|
| 1 | Supply, installtion, testing and commissioning LT panel board, 415 Volt 3 phase, 4 wire, AC 50 Hz, cubical, indoor type, Pre-wired, floor mounted weather and vermin proof, size 1100 x 900 x 450 fabricated out of 2.0 mm thick CRCA MS sheet and angle iron frame40x40x6 mm, with bus chamber and seperate in built sheet metal cubicles for accessaries including hinged panels opening from front,spray painted with two coat synthetic enamelpaint over a coat of red oxide primer of shade and tint as approved, suitable cable glands, thimbles for all incoming and out going cables including grouting of panel board on PCC (1:2:4) foundationusing 20 mm graded stone aggregate all as per approved drawing and as specified and directed consisting of the following:-Note Drawing of the panel shall be approved by garrison engineer before placing order.4 Nos bus bar / wire high conductivity aluminium alloy, properly insulated and colour coded, 03 Nos for phases (RYB) rating 400 Amps and 01 No neutral connected with incommer MCCB 250Amps and outging MCCBs 63 Ampsand duly supports complete all as directed.MPCB,3 pole, 32 Amps,415 VoltAC, suitable for 10-15 HP Motor capacity - 03 NoPower contactor 3 phase, 415 volt 25 Amps MNX series - 09 NosThermal over load relay suitable for 20 to 33 Amp current rating, MN 12 type- 03 no Analog / Digital timer suitable for star delta starter - 01 No Make : Single Phase perventer, phase reversible with under voltage, over voltage preventer relay - 01 no Volt meter digital type, 3 phase AC, 96 mm square type,0- 500 Volt, including selector switch for reading on all three phases - 03 No.Ammeter digital type, 3 phase AC,96 mmsquare type0- 100 Amp with selector switch andCTs of suitable size- 03 No.Phase indicating lamp with holder 230 V AC with toggle switches / MCB - 09 NosNote for item no 1- All items / components / accessories which are useful and necessary for efficient working of the starter panel shall deemed to be included in the item irrespective of the fact whether such items are specifically mentioned in it or not. |
| 2 | M & L for assembling, installation, Lifting / lowering of bore wellSubmersible pump set assembly of capacity 70-80 Hp in existing bore well after carrying out necessary repair / replacement work including connecting column pipes, line shaft with guide spiders and rubber bushes etc. duly installation, commissioning and connected with hollow shaft electric motor or submersible of any capacity including making all necessary adjustments and electric connections as required for satisfactory performance of the pump complete all as specified and directed. Notes: (i) All type of T & P andtransport is to be arranged by the contractor for lifting andlowering of the Pump sets. (ii)All electrical connection of the motor shall be removed and then connected very carefully with th help of suitable joint and insulation tape . (iii) Spare parts will be measured and paid separatly in respective schedule as supply only item |
| 3 | Re-developing of tube well by means of high velocity compresed air by pumping muddy water and clean the borewellup to satisfaction of JE E/M / Engineer-in -charge complete all as specified and directed |
| 4 | Yield test for borewell by contineous pumping for 12 hours with their own pump of contractor,to determine safe yield and testing of water from AMC state deptt for its potability complete all as specified and directed(Note payment of water testing made by contractor is deemed to be included in the quotated rate. |
| 5 | M&L for packing withgravelof suitable size all around of the casing of required depth up to level complete all as specified and directed |
| 6 | Supply & Fix / Welded 10 mm thick mild steel flanged duly drilled for fixing 03 Nos nut bolts & washers rubber gasket suitable to be fixed 100 / 125 / 150 mmbore existing mild steel column pipe with and including welding of three Nos 150 mm long 40x6 mm flat iron pieces one side with flanged and other side with column pipe complete all as specified and directed |
| 7 | Supply & Making column pipe with Mild steel cold ERW column pipe 100 mm bore, 10 feet long, 7.20 mm wall thick and threading upto 80 mm from end including supply & fix / welded 10 mm thick mild steel flanged both ends duly drilled for fixing 04 Nos nut bolts & washers and fixing nut bolt of size75 long & 12mm dia with 02 nos washer and suitable size of rubber gasket, including welding of three Nos 150 mm long 40x6 mm flat iron pieces one side with flanged and other side with column pipe complete all as specified and directed. |
| 8 | Supply, Installed & fix maintenance free earthing copper bonded steel earth rod of 10 feet long having diameter of 17.2mm with copper bonding thickness of 250 micron with universal clamp made of SS earth enhancing compound shall be of 30kg/pit(resistivity is less than 0.12 Ohm meter).The bove arrangements shall be provided with heavy duty earth poly plastic pit cover of 4000 kg load bearing capacity (Size:270 x 40 200mm) complete all as specified and directed. |
| 9 | Supply &Fixing Earth continuty conductor or main earthing lead fixed to wall on batten or recess chases or buried in ground or drawn in conduit /pipe or fixed to poles or any other loop earthing etc. as required 25X4mm galvanised iron strip complete all as specified and directed |
| 10 | Supply and fixing of cast iron sluice valve class PN-1.6ISI marked, both ends flanged, stainless steel spindle, with iron wheel and necessary jointing materials, nuts & bolts, washers etc for making two flanged joints of following sizes as required with taking down old U/S valve:- |
| 11 | 150 mm bore |
| 12 | 200 mm bore |
| 13 | Taking up cast iron / DI pipe line (including all fittings) with spigot and socket ends and lead joints including burning out joints and recovering lead for the following bore of pipes:- |
| 14 | 100 mm bore |
| 15 | 150 mm bore |
| 16 | Supply ,laying jointing,commissioning and testing Ductile iron pipe with spigot and socket end centrifugally cast(spun) classK-7 conforming to IS-8329-2K in any length laid intrenches including rubber tighten joint as required at site complete all as specified and directed of followingsize :- |
| 17 | 100 mm bore |
| 18 | 150 mm bore |
| 19 | Excavating in trenches in Hard / dense / soft soil, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation of poles, trenches for laying of cable, etc. and getting out complete all as specified and directed. |
| 20 | Removing excavated material to a distance not exceeding 50 Mtr and deposting where directed at a level not exc. 1.5 mtr above the starting point. |
| 21 | Returing filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm each all as required and directed. |
| 22 | Supply and fixing DI fittings like Ductile iron bends (any type, radius and angle) tapers any type (straight, bend, increasing, decreasing or double socket etc)tees pieces single branches, ‘Y’ junction, double branch cross including jointing materials on line(all sockets or socket & spigot)collar, caps and plugs etc upto 200 mm bore size complete all as specified and directed |
| 23 | Supply and fix in replacementPVC braided pipe (Hose pipe) heavy duty 50 mm bore for suction in sewage line complete all as specified and directed |
| 24 | Supply and fix in replacement Renewal of PVC braided pipe (Hose pipe) heavy duty 150 mm bore for suction in sewage line complete. |
| 25 | Supply and fix in replacement Renewal of PVC braided pipe (Hose pipe) heavy duty 100 mm bore for suction in sewage line complete all as specified and directed |
| 26 | Supply and install Hand operated chain pully blocks heavy duty including chain of capacity 3 Ton ,15 mtr length suitable for existing sewage pump motor complete all as specified and directed.. |
| 27 | Supply and fix in replacement PVC insulated PVC sheathed copper conductor flexible cable water /oil proof suitable for non clog sumersible pump set ,size of 10 core 1.5 sqmm multistranded dewatering cable including of good making of water proof epoxy joint at motor termination as required. |
| 28 | M&L in replacement 100 mm dia non return (reflux) valve with Gun Metal working parts cast iron body including jointing material complete all as specified and directed. |
| 29 | Supply & Fix / Lowering PVC insulated and PVC sheathed flexible, flat, nominal size 25 Sqmm 1100 volts grade, ISI Marked three core, stranded copper conductor cable complete all as specified and directed. |
| 30 | Supply & Fix / Lowering PVC insulated and PVC sheathed flexible, flat, nominal size 35 Sqmm 1100 volts grade, ISI Marked three core, stranded copper conductor cable complete all as specified and directed. |
| 31 | Supply and fixing suction sweeper complete with stainless steel body,movable trolley,pump of capacity 2 hp including DOL starter of suitable capacity complete with three core workshop copper cable of 1.5 sqmm from main panel to starter installed on trolley, complete all as specified and directed(Note cost of pump,starter,trolley and copper cable is deemed to be included in quotated rate by the contractor in this schedule. |
| 32 | Supply and fixing swimming pool suction head of size 24\"\",plastic body suitable for suction sweeper as per item no 25 above complete all as specified and directed. |
| 33 | supply and fix swimming pool hose pipe heavy duty 50mm bore dia suitable for suction sweeper as per item no 25 above complete all as specified and directed. |
| 34 | supply and fix swimming pool telescopic pole suitable for suction sweeper as per item no 21 above complete all as specified and directed. |
| 35 | supply and fix swimming pool leaf net bag of standard size complete all as specified and directed. |
| 36 | supply and fix swimming pool ball brush of size 16\"\" ,plastic bodycomplete all as specified and directed. |
| 37 | supply and fix swimming poolalage brush of size 16\"\"complete all as specified and directed. |
