|
| 1 | Excavation in Trenches/foundation for septic tanks, pipes, sewers, storm water drains, footings etc in all soils except soft and hard rock at all depths from average ground level including dewatering if necessary, dressing bottom to required level, profile/slope, clearing of all the areas involving excavation of all grass,rank vegetation, shrubs,bushes,cutting of treesupto 300mm grith measured at 1.0 mtr above ground leveldisposing the soil within a distance of 50m, complete as directed. |
| 2 | Filling available excavated earthin trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, levelling, lead up to 50 m. |
| 3 | Lead charges, including loading, unloading, stacking, the disposable Earth, rock, concrete, brick etc. by Mechanical transport for lead up to 1 KM. Note: Measurement of lead charges will be based on truck measurements with deduction of voids @20% and 50% for soils and rocks or debris respectively. |
| 4 | a) For soil |
| 5 | b) For debris |
| 6 | CEMENT CONCRETE of following mix using Pazzolona Portland Cement conforming to IS 1489 (M/s. ACC, Ultra Tech, Raasi, Birla, Coramandal, M/s. Andhra Cement Ltd., KCP), crushed sand and graded stone aggregates of 20 mm maximum size at and at all depths below plinth level including consolidation, finishing, curing, etc., complete but excluding formwork as per specifications |
| 7 | 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) |
| 8 | 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) |
| 9 | Reinforced cement concrete of M-30 grade (Minimum Cementations Content not less than 350 Kg/Cum) by insitu mixing using Weigh Batcher or RMC of Ultra Tech, Birla, Ready Mix up to specified level using Portland slag cement/Portland composite cement conforming to IS code (M/s. ACC, Ultra Tech, Raasi, Birla, Coromandal, Andhra Cements Ltd., KCP make) with crushed sand and graded stone aggregates of 20mm maximum size including mixing superplasticizer (M/s. Fosroc, Demach,Huntsman, Pedilite, Sunanda Chemicals, Agro Chemicals, MBT) in proportion as per manufacturer’s specifications,pumping/ lifting concrete to the required height, consolidation, finishing, curing, etc., complete as per specifications but excluding form work, centering and shuttering and steel reinforcement at all depths below and above floor level. |
| 10 | Providing centering and shuttering using steel shuttering plates vertical, horizontal, sloping including erecting, fixing, striking, removing and clearing for all cement concrete works as shown in drawings or as required including all chamfers, splays, keys, wedges, props, nails, bracings, brackets and applying one coat of shuttering oil on all shuttering surfaces in contact with concrete etc., as per Standard Practice complete as directed. in foundation plinth column flooring,machine foundation,piller,post,struts,sofits of beam,beam haunching,lintel,cantilever,girder, walls partition wall, sofits of cantilever suspended floors,landings, balconies,chajjas etc. |
| 11 | Supplying, fabricating and fixing in position reinforcement of HYSD bars/TMT bars 500D conforming to IS 1786 from approved source of make M/s Vizag steel/ SAIL/Jindal or any approved equivalent for reinforced cement concrete items at and at all depths and heights below and above existing floor level including transporting steel to site, removing of scales, straightening, cutting, bending, fixing and tying in position with two strands of 18 guage soft drawn annealed MS binding wire, providing cement mortar 1:1 cover blocks, etc. complete as specified and directed. |
| 12 | Providing and laying autoclaved aerated cement blocks masonry with 150/230/300 mm thick or other required size AAC blocks of makeM/s NCL, Aerocon, Greenstone in super structure below and above plinth level up to floor V level with approved block laying polymer modified adhesive mortar or in cement mortar 1:4 (1 cement : 4 coarse sand), complete as directed. |
| 13 | Brick work as per IS 2212 using fly ashbricks conforming to IS 12894 of Class Designation 7.5 and aboveas specified at all height anddepths with cement mortar 1:6{1 cement(M/s. ACC, Ultra Tech, Raasi, Birla, Coromandal, M/s. Andhra Cement Ltd., KCP): 6 crushed Sand} including raking out joints and simultaneously pointingthe joints with the same mortar, curing, scaffolding etc., complete as specified and directed. |
| 14 | HALF BRICK masonry as per IS 2212 using fly ash bricks conforming to IS 12894 of class designation 7.5 or aboveas specified in partitions walls in cement mortar 1:4 (1 cement: 4 crushed sand), including scaffolding, raking out joints, curing etc. complete and with Reinforced Cement Concrete (RCC) M15 (1:2:4) stiffeners of depth 75mmat every 900 mm height including form work, curing etc., complete as specified and directed, but excluding reinforcement. Note: Reinforcement will be measured and paid for separately under relevant item of schedule.-above plinth level up to 5th floor |
| 15 | Cement plastering 15 mm thick for internal walls in cement morar 1:4 {1 cement(M/s. ACC, Ultra Tech, Raasi, Birla, Coromandal, M/s. Andhra Cement Ltd., KCP): 4 River Sand} fininshed smooth at all height above plinth level over brick walls or concrete surface including making necessary grooves in between junctions or brick masonary and RCC and also other places wherever required over brick walls or concrete surface preparation of surface, steel/tubular scaffolding curing etc., complete as specified and directed. |
| 16 | Cement plastering 18mm thick in Two (2) coats over exterior masonry and concrete surfaces at and at all heights/depths above/below plinth levelwith base coat in Cement Mortar 1:5{1 cement(M/s. ACC, Ultra Tech, Raasi, Birla, Coromandal, M/s. Andhra Cement Ltd., KCP): 5 River Sand} 6mm thick and finishing coat in Cement Mortar1:3{1 cement(M/s. ACC, Ultra Tech, Raasi, Birla, Coromandal, M/s. Andhra Cement Ltd., KCP): 3 River Sand}6mm thick final rendering including addition of approved integrated waterproofing compound @ 2% by weight of cementor as per manufacturer’s Specifications for the base coatof make M/s. Fosroc/Demech/ Huntsman/ Pidilite/ SIKA Qualcrete / MBT/Sunanda Chemicals, making necessary grooves, bands, drip moulds, etc., as required, double steel/tubular scaffolding wherever necessary,curing, etc., complete as specified and directed. |
| 17 | Making good the damaged portion of walls with cement mortar mix (1 cement: 4 coarse sand) of thickness 12mm to 20mm at all height above plinth level over brick walls or concrete surface to restore the level of surface after removal of wall tiles/replacement of pipeline hacking over surfaces wherever required, scaffolding curing etc., complete as specified and directed. |
| 18 | Applying 2 (Two) coats of ready made putty of average thickness 1 mm ofBirla wall care/J.K. Wall putty over plastered wall surfaceincluding cleaning the surface with steel scrapper, wire brush, sand paper etc., filling increvices, holes, cracks with approved filler etc., finishing the surface neat and smooth without any undulations as specified and directed at all height including required scaffolding. |
| 19 | Painting with 3 coats of Acrylic emulsion paint (including primer) of interior grade oftractor emulsion ofAsian make or equivalent quality of /Berger/Nerolac makes of first quality and required shade over walls, ceilings etc., including scaffolding,preparing the surface smooth by sand papering, including necessary repairs to scratches, filling in crevices, holes and cracks etc., with approved filler etc., complete all as specified and directed. |
| 20 | Painting with 3 coats ( including a coat of cement primer of approved make) of antifungal Acrylic emulsion paint having 100% acrylic with silicon additives of Asian paints (Ultima) or equivalent quality paint from /Berger/Nerolac makes of first quality and required shade over walls, ceilings etc., including scaffolding, preparing the surface smooth by scrapping, sand papering,necessary repairs to scratches, filling in crevices, holes and cracks etc., with approved filler etc., complete all as specified and directed. |
| 21 | Painting with synthetic enamel paint in 3 ( three ) coats including a coat of appropriate primerof Asian/Berger/Nerolac make of 1st quality with required shade on walls, concrete surfaces,wooden/steel doors, windows, ventilators, composite units, louvers, rolling shutters, hand rail and balustrades, plastered surfaces etc., including scaffolding, preparing the existing surface smooth by sand papering, preparing the surface, brushing with wire brushes, scraping with steel scrapper etc., filling in crevices and cracks etc. with approved filler etc., complete as specified and directed. |
| 22 | Removing old paint by using scrubbing machine,preparing the surface smooth including necessary repairs to scratches etc. complete. |
| 23 | Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as specified and directed |
| 24 | Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge. |
| 25 | Dismantling very carefully the existing Brick masonry in cement motor with plastering on both sides including wall tiles, old pipelines if any very carefully at depths/heights above/below plinth level by suitable methods including erection of suitable scaffolding, stacing of useful materials and disposing the unserviceable debris within the lead of 50m, etc., complete as specified and directed. |
| 26 | Dismantling existing wooden / M.S/PVC (or other material) doors, windows, ventilations etc., including shutters, frames, holdfasts etc very carefully without damaging the frame and shutter etc., disposing the unserviceable materials within a lead of 100m completed as directed by Engineer-in-Charge. |
| 27 | Dismantling the existing mosaic tiles /glazed tiles ceramic tiles shahabad stone etc., in flooring / dado including dismantling, bedding mortar and disposing the debris within 50 m lead as directed by Engineer-in-Charge. |
| 28 | Dismantling old plaster, raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead |
| 29 | Dismantling of IWC/EWC and S or P trap at site including removal of cistern if required complete with disposal of dismantled material i/c malba all complete as per the direction of Engineer in Charge |
| 30 | Dismantling of C.I or asbestos rain water/soil pipe/Waste pipe/Vent pipe of following size with fittings and clamps including stacking servicable material within 50m lead. Complete as directed by EIC |
| 31 | 75 to 80mm dia |
| 32 | 100mm dia |
| 33 | 150mm dia |
| 34 | Transportation of dismantled doors/windows, broken tiles, bathrrom fittings/fixture and other debris by engaging tractor trolley including cost of fuel, wages of driver and required manpower for loading, transporting up to a lead of 1.0 KM, unloading and stacking the cut trees and branches in the placed shown by Engineer-in-Charge complete as directed.Measurement of lead charges will be based on truck measurements with deduction of voids @20% and 50% for soils and rocks or debris respectively. |
| 35 | Providing, laying, jointing, fixing, testing and painting as per color code of NFC/ZC heavy quality (Class ‘C’) M. S. GALVANISED PIPES as per IS:1239 (TATA/Jindal or equivalent make) including heavy quality HB fittings like elbows, collars, tees, unions, couplings, reducers, enlargers, bends and all other fittings required for the completion except screwed flanges confirming to IS:1239 and also as per the code of practice of water supply in buildings IS:2065 including removing of exisitng G.I. pipes and fixtures if any, laying under the floors, making holes/chasing in walls, roof slabs and making good the same to the original condition including cost of all jointing material like hemp yarn, white or red lead/Teflon tape, clamps, wooden gutties, screws, cement and painting with two coats ofanticorrosive bitumastic paint for embedded portion and two coats of synthetic enamel paint over a coat of zinc chromate/red oxide primer etc., complete including pressure testing the pipes with clean water as per specifications and connecting to existing supply lines or fittings and fixtures as the case may be. |
| 36 | 15 mm n. b. |
| 37 | 20 mm n. b. |
| 38 | 25 mm n. b. |
| 39 | 32 mm n. b. |
| 40 | 40 mm n. b. |
| 41 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes (SDR-11) conforming to IS 15778 of Ashirvad/Supreme or approved make, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe on exposed/recessed/underground surfaces to correct line, level, plumb using clamps as directed. This includes removing of existing pipes and fixtures if required, jointing of pipes & fittings with one step CPVC solvent cement, teflon tape,cost of cutting chases wherever required and making good the same with cement concrete/mortar, cutting or making hole or chases inRCC or brick work structure such as wall, column, beam, slab, chajja, dado etc. for passing the pipe line and reinstating all the damage to its original conditionincluding testing of joints at cerain locations complete as specified and directed |
| 42 | 15 mm dia-concealed including cutting chases and making good the walls etc |
| 43 | 20mm dia-concealed including cutting chases and making good the walls etc |
| 44 | 25mm dia-concealed including cutting chases and making good the walls etc |
| 45 | 32mm dia-concealed including cutting chases and making good the walls etc |
| 46 | 15mm dia-on exposed surface |
| 47 | 20mm dia-on exposed surface |
| 48 | 25mm dia-on exposed surface |
| 49 | 40mm dia-on exposed surface |
| 50 | 50mm dia-on exposed surface |
| 51 | Providing and fixing in position gun metal gate valves of following sizes of approved make confirming to IS778, including jointing material etc, as specified and directed. |
| 52 | 20 mm diameter |
| 53 | 25 mm diameter |
| 54 | 40 mm diameter |
| 55 | 50 mm diameter |
| 56 | Supplying and fixing following size uPVC UV-Stabilised soil / waste quality pipes and fittings ( SWR ) for soil, waste, vent, antisyphonege, HVAC waste pipe and rain water pipe lines consisting following items of work:- i) Providing and fixing uPVC UV-Stabilised Soil / waste pipe as per IS:13592 and IS:14735 Grade-B laid in floor & on Exposed faces of wall of Supreme make ii) Fixing the pipeline vertically by Metal clamps with rubber seal of approved makeiii) Providing and fixing uPVC cowl at the top of soil, waste water, rain water & vent pipe line. iv) Laying the pipe below floor / ground to proper slope and gradient for making connections of soil / waste water pipe line with inspection chamber or Manhole, including the cost of cement mortar, cement concrete, water proofing compound etc.v)Jointing the pipe with Solvent Cement & Rubber ring gasket with making holes in walls / floor grooving and redoing the same and brick support etc. Giving water-tightness test for the pipes laid as per codal provisions. Providing Ring Joint pipes at verticals and solvent cement jointed pipes at consealed locations. vi) Necessary cutting to the required length including short pieces, fittings with & without door, assorted fittings such as plugs, tees, couplers, reducers, cross tees, reducing tees, elbows, bends, cleaning pipe, single & double Y, vent cowl, gaskets, offsets, grattings, Tank / WC connectors etc. |
| 57 | 75 mm diameter |
| 58 | 110 mm diameter |
| 59 | Providing uPVC Floor Trap / Nahani Trap of following size conforming to IS 14735 with CP jalli on top, fixing the trap in position and connecting with waste water pipe by cement solvent / as per manufacturer\"s recommandation, embedding the trap in cement concrete 1:2:4 to correct level and gradient,closing the side inlets with plugs if required etc. all complete as specified and as directed |
| 60 | Nahani Trap of110 X 75mm size of Ashirvad (70001249)/Supreme make |
| 61 | Multifloor trap of 110 x 75 x 50 mm size of Ashirvad (70001252)/Supreme make |
| 62 | Providing and fixing of best quality PVC P trap for urinals of size 110mm X 110mm of Ashirvad (70002811)/Supreme make or approved equivalent with CP grating on top includingnecessary 1:2:4 cement concrete for embedding the trap connecting the trap to waste pipe, etc, complete as specified and directed. |
| 63 | Providing and fixing in position UPVC bottle Gully Trap of Supreme (Product code NUPHGT110G)/Ashirvad make of size 200mmX160mm including embedding the trap in 1:2:4 cement concrete, construction of brick masonry chamber in 230 mm thick brick masonry in cement mortar 1:4 over cement concrete bed of 1:3:6 of 100 mm thick, embedding the trap, plastering with cement mortar 1:4, 12 mm thick on inside & outside and all exposed surfaces, finished with a floating coat of neat cement, providing and fixing heavy duty C. I. frame and cover of size 300mmX300mm, 40mm thick cement concrete 1:2:4 bed over brickwork, painting the grating frame and cover with 2 coats of approved anticorrosive bitumastic paint, necessary connection with existing line etc., complete as directed |
| 64 | Providing & laying UPVC under ground drainage pipes & Fittings of Sudhakar/Nandi/Godavari makefor storm water drains& sewerage pipes of following size conforming to IS:15328 to proper level & grade, jointing including prviding coupler with cement solvent / welded joints / as per manufacturer\"s requirement, including encasing the pipe alround using cement concrete 1:3:6 complete to an offeset of D/2 where D= dia of pipe all as per specifictions, drawing and as directed by the E.I.C. item includes Providing and fixing UPVC fittings such as Bendes, Tees & Y, Reducers, Blanking Plugs, Couplers, Adaptors etc |
| 65 | 110 mm DN (SN 8kN/m²-SDR34) |
| 66 | 160 mm DN (SN 8kN/m²-SDR34) |
| 67 | Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement and making necessary channels for the drain etc. complete : For pipes 100 to 250 mm diameter |
| 68 | Constructing soak pit 1.20x1.20x1.20 m filled with brickbats including upvc drain pipe 110/160 mm diameter and 1.20 m long complete as per standard design. |
| 69 | Providing and fixing EUROPEAN WATER CLOSET of size close to the dimensions 350mmX480mmX395mm of Jaquar (CNS-WHT-551PSPP/551SSPP)/Parryware make/Hindware or approved equivalent , in white glazed vitreous, with integral \"P\" or \"S\" trap, Solid plastic heavy quality seat with lid of approved make and Colour with C.P.brass hinges,conforming to IS: 2548 (Part I & II), including cutting and making good floor, wall wherever required, as specified and directed |
| 70 | Providing and fixing coupled EUROPEAN WATER CLOSET of Parryware make/Hindware(Cat no. 92077) or approved equivalent , in white glazed vitreous, with integral \"P\" or \"S\" trap, Solid plastic heavy quality seat with lid of approved make and Colour with C.P.brass hinges, conforming to IS: 2548 (Part I & II), including cutting and making goodfloor, wall wherever required. |
| 71 | Providing and fixing approved ORRISA PATTERN W.C. of soze close to 580mm X 440mm of Parryware /Hindware(Cat no. 20042) or approved equivalent in white glazed vitreous chinaware, size 530 mm x 410 mm with \"P\" or \"S\" trap, conforming to IS: 2556. |
| 72 | Providing and fixing single flush PVC low level flushing cistern of 10 litres capacity conforming to IS: 7231 (Cico/Jaquar/Hindware(Cat no. C-1010)/Parryware make) with all internal PVC fittings mounted on a pair of brackets of heavy quality with 32 mm n. b. PVC flush pipe with bend of required length with all tools, synthetic adhesive, gasket etc. removingthe existing cistern if required, complete including connection to W. C. |
| 73 | Providing and fixing heavy quality solid plastic seat with lid for European Type water closet of parryware make /Hindware/Jaquar or approved equivalent. |
| 74 | Providing and fixingin toilets Health faucet of Parryware Make /Hindware/Jaquar (ALD-CHR-573) or equivelent with 1.2 meter long flexible tube or as per manufacturer\"s specifications inChrome finish and wall hook etc. complete as directed.. |
| 75 | Providing and fixing 40 mm n. b.C. P. brass single flush valve along with wall flange/plate of make Jaquar/Parryware/hindware or equivalent and other required accessories/fittings , including making recess in wall, flush pipe and connecting the valve with concealed water supply pipe. |
| 76 | Providing and fixing 15 mm n. b. heavy quality PVC connctor pipesuitable for hot and cold water for Cisterns, Wash basins, gyesers, urinals of suitable length with CP brass unions endsof ZOLOTO/PARRYWARE/HINDWARE/JAQUAR make. |
| 77 | Providing and fixing URINAL of size close to 385 mm x 325 mm x 635 mm of M/s.Jaquar(URS-WHT-13253N)/Parryware /Hindware make screwed to wall/dado with full threaded C.P. brass waste coupling to urinal, spreader, drain pipe etc. removing the existing urinal if required, complete as specified. |
| 78 | Providing and fixing in position of best quality rectangular shaped urinal PARTITION with frosted glass (8mm thick) of size 450mmX900MM of Jaquar (JSE-CHR-810US450X)/Hindware/Paryware make or approved equivalent, inclusing removing of existing partition if required as directed by Engineer-in-charge. |
| 79 | Providing and fixing best quality white vitreous china LABORATORY WASH BASIN of size 600 mm x 450 mm x 200 mm of Hindware/Parryware or equivalent make conforming to IS: 2556 Part IV supported on suitable wall brackets of heavy quality. |
| 80 | Providing and fixing best quality WASH BASIN of size 630mm X 450 mm including half pedestal, comprising best Indian make (Hindware (Cat no 10001)/Parryware/Jaquer wash basinwhite glazed, vitreous chinaware conforming to IS: 2556 Part IV supported on suitable wall brackets of heavy quality and of size mentioned above, including CP brass waste coupling,removing of existing wash basin if required as directed by Engineer-in-charge. |
| 81 | Providing and fixing best quality vitreous chinaware under the counter WASH BASIN of size close to 605mm x 430 mm x 200mm , of make Jaquar(CNS-WHT-705)/Hindware/Parrywareconforming to IS: 2556 Part IV including CP brass waste coupling, necessary supports, removal of wxisting wash basin if required, complete as specified and directed. |
| 82 | Providing and fixing CP Brass 32mm size heavy quality Bottle Trap of approved quality & make Jaquar (ALD-CHR-769L)/Parryware/ Hindware or approved equivalent, inludingextension pipe if required, removal of existing bottle trap if required, as per the direction of Engineer-in-charge. |
| 83 | Providing and fixing heavy quality half threaded/full threaded C. P. brass waste coupling of size 32mm of make JaquarParryware/Hindware or approved make. |
| 84 | Providing and fixing 32mm/40mm dia flexible P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. |
| 85 | Providing and fixing heavy quality 15mm C. P. brass wall mounted BIB TAPS of Hindware (Cat no. F730041)/Jaquar/Parryware/Jaquar make or equivalent with wall flange confirming to IS:8931. |
| 86 | Providing and fixing heavy quality 15 mm C. P. brass Long body BIB TAPS of Hindware(F730011CP)/Jaquar/Parryware/Jaguar make or equivalent with wall flange and confirming to IS:8931. |
| 87 | Providing and fixing heavy quality 15 mm C. P. brass Pillar cock of Jaquar/Parryware /Hindware make (F730002CP) or equivalent confirming to IS:8931. |
| 88 | Providing and fixing heavy quality 15 mm C. P. brass E Sensor Tap of Parryware/Hindware/Jaquar make (Cat no. F240003CP) or equivalent. |
| 89 | Providing and fixing heavy quality 15 mm C. P. brass 2 way bib cock of Parryware /Hindware/Jaquar make (F330004CP) or equivalent with wall flange and confirming to IS:8931. |
| 90 | Providing and fixing 15 mm n. b. heavy quality C. P. brass angle valve confirming to IS 8931 of make Parryware Code /hindware (F730039CP)/Jaquar or equivalent. |
| 91 | Providing and fixing 15 mm n. b. heavy quality C. P. brass Push Type urinal angle valve confirming to IS 8931 of make Jaquar/Parryware/hindware or equivalent. |
| 92 | Providing and fixing heavy quality 15 mm C. P. brass Concealed stop cock of Jaquar/Parryware /Hindware (Cat no F730013CP) make or equivalent with wall flange and confirming to IS:8931. |
| 93 | Providing and fixing heavy quality 15 mm C. P. brass Non Telephonic wall mixer of Jaquar/Parryware /Hindware(F730016CP) wall flange and confirming to IS:8931. |
| 94 | Providing and fixing heavy quality 15 mm C. P. brass 3 in 1 wall mixer of Parryware/Hindware(F730020CP) wall flange and confirming to IS:8931. |
| 95 | Providing and fixing heavy quality 15 mm C. P. brass Deck Mounted Sink Cock of Parryware/Hindware make (F730034CP) or equivalent confirming to IS:8931. |
| 96 | Providing and fixing decorative round shaped C. P. brass SHOWER ROSE if dia 200mm without arm of make Jaquar/Parryware/ Hindware(F160125) or approved equivalent |
| 97 | Providing and fixing decorative round shaped C. P. brass long shower arm of 450mm length of make Jaquar/Parryware/ Hindware or approved equivalent |
| 98 | Providing and fixing C. P. brass TOWEL RAIL of approved design and make of 600mm length, fixed to wall with C. P. brass screws, screwed on to rawl plugs etc., complete of Parrywaremake/Hindware/Jaquar or equivalent. |
| 99 | Providing and fixing CP brass soap dish of make Parryware Code /hindware/Jaquar or equivalent. |
| 100 | Providing and fixing 150X150 mm recessed type CP brass Toilet Paper Roll Holder with cover of Parryware make/Hindware/Jaquar or equivalent as specified and directed |
| 101 | Providing and fixing C. P. brass Twin Robe Hook, fixed to wall with C. P. brass screws, screwed on to rawl plugs etc., complete of Parry- ware/Hindware/Jaquar or equivalent. |
| 102 | Providing and fixing SS 304 Cloth Hanger with four hooks, fixed to wall or doors with C. P. brass screws, screwed on to rawl plugs etc., complete as directed by Emgineer-in-charge. |
| 103 | Providing and fixing beveled edge mirror of required sizesuperior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete |
| 104 | Providing and fixing movable grab bar for differently abled of Dolphy make (DHGB0002) or approved equivalent of size 600mm consisting of stainless steel tube with nylon grip, complete as directed by Engineer-in-charge. |
| 105 | Providing and fixing fixed grab bar for differently abled of Dolphy make (DHGB0014) or approved equivalent of size 600mm consisting of stainless steel tube with nylon grip, complete as directed by Engineer-in-charge. |
| 106 | Providing & fixing following vitrified tiles for flooring, skirting, staircase etc. using10 mm thick tiles (or thickness as specified by manufacturer) of make Johnson, Somani, Kazaria or any other approved equivalent of required shade, design, colour and pattern laidusing high polymer modified quick-set tile adhesives (Water based) separately for wall and floors conforming to IS: 15477 of Roff/MYK or approved equivalent make, to receive the floor tiles including cleaning, close jointed and pointed with matching epoxy grout of required colour, metallic/non-metallic Edge Tile Trim/Tile beading to be provided at junctions of two surfaces for smooth edges, finished to levels,slope or plumb as required including cutting of tiles, hacking of floor, removing and reinstating the loose and cracked surfaces/damaged plastering with suitable repairs etc., complete as specified and directed |
| 107 | fully polished fully glazed digital printed vitrified tiles of size 600mm X 600mm for dado |
| 108 | Matt/rustic/antiskid vitrfied tiles of size 600mmX600mm for floor |
| 109 | Providing and fixing 16mm to 18mm thick gang saw cut, mirror polished/honed finish, machine cutgranitefor floors, Kitchen platform, Vanity Counter, window sills, facias, staircase and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 ( 1 cement : 4 Coarse sand), jointed treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, moulding, polishing, forming single/double nosing at edges, making of 3 no of grooves for staircase threads wherever required. complete as specified and directed |
| 110 | Constructing wash basin platform of approximate width 600mm and maximum length upto 3 meters using two machine polished granite slabs (each 16mm to 18mm thick) fixed back to back with aralditeincluding making openings in granite for under the counter wash basins, holes for pillar taps, moulding, rubbing and polishing of cut edges, making recess in the wall, inserting the platform in the wall till 40mm, grouting with cementious grout of Fosroc (Conbexrtra) or approved make, forming nosing at the edges of the counter, etc, complete as specified and directed. |
| 111 | Fixing of available ceramic wall tiles / floor tiles in toilets by providing 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete (Supply of tiles only in the scope of department. Lead will be seperately for shifting of tiles from store) |
| 112 | Providing and fixing factory made single extruded WPC (wood polymer composite) solid door/window frames/chowkhat of following sizes comprising of virgin PVC polymer ofK value 57-60, calcium carbonate and natural fibers (wood powder/rice husk/wheat husk) and non-toxic additives fabricated with mitered joints after applying PVC solvent Cement & screwed with full body threaded star headed SS screws having minimum frame density of 750 Kg/cum and manufactured by RAJSHRI or equivalent, screw withdrawl strength of 990N, minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of class A category with propoerty of being termite/borer proof, water/moisture proof and fire retardent and fixed in position with SS dash fastners/Hold fast of required dia and length, painting with required color, complete as directed |
| 113 | WPC door frame (85x45) |
| 114 | WPC door frame (100X65) |
| 115 | Providing and fixing factory made Decorative (laminated)/Plain single extruded WPC (wood polymer composite) solid plain flush door shutter pf follwoing size comprising of virgin PVC polymer ofK value 57-60, calcium carbonate and natural fibers (wood powder/rice husk/wheat husk) and non-toxic additives having minimum density of 650 kg/cum manufactured by RAJSHRI or equivalent, screw withdrawl strength of 1800N(Face) & 900N(Edge), minimum compressive strength of 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of class A category with propoerty of being termite/borer proof, water/moisture proof and fire retardent and fixing with Stainless steel butt hinges of required size with fully body threaded star headed counter sunk SS scews, including supplying and fixing of necessary fixtures such as aluminum tower bolts, round aluminum handles (both sides), aldrops (both sides),painting the door with required color, complete as directed. |
| 116 | 30mm solid WPC flush door shutter-plain |
| 117 | 35mm solid WPC flush door shutter-decorative (laminated on both sides). |
| 118 | Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSMand 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. 4mm thick Acrylic should be provided in the louvers. The ventilator should be fixed to the wall with 100% packing with SS screws and silicon packing all round the frames & screws, complete and as directed by Engineerin-charge. |
| 119 | Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Windows of casement (open)/Sliding (Two track/Three track with musquito mesh) from the profile the mini. size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with multi point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or tinted glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with SS screws and silicon packing all round the frames & screws, complete and as directed by Engineerin-charge. |
| 120 | Providing and mixing integral crystalline admixture of M/s Pidilite/Fosroc/Cika/BASF make for water proofing tretament to RCC structures at the time of transporting of concrete into the drum of RMC truck, as per manufacturer\"s specifications. The material shall meet the requirement as specified in ACI-212-3R-2010 i.e. by reducing the permeability of concrete by more than 90%, compared with control concrete as per DIN 1048. The crystalline admixture shall be capable of self-healing of cracks upto a width of 0.5mm. The work shall be carried out all complete as per specifications and the direction of Engineer-in-charge. |
| 121 | Supply, fabrication and erection of structural steel work usingstandard steel rolled sections/standard plain plates/chequered plates coforming to IS 2062, of M/s tata,vizag steel, Jindal or SAIL or any other make using ingots of above firms at and at all depths and heights below and above plinth level for providing supports to platforms in bathrooms/Kitchen or other steel work including trasporting, cutting, welding/bolting using necessary bolts/anchor fastners for columns, foundation bolts,including painting with one coat of approvedzinc chromate/red oxide primer and two coats of Synthetic Enamel paint (Asian paint, Berger, Johnson and Nickelson, Pedilitie, Nerolac) of approved shade for all exposed surfaces,complete as specified and directed. |
| 122 | Supplying and filling in spetic tanks., with approvedcoarse sand /aggregate of size 6mm to 20mm complete as directed. |
| 123 | Providing and fixing of 560mm diaHeavy duty C.I.cover with frame of double seal pattern of required size and shape conforming to IS 1726, painting with two coats of bitumastic paint, placing over the RCC slab etc. complete as directed by Engineer-in-charge |
| 124 | Providing and fixing SS railing made out of commercial chromium steel tubes SS 304, of various diameters, of approved make, 2 mm wall thickness, pattern as shown in drawing/as directed including supplying or fabricating, fittings like SS bends, tees, etc., welding the pipes using TIG welding or any other approved method, grinding/buffing the welded joints smooth, erecting the railing in position in line, level and plumb, fixing tailing in position by grouting/or any approved system, cleaning, polishing the joints if required, scaffolding etc., complete all as specified and directed. |
