Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | NOTE (Applicable for all items) :-(i) The bidders/contractorsare advised to read tender document & all corrigendum / amendments and General conditions of contracts before entrying/quoting the rates.2. It is highlighted that the certain condition of General Condition of Contracts (IAFW-2249) has been modified as per direction of MoD i.e. inclusssion of Performance Security, deletion of Risk & Cost Provisions and increase in defect liability period all as per tender documents. The tenderers should keep in mind while quoting their offer. |
| 2 | Demolition of old existing unserviceable roof treatment included cement concrete of any description and in any position from existing roof surface (upto maximum height of 10 metres from natural ground level) with power driven pneumatic chisel and including removal of debris and washing down with water to remove dust, foreign items complete all as specified and directedcomplete all as specified and directed |
| 3 | M&L for prepartion of old surface and applying two coat of latex power bonding agent at the ratio of 1:4:6 (Latex power:Water:Cement) in a criss cross way complete all as spd and directed by Engineer- in-Charge. Note :- Second coat of latex is laid down minimum interval of 6-8 hours of first coat of latex and after second coat of latex immediate applied plaster work. |
| 4 | M&L for 40 mm thick average PCC1:2:4 type B-0 (12.5 mm graded aggregate) as in padding concrete on roof with chicken wire mesh all as directed by Engineer- in-Charge. |
| 5 | M&L PCC(1:2:4) type B-0 (using 20mm graded aggregate) as in roof kerbs or mud stop rounded |
| 6 | M&L for rendering 10mm thick on fair faces on roof surfaces of concrete surfaces in cement mortar 1:3 finished even and fair includingusing water proofing compound admixture as per manufacturer\"s instructions,complete all as specified and directed.Note :- WPC will measuered and paid separatly under relevant item of schedule. complete all as specified and directed. |
| 7 | M&L for providing water proofing treatment with a layer of APP based polymeric membrane 3mm thick minimum weighing 3.60kg/sqmreinforced with polyster non wove fabric (wt. not less than 160 gms/sqm) shall be applied over one coat of cold bituminous primer @ 0.40 ltr/sqm (membrane shall be laid using butane torch sealing all joints etc, complete all as specified and directed.(Note :- The over lap shall be of minimum 75mm in longitudinal direction and 100mm on transverse direction ) complete all as spd and directed). |
| 8 | M&L for two coat of aluminium paint over APP membrane complete all as specified and directed. |
| 9 | Dismaltaling of plain or corrugated steel sheeting , any gauge, thickness, including nainital or similar pattern roof coverings complete all as specified and directed. |
| 10 | S & F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as complete all as specified and directed. |
| 11 | Dismantling of cascade with all completing fittings and fixtures complete all as specified and directed. |
| 12 | Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed. |
| 13 | Material and labour for steel work in tubular Post/columns including special shaped washer , truss purlins etccomplete using ERW or induction butt welded tubes conforming to IS-1161-1979 grade ST-240, complete all as specified and directed. Note :- The rate included for any type/any design of steel membercomplete all as specified and directed. |
| 14 | Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 5cm but n exc 10cm longand dia 12mm complete all as specified and directed. |
| 15 | S & F Mild steel bolts with diameter of neck exc 12 n.exc 20mm purpose made. with hexagonal or square head one end and screwed the other, or screwed both ends; each screwed end to be fitted with washers and one hexagonal or square nut. Exc 30cm long complete all as specified and directed. |
| 16 | Dismantling to carefully remove existing floor/wall tiles, including mortar/backing, ensuring minimal damage to underlying concrete. All removed tile and adhesive material to be systematically collected and transported off‑site to an approved dumping area in accordance with Engineer-in-Charge’s instructions. |
| 17 | Providing and applying waterproofing treatment by chemical injection grout approved adhesive Intraplast added 1% by weight of cement and grouting construction joint as per site conditions including drilling holes and fixing injection ports at appropriate spacing and grouting chemicals mixed with neat cement slurry complete with cutting & sealing of the packers as per specification. The supplier must have their own manufacturing facility, should not be private label product or sourced from third party. The manufacturer must be an ISO 9001 & 14001 certified and valid certificates must be produced as proof and Cleaning the reinforced concrete surface or shotcrete surface or blind side surface to make it aggregate, dust and sludge free, removing any extended portions by grinding using suitable equipments. The substrate to be made suitable for waterproofing system application. |
| 18 | Providing and applying approved adhesiveready to use grey cement based polymer modified tile adhesive for wall and floor tile fixing application in a minimum of 4 mm thickness. The tile adhesive must conform to C2TE according to EN 12004-2. The adhesive supplier must have their own manufacturing facility, should not be private label product or sourced from third party. The manufacturer must be an ISO 9001 & 18001 certified and valid certificates must be produced as proof complete all as specified and directed. |
| 19 | Providing and applying approved adhesive Grout EP, epoxy waterproof coloured tile joint filler in a width of 3 mm. The grout supplier must have their own manufacturing facility, should not be private label product or sourced from third party. The manufacturer must be an ISO 9001 & 18001 certified and valid certificates must be produced as proof complete all as specified and directed. |
| 20 | M&L for non skid vitrified designer mosaic Neo pool deep blue tiles (Size- 24.7x 12.2 x 0.8cm) (square/rectangular) areaof approved colour as in floors/wall swimming pool area etc to match and including Providing and applying adhesive, ready to use grey cement based polymer modified tile adhesive for wall and floor tile fixing application in a minimum of 4 mm thickness. The tile adhesive must conform to C2TE according to EN 12004-2. The adhesive supplier must have their own manufacturing facility, should not be private label product or sourced from third party. The manufacturer must be an ISO 9001 & 18001 certified and valid certificates must be produced as proof complete all as specified and directed. |
| 21 | M&L for Maxgrip R10 endura vitrifed coloured tiles , size- 600x600x12mm thick square shape as in floors etc to match and including over Providing and applying approved adhesive, ready to use grey cement based polymer modified tile adhesive for wall and floor tile fixing application in a minimum of 4 mm thickness. The tile adhesive must conform to C2TE according to EN 12004-2. The adhesive supplier must have their own manufacturing facility, should not be private label product or sourced from third party. The manufacturer must be an ISO 9001 & 18001 certified and valid certificates must be produced as proof complete all as specified and directed. |
| 22 | M&L for non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tiles exc. 0.38 sqmbut n. exc 1.00 sqm of approved colour as in floors etc including with applying approved adhesive, ready to use grey cement based polymer modified tile adhesive for floor tile fixing application in a minimum of 4 mm thickness. The tile adhesive must conform to C2TE according to EN 12004-2. The adhesive supplier must have their own manufacturing facility, should not be private label product or sourced from third party. The manufacturer must be an ISO 9001 & 18001 certified and valid certificates must be produced as proof. |
| 23 | M&L for designer glazed ceramic tiles Coloured 600 x1200mm 7 to 8 mm thick in wall/dado etc, set & jointedin neat cement slurry & pointed in white or coloured cement to match renderingover 10 mm thick in CM 1:4 on stone masonry surfaces or surfaces other than fair face of brick work/ concrete surfaces including with applying suitable adhesive, ready to use grey cement based polymer modified tile adhesive for wall tile fixing application in a minimum of 4 mm thickness. The tile adhesive must conform to C2TE according to EN 12004-2. The adhesive supplier must have their own manufacturing facility, should not be private label product or sourced from third party. The manufacturer must be an ISO 9001 & 18001 certified and valid certificates must be produced as proof. |
| 24 | M&L for designer glazed ceramic tiles Coloured 450 x 300mm 7 to 8 mm thick in wall/dado etc, set & jointedin neat cement slurry & pointed in white or coloured cement to match renderingover 10 mm thick in CM 1:4 on stone masonry surfaces or surfaces other than fair face of brick work/ concrete surfaces including with applying approved adhesive, ready to use grey cement based polymer modified tile adhesive for wall and floor tile fixing application in a minimum of 4 mm thickness. The tile adhesive must conform to C2TE according to EN 12004-2. The adhesive supplier must have their own manufacturing facility, should not be private label product or sourced from third party. The manufacturer must be an ISO 9001 & 18001 certified and valid certificates must be produced as proof complete all as specified and directed. |
| 25 | M&L for finger grip with safety marking (size- 24.4cmx11.9cm) any colour and any pattern surrounding the edging of swimming poollaid over cement screed and jointed with over 10mm thick in cement mortar CM 1:3 complete all as specified and directed. |
| 26 | M&L for Machine cut kota stone slab flooring 14-16mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete lad over cement screed and jointed over screed bed or bedding layer of mortar 20mm thick in CM 1:6 for laying floor finish complete all as specified and directed. |
| 27 | M&L for kota stone slab 14-16mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with ditto as per item 47 over 10mm thick in cement mortar CM 1:3 complete all as specified and directed. |
| 28 | Demolition of cement concrete (unreinforced) in ground floors and pavings n.exc 15cm thickness (below or above ground level) complete all as specified and directed. |
| 29 | M&L for 100mm thick cement concrete type B-1, 1:2:4 (20mm graded aggregate) as base of flooring or similar article complete all as spd and directed |
| 30 | Material & Labour for providing and fixing stainless steel (Grade 304) Ladders made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement complete all as specified and directed. |
| 31 | S&F in repair Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty. |
| 32 | S&F in repair 45mm thick fiberglass type material of driving board size- (L- 2.40meters and width .50meters) with all fixtures and fittings complete all as specified and directed. |
| 33 | Taking downcement plaster ofany description from brick wall/ceilingsurfaces etc including racking out joints and hacking for key, scrubbing down with water etc complete all as directed. |
| 34 | M&L Rendering 15 mm thick cement plaster in CM 1:6 onfair faces of brick/concrete work surfaces finished even and smooth (without using extra lime or cement) complete all as specified and directed. |
| 35 | M&L Rendering 15 mm thick cement plaster in CM 1:4 onother than fair faces of brick/concrete surfaces finished and smooth without useing extra cement and using water proofing compound @ 3% by weight of cement contentcomplete all as specified and directed.Note :- WPC will measuered and paid separatly under relevant item of schedule. |
| 36 | M&L for rendering 5mm thick on fair faces of ceiling / chajja concrete surfaces in cement mortar 1:3finished even and smooth (without using extra lime or cement) complete all as specified and directed. |
| 37 | Material & Labour applying two coats of oil bound distemper paint on decorated or un- decorated plastered or unplastered surfaces of wall over a coat of wall primer after providing and applying plaster of paris putty of 1 mm thickness over plastered surface to prepare the surface even and smooth complete all as specified and directed. |
| 38 | Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces with 1mm thick wall care putty complete all as specified. |
| 39 | M&L for preparation of newly plastered surfaces of ceiling and applying two coats of distempering with 1st quality acrylic distemper (ready mixed)having VOC content less than 50 gms/litre, of approved manufacturer with 1 mm thick putty, of required shade and colour complete, as per manufacturer\"s specification complete all as specified and directed. |
| 40 | Material and labour for complete removal of existing treatment(any layers of existing treatment ) from walls/pillars/cornices by scraping down with using steel patti and mechanical sander machine (including provision of dust sucking) upto entire satisfaction of Engineer-in-charge, brooming and washing down with water including applying 1 mm thick wall care putty to make the surface even and smooth by using sander machine (with provision of dust sucking) as directed by Engineer-in-charge, after preparing the surfaces applying two coats of oil bound distemper , of approved manufacturer, of required shade and colour complete, as per manufacturer\"s specification complete all as specified and directed. |
| 41 | Material and labour for Preparation of old decorated surfaces (plastered/unplastered)of ceiling by removing / scraping down all loose particle, smoke soot, moulds, moss & efflorescent salts, oil & greasy spots etc with using broom / steel patti / wire brush / sand papering or by any other mean including applying 1mm thick wall care puttyfor filling to depressions/nail holes/light cracks etc and to make the surface even and smooth and also using sander machine (with provision of dust sucking) on uneven surface to make the surface even and smooth (before and after applying putty as per site situation) as directed by Engineer-in-charge and after preparing the surface smooth applying two coat of oil bound distemper on ceiling surfaces with paint brush complete all as specified and as directed |
| 42 | M&L for applying two coats of synthetic enamel paint over a coat of red oxide primer on newly steel surfaces of any description over 10cm in width or girth not otherwise described incl preparation of surfaces and as all specified |
| 43 | M&L, for preparation of old painted of steel surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint including steel staggings by using gun spraycomplete all as specified and directed. |
| 44 | Supply only Liquid water proofing compound |
| 45 | Removing all disintegrated and loose concrete of any thickness including plaster if any in RCC Column, Chajja, slab, beams, lintels etc, removing all loose rust/scale form exposed reinforcement bars by using wire brushes and sand paper including cleaning of exposed surfaces of reinforcement with protective anti corrosive epoxy bonding chemical (make : Pidilite) and tied reinforcement bars if reqd to reinforcement concrete bonding primer uniformly to exposed surfaces and applying cement mortar 1:3:1 with MPC (1 Part cement : 3 Part Sand : 1 Part 6mm coarse aggregate) to an average thickness not less than 20 mm and removing debris outside MD land all as specified and as directedNoted :- Reinforcement bars shall be measured and paid separately)” |
| 46 | Demolation of RCC of any description and in any position not otherwise specifically provided forincluding (renforcement cut as per required to facilitate demolition) |
| 47 | M&L for RCC (Nominal Mix) in type A1 1:1.5:3 (20mm graded aggregate) as in slab supported on wall, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like etc complete all as specified and directed. |
| 48 | M & L for Formwork to soffits of suspended slabs such as roof slabs, floorslabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) etc. for fair finished surfaces of concrete completeall as specified and directed. |
| 49 | M&L TMT mild steel bars 10mm dia and over,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with theincluding mild steel wire (annealed) not less than 0.9mmdia or securing with clips quality conforming to complete all as specified and directed. |
| 50 | Taking down chowkhat or frame with shutters n.exe 1.50 Sqm (without taking of shutter from frame ) each complete all as specified and directed. |
| 51 | Taking down chowkats or frames exc 1.5 sqm but n. exc 4 sqm each with shutters (without taking off shutters from the frame) complete all as specified and directed. |
| 52 | S&F for factory made single extruded WPC (Wood Polymer Composite) solid door/window/ceosetory windows and other frames/chowkhat of size 50x100 mm comprising of virgin PVC polymer of K value 58-60 (suspension grade ), calcium carbonate and natural fibers (wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms)fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS scews having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200N (face) and 1100N (Edge), minimum compressive strength of 58 N/mm2 and resistance to spread of flame of class A category with property of being termite /borer proof, water/moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in -Charge. (M.S. hold fast/lugs or SS dash fasteners shall be paid for separately) Note :- For WPC solid door/window frames, minus 5mm tolerance in dimension i.e depth and width of profile shall be acceptable. Variation in profile demension on plus sideshall be acceptable but no extra payment on this account shall be made. |
| 53 | S&F for factory made single extruded WPC (wood polymer composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers(wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum frame density of 650 kg/cum, screw withdrawal strength of 1800N (face) and 900N (Edge), minimum compressive strength of 50 N/mm2, modulus of elasticity 850N/mm2 and resistance to spread of flame of class A category with property of being termite /borer proof, water/moisture proof and fire retardant and fixing with stainless steelbutt hings of required size with necessary full body threaded star headed counter sunk S.S screws , all as per direction of Engineer-in -Charge. Note :- Stainless steel butt hinges and necessary SS Screws shall be paid separately) |
| 54 | Supply and fixing factory made uPVC white colour Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire meshpanels) upto 1.50m height made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm) comprising of uPVC multichambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware\"s and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. (Glass or wiremesh shall be paid separately). Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. |
| 55 | Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge. |
| 56 | Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, locking arrangement ,C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-Charge. |
| 57 | S&Fin repair anodised aluminium grill (anodised transparent or dyed to required shade according to IS:1868 with minimum anodic coating of grade AC 15) of approved design/pattern , with approved standard section and fixed to the existing window frame with C.P brass/stainless steel screws @ 200mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, complete all as specified and directed. |
| 58 | S&F for framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 , the grill shall be inserted in the wall surface including necessary drilling and grouting with cement etc complete all as specified and directed. |
| 59 | S&F Sheet glass 5.5 mm thick , ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified and directed. |
| 60 | S & F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples. |
| 61 | M&L 6mm thick ACP board (Aluminium composite panel), exterior grade, (approved colour) fixed with GI/aluminium tapperd clip to aluminium frame work all as specified and as directed. |
| 62 | S&F for single piece fancy type designed bevelled edge mirror of selected quality glass, mounted on 6 Nos stainless steel and fixed to wall with chromium plated brass screws and cup complete all as specified and directed. |
| 63 | S&F in repair Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty. |
| 64 | Supply & fixing in repair of wall mounted corner tempered glass shelf with guard rail rectangle stand storage shelf (size- 25 cm) complete all as specified and directed. |
| 65 | S&F in repair aluminium (extruded section body) door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and directed. |
| 66 | M & L for aluminium snake guard fixed in aluminium doors any size complete all as spd and directed |
| 67 | Dismantling wall and ceiling board of any descrition complete all as specified and directed. |
| 68 | S & F powder coatedaluminium snap grid frame work for false ceiling all as specified. |
| 69 | S&F for Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting levelfixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified |
| 70 | S&F for 6mm thick non asbestos fibre cement designer building boards fixed or laid on aluminium frame/grid with screws , complete all as specified and directed. |
| 71 | Dismantling wooden boarding, any description, fixed in any position with nails complete all as specified and directed. . |
| 72 | S&F for 18/19 mm thick prelaminated PVC plain solid plyfor shelf fixed with screws to PVC frame work etc complete all as specified and directed. |
| 73 | S & F for 18/19 mm thick prelaminated PVC solid board, exterior grade, prelaminated one side with decorative choice lamination & otherside balancing white lamination for shutter, fixed with PVC frame work including Stainless steel piano/dadu hinges complete all as specified and directed. |
| 74 | S&F for magnetic door catch drawer magnet including all necessary fittings complete all as spd and directed |
| 75 | Taking down the aluminium shutter/window with frame and refixing in some position exc 1 sqm but n.exc 2 sq in length complete all as specified and directed. |
| 76 | S&F 100mm longbutt hinges, extruded alluminium alloy/stain less steel with galvanised mild steel hinge pin, anodised and fixed , type B-21 complete all as specified and directed. |
| 77 | S&F 75mm longbutt hinges, extruded alluminium alloy/stain less steel with galvanised mild steel hinge pin, anodised and fixed , type C-21 complete all as specified and directed. |
| 78 | S&F stainless steel150 mm barrel tower bolts of extruded section complete all as specified and directed. |
| 79 | S&F stainless steel 100mm barrel tower bolts of extruded section complete all as specified and directed. |
| 80 | S&F stainless steel 150 mm longhandles,fabricated type, complete all as specified and directed. |
| 81 | S&F stainless steel 100 mm long handles,fabricated type, complete all as specified and directed. |
| 82 | S&F stainless steel 300 mm longsliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections and fixed complete all as specified and dirceted. |
| 83 | S&F for 150mm long floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed. |
| 84 | S&F in repair stainless steelfancy curtain rod with conical end balls suitable for fixing as end of curtain/dropery rods complete all as spd and directed |
| 85 | M&L for 18mm to 20mm thick green marble (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in 15mm thick cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including 20mm thick screed bed CM(1:6) complete all as spd and directed |
| 86 | S&F in repair Steel rolling shutters, 1.25mm thickness of laths, with out ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, complete:gear operated type with bevel gear box and crank handle complete all as specified and directed. |
| 87 | Supply only Safety lever locks mild steel with 4 levers for rolling shutters complete all as specified and directed. |
| 88 | Supply only ball bearing for rolling shutters complete all as spd and directed |
| 89 | S&F in repairs closet Vitreous china squatting pan Orissa pattern of size 580x440mm white with integral foot rests (excluding flusing cistern and flush pipe) including connection to trap and to flushing pipe, antisyphonage connection pipe etc complete making good disturb surface with existing finish of floor complete all as specified and directed. |
| 90 | S&F in repairs vitreous china wash down water closet pan, pedestal pattern Pedestal pan and trap(excluding flushing cistern and flush pipe),connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe, etc and including plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel CP or aluminised hinging device all as specified and directed. |
| 91 | S&F in repairs single-piece, ceramic vitreous china water closetwith P or S- trap (pedestal pattern) complete connecting to flush pipe, including PP soft-close seat cover dual flushing, anti-germ glaze with flat bottom and mild steel chromium plated or aluminium hinging device (including flushing cistern and flushing pipe) complete all as specified and directed. |
| 92 | S&F in reapir wall-mounted, chrome-finish brass health faucet kit with 1-meter flexible hose and 15mm diameter hose complete all as specified and directed. |
| 93 | S&F fancy type wall-mounted toilet roll paper holder with flap,crafted from brass chromium plated including screw and chromiun plate brass cleats complete all as specified and directed. |
| 94 | S&F in repairs 10 litre capacity PVC low level flushing cisternwith all accessories complete fixed with WC including syphone pipe, PVC flushing pipe of size complete (with brackets) flush pipe of plyethene of low or high density of PVC 32mm dia for low level cistern all as specified and directed. |
| 95 | S&F in repair wall-hung white ceramic Vitreous China urinal with a top inlet, half stall bowl type with sensor kit including all fittings and fixtures complete all as specified and directed. |
| 96 | S&F 8MM rectangular shaped urinal partition with frosted glasssize 450 mm x 900 mm terminating about 40 cm above floor level and fixed with stainless steel clamp on wall complete all as specified and directed. |
| 97 | S&F vitreous china counter top wash hand basin (self rimming) leed (Size 600 x 400 x 185mm) colour brilliant / off white including fixing brackets and prepolished granite slab of size 1000 x 600mm size and cutting notch of required size as per the wash hand basin to be fixed in it complete all as specified and directed. |
| 98 | S&F basin mixer without pop up chromium plated complete all as specified and directed. |
| 99 | S&F for CP bottle trap(with internal partition) 32mm size with 250mm & 190mm complete all as specified and directed. |
| 100 | S&F brass CP Tubular towel rail 20mm dia, D type, 60 cm long between flanges complete all as specified and directed. |
| 101 | Taking down steel tubing having bore of pipe 15 mm and connections, including cleaning for refixing or removal to store complete all as specified and directed |
| 102 | Taking down steel tubing having bore of pipe 20 mm and connections, including cleaning for refixing or removal to store complete all as specified and directed. |
| 103 | Cutting chases, pinning in making good to facing on brick walls where required and pointing in cement mortar (1:3) to ends for concealed water tubing and making good, cutting n. exc. 10cm girth complete all as specified and directed. |
| 104 | S&F for 20 mm outer diaCPVC, SDR 11 & plain CPVC SDR 11plain/brass treaded fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and directed. |
| 105 | Ditto all as per Item No above but25 mm outer dia complete all as specified and directed. |
| 106 | Supplyand fix in repair bib taps of 15mm bore fancy type, chromium platedcast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for brass ferrule complete all as specified and directed. |
| 107 | S&F in repair 15mm bore fancy type stop valve , chromium platedwith long shank and cup (concealed type)cast copper alloy, screwed down , high pressure , with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed |
| 108 | S&F in repair 15mm bore fancy type stop valve/angle valve , chromium platedcast copper alloy, screwed down , high pressure , with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed. |
| 109 | S&F in repair 15mm bore chromium plated cast copper alloy2-IN-1 bib cock tap , screwed down for iron pipe or for brass ferrule and fixed complete all as specified and directed. |
| 110 | S&F 15mm bore angle cock chromium plated concealed with long shank type screwed down, high pressure complete all as specifiedanddirected. |
| 111 | Supply and fix in repair for Gun metal gate valve,15 mm bore, cast copper alloy screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and directed. |
| 112 | Demolition of brick work built in cement mortar or cement lime mortar incl all quoins, arches pillars etc and removing unserviceable material exc 100 mtr complete all as specified and directed |
| 113 | M&L for old size brick work with fly ash bricks straight or curved on plan exc 6 m mean radius build in CM 1:6 complete all as specified and directed. |
| 114 | M&L brick work with half bricks thick fly ash bricks straight or curved on plan exc 6 m mean radius build in CM 1:4 complete all as specified and directed. |
| 115 | S & F in repair PVC (SWR) pipes of 110 mm dia single socketed in any length with rubber ring joints fixed to walls, including with clamps etc complete all as spd and directed |
| 116 | -ditto- all as per item here in before But 75mm bore complete complete all as specified and directed. |
| 117 | S & F for PVC (SWR) pipes of 75 mm dia single socketed in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed. |
| 118 | S & F in repair PVC (SWR) bends any radius of 110 mm bore with access door complete all as spd and directed |
| 119 | -ditto- all as per item No here in before But 75mm bore complete all as spd and directed |
| 120 | S & F PVC (SWR) reducers of 110 mm bore complete all as specified and directed. |
| 121 | S&F 75mm PVC (SWR) vent cowl complete all as specified and directed. |
| 122 | S&F 110mm PVC (SWR) junction single (single T) equal or unequal complete all as specified . |
| 123 | S&F 75mm PVC (SWR) junction single (single T) equal or unequal complete all as specified . |
| 124 | S&F PVC SWR pipes 150 mm bore single socketed in any length with rubber ring joint fixed to wallwith PVC clamps for rain water pipes including taking down old pipes complete all as specified and directed and directed . Make : Supreme/ Finolex. |
| 125 | S&F PVC SWR bends of 150 mm bore complete all as specified and directed. |
| 126 | S&F as in repair grating square 150mm size of PTMT(minimum 100 gms) complete all as specified and directed. |
| 127 | S&F as in repair grating square with waste hole 150mm size of PTMT(minimum 100 gms) complete all as specified and directed. |
| 128 | M&L 75mm thick PCC 1:3:6 type C2 (using 40mm graded stone aggregate) fininshed the as in plinth protection surfaces even and smooth without using extra cement complete all as specified and directed. |
| 129 | M&L Forming Contraction (Dummy) joints 30mm deep x 10mm wide, filled with sealing compound grade Acomplete all as specified and directed. |
| 130 | M&L Cement concrete 1:3:6, type C-1(using 20mm graded stone aggregate) in surface channels ,drains, RWP\"s PCC shoes and Manholes complete all as specified and directed. |
| 131 | Taking down carefully aluminium/copper point wiring (light, fan, socket or power) complete, including fixtures and fittings such asswitches, ceiling roses, pendent, regulators, sockets, bell push, bell, light fittingsetc. removing serviceable materials to store for keeping in safe custody for reuse at site or for taking credit (Credit shall be made as per Schedule of credit), removing rubbish from the site and making good all disturbed surfaces of walls, floors etc. to match to the existing surfaces complete all asspecified anddirected. |
| 132 | Material and labour for (concelaed Type) point wiring confirming to IS-694,1100 Volts grade ISI Marked including necessary chase cutting of wall for one light/fan/call bell point with 1.5 sqmmPVC insulated (FR-LSH) unsheathed copper cable multistranded conductor 1100 volts gradecontrolled by one way switchincluding 1.5 sqmm PVC (FR-LSH) insulated unsheathed copper cable multistrand conductor 1100 volts grade for continuity earth wire connected to common earth dolly drawn through and including PVC conduit (medium grade) with all accessoriesand sunk modular GI box(1.20mm thick) for mounting of fittings like switch, socket and fan regulator with modular inner plate and cover plate and making good the distrubed surfaces as per the existing complete all as specified and as directed . Note: A. Red coloured cable shall be used for live connection,black coloured cable shall be used for neutral connection and greencoloured cable shall be used for earthing. Separate cable for earthing and neutral to be used for each individual circuit from the distribution board.B. The Rate of point wiring includes the following :-(i)Copper wire(ii)PVC Conduit with accessoreis(iii) Chase cutting(iv) other accessories such as modular GI box, modular inner plate and modular Cover plate etc. |
| 133 | .-Ditto- all as per item No 131.00 here-in-before butfor 3 pin 6 amps switch socket combination on the same board with 1.5 Sqmm cable and -ditto-. |
| 134 | .-Ditto- all as per item No 131.00 here-in-before butfor 3 pin 6 amps switch socket combination on the independant boardwith 1.5 Sqmm cable and -ditto-. |
| 135 | .-Ditto- all as per item No 131.00 here-in-before butfor one light point control by 2 way switch with 1.5 Sqmm cable and -ditto-. |
| 136 | Material and labour for (concelaed Type) point wiring confirming to IS-694,1100 Volts grade ISI Marked including necessary chase cutting of wall for one 16Amp socket outlet on independent board point with 4.0 sqmmPVC insulated (FR-LSH) unsheathed copper cable multistranded conductor 1100 volts gradecontrolled by one way switchincluding 4.0 sqmm PVC (FR-LSH) insulated unsheathed copper cable multistrand conductor 1100 volts grade for continuity earth wire connected to common earth dolly drawn through and including PVC conduit (medium grade) with all accessoriesand sunk modular GI box(1.20mm thick) for mounting of fittings like switch, socket and fan regulator with modular inner plate and cover plate and making good the distrubed surfaces as per the existing complete all as specified and as directed by the Engr-in-Charge. Note: A. Red coloured cable shall be used for live connection,black coloured cable shall be used for neutral connection and greencoloured cable shall be used for earthing. Separate cable for earthing and neutral to be used for each individual circuit from the distribution board.B. The Rate of point wiring includes the following :-(i)Copper wire(ii)PVC Conduit with accessoreis(iii) Chase cutting(iv) other accessories such as modular GI box, modular inner plate and modular Cover plate etc. |
| 137 | Supply and fixing switch piano, flush type 5/6 Amps 240 Volt single pole, one way complete all as specified and as directed. |
| 138 | Supply and fixing bell flush type single pole 6 amps 240 volts AC with polycarbonate bodycomplete all as specified and as directed. |
| 139 | Supply and fixing switch piano, flush type 15/16 Amps 240 Volt two way complete all as specified and as directed. |
| 140 | Supply and fixing socket outlet 2 in 1, 5 pin 5 Amp,230 Voltsflush type complete all as specified and as directed. |
| 141 | Supply and fixing switch socket combination 2 in 1, 5 pin 5 Amps, 240 VFlush type, complete all as specified and as directed. |
| 142 | Supply and fixing switch socket combination 3pin, 16 Amps, 240 Volts, flushtype universal complete all as specified and as directed. |
| 143 | Supply and fixing Calling Bell multi music type, complete all as specified and as directed. |
| 144 | Supply and fixing ceiling rose surface bakelite three terminal65 x 50mm, PVC/Polycarbonate, isolated body 240 volts complete all as specified and as directed. |
| 145 | Supply and fixingfan regulator electronic, flush type humming with (step type) polycarbonate body suitable to control speed of fan from 0 to 100% and connecting electrically complete all as specified and as directed |
| 146 | Supply and fixing lamp holder suitable for batten fittings complete all as specified and as directed. |
| 147 | Supply and fixingas in replacement Single pole and neutral sheet metal enclosure (IP 42 protection) with a two pin and earth plug and socket complete with one single pole MCB 20 Amps complete all as specified and as directed. |
| 148 | Supply and fixing sub-main wiring with PVC insulated & unsheathed two run of 6 Sqmm single core multi stranded copper conductor cable (FRLSH), 1100 Volt grade alongwith one run of6 Sqmm PVC insulated & unsheathed copper conductor cable (FRLSH), 1100 Volt grade, connected to common earth dolly asearth continuity conductor, drawn through 20mm bore PVC concealed conduit (medium grade) after and including taking down existing sub main wiring complete all as specified and as directed.Note : Two runs of 6 Sqmm, one run of 6 Sqmm cable and one run of conduit shall be measured as one unit. |
| 149 | Supply and fixing LED street light fitting 35Watt, 230V, AC outdoor type withhigh pressure diecast aluminium hoising and heat resistance complete with driver, lamp bracketwith impact and corrosion resistant includingthermal management in multiple optics complete with IP65/66 protection complete all as specified and as directed. |
| 150 | Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220V AC decorative type with driver, holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed. |
| 151 | Supply and fixing as in replacement for LED tube light fitting 1 X 20Watt, 230V, 1200mm, 6500Kwith aluminium housing & integrated electronic driver fixingon PVC/wooden round block including all accessories and connecting to celling rose complete all as specified and as directed. |
| 152 | Supply and fixingas in replacement for 2\" x 2\" surface mounting LEDluminarie 40 W after mounting white powder coated CRCA housing with high power LED\"s, plane front frame with translucent cover fixed to the housing including LED lamp, other accessories and necessary electric connection complete all as specified andas directed. |
| 153 | Supply and fixingexhaust fan,steel bodyAC single Phase 230V of size 300m sweep with, blades, and frame and louvers complete all as specified andas directed. |
| 154 | Supply and fixed epoxy powder coated sheet metal enclosure for DBs double door (when MCBs to be used), single pole and neutral 240V, 12 ways with mounting fitted with bus bar, DIN channel, neutral link and incoming contract complete all as specified and as directed. Note :cable fixed with suitable size Lux and blanker fill with blanker. |
| 155 | Supply and fixed epoxy powder coated sheet metal enclosure for DBs double door (when MCBs to be used), single pole and neutral 240V, 8 ways with mounting fitted with bus bar, DIN channel, neutral link and incoming contract complete all as specified and as directed. Note :cable fixed with suitable size Lux and blanker fill with blanker. |
| 156 | Supply and fixed epoxy powder coated sheet metal enclosure for DBs double door (when MCBs to be used), single pole and neutral 240V, 4 ways with mounting fitted with bus bar, DIN channel, neutral link and incoming contract complete all as specified and as directed. Note :cable fixed with suitable size Lux and blanker fill with blanker. |
| 157 | Supply and fixing 240V, 10 KA \"B\" curve miniature circuit breaker (MCB) of single poles and current carrying capacity 5 to 32 Amps, in the MCB DB complete with connection testing and commissioning complete all as specified and as directed. |
| 158 | Supply and fixing MCB 32 Amps, SPN, 240 Volt \"C\" series, breaking capacity 10 KA complete all as specified and as directed. |
| 159 | Supply and fixing MCCB 63 Amps, four pole, 3 phase, 415 Volt capacity, breaking capacity 16 KA complete with proper coppe thimble, copper reducer etc complete all as specified and as directed. |
| 160 | Supply and fixing LED Bollard light disc of 15W 3000K unique tringular design with IP65 protection, resistance to impact and corrsion. Glare free and better uniformity complete with all acessories complete all as specified and as directed. |
| 161 | Supply and fixing LED post top 40W with IP65 rated, high pressure die cast aluminium housing, lens and toughened glass cover outdoor luminare, complete connection with twin core copper conductor with all acessories complete all as specified and as directed. |
| 162 | Supply and fixing LED flood light 200W with IP65 protection, high pressure die cast aluminium housing,lens and toughened glass cover outdoor luminaire, complete connection with twin core copper conductor with all acessories complete all as specified and as directed. |
| 163 | Supply and fixing ceiling fan of capacity 1200mm, 240 Volts, ISI mark,BEE rated 5 star,Brushless direct current (BLDC) without remote complete with down rod, blade and connecting with flexible copper conductor incuding taking down old one and removing to MES store complete all as specified and as directed. |
| 164 | Materials and labour for earthing complete with galvanised iron earth plate electrode 600 mm x 600 mm x 6 mm thick, burried directly and preferably vertically in ground, earth pit not less than 2.25 Mtr deep below ground level with top edge of the plate not less than 1.5 m below ground level connetced with galvanised wire of 4mm diaby means of nuts, bolts, check nuts and washers made of galvanised iron or steel earthing lead to be protected by galvanised iron pipe of 15mm bore (light grade) and other end connected to earthing test point or lightening arrestor or main controlling switch as directed including providing funnel with 20mm bore galvanised iron pipe (medium grade), wire mesh, charcoal or coke and common salt in alternate layer of 15cm (compacted thickness) all round the earth electrode, concrete earth pit in PCC (1:3:6) type C-1 (with 20mm graded aggregate), 50mm thick precast RCC (1:2:4) cover slab (re-inforced with 8mm dia TMT bar @ 15 cm C/C bothways and suitable handle made of 10mm dia) including necessary earth work in excavation, returning filling and removal of surplus earth upto a distance not exceeding 50 m etc all as shown on electrical plate No. 3 of MES Schedule Part-I(2009) complete including testing on completion and taking down old unserviceable materials complete all as specified and as directed. |
| 165 | Dismantling old unserviceable cable any type any size complete all as specified and directed. |
| 166 | Supply and laying under ground XLPE insulated PVC sheathed (Heavy duty) armoured 1100 volts grade aluminium conductor cable of size 16 Sqmm 4 core laid in trenches/ fixed to wall as per IS 7098 (Part I) including connection cable glands, aluminium lugs etc complete all as specified and as directed. |
| 167 | Excavation in trenches not exceeding 1.5 wide and n exc 1.5 in depth and getting out in soft/loose soil complete all as specified and as directed. |
| 168 | Returning, filling,including spreading, levelling, watering and well raming in layer not execeeding 25 cm in soft/loose soil complete all as specified and as directed. |
| 169 | Removal of excavated soil to a distance not execeeding 50 meter and depositing where directed at a level not exceeding 1.5 meter above the starting point in soft/loose soil complete all as specified and as directed. |
| 170 | Supply and lay for dry river sand filling for cable protection with a layer of 8 cm deep before layinglayingand 15 cm covering above top edge of cable after laying complete all as specified and as directed. (Note : Punned thichkness shall be measured) |
| 171 | Supply and lay sub class B fly ash bricks locally available the best quality of size 25x12.5x7.5 cm laid drywidth wise across the line of cable in strenches complete all as specified and as directed. (Note : Punned thichkness shall be measured) |
| 172 | Supply and Fixing 40mm dia light grade GI pipe for road cross/cutting on wall floor drain etc. complete all as specified and as directed.Note : |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
| 4 | Click here to download tender document | Tender Documents |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2026 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
