complete. No claim whatso ever shall be entertained by Govt on this account. |
| 21 | S&F galvanised, 2 strand, steel barbed wire 2.24 mm dia barbed with 2 mm dia barbs at 75 mm spacings and straining and fixing to any type of standard rails straining bolts , including,securing or tying at crossings with and Provision of galvanised mild steel wire, staples or steel pins etc. as directed ( each line wire to be measured)complete all as specified and directed. |
| 22 | M&L for twocoats of synthetic enamel paint over a coat of red oxide primer including preparation of new steel surface over 10cm width or grith complete all as specified and directed. |
| 23 | M&L galvanised Concertina coil duly stretched maintaing a dia of 600 mm concertina coil placed in Y shape angle iron post erected over boundry wall and fixed to angle iron with 3 mm dia GI bearer wire as per IS 4454 Part I typically has a length of approximately 10 to 12 meter when fully extended. This length is achived with 50-60 loops complete all as specified and directed. |
| 24 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm.complete all as specified and directed. |
| 25 | Removal of surplus soil to a distance exc. 250 Mtr but n exc. 500 Mtr and depositing where directed at a level not exc 1.5m above the starting point complete all as specified and directed. |
| 26 | Excavating in post holes (or similar holes) in hard/ dense soil, each n.exc 0.5 cum, getting out and removing surplus soil to a distance n.exc 50 m and making good surface complete all as specified and directed. |
| 27 | M&L for PCC (1:3:6) Type C2 (using 40 mm graded stone aggregate) as in foundations, filling and mass-concretecomplete all as specified and directed. |
| 28 | S&F Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt exc 5cm but n exc 10cmlong and 5 to 10 mm dia of neck complete all as specified and as directed. |
| 29 | Supply only chain link MS galvanised fencing size 50x50 mm mesh 3.8 mm dia complete all as specified and as directed. |
| 30 | Fixing only chain linkfencing including line wires, any mesh, size and type to any type of standards,rails,straining bolt etc,including provision of binding wire complete all as specified and as directed. |
| 31 | M&L for mild steel round bars10mm dia Fe 290 (Gde E-165) and over cut to length, bent to shape required including cranking, bending hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. |
| 32 | M&L for two coats of synthetic enamel paint over a coat of red oxide primer incl preparation on new steel surface n.exc 10 cm width or girth complete all as specified and directed. |
| 33 | M&L preparation of new or previously untreated steel and iron, surfaces of any description exceeding 10cm in width or girth and applying two coat of black bituminous paint over a coat of red oxide primer complete all as specified and as directed. |
| 34 | Supply and FixingXLPE insulated AB Cable 1100 volts 3 core x 50 Sqmm (insulated phase conductors) + 1x 25 Sqmm (Insulated support/ nuetral conductor) for street light connections ISI marked on 09 mtr LT steel tubular poles complete all as specified and directed. |
| 35 | Supplying, laying, commisioning and testing of 1.1 KV grade XLPE insulated PVC sheathed steel armoured aluminum stranded conductor LT UG cable ( Conforming to IS 7098)ISI marked of size 50 sqmm 3.5 core complete all as specifed and directed. |
| 36 | S&F insulation piercing connectors (IPC) for main/service/street light connections for cable of 16-95 Sqmm with taps ranging from 10-95 Sqmm IPC type 002 complete all as specified and directed and conforming to relevant IS. |
| 37 | S&Fcable end cap for cable 50 Sqmm three core +25 Sqmm one core and conforming to relevant IS complete all as specified and directed. |
| 38 | S&Fsuspension clamp with aluminium alloy bracket stainless steel strap, buckles, eye hook incl nuts and bolts and washers confirming to relevant IS complete all as specified and directed. |
| 39 | Supply and fixanchoring clamp with aluminium alloy bracket stainless steel strap, buckles, eye hook incl nuts and bolts and washers confirming to relevant IS complete all as specified and directed |
| 40 | S&Fof steel tubular swaged poles completeas per IS-2713 MS base plate of size 300mmx300mmx6mm , final taper plug, bolts, nuts and screws as specified type 410 SP-31 (9 mtr long) includingnecessary earth work and excavation, PCC in foundation 1:4:8 type D-2, using 40 mm graded stone aggregate and PCC 1:3:6 type C-2, using 40 mm graded stone aggregate as in plinth block, disposal of surplus soil to a distance not exceeding 50 m, painting two coats of aluminium paint over one coat ofred oxide primer including 3 Nos band/straps with yellow and black colour in alternatete way (200mm wide each)enamelled paint two coat at a distance 300mm from plinth block and marking pole nos with blackenamelled paint including tarring one coat on steel surface embedded in concrete complete all as specified and directed. NOTE : Required earth work and PCCwill be paid eparately under relevnt items of Sch A |
| 41 | Supply & fixing stay assembly complete with all accessories, such as stay plate 300x300x6mm, stay rod 215cm long and 16mm dia with nuts including GI Bow turn buckle etc, all as per Electrical Plate No 1 SSR-2009 Part-I complete all as specified and as directed. |
| 42 | M&L for sand cushioning for under ground cable with layer of fine river dry sand 80 mm thick before laying of cable and 150 mm thick after laying of cable in trenches complete all as specified and directed by Engg-in-Charge. Note:- Punned (consolidated ) thicness of sand will be measured and paid. |
| 43 | M&L for cable protection bricks common burnt clay sub class B designation 75 for protectioon of UG Cable laid in trenches complete all as specified and directed. |
| 44 | M & L, PCC (1:2:4) type B1 (using 20mm graded stone aggregate) as in mass concrete/coping complete all as specified anddirected. |
| 45 | Supply and fixingbracket made out of 32mm bore, steel tubings,galvanised, light grade not less than 1.2 mtr long bend to shapewith all fitting including fixed on pole with 02 Nos MS Clamp made out of FI 32x6mmcomplete all as specified and as directed. |
| 46 | Supply and fixnew LED street/security light fitting 60W housing made out of pressure die-cast aluminium alloy with toughned glass, IP-66 protection, working on 240 Volts , 50 HZ, consisting of reflective lens wired with appropriate driver PF>0.90 made up of long life LED chips (SMD) in modular luminior efficiancy > 110 Lumens/watt including connecting with 1.5 sq mm, 3 core, PVC insulated Copper conductor cable 1100 Volts grade from pole box to light or from overhead conductor to light complete all as specified and as directed by Engr-in-Charge. |
| 47 | S & F Loop in and Loop out FRP rectangular SMC junction box(Pole Box) front openable hinged from side of size 200x140x95 mm suitable for outdoor installation weather proof having 4 pole cable connector (for cable in and out junction) fixed inside box with insulator support complete for street light fitting with MS clamps of suitable size and GI nuts, bolts and washers complete all as specified and directed. |
| 48 | Supply, install and testing LT Feeder pillar panelcubical outdor type front hinged openable door including locking arrangement, platform mounted with angle iron 40mmx 40mmx 5mm frame work suitable for 240 volts grade three phase 4wire 50 HzAC Supply system, having bus bar chamber with suitable aluminium bus bar 100 Amp rating and accomodated with 32 Amp MCB TPN,contactor of 40 Amp rating with digital 24 Hrtimer and making all necessay electrical connection complete, the box shall be dust and vermin proof IP-54 class protection alongwith in built short circuit protection confoms to IS/IEC 60947-4-1 complete all as specified and directed . |
| 49 | Material & labour for earthing complete with galvanised steel earth plate electrode 600x600x6mm thick burried directly in ground. ( earth pit not less than 2.25 mtr depth below ground level at any type of strata ) with top edge of the earth plate not less than 1.5mtr below normal ground level connected by 4 mm GI wire as earth lead by means of brass nuts and bolt,thimbles check nuts, washers including concrete chamber of PCC 1:3:6 type C-1 using 20mm graded stone aggregate with fair finish, internal surface of concrete chamber shall be given internal dia 300mm x300mm, 15mm thick plaster in CM 1:4 funnel with wire mesh, RCC pit cover of 320x320x80mm size (1:2:4) Type B1 using 20mm graded stone aggregate rainforced with XPM and charcoal, dust and common salt all as shown in electrical plate No 3 of MES SSR Part-1(2009) and specified including and provision of GI wire upto 7.5 mtrs long with 15 mm dia medium grade Gi pipe protection and watering pipe of GI 20 mm bore, medium grade, including all excavation and earth work and connecting the earthing strip to panel, including testing on completion complete all as specified and directed by Engr-in-charge. Note:- (i) RCC pit cover shall be precast of RCC(1:2:4) type B1, 80mm thick rainforced with XPM weighting not less than 4kg/sqm in lieu of CI cover.(ii) Cost of additional GI wire more than 7.5 mtrs will be measured and paid seperately under relevant items. |
| 50 | Material & labour for earthing complete with galvanised steel earth plate electrode 600x600x6mm thick burried directly in ground. ( earth pit not less than 2.25 mtr depth below ground level at any type of strata ) with top edge of the earth plate not less than 1.5mtr below normal ground level connected by using galvanised iron strip 25×4mm as earthing lead by means of brass nuts and bolt,thimbles check nuts, washers including concrete chamber of PCC 1:3:6 type C-1 using 20mm graded stone aggregate with fair finish, internal surface of concrete chamber shall be given internal dia 300mm x300mm, 15mm thick plaster in CM 1:4 funnel with wire mesh, RCC pit cover of 320x320x80mm size (1:2:4) Type B1 using 20mm graded stone aggregate rainforced with XPM and charcoal, dust and common salt all as shown in electrical plate No 3 of MES SSR Part-1(2009) and specified including and provision of GI wire upto 7.5 mtrs long with 15 mm dia medium grade Gi pipe protection and watering pipe of GI 20 mm bore, medium grade, including all excavation and earth work and connecting the earthing strip to panel, including testing on completion complete all as specified and directed by Engr-in-charge. Note:- (i) RCC pit cover shall be precast of RCC(1:2:4) type B1, 80mm thick rainforced with XPM weighting not less than 4kg/sqm in lieu of CI cover.(ii) Cost of additional GI wire more than 7.5 mtrs will be measured and paid seperately under relevant items. |
