|
| 1 | Supply, installation, connecting, testing and commissioning of horizontal end suction centrifugal pump set suitable for delivering 2850 LPM at 90 m total head, complete with CI casing, bronze impeller, stainless steel shaft with renewable shaft sleeve, gland packing type sealing arrangement with lantern ring, and renewable wearing rings, designed for continuous operation; complete with suitably rated AC 3-phase, 415 V ±10%, 50 Hz TEFC copper wound squirrel-cage induction motor, IE2 efficiency, NFLP, IP55 protection, Class ‘F’ insulation, mounted on MS fabricated common base frame; direct-coupled through flexible Lovejoy/Fenner type coupling with coupling guard; including foundation bolts, base plate, alignment, grouting, pressure gauge, vacuum gauge, all standard fittings and accessories, and all materials, labour and incidental works required to complete the pump set in all respects in accordance with relevant IS/BS standards for firefighting application including painting with PO red colour and to the satisfaction of the Engineer-in-Charge. Note: PCC/RCC foundation shall be measured and paid separately under relevant BOQ items; however, the cost of the MS fabricated common base plate, foundation bolts, nuts and all required accessories as per manufacturer’s recommendations shall deemed to be included in the quoted rate. |
| 2 | Supply, installation, connecting, testing and commissioning of horizontal end suction centrifugal pump set suitable for delivering 2850 LPM at 90 m total head, complete with CI casing, bronze impeller, stainless steel shaft with renewable shaft sleeve, gland packing type sealing arrangement with lantern ring, and renewable wearing rings, designed for continuous operation, complete with suitably rated diesel engine (water-cooled) with electric start/manual start system, fuel tank of capacity 100 Liters, suitable rated battery with leads, exhaust system with silencer, control panel and all engine-mounted accessories, mounted on MS fabricated common base frame; direct-coupled through flexible Lovejoy/Fenner type coupling with coupling guard; including foundation bolts, base plate, alignment, grouting, pressure gauge, vacuum gauge, all standard fittings and accessories, and all materials, labour and incidental works required to complete the pump set in all respects in accordance with relevant IS/BS standards for firefighting application including painting with PO red colour and to the satisfaction of the Engineer-in-Charge. Note: PCC/RCC foundation shall be measured and paid separately under relevant BOQ items; however, the cost of the MS fabricated common base plate, foundation bolts, nuts and all required accessories as per manufacturer’s recommendations and extension of exhaust pipe to outside of the building with suitable pipe and wrapping the asbestos rope shall deemed to be included in the quoted rate. |
| 3 | Supply, installation, connecting, testing and commissioning of horizontal end suction centrifugal pump set suitable for delivering 480 LPM at 90 m total head for Jockey pump, complete with CI casing, bronze impeller, stainless steel shaft with renewable shaft sleeve, gland packing type sealing arrangement with lantern ring, and renewable wearing rings, designed for continuous operation; complete with suitably rated AC 3-phase, 415 V ±10%, 50 Hz TEFC squirrel-cage induction motor, IE2 efficiency, NFLP, IP55 protection, Class ‘F’ insulation, mounted on MS fabricated common base frame; direct-coupled through flexible Lovejoy/Fenner type coupling with coupling guard; including foundation bolts, base plate, alignment, grouting, pressure gauge, vacuum gauge, all standard fittings and accessories, and all materials, labour and incidental works required to complete the pump set in all respects in accordance with relevant IS/BS standards for firefighting application including painting with PO red colour and to the satisfaction of the Engineer-in-Charge. Note: PCC/RCC foundation shall be measured and paid separately under relevant BOQ items; however, the cost of the MS fabricated common base plate, foundation bolts, nuts and all required accessories as per manufacturer’s recommendations shall deemed to be included in the quoted rate. |
| 4 | Supply, installation, connecting, testing and commissioning of horizontal split casing, single-stage centrifugal pump set suitable for delivering 290 m³/hr at 50 m total head and 1480 RPM, complete with CI casing, bronze impeller, stainless steel shaft with renewable shaft sleeve, gland packing type sealing arrangement with lantern ring, and renewable wearing rings, designed for continuous operation; complete with suitably rated AC 3-phase, 415 V ±10%, 50 Hz TEFC squirrel-cage induction motor 1480 RPM, IE2 efficiency, NFLP, IP55 protection, Class ‘F’ insulation, mounted on MS fabricated common base frame; direct-coupled through flexible Lovejoy/Fenner type coupling with coupling guard; including foundation bolts, base plate, alignment, grouting, pressure gauge, vacuum gauge, all standard fittings and accessories, and all materials, labour and incidental works required to complete the pump set in all respects in accordance with relevant IS/BS standards for fresh water application including painting with approved colour shade and to the satisfaction of the Engineer-in-Charge. Note: PCC/RCC foundation shall be measured and paid separately under relevant BOQ items; however, the cost of the MS fabricated common base plate, foundation bolts, nuts and all required accessories as per manufacturer’s recommendations shall deemed to be included in the quoted rate. |
| 5 | Note for item No. 1.00 to 4.00 : Make and specification of pump sets, motors and Diesel Engine complete with accessories shall be submitted in duplicate for approval of GE through Engineer-in-Charge before placing order for procurement. |
| 6 | Design, fabricate, supply, installation, testing and commissioning of Automatic Fire Fighting Pump Set Control Panel, Indoor Type cubicle panel board compartmentalized suitable for 3 phase 4 wire, 415 Volts, 50 Hz, AC supply system, factory fabricated in an approved factory having modern fabrication facilities, made out of CRCA sheet steel of 2mm thick with front and rear openable doors with locking facility. Complete panel board shall be applied with powder coat painting of PO red shade duly pretreated with seven tank process and suitable packing material for IP-43 degree of protection and including provision of 50 mm x 50 mm x 6 mm angle iron base frame of suitable size for floor mounting the panel board with a minimum ground clearance of 300 mm above FFL to the bottom of panel including PCC foundation with PCC 1:3:6, type C1 using 20mm graded stone aggregate. Detachable gland plates including double compression stainless steel cable glands of suitable size shall be provided for all incoming and outgoing cables. Steel plate Danger Notice Boards (02 Nos) LT 415/440 Volts, and manufacturer\"s name plate shall be riveted on panel board. The size of panel board shall be suitable for accommodating and including provision of following switchgear, control gear and accessories including internal wiring with suitable gauge of copper cables complete all as specified and directed:- |
| 7 | (Item No 6.00 Contd--)(i) Bus bar:- TPN Copper bus bar of suitable rating provided with heat shrinkable coloured PVC sleeve insulation mounted on insulators for main bus bar, copper busbar links from main bus to outgoing MCCBs, Star Delta starters and cable terminals. Continuous earth bus with GI strip of suitable size capable for carrying full short circuit current for 1 sec shall be provided at bottom of the panel.(ii) Incomer:- (a) MCCB, 400 A, 4 Pole, 50 KA (Ics=100%Icu), 415 V, 50 Hz, with adjustable thermal - magnetic release with spreader links and extended ROM - 01 No(b) Digital Voltmeter with selector switch - 01 Set.(c) Digital Ammeter with selector switch & suitable ratio of CT\"s - 01 set(d) LED Pilot light indication lamps for R,Y,B phases - 01 Set of 03(iii) Outgoing (for Main Pump):- (a) MCCB, 250 A, 3 Pole, 50 KA (Ics=100%Icu), 415 V, 50 Hz, with adjustable thermal - magnetic release with spreader links and extended ROM - 01 No (for main pump)(b)Fully Automatic Star Delta (FASD) starter suitable for 75KW / 100 HP, 3 phase, 415 V, 50 Hz, AC induction motor coupled with centrifugal pump with Overload Load Relay, Single Phasing Preventor, Start / Stop Push Buttons, LED Indications for Running/Starting-Stopping etc complete with auto / manual selector for pressure switch- 01 Set(c)Digital Ammeter with Selector Switch and suitable ratio of CTs - 01 Set |
| 8 | (Item No 6.00 Contd--)(iv) Outgoing (for Jockey Pump):- (a) MCCB, 100 A, 3 Pole, 25 KA (Ics=100%Icu), 415 V, 50 Hz, with adjustable thermal - magnetic release with spreader links and extended ROM - 01 No (for jockey pump)(b)Fully Automatic Star Delta (FASD) starter suitable for 18.5 KW / 25 HP, 3 phase, 415 V, 50 Hz, AC induction motor coupled with centrifugal pump with Overload Load Relay, Single Phasing Preventor, Start / Stop Push Buttons, LED Indications for Running/Starting-Stopping etc complete with auto / manual selector for pressure switch - 01 Set(c)Digital Ammeter with Selector Switch and suitable ratio of CTs - 01 Set(v) Diesel Engine Controller:- (a) 100BHP Diesel Engine auto start controls with DC Voltmeter,Ammeter, hooter, indication lamp etc. with Battery charger-01No |
| 9 | Design, fabricate, supply, installation, testing and commissioning of Indoor Type cubicle panel board compartmentalized suitable for 3 phase 4 wire, 415 Volts, 50 Hz, AC supply system, factory fabricated in an approved factory having modern fabrication facilities, made out of CRCA sheet steel of 2mm thick with front and rear openable doors with locking facility. Complete panel board shall be applied with powder coat painting of approved shade duly pretreated with seven tank process and suitable packing material for IP-43 degree of protection and including provision of 50 mm x 50 mm x 6 mm angle iron base frame of suitable size for floor mounting the panel board with a minimum ground clearance of 300 mm above FFL to the bottom of panel including PCC foundation with PCC 1:3:6, type C1 using 20mm graded stone aggregate. Detachable gland plates including double compression stainless steel cable glands of suitable size shall be provided for all incoming and outgoing cables. Steel plate Danger Notice Boards (02 Nos) LT 415/440 Volts, and manufacturer\"s name plate shall be riveted on panel board. The size of panel board shall be suitable for accommodating and including provision of following switchgear, control gear and accessories including internal wiring with suitable gauge of copper cables complete all as specified and directed:- |
| 10 | (Item No 7.00 Contd--)(i) Bus bar:- TPN Copper bus bar of suitable rating provided with heat shrinkable coloured PVC sleeve insulation mounted on insulators for main bus bar, copper busbar links from main bus to outgoing MCCBs, Soft Starters and cable terminals. Continuous earth bus with GI strip of suitable size capable for carrying full short circuit current for 1 sec shall be provided at bottom of the panel.(ii) Incomer:- (a) MCCB, 250 A, 4 Pole, 50 KA (Ics=100%Icu), 415 V, 50 Hz, with adjustable thermal - magnetic release with spreader links and extended ROM - 01 No(b) Digital Voltmeter with selector switch - 01 Set.(c) Digital Ammeter with selector switch & suitable ratio of CT\"s - 01 set(d) LED Pilot light indication lamps for R,Y,B phases - 01 Set of 03(iii) Outgoing:- (a) MCCB, 200 A, 3 Pole, 50 KA (Ics=100%Icu), 415 V, 50 Hz, with adjustable thermal - magnetic release with spreader links and extended ROM - 03 Nos (02 working + 01 standby)(b) HRC Fuse base of 200 A with fuses for R,Y,B phases - 03 Sets(c) Soft Starter for soft starting and stopping of 55KW / 75 HP, 3 phase, 415 V, 50 Hz, AC induction motor coupled with centrifugal pump with provision of bilt-in bypass contactor, essential motor protections against instantaneous over current, bypass overload, motor overload, phase imbalance, phase loss, phase sequence, excess start time, motor thermostat, supply fault, shorted SCR and LED indications for Ready / Tripped, Running/Starting-Stopping, Fault Code etc - 03 Nos (02 working + 01 standby)(d)MCB 4P, 40 Amps, 10 KA, \"C\" curve - 04 Nos.(e)MCB 2P, 32 Amps, 10 KA, \"C\" curve - 04 Nos. |
| 11 | Design, fabricate, supply, installation, testing and commissioning of outdoor type cubicle panel board with inside panel suitable for 3 phase 4 wire, 415 Volts, 50 Hz, AC supply system, factory fabricated in an approved factory having modern fabrication facilities, made out of CRCA sheet steel of 3mm thick for outer shell and 2mm thick for inner shell with front openable door with two point locking arrangement i.e. Key locking system & pad-locking. Complete panel board shall be applied with powder coat painting of approved shade duly pretreated with seven tank process and suitable packing material for IP-54 degree of protection and including provision of 50 mm x 50 mm x 6 mm angle iron base frame of suitable size for mounting the panel board with a minimum ground clearance of 900 mm above GL to the bottom of panel including PCC foundation with PCC 1:3:6, type C1 using 20mm graded stone aggregate. Detachable gland plates including double compression stainless steel cable glands of suitable size shall be provided for all incoming and outgoing cables. Steel plate Danger Notice Board(01 No) LT 415/440 Volts, and manufacturer\"s name plate shall be riveted on external doors of feeder pillar box. The size of panel board shall suitable for accommodating and including provision of following switchgear, control gear and accessories including internal wiring with suitable gauge of copper cables complete:- (a) MCB, 40 A, 4 Pole, 10 KA, 415 V, 50 Hz- 01 No (incomer)(b) Digital Voltmeter with selector switch - 01 No(c) Digital Ammeter with selector switch - 01 No(d) LED Pilot light indication lamps for R,Y,B phases - 01 Set of 03(e) Three Phase Submersible Pump Controllers with Single Phase Preventer,DOL starter (with wideband coil) coil voltage 360V-W (200V-400V), relay range 6-10A suitable for 5 HP submersible pump motor - 01 No. |
| 12 | Note for item No. 6.00 to 8.00: The Contractor shall submit set of all drawings of the L.T. Panels / Pillar Boxes and its components in duplicate and get the same approved from GE before commencement of production. The contractor shall furnish all details and clarifications required if any for scrutiny and evaluation. Manufacture of material to be supplied shall be done strictly as per approved drawing. However, approval of drawing shall not absolve the contractor/supplier of his liability for ensuring correctness according to applicable standards & regulations. |
| 13 | Supply, laying and connecting of PVC insulated and PVC Round Sheathed, Multicore Annealed Bare Copper Conductor (flexible) industrial cable of size 50 sqmm, 3 core for Voltage Grade 1100 Volts, Conforming to IS 694:2010 complete laid in duct / cable tray / drawn through pipes etc including provision of lugs, glands, nuts, bolts & washers etc for connecting in LT panel/ motor terminal plate and testing on completion all as specified and directed. |
| 14 | Supply, laying, connecting, testing & commissioning of PVC insulated and PVC Round Sheathed, Multicore Annealed Bare Copper Conductor (flexible) industrial cable of size 10 sqmm, 3 core for Voltage Grade 1100 Volts, Conforming to IS 694:2010 complete laid in duct / cable tray / drawn through pipes etc including provision of lugs, glands, nuts, bolts & washers etc for connecting in LT panel/ motor terminal plate and testing on completion all as specified and directed. |
| 15 | Material and labour for M.S. Black Pipe plain end as per IS:3589 GR.330, nominal bore 200 mm dia, pipe thickness 5 mm with all necessary fittings such as flanges, bends, tees, reducers, elbows, dummy plates etc including cutting, welding and joining etc as per site requirement and applying two coats of synthetic enamel paint of approved colour over a coat of red oxide primer complete all as specified and directed. |
| 16 | Material and labour for M.S. Black Pipe plain end as per IS:1239 (Part-I), nominal bore 150mm dia, \"B\" class Medium Grade pipe with all necessary fittings such as flanges, bends, tees, reducers, elbows, dummy plates etc including cutting, welding and joining etc as per site requirement and applying two coats of synthetic enamel paint of approved colour over a coat of red oxide primer complete all as specified and directed. |
| 17 | Material and labour for M.S. Black Pipe plain end as per IS:1239 (Part-I), nominal bore 100mm dia, \"B\" class Medium Grade pipe with all necessary fittings such as flanges, bends, tees, reducers, elbows, dummy plates etc including cutting, welding and joining etc as per site requirement and applying two coats of synthetic enamel paint of approved colour over a coat of red oxide primer complete all as specified and directed. |
| 18 | Material and labour for M.S. Black Pipe plain end as per IS:1239 (Part-I), nominal bore 80 mm dia, \"B\" class Medium Grade pipe with all necessary fittings such as flanges, bends, tees, reducers, elbows, dummy plates etc including cutting, welding and joining etc as per site requirement and applying two coats of synthetic enamel paint of approved colour over a coat of red oxide primer complete all as specified and directed. |
| 19 | Supply and fix Vertical installation, Ball type Foot Valve of size 200 mm nominal bore, with flanged end, CI body and cover, Synthetic Nitrile Rubber Coated Ball, Leaded Tin Bronze Seat, CI Strainer, Carbon Steel fasteners, enamel/epoxy painted complete all as specified and directed by Engineer-in-Charge. |
| 20 | Supply and fix Vertical installation, Ball type Foot Valve of size 100 mm nominal bore, with flanged end, CI body and cover, Synthetic Nitrile Rubber Coated Ball, Leaded Tin Bronze Seat, CI Strainer, Carbon Steel fasteners, enamel/epoxy painted complete all as specified and directed by Engineer-in-Charge. |
| 21 | Supply and fix Cast Iron Y type strainer of size 200mm nominal bore, PN 16, Shell Test Pressure - 24 Kg/cm2g, S.S-304 Perforated Sheet Screen dia 3mm, Flanged Ends to BS 10 Table \"F\" including gasket, nuts, bolts, washers etc. complete all as specified and directed. |
| 22 | Supply and fix Cast Iron Y type strainer of size 100mm nominal bore, PN 16, Shell Test Pressure - 24 Kg/cm2g, S.S-304 Perforated Sheet Screen dia 3mm, Flanged Ends to BS 10 Table \"F\" including gasket, nuts, bolts, washers etc. complete all as specified and directed. |
| 23 | Supply and fix Horizontal installation, Ball type Non Return Valve (NRV) of size 150 mm nominal bore, PN 1.6 with both ends flanged, CI body and cover, Synthetic Nitrile Rubber Coated Ball, Leaded Tin Bronze Seat and Carbon Steel fasteners, enamel/epoxy painted complete all as specified and directed by Engineer-in-Charge. |
| 24 | Supply and fix Horizontal installation, Ball type Non Return Valve (NRV) of size 80 mm nominal bore, PN 1.6 with both ends flanged, CI body and cover, Synthetic Nitrile Rubber Coated Ball, Leaded Tin Bronze Seat and Carbon Steel fasteners, enamel/epoxy painted complete all as specified and directed by Engineer-in-Charge. |
| 25 | Supply and fix Cast Iron Rising Spindle Sluice Valve of size 150mm nominal bore, PN 1.6, as per IS : 14846 with flanged ends, hand wheel operated, stainless steel stem including necessary packing material, GI bolts, nuts and washers etc complete all as specified and directed by Engineer-in-Charge. |
| 26 | Supply and fix Cast Iron Rising Spindle Sluice Valve of size 80mm nominal bore, PN 1.6, as per IS : 14846 with flanged ends, hand wheel operated, stainless steel stem including necessary packing material, GI bolts, nuts and washers etc complete all as specified and directed by Engineer-in-Charge. |
| 27 | Material and labour for PCC 1:3:6 Type C1 using 20mm graded aggregate including necessary form work complete all as specified and directed by Engineer-in-Charge. |
| 28 | Material and labour for Reinforced cement concrete (nominal mix) 1:2:4, Type B1 (20mm graded aggregate) in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed. Note: Steel reinforcement shall be measured and paid separately. |
| 29 | Material and labour for Mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. |
| 30 | Material and labour for Mild steel TMT bars 6 mm to 8 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. |
| 31 | Material and labour for Rendering 10mm thick Cement Plaster in CM 1:4 on fair faces of brick work or concrete surfaces complete all as specified and directed by Engineer-in-Charge |
| 32 | Supply,lowering and installation in borewell, testing and commissioning of borewell submersible pump set suitable for delivering 300 LPM at 50 m total head, comprising multistage submersible pump with stainless steel construction, stainless steel shaft, dynamically balanced impellers, suitable thrust bearing arrangement, and water-lubricated motor, complete with compatible submersible electric motor of required rating, 3-phase, 415 V ±10%, 50 Hz, squirrel-cage induction type with Class ‘F’ insulation and IP68 protection, designed for continuous duty; includinglifting clamps, cable clamps, complete all as specified and as directed by Engineer-in-Charge. |
| 33 | Supply and connect 3 core flat PVC Insulated & PVC Sheathed Industrial copper conductor submersible cable of size 2.5 sqmm, 1100 volts grade confirming to IS:694 complete all as specified and directed by Engineer-in-Charge. |
| 34 | Flushing of the existing bore well, including mobilization of suitable flushing equipment (air compressor/water pump), removal of silt, sand, debris, and other obstructions from the bore, cleaning and development of the bore well to restore yield, continuous pumping/airlifting until clear water is obtained, disposal of extracted material, including suitable size of Cast Iron bore well cap along with fixing of MS clamp to the bore well casing, including cutting, alignment, tightening, sealing to make it secure and tamper-proof, protection against entry of debris and contaminants, and completion of the work in all respects as per standard practice and to the satisfaction of the Engineer-in-Charge. |
| 35 | Supply, lowering in borewell, connecting and testing of HDPE pipe, PE 100 grade, SDR series, PN 10 (SDR 13.6) of size 75mm complete all as specified and directed by Engineer-in-Charge. |
| 36 | Material & Labour for earthing complete with galvanized iron earth plate electrode 600 mm x 600 mm x 6 mm thick buried directly in ground (earth pit not less than 2.25 meters deep below ground level) with top edge of the plate not less than 1.5 meters below normal ground level connecting to 32 x 6 mm GI strip as earthing lead by means of bolts, nuts, check nuts and washers of galvanized iron or steel and earth wire protected by 50mm dia GI pipe medium grade and connected to Motor / panel board / earthing test point all as shown in electrical plate No. 3 of SSR Part-I(2009) and testing on completion complete all as specified and directed. Note :- The unit rate quoted shall also include for excavation, earth work in any type of soil, plain cement concrete 1:3:6 mix, Type C1 pit, 40mm thick RCC 1:2:4 mix type B1 cover reinforced with 8mm dia TMT bras @ 150mm C/C both ways, GI funnel with watering pipe, wire mesh, protection pipe, earth strip up to 7.50m long complete in addition to item No. 1(a) to (e) of preamble (Notes) under sub heading earthing, specified in SSR Part II. |
| 37 | Supply and fixing in replacement of Vertical Air Vessel made of MS material having 406 mm outer dia, 6mm thick and 1600mm height with dished ends and floor mounted legs completely welded duly painted with PO red including branch connections for fixing in pressure switch and connecting in pressure line suitable for fixing in automatic fire fighting pump control system complete all as specified and directed by Engineer-in-Charge. |
| 38 | Supply and fixing in replacement of pressure switch in IP55 enclosure CE marked suitable to use in auto fire pump control system, permissible operating pressure 18 bar, pressure setting range 4-12 bar and differential 0.5-1.6 bar, pressure connection G 1/4A, with silver contact material, rubber cable gland for cable entrycomplete all as specified and directed by Engineer-in-Charge. |
| 39 | Supply and connecting PVC insulated and PVC Round Sheathed, Multicore Annealed Bare Copper Conductor (flexible) industrial cable of size 1.5 sqmm, 8 core for Voltage Grade 1100 Volt, Conforming to IS 694 : 2010 complete all as specified and directed by Engineer-in-Charge. |
| 40 | Supply and connecting PVC insulated and PVC Round Sheathed, Multicore Annealed Bare Copper Conductor (flexible) industrial cable of size 1.5 sqmm, 2 core for Voltage Grade 1100 Volt, Conforming to IS 694 : 2010 complete all as specified and directed by Engineer-in-Charge. |
| 41 | Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) of any description and in any position not otherwise specifically provided for complete all as specified and directed by Engineer-in-Charge. |
| 42 | Dismantling wrought iron or mild steel work of any description not otherwise provided, complete all as specified and directed by Engineer-in-Charge. |
| 43 | Removing demolished cement concrete exc. 250 m but n exc. 500 m and depositing, complete all as specified and directed by Engineer-in-Charge. |
| 44 | Dimantling of existing Fire Pump Set Diesel Engine Driven 120 HP complete with base frame, suction & delivery pipe lines, foot valve, strainer, sluice valve, NRV etc, fuel tank, fuel pipes etc and shifting and handing over the pump set to MES store yard, complete all as specified and directed by Engineer-in-Charge. |
| 45 | Dimantling of existing Fire Pump Set Electric Motor Driven 120 HP complete with base frame, suction & delivery pipe lines, foot valve, strainer, sluice valve, NRV etc, and shifting and handing over the pump set to MES store yard, complete all as specified and directed by Engineer-in-Charge. |
| 46 | Dimantling of existing Electric Driven Jockey Pump Set 20 HP complete with base frame, suction & delivery pipe lines, foot valve, strainer, sluice valve, NRV etc, and shifting and handing over the pump set to MES store yard, complete all as specified and directed by Engineer-in-Charge. |
| 47 | Dimantling of existing Electric Driven Fresh Water Pump Set 75 HP complete with base frame, suction & delivery pipe lines, foot valve, strainer, sluice valve, NRV etc, and shifting and handing over the pump set to MES store yard, complete all as specified and directed by Engineer-in-Charge. |
| 48 | Taking out submersible pump set from the borewell along with column pipe, cable and starter panel etc complete and shifting and handing over the pump set to MES store yard, complete all as specified and directed by Engineer-in-Charge. |
| 49 | Note for item No. 41.00 to 45.00 : The Quoted rate shall deemed to include the cost of suitable lifting crane and vehicle for transportation of pump set from SVN colony pump house to MES store yard at 104 area. |
| 50 | SCHEDULE OF CREDITNote :- Amount of Rs. 72,275.00 indicated in Tender Documents as Schedule of Credit shall be deducted from the total quoted amount of BOQ. |
