|
| 1 | Demolition work of brick work |
| 2 | Demolishing brick work manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-Charge.In mud mortar |
| 3 | Demolition work Interlock |
| 4 | Taking out existing CC interlocking paver blocks from floors, footpath/ central verge, including removal of rubbish etc., disposal of unserviceable material to the dumping ground, for which payment shall be made separately and stacking of serviceable material within 50 metre lead as per direction of Engineer-in-Charge. |
| 5 | Chipping of old Plaster |
| 6 | Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. |
| 7 | Earth work excavation |
| 8 | Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge.All kinds of soil |
| 9 | Filling available earth |
| 10 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m. |
| 11 | Red earth filling |
| 12 | Filling with contractor own earth (excluding rock) in open areas in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m as per direction of site Engineer-incharge. |
| 13 | Bailing of water |
| 14 | Pumping or Bailing out water and removing slush etc by using pump set (approx. 5HP) including cost of labour, oil hire charges of pumpset, etc complete |
| 15 | Shoring |
| 16 | Close timbering over areas including strutting, shoring and packing cavities (wherever required) etc. complete ( Measurements to be taken of the face area timbered): |
| 17 | Soling for footing |
| 18 | Soling with rough stone of size 200 mm, well packed and filling voids with stone chips and required profile with hammer dressed stones having no side less than 15 cm, with minimum depth of 20 cm including preparing the bedding surface etc. all complete |
| 19 | PCC works |
| 20 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 21 | RCC works below plinth |
| 22 | Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 23 | RCC work above plinth level |
| 24 | Reinforced cement concrete work in lintel, beams, columns, pillars, slabs, shades, staircase, short columns, fillets, plinth and string courses, etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size.) |
| 25 | Steel reinforcement |
| 26 | Steel reinforcement for R.C.C work including straightening,cutting,bending,placing in position and binding all complete after applying 2 coats of zinc rich primer.Supply of steel reinforcement will be in the scope of contractor.Thermo mechanically treated bars of grade Fe-500D or more of approved brand as per the instruction of engineer in charge |
| 27 | Centering and shuttering for foundations, footing, etc |
| 28 | Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete |
| 29 | Centering and Shuttering works beam, lintel, etc |
| 30 | Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders bressumers and cantilevers |
| 31 | Centering and Shuttering works for roof slab, shade, etc |
| 32 | Centering and shuttering including strutting, etc. and removal of form for:Suspended floors, roofs, landings, balconies and access platform |
| 33 | Centering and Shuttering works for columns |
| 34 | Centering and shuttering including strutting, etc. and removal of form for:Columns, Pillars, Piers, Abutments, Posts and Struts |
| 35 | Black anti- corrosive bitumastic paint for raft |
| 36 | Painting with black anti- corrosive bitumastic paint of approved brand and manufacture to give an even shade:Two or more coats on new work |
| 37 | Solid Block Masonry below plinth level |
| 38 | Solid block masonry using pre cast solid blocks (Factory made) of size 30x20x20cm or nearest available size confirming to IS 2185 part I of 1979 for foundation and plinth with thickness 20cm and above in: CM 1:6 ( 1 cement : 6 coarse sand ) etc complete |
| 39 | Solid block masonry for wall |
| 40 | Solid block masonry using pre cast solid blocks ( Factory made) of size 30x20x20cm or nearest available size confirming to IS 2185 Part I of 1979 for super structure up to floor two level thickness 20cm and above in: CM 1:6 ( 1 cement : 6 coarse sand) etc complete |
| 41 | Plastering works |
| 42 | 12 mm cement plaster of neat cement of mix:1:4 ( 1cement : 4 fine sand) |
| 43 | Tiling works |
| 44 | Supply and laying first quality vitrified digital size 600 x 600mm or nearest size tiles of approved shade and pattern for floors as per architectural design laid with cement mortar 1:4 (1 cement : 4 course sand ) conforming to IS: 15477, in average 3 mm thickness with tile spacer and jointing with with epoxy joint fillers with pigment of matching shades of approved brand in approved pattern with two or more design complete of make Kajaria/Cera/johnson/somany or other approved brand. (All materials shall be arranged by the contractor) |
| 45 | GI Truss work |
| 46 | Steel work in built up GI tubular (round, square or rectangular hollow tubes etc.) trusses etc, including cutting, hoisting, fixing in position and applying a priming coat of approved epoxy primer and 2 or more coats of epoxy paint, including welding and bolted with special shaped washers etc. complete |
| 47 | PVC roofing sheet |
| 48 | Providing & fixing PVC corrugated roofing sheets (thickness 2mm or above) of good quality up to any pitch, including ridges, fixing with zinc phosphate poly coated hooks, bolts & nuts 8mm dia G.I plain/ bitumen washers complete but excluding the cost of purlins, rafters, trusses etc. The sheets shall be opaque or translucent, clear or pigmented, textured or smooth as specified. |
| 49 | Supplying and fixing UPVC rainwater gutter (Euro guard, Aquastar or Supreme) with metallic bracket supports as per manufactures specification |
| 50 | Providing and fixing UPVC rain water gutter of approved brand and shape, 160mm size with required slope using self drilling/ self tapping screws complete, fixed with gi clamp at 1m spacing |
| 51 | PVC Downpipes of approved brand |
| 52 | Providing and fixing PVC pipes including fixing the pipe with clamps/clips at 1.00 m spacing. This included jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 75 mm dia 6Kgf/cm2 - External work- Exposed on wall |
| 53 | PVC bend 75 mm |
| 54 | Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 75 mm dia Bend |
| 55 | Coupling 75 mm |
| 56 | Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 75 mm dia Socket /coupling. |
| 57 | Corner drop 75 mm |
| 58 | Providing and fixing UPVC end d rop for rain water gutter of approved brand, size and shape fixed with necessary screws and sealant |
| 59 | Centre drop 75 mm |
| 60 | Providing and fixing UPVC center d rop for downpipes for rain water gutter of approved brand, size and shape fixed with necessary screws and sealant |
| 61 | Aluminium frame work |
| 62 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS : 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminnium snap beading for glazing /paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing, paneling and dash fasteners to be paid for separately): For fixed portionPowder coated aluminium (minimum thickness of powder coating 50 micron) |
| 63 | Aluminium Shutter |
| 64 | For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately)Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 65 | Glass for windows |
| 66 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm) |
| 67 | Hylam Sheet |
| 68 | Providing and fixing 4 mm thick hylam sheet in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of Engineer - in- Charge |
| 69 | Butt Hinges |
| 70 | Providing and fixing IS : 12817 marked stainless steel butt hinges with stainless steel screws etc. complete:100x58x1.90 mm |
| 71 | Handles |
| 72 | Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete:100 mm |
| 73 | Paint Emulsion including primering |
| 74 | Finishing walls with Premium Acrylic Smooth exterior/interior paint with Silicone additives of required shade:New work (Two or more coats applied @ 1.43 ltr/ 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm) |
| 75 | Miscallenous Labour |
| 76 | Miscellaneous labour Please Enable Macros to View BoQ information |
