|
| 1 | Draining of Old Oil from RGB & filling with Gear oil GX-90 - 8 Ltr, Cleaning Gear train by removing old Grease & Applying M.P. Grease grade no. 150 - 10 Kg to Gear train, Pedastal, Drum axle,Trunion pin, Locking box and Lifting bracket pin etc. and refilling of oil of Radial gate of 20 MT cap hoist -1 No., including cost of material, sundry material and labour charges with leads & lifts at site etc complete, as per drawings, specifications and or instructions concern in charge. all as specified & directed. |
| 2 | Dismantalling & Replacing old damaged Brake Liner 200 mm Ø - 1set by new one of 20 MT Cap Hoist of Radial Gate, including cost of material, sundry material and labour charges with leads & lifts at site etc complete, as per drawings, specifications and or instructions of concern in charge. |
| 3 | Dismantalling & Replacing old damaged Brake Coil - 1 No set by new one (200 mm Ø ) of 20 MT Cap Hoist of Radial Gate, including cost of material, sundry material and labour charges with leads & lifts at site etc complete, as per drawings, specifications and or instructions of concern in charge . all as specified & directed |
| 4 | Dismantaling & Replacing old damaged Brake Drum (200 mm Ø) Rubber bushes & Bolts - 6 Nos each by new one of 20 MT Cap Hoist of Radial Gate, including cost of material, sundry material and labour charges with leads & lifts at site etc complete, as per drawings, specifications and orconcern in charge. all as specified & directed. |
| 5 | Dismantaling & Replacing old damaged ICTP Switch 16 Amp 415V with neutral link - 1No (as per Specification) by new one of 20 MT Cap Hoist of Radial Gate, including cost of material, sundry material and labour charges with leads & lifts at site etc complete, as per drawings, specifications and or instructions of concern in charge. all as specified & directed |
| 6 | Dismantling of old damaged side rubber seal from gate leaf of R.G 12 x 4 m - 1No. Supplying & fitting new L type side rubber seal confirming to IS 11855-1986 (Updated) size 90x15x65x18 - 4.94 mtr and G.I. bolt M-20x90 - 49 Nos and dismantling of old damaged Bottom rubber seal from gate leaf of R.G. 12 x 4 m -1No. Supplying & fitting new flat type bottom rubber seal confirming to IS 11855- 1986 (Updated) size 90x15 mm - 12.2 mtr and G.I. bolt M20x80 - 97 Nos with double washer including cost of material, sundry material and labour charges with leads & lifts at site etc completeas per drawings, specificationsand orinstructions of concern in charge. all as specified & directed |
| 7 | Cleaning of Drain Holes of Horizontal girder, End arm assembly, Locking box etc, of R.G. 12x 4 m - 1 No by way of removing rust, dust slurry, any other foreign particles etc , including cost of material, sundry material and labour charges with leads & lifts at site etc completeas per drawings, specifications and orinstructions of concern in charge. |
| 8 | Dismantalling & Cleaning of Track Roller - 4 Nos of stoplog Gate 12 x 1 Mtr - 1 No. and refitting with M. P. Grease - 4 Kg & Damaged \"O\" Ring - 12.00 Mtr., including cost of material, sundry material and labour charges with leads & lifts at site etc complete, as per drawings, specifications and or instructions of concern in charge (05 Nos Of Gate Leafs.)04 x 05 = 20. all as specified & directed |
| 9 | Dismantaling of damaged side rubber seal and Bottom rubber seal from gate leaf of stoplog gate of size 12 x 1 m -1 No, on Maintenance Platform and fitting new Hollow type side rubber seal confirming to IS11855 / 1986 and G. I. Bolt with Double Washer and Nut with satisfactory test & trial. , including cost of material, sundry material and labour charges with leads & lifts at site etc complete, as per drawings, specifications and or instructions of concern in charge(05 Nos Of Gate Leafs.) all as specified & directed |
| 10 | Handling charges of one piece of 12 x 1 Mtr Stoplog gate for repairs to radial gate considering lowering, lifting & stacking on platform / on storing arrangement , including cost of material, sundry material and labour charges with leads & lifts at site etc completeas per drawings, specifications and or instructions of concern in charge ( No of Stoplog 05 nos opration for 8 stoplog gate 4 times = 5x 4 = 20). all as specified & directed |
| 11 | Removing Old Cardium Compound of wire rope of 20 MT cap hoist -1 No .Dia 24 mm - 75 Mtr length in 4 No of falls, into Wire rope socket - 4 Nos,by cleaning Agent, Applying new Cardium Compound (Servocoat 140) - 14 Kg. including cost of material, sundry material and labour charges with leads & lifts at site etc complete, as per instructions of concern in charge (Actual Fall of 18.75 mtr x 4 x 2) = 150 mtr. all as specified & directed |
| 12 | Removing Old Cardium Compound of wire rope (100 Mtrs) of 25 MT cap Goliath Crane - 1 No. &gate , by cleaning Agent, Applying new Cardium Compound (Servocoat 140) - 14 Kg. including cost of material, sundry material and labour charges with leads & lifts at site etc complete, as per drawings, specifications and or instructions of concern in charge. |
| 13 | Draining of Old Oil from RGB - 3 Nos. (O:600 - 1No. & O:400 - 2 Nos.) Filling with new gear oil GX 90 - 21 Ltr, Cleaning Gear train by removing old grease, Applying M.P. Grease - 8 Kg to Gear train, Pedastal, Drum axle. etc to 25 MT Goliath crane - 1 No. , including cost of material, sundry material and labour charges with leads & lifts at site etc complete, as per drawings, specifications and or instructionsconcern in charge |
| 14 | Dismantaling and Replacing old damaged Electric Starter 10 HP - 1No (as per Specification) Air Break Reversing Contractor Type Having 3 Built in Push ButMTs With Over Load Protection of Bimetal Relay by new one of 25 MT Cap Hoist. , including cost of material, sundry material and labour charges with leads & lifts at site etc complete, as per drawings, specifications and or instructions of concern in charge. |
| 15 | Dismantalling and Replacing old damaged Brake Drum Rubber Bushes and Bolts of Coupling - 18 No. (200 mm Ø - 3 set) by new one of 25 MT Cap Goliath Crane. , includingcost of material, sundry material and labour charges with leads & lifts at site etc complete, as per drawings, specifications and or nstructions of concern in charge. |
| 16 | Dismantalling and Replacing old damaged Equilizer bracket assembly - 2 Nos by new one of 25 MT Cap Goliath Crane. including cost of material, sundry material and labour charges with leads & lifts at site etc complete, as per drawings, specifications and or instructions of concern in charge(Excluding material charges. |
| 17 | Bearing 2316 + H2316+SN610 |
| 18 | Bearing 1210 K+ H12106+SN570 |
| 19 | Bearing, Sleeve & Pedestal No. 2217K +H317 + N517 |
| 20 | Bearing6212 |
| 21 | Bearing6216 |
| 22 | Bearing22222E |
| 23 | ShaftRear 35.4 kg |
| 24 | ShaftFront 45.5 kg |
| 25 | E.M. Brake Dia.300 mm- 12\" (415 VAC,2Ф) 1+5 v l Gate |
| 26 | Painting Area of Goliath |
| 27 | Supply and fix in repairs PVC insulated and FR PVC Round Sheathed, Copper Conductor (flexible) industrial cable, size of 3 core x 4 sqmm, 1100 Volt, conforming to IS 694 including making all connections at site and testing all as specified and as directed. |
| 28 | Supply and fix in repairs PVC insulated and FR PVC Round Sheathed, Copper Conductor (flexible) industrial cable, size of 3 core x 6 sqmm, 1100 Volt, conforming to IS 694 including making all connections at site and testing all as specified and as directed. |
| 29 | Demolition of Concrete of any description and in any position not otherwisespecifically provided for |
| 30 | M&L Providing Cement concrete in roof kerb or mud stops,rounded or chamfered on edges mm graded (12.5 mm) aggregate type B0 1:2:4 in roof kerbs or mud stops, rounded or chamfered on edges |
| 31 | M&L earthing complete with galvanized steel plate electrode 600 mm x 600 mm x 6 mm thick, burried directly in ground vertically in pit of depth not less than 2.25 metre below normal ground level with top edge of the earth plate at a depth not less than 1.5 metre below normal ground level surrounded from all sides with mixture of charcoal and common salt in alternate layers and electrode connected to galvanized iron strip 25mmx4 mm size by means of GI bolts, nuts, check nuts and washers, earth strip protected by galvanized steel pipe 40 mm bore (light grade) connected to main switch board or any other electrical equipment all as shown in electrical plate No. 3 of SSR-2009 Part I and includingnecessary excavation and earth work in any type of soil, 20 mm bore medium grade GI pipe for watering, funnel with wire mesh, PCC (1:3:6), type C-1 chamber, RCC (1:2:4), type B-1, reinforced with 6 mm dia MS round bars @ 15cm c/c both way for cover and MS frame etc., complete all as specified NOTE: The unit rate includes earth strip and protection pipe upto (maximum 7.5 metre from earth plate) earth point/test point. |
| 32 | M&LGalvanised iron strip 32 x 6 mm buried in ground means of GI bolts, nuts, check nuts and washers, earth strip. |
| 33 | Dismantling of motor7.5 HP 3 phase 415 volts, 50 Hz from the pump set and repairs to motor by taking out burnt out winding completely without damaging to the other parts cleaning slots and M & L for rewinding with new super enamelled copper wire of appropriate gauge and number of turns etc complete and heat varnishing including replacement of DE/NDE and reassembling and refixing in the same location and testing for its proper functioning complete all as specified and as directed. |
| 34 | All as per item No23.00 above but 5 HP motor. |
| 35 | Supply and fill Lubricant oil MAK HYDROL 68 (In cane of 5 Ltrs each) suitable for VT PumpMake Mak Lubricantor equivalent |
| 36 | Supply and Filling only compressor oil suitable for Elgi make compressor Make Indian oil or equivalent |
| 37 | M&LCastrol premium long life grease suitable for craneor all eqiument all as specified and directed. |
| 38 | Repair/maintenance of Bridge & Cross Traverse rail alignment by taking corrective action, clamps fitting/ adjustment all as specified and directed. |
| 39 | Repaire/maintenance and replacement DSL or I/P supply cable on LT all as specified and directed. |
| 40 | Supply & fixing in repair of Current collector all as specified and directed. |
| 41 | Repair/replacment of Bridge wheel assembly defective part; any of wheel, bearing, spacer, shaft, coupling, brake, gearbox all as specified and directed. |
| 42 | Repair/replacement of Trolley/Crab wheel assembly defective part; any of wheel, bearing, spacer, shaft, coupling, brake, gearbox all as specified and directed. |
| 43 | Repair/replacement of Hoist assemblydefective part; any of coupling,bearing, spacer, shaft, gear. all as specified and directed. |
| 44 | Repair/maintenance ofHoisting Brake shoes all as specified and directed. |
| 45 | Repair/Maintainance of Equiliser pulley defective parts; any of pulley, shaft, bearings all as specified and directed. |
| 46 | Repair/Maintainance forSpan & Diagonals of crane, at its position all as specified and directed. |
| 47 | Supply & fixing in repair of Rubber Buffers all as specified and directed. |
| 48 | Repair/Maintainance of Limit switch for any of motion ( long travel/cross traverse/hoisting ) all as specified and directed. |
| 49 | Repair/Maintainance of any of part / buttons of Pendent with it\"s support rope/chain all as specified and directed. |
| 50 | Supply & fixing in repair of Pendent 10 core cable all as specified and directed. |
| 51 | Repair/Maintainance Electrical control panel cables all as specified and directed. |
| 52 | Repair/Maintainance of VFD ( Variable frequency drive ) for any motionall as specified and directed. |
| 53 | M&L in repair of Relay and Contactor with accessories all as specified and directed. |
| 54 | Repair/Maintainance of General minor accessories of electrical panel all as specified and directed. |
| 55 | Supply & fixing in repair of wire rope dia 12mm by ISO certified and tested new wirerope all as specified and directed. |
| 56 | Colouring of crane bridge, crab, end carriages and platform with yellow color epoxy, asian paint all as specified and directed. |
| 57 | EOT crane- Testing, Inspection & Certification by Chartered Engineer ( with load test ) |
| 58 | Taking down old header & Fabbricate ,Supply &,installed MS header made out of 16 mm thick ms sheet with internally epoxy coated paint of size 3 metre 8 inch dia & 3 metre in length, wash out valve size 50 mm, 1.5 x 1.5 feet foot cap, and inlet 150 mm dia -3 Nos and out let 150 mm dia -03 Nos, with perssure release vave all as specified and directed by Engg-In-Charge. |
| 59 | Takingup or downMS Pipes Heavy Grade with all fittings ,flange and nut bolts etc laid in floors or fixed to walls and ceilings etc of size 150 mm |
| 60 | -do- but 80 mm dia |
| 61 | -do- but 100 mm dia |
| 62 | Supply and lay MS Pipes Heavy Grade with all fittings ,flange and nut bolts etc laid in floors/piller or fixed to walls and ceilings etc of size 150 mm |
| 63 | -do- but 80 mm dia |
| 64 | -do- but 100 mm dia |
| 65 | Excavation in trenches not exc.1.5 m wide and not exc 1.5 m depth for taking out and laying of water pipe line and getting out in soft/loose soil complete all as specified and directed. |
| 66 | Returning filling in trenches including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as directed. |
| 67 | Removing of excavated material not exc 50m and depositing where directed at a level not exc 1.5 m above the starting point complete all as specified and directed. |
| 68 | Supply and fix in repair/ installation and testing of cast iron sluice valve,heavy duty class-I, ISI marked, conforming to I S 14846, long body type, pressure type PN-1.6,flanged ends and drilled having brass steel spindle with iron head wheel at the top complete with and including nuts, bolts, washer, rubber gasket and jointing complete all as specified and directed of following sizes:- |
| 69 | 80mm bore |
| 70 | 100mm bore |
| 71 | 150mm bore |
| 72 | 250mm bore |
| 73 | Taking out the existing unserviceable NRV of any make/model andsupply and fix new NRV ( ISI Mark)of CI body threaded/flanged end, drilled of both ends of PN-1flap type without by pass arragement all as required at site including nut/bolts and fixing in position including provn of rubber gasket nut bolt etc all as specified and directed by Engr-in-Charge of the following sizes:- |
| 74 | 80mm |
| 75 | 100mm |
| 76 | 150mm |
| 77 | 250 mm bore |
| 78 | Taking up existing CI/DI water mains (including all fittings), with spigot and socket ends and lead joints including from exacavated trenches, burning out joints and recovering lead joints for the dia 250 mm. |
| 79 | Supply and in trenches, in repar, in any length centrifugally cast (spun) ductile iron (DI) pressure pipes, class K-9 classification, suitable for push on type rubber gaskits joints testing size of the 250mm dia bore complete all as specified as directed. |
| 80 | M&L for Bends (any type, radius and angle) tapers any type, (straight, bend, increasing, decreasing or double socket etc.) Tee pieces single branch. \"Y\"junction, double branch, cross (all sockets or socket and spigot) collars, caps and plugs upto 150 mm to 300mm. |
| 81 | M&L Cross arms, bracings, supports,clamps and back plates fabricated from structural steel sections including nuts, bolts, washers,welding, bending cold or hot,drilling holes for bolts, in any shape or size as indicated or directed andinclusive of one primer coat, one under coat and one finishing coat of paint |
| 82 | Note: Amount of sch of credit of Rs.85,090/-will be deducted from total amount of BOQ. |
