|
| 1 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises incl removal of debris to out side defence land complete all as specified and directed. |
| 2 | M&L for Non skid ceramic coloured tiles 7 to 8mm thick (square/ rectangular) area of each tile exc 0.11 sqm but not exc 0.18 sqm in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match, over and incl screed bed or bedding layer of mortar 15mm thick for laying floor finishesin CM (1:6) complete all as specified. |
| 3 | M&L for Non skid ceramic coloured tiles 7 to 8mm thick (square/ rectangular) area of each tile exc 0.18 sqm but not exc 0.38 sqm in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match, over and incl screed bed or bedding layer of mortar 15mm thick for laying floor finishes in CM (1:6) complete all as specified. |
| 4 | Description all as per item No. 03.00 above but on vertical surfaces such as skirting / dados, over and including 10 mm thick CM 1:4 as in backing coat complete all as specified. |
| 5 | M&L for Glazed ceramic coloured tiles in vertical surfaces 600 x 300 x 7mm thick set and jointed in neat cement slurry and pointed with white or coloured cement mixed with pigments to match, over and incl rendering/ backing coat 10mm thick CM (1:4) in dado/skirting tiles complete all as specified and directed. |
| 6 | Dismantling of stone slabs and tiles of any description or thickness in floors, aprons etc. laid, bedded and pointed in any mortar and removal of debris to out side defence land complete all as specified and as directed. |
| 7 | M&L for 18 to 20mm thick Granite (of any type) work (table rubbed and polished)in steps, jambs, pillars, window cills, cooking plateforms, dado/wall and like over and incl 15mm thick cement mortar 1:4, screed bed including pointing in white cement mortar 1:2 using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed. |
| 8 | M&L for Machine cut kota stone slab flooring 22-25mm thick, over and incl cement screed 15 mm thick in CM (1:6) base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing (Mirror), complete all as specified and directed. |
| 9 | M&L for Machine cut kota stone 15 to 18mm thick in riser of steps, skirting, dado and pillar over and incl 10mm thick rendering in CM (1:4) cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing (Mirror), complete all as specified and directed. |
| 10 | Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations |
| 11 | M&L for Mirror polishing on marble/ granite/ Kota stone/ stone work where ever required to give high gloss finish complete. |
| 12 | Dismantling of old cabinet, cupboard/ wardrobe complete all as specified and as directed. |
| 13 | M&L for Modular kitchen & Wardrobe / cupboardwith 18 mm thick one side decorative and other side balancing lamination factory pressed HDHMR Board levies of action Tesa and equivalent including 2 mm thick PVC edge banding tape with hot glue by edge bending machine etc with auto closing spring loaded hinges (hydraulic type) etcor sliding with track arrangement as directed including necessary accessories like stainless steel handle, Magnetic catch etc including all necessary fittings and fixture and8mm thick both sides PrelaminatedBSB (Both side balancing proper ) HDHMR of Action Tesa and equivalent as per IS:14587:1998 fixed. |
| 14 | S&F in repair fancy type 15mm bore Stop valves, cast copper alloy, screwed down, high pressure, withcrutch or butterfly handle, screwed both ends foriron pipe orfor unions and fixed. |
| 15 | S&F in repair 15mm bore dia CP Bib taps, cast copper alloy with crutch orbutterfly handle, screwed down, screwed foriron pipe or for brass ferrule and fixed complete all as specified and directed. |
| 16 | S&F in repair 15mm bore dia Sink Cock with Regular Swinging Spout (Wall Mounted Model) With Wall Flange complete all as specified and directed. |
| 17 | S&F in repair CP brass Tubular towel rail 20mm dia. |
| 18 | S&F in repair CP brass brackets for above item No 17.00. |
| 19 | S&F in repair Soap dish, any type, fixed to plugs with chromium plated brass screws. |
| 20 | S&F in repair PVC connection 15mm dia and 600 mm long with 2 Nos PTMT nuts complete. |
| 21 | S&F in repair vitreous ChinaSquatting pan \"Orrisa\" pattren size 580x440mm white with integral foot rest incl lean concrete, complete all as specified and directed. |
| 22 | S&F in repair PVC valveless, 10 ltr syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets |
| 23 | S&F in repair PVC (SWR) floor trap, plain with grating (waste hole/plain type) including jointing with solvent cement, 75 to 100 mmmm diameter of outlet, all as specified. |
| 24 | Taking up or down 15mm dia steel tubing and connection incl cleaning for refixing or removal to store. |
| 25 | S&F for GI tubing medium grade galvanised with all fittings and fixed complete to walls and ceiling or laid in floors 15 mm dia bore. |
| 26 | S&F in repair looking mirror of selected quality sheet glass 5.5 mm thick designerwith chromium plated brass screw and cup washer complete all as specified and directed. |
| 27 | S&F in repair sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 535mm x 460mm bowl size 460mm x 385mm x 205mm. |
| 28 | S&F in repair 15 mm bore dia Pillar taps (High Neck), cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered \"Hot\" or \"Cold\" with long screwed shanks and fly-nuts, screwed for iron pipe and fixed. |
| 29 | S&F in repair sinks double bowl made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 1155mm x 515mm bowl size 510 x 410 x 255 mm. |
| 30 | S&F in repair Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) |
| 31 | S&F in repair Vitreous china urinal partition white of size 310x700 mm |
| 32 | S&F in repair 32mm waste coupling PTMT for urinal, (Minimum weight 32mm-45gms) |
| 33 | S&F in repair Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms) |
| 34 | Demolition and breaking up drain pipes (SGSW, AC, PVC or reinforced cement) set in cement mortor internal dia of pipe 75 to 100 mm complete all as specified and directed. |
| 35 | S&F of 110 mm bore SWR pipes single socketed in any length with rubber ring joints laid in trenches or in floors etc complete all specified and directed. |
| 36 | S&F of 110 mm bore SWR pipes single socketed in any length with rubber ring joints fixed to walls complete all specified and directed. |
| 37 | S&F of 75 mm bore SWR pipes single socketed in any length with rubber ring joints laid in trenches or in floors etc complete all specified and directed. |
| 38 | S&F 110 mm bore PVC (SWR) bends complete all as specified and directed. |
| 39 | S&F 75 mm bore PVC (SWR) bends complete all as specified and directed. |
| 40 | S&F 110 mm bore PVC (SWR) vent cowl complete all as specified and directed. |
| 41 | S&F 110 mm bore PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and directed. |
| 42 | S&F for stack clampsout of 50 mm by 5 mm flat iron and 16 mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or rooffor 100 mm bore of pipe complete all as specified and directed. |
| 43 | Taking down cement plaster, any description on brick or stone or cement concrete walls including raking out joints, hacking for key, scrubbing down with water etc. |
| 44 | M&L for 15 mm thick cement plaster in cement mortar 1:6 on brick or concrete surface etc. on wall finished even and fair extra cement, all as specified . |
| 45 | M&L for 5 mm thick cement plaster in cement mortar 1:3 on brick or concrete surface etc. on ceilingfinished even and fair without using extra cement, all as specified. |
| 46 | M&L for Washed stone grit plaster on exterior walls in two layers, under layer 12mm cement plaster 1:4 (1 cement: 4 coarse sand ) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3 Kg of cement per square metre, top layer 15mm cement plaster 1:1/2:2 (1 cement: 1/2 coarse sand : 2 stone chipping 10mm nominal size) in panels with groove all around as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the stone chippings complete all as specified (Payment for providing grooves shall be made separately). |
| 47 | M&L for Forming groove of uniform size 15mm wide and 15mm deep in the top layer of washed stone grit plaster as per approved pattern using wooden battens, nailed to the under layer including removal of wooden battens, repair to the edges of panels and finishing the groove complete as per specifications and direction of the Engineer-in-charge. |
| 48 | M&L for preparation of newly plastered surfaces of wall and applying two coats of distemper oil emulsion over and incl 1mm thick wall care putty and one coat of primer all as specified. |
| 49 | M&L for preparation of newly plastered surfaces of ceiling and applying three coats of white wash complete all as specified. |
| 50 | M&L for complete removal of existing treatment on ceiling surface and applying two coats of white wash complete all as specified. |
| 51 | M&L for complete removal of existing treatment on wall and applying two coats of distemper oil emulsion over and incl 1mm thick wall care putty and one coat of primer all as specified. |
| 52 | M&L for complete removal of existing treatment on wall and applying two coats of cement base paint over and incl 1mm thick exterior wall care putty and one coat of primer all as specified. |
| 53 | Preparation of old painted wood or wood based surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint,complete all as specified and as directed. |
| 54 | Preparation of old painted steel surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint,complete all as specified and as directed. |
| 55 | Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided complete all as specified. |
| 56 | M&L for 75mm thick cement concrete 1:3:6type C2 using 40mm graded stone aggregate as in plinth/sub base incl making joints, Complete all as specified. |
| 57 | M&L for Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand;complete all as specified. |
| 58 | S&F in repair fancy type Curtain rods decorative type stainless steel 25mm nominal dia of approved quality(Make VISTA) (1mm wall thickness)including fixing oftwo number decorative brackets fixed in brick/concrete wall, Two number of latto on both ends of curtain rods complete all as directed and specified. |
| 59 | Dismantling wrought iron or mild steel work of any description not otherwise provided |
| 60 | S&F for Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete Fe 410-W (Gde E- 250) quality A complete complete all as directed and specified. |
| 61 | M&L for preparing new Steel surfaces of any description over 10cm width or girth and applying two coats of synthetic enamalle paint over a coat of red oxide zink chrome primer. complete all as specified and as directed. |
| 62 | Taking down chowkats or frames with shutters(without taking offshutters from frames) areanot exceeding 1.50 sqm each complete all as specified |
| 63 | Taking down chowkats or frameswith shutters(without taking offshutters from frames) area exceeding 1.50 square metre andnot exceeding 4.0 square metre each complete. |
| 64 | Taking down shutters of any description area exceeding 1.00 square metre andnot exceeding 2.0 square metre each complete. |
| 65 | S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet re-inforced with MS square tube in opening as per specification and shown on drg SSR Part-II. |
| 66 | S&F, factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails MS frame shall be covered with heat moulded plain cover PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for styles and plain colour PVC sheet for top rails lock rail and bottom rail on either side & as gap insert for top rail and bottom rail paneling of plain colour PVC sheet to be fitted in MS frame welded/sealed to the styles and rails with suitable PVC sheet beading and jointed together with solvent cement coplete as per specification and shown on drawing SSR Part-II (2020). |
| 67 | S&F for Flush shutters 30mm thick, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed. |
| 68 | Glazed and skeleton shutters (2nd class soft wood) 35mm thick, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats |
| 69 | S&F for Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples |
| 70 | S&F in repair for Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples |
| 71 | Preparation of new wood or wood based surfaces of any description over 10cm width or girth and applying two coat of synthetic enamel paint, over a coat of primer complete all as specified and as directed. |
| 72 | S&F MS butt hinges 100mm long medium weight cold rolled mild steel etc |
| 73 | S&F aluminium anodised barrel tower bolts of extruded section with 150 mm long bolt, all as specified . |
| 74 | S&F Extruded aluminum alloy handle,fabricated type,anodized 125mm size. |
| 75 | S&F Extruded aluminum alloy handle,fabricated type,anodized 150mm size. |
| 76 | S&F Aluminium alloy, anodised, sliding door bolt 300mm long, with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts & sliding bolts of extruded sections or cast aluminium alloy complete. |
| 77 | S&F Floor door stopper of aluminium alloy body and tongue, anodized, with hard drawn steel fixed in floor with over all length of cover plate 140 mm fixed complete. |
| 78 | S&F MS 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete. |
| 79 | Hacking out old broken glass (any thickness size, quality or description) from wooden/ steel frames glazed with putty or fixed with wooden beads/metal pins complete. |
| 80 | M&L for 5.5 mm thick Sheet glass, ordinary quality and glazing with beads in square not exc 0.5 sqm in each pane complete all as specified and directed. |
| 81 | S&F for Figured glass, pin head type and glazing with oil putty in squares not exc 0.5 sqm in each pane 5.00mm thick all as specified |
| 82 | Excavation in trenches not exc 1.5m wide and not exceeding 1.5 mtr in depth for foundation etc shaft, cesspits, manholes sewage line etc not exc. 10 Sqm on plan and getting out complete all as specified and directed. |
| 83 | Returning, filling in, trenches with soil in layers not exc 25 cm thick, watering and well ramming complete all as specified and directed. |
| 84 | Removal of surplus soil to a distance not exc 50 mtr away & deposting where directed at a level not exc 1.5 mtr above the starting point complete all as specified and directed. |
| 85 | Demolition and breaking up old unserviceable salt glazed stoneware pipe 150mm bore at any depth set in cement morter incl PCC bed complete all as specified and directed. |
| 86 | M&L for PCC 1:4:8 type D-2(using 40mm graded crushed stone aggregates) bedding forsewage lines of 150mm bore incl packing under and haunching against the sides of pipe after they are laid and tested complete all as specified and directed. |
| 87 | Supply and fixed class SN-8, dia of pipe 150mm & thickness of pipe as specified in IS 16098 (Part-2):2013, clause 6.3.1 table no 5 structured wall polythelene piping system (pipe with online/offline coupler and elastomeric sealing ring) with non smooth external anular corrugated and smooth internal surface (double wall) for non pressure underground sewerage & drainage application polythylene piping fitted with help of coupler attached with one end of pipes, sliding over the elastomeric sealing rubber ring placed on the specified valley of the corrugation at the spigot end, lowering the same into the trench, laying at prescribed gradient, depth and alignment, testing the water tightness of the joint, ensuring the continuity tests of the specified pipe segments etc including all necessary fittings (cost of fittings, rubber rings, gaskets etc includded) complete all as specified and directed by Engineer-in-charge. |
| 88 | S&F Precast Plastic fibre reinforced concrete manhole cover (medium duty) of size 900mm x 450mm x 80mm confoming to IS- 12592incldemolition of old RCC cover , complete all as specified and directed. |
| 89 | S&F Precast Plastic fibre reinforced concrete manhole cover (medium duty) of size 600mm x 600mm x 80mm confoming to IS- 12592incldemolition of old RCC cover , complete all as specified and directed. |
| 90 | Demolition of brick work/stone boulder measonary built in cement mortar or cement lime mortar of any description and in any position all as specified. |
| 91 | M&L for brick work in CM (1:4) straight or curved on plan exc 6.0m mean radius and using old size sub class \"B\" bricks all as specified. |
| 92 | Removing building materials etc. (other than spoil payable under items 03028 to 03031 in Section-3—Earthwork) to a distance of 100m or under, beyond the lead included in the rates, including loading, unloading and stacking at the destination |
| 93 | Taking down/ out carefully copper/aluminium point wiring for light/fan/bell/ sockets 5/15 Amps complete without accessories as switches,Sockets, holders,ceiling roses,light fitting regulators etc (to be measured separately) and making good the disturbed surface all as directed. |
| 94 | M&L for point wiring complete with 1.5 Sq mm (nominal area) FRLS, PVC insulated un-sheathed and stranded copper conductor cable ISI marked drawing in PVC concealed conduit and PVC conduit fitting including drawing FRLS, PVC insulated unsheathed 1.5 Sqmm copper earth wire, connecting to common earth dolly with and incl Metal flush box of suitable size with sheet for fixingswitches/sockets/fan regulator etc complete all as directed for the following :- |
| 95 | One light point / fan point/ wall fan point/ bell/ buzzer controlled by one 1-way switch/ bell push. |
| 96 | One socket outlet point 5 amps on the independent board. |
| 97 | Description all as per Srl Item No 94.00 here-in-before but with 4 sq mmFRLS copper wire with 4 Sqmm FRLS copper earth wire for independent point. |
| 98 | Switch piano flush type, 6 Amp one way,SP, 230 volts AC, complete all as specifed and as directed. |
| 99 | Switch piano flush type, 16 Amp one way,SP, 230 volts AC, complete all as specifed and as directed. |
| 100 | Socket outlet 6 Amp 5 pin, complete all as specifed and as directed. |
| 101 | Socket outlet 6&16 Amp 6 pin, complete all as specifed and as directed. |
| 102 | S&F in replacement Ceiling rose, insulated body, 3 terminal, 240 volts, 5 Amps and making good surface as original by plastering and whitewash/ colour/ distemper etc complete all as directed. |
| 103 | S & F surface and wall mounted LED tube light fitting with polycarbonate housing & interated electronic driver with tube rod of 20 Watt. slim elegant design.and including connected with 3 core 23/0.0076 insulated copper wire from celing rose to fittting connector all as specified and directed. |
| 104 | Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300 mm and depositing the old U/s item to MES store yard. |
| 105 | Supply and installation, commissioning and testing of Modern Flying Insect Killer Stainless steel 304 grade with 02x18 watt UVA lamp, single phase, 220 V, 50 HZ, made out of MS/CRCA sheet, Ultra voilet based attraction, wall mounted/Hanging type,GI wire grid with tray,and based upon light intensity approx 300-400 sqft, complete with fittings and accessories and depositing the old U/s item to MES store yard.all as specified and as directed. |
| 106 | Supply and installation, commissioning and testing of commercial Air curtain unit for prevention of dust and conditioned air losses, single phase, 220 V, 50 HZ, made out of MS/CRCA sheet of minimum thickness 18 gauge finished with two coats of red oxide primer and final coat of synthetic enamel paint (oven baked) with MS - CRC 18 gauge square perforated suction grills, Aluminium alloy fans and single phase electric motor, nozzles etc, complete with fittings and accessories so as to produce 1 - 1.5 m/sec air velocity at floor level for door opening and depositing the old U/s item to MES store yard. all as specified and as directed. |
| 107 | S & F energy efficicent LED fittings 45W LED 6K suitable for builing security light pressure die cast aluminium roadway luminaire with high power LEDs and HF electronic driver complete all as directed. |
| 108 | Supply and fixing in replacement of street light fitting bracket, 1.0 mtr long bent to shape made out of galvanized iron pipe of 25 mm dia size light grade complete with nut, bolts, washer, clamps etc inclusive of one primer coat, one under coat and one finishing coat of silver paint complete all as directed. |
