|
| 1 | Excavating trenches by mechinical / manual means of required width forpipes, cables, etc including excavation for sockets, and dressing of sides,ramming of bottoms, for all depth, including getting out the excavatedsoil, and then returning the soil as required, in layers not exceeding 20cm in depth, including consolidating each deposited layer by ramming,watering, etc. and disposing of surplus excavated soil as directed, withina lead of 50 m :All kinds of soil Pipes, cables etc. exceeding 80 mm dia. butnot exceeding 300 mm dia |
| 2 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level1:2:4 (1 cement: 2 coarse sand (zone-lll) derived from natural sources: 4 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 3 | Centering and shuttering including strutting, propping etc. and removal of form work for:Foundations, footings, bases for columns |
| 4 | Brick work with common burnt clay F.P.S. (non-modular) bricks of classdesignation 7.5 in foundation and plinth in: Cement mortar 1:4 (1 cement: 4 coarse sand) |
| 5 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 6 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works |
| 7 | Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). |
| 8 | Chequered terrazzo tiles 22 mm thick with graded marble chips of size upto 6 mm in floors, jointed with neat cement slurry mixed with pigment tomatch the shade of the tiles, including rubbing and polishing complete, on20 mm thick bed of cement mortar 1:4 (1 cement :4 coarse sand) : Ordinary cement without any pigment |
| 9 | Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand). Medium shade pigment using 50% white cement 50% Grey cement |
| 10 | Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1: 4 (1 cement: 4 coarse sand): (a)25 mm thick |
| 11 | Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge :(a)Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent |
| 12 | Providing and fixing PVC rain water pipe : Single socketed pipes 200 mm dia. |
| 13 | Providing & fixing UV stabilized fiberglass reinforced plastic sheet roofing up to any pitch, including fixing with polymer coated ‘J’ or ‘L’ hooks, bolts & of nuts 8 mm dia. G.I plain/bitumen washers complete but excluding the cost of purlins, rafters, trusses etc. The sheets shall be manufactured out 2400 TEX panel roving’s incorporating minimum 0.3% ultra-violet stabilizer in resin system under approximately 2400 psi and hot cured. They shall be of uniform pigmentation and thickness without air pockets and shall conform to IS 10192 and IS 12866.The sheets shall be opaque or translucent, clear or pigmented, textured or smooth as specified. 2 mm thick flat |
| 14 | 12 mm cement plaster:1:6 (1 cement: 6 coarse sand) |
| 15 | 15 mm cement plaster on rough side of single or half brick wall of mix: 1:6 (1 cement: 6 coarse sand) |
| 16 | Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete |
| 17 | Finishing walls with water proofing cement paint of required shade:New work (Two or more coats applied @ 3.84 kg/10 sqm) |
| 18 | Providing and applying white cement-based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 19 | Distempering with 1st quality acrylic distemper (Ready mix) having VOC content less than 50 grams/ litre of approved brand and manufacture to give an even shade:Old work (one or more coats) |
| 20 | Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour.Two coats |
| 21 | Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete |
| 22 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :One or more coats on old work |
| 23 | Finishing walls with water proofing cement paint of required shade :Old work (one or more coats @ 2.20 kg/10 sqm) complete. |
| 24 | Finishing walls with Acrylic Smooth exterior paint of required shade : Old work (One or more coat applied @ 0.90 ltr/10 sqm) |
| 25 | Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete,including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-Charge.With cement mortar 1:4 (1cement: 4 coarse sand) |
| 26 | Providing & fixing White vitreous china water closet squatting pan (Indian type) along with “S” or “P” trap including dismantling of old WC seat and “S” or “P” trap at site complete with all operations including all necessary materials, labour and disposal of dismantled material including malba, all complete as per the direction of Engineer-in charge.Orissa pattern W.C Pan of size 580x440 mm |
| 27 | Providing and laying APP (Atactic Polypropylene Polymer) modified prefabricated five layer, 3 mm thick water proofing membrane, black finished reinforced with glass fibre matt consisting of a coat of bitumenprimer for bitumen membrane @ 0.40 litre/sqm by the same membrane manufactured of density at 25°C, 0.87 - 0.89 kg/litre and viscosity 70 – 160 cps. Over the primer coat the layer of membrane shall be laid using butane torch and sealing all joints etc., and preparing the surface complete. The vital physical and chemical parameters of the membrane shall be as under: Joint strength in longitudinal and transverse direction at 23°C as 350/300 N/5 cm. Tear strength in longitudinal and transverse direction as 60/80N. Softening point of membrane not less than 150°C. Cold flexibility shall be upto -2°C when tested in accordance with ASTM, D - 5147. The laying of membrane shall be got done through the authorized applicator of the manufacturer of membrane :3 mm thick |
| 28 | Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. Nominal concrete 1:4:8 or leaner mix (i/c equivalent design mix) |
| 29 | Dismantling tile work in floors and roofs laid in cement mortar includingstacking material within 50 metres leadFor thickness of tiles 10 mm to 25 mm |
| 30 | Dismantling stone slab flooring laid in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 metres lead |
| 31 | Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. |
| 32 | Dismantling aluminium/ Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable material and stacking of serviceable material with in 50 meters lead as directed by Engineerin-charge. |
| 33 | Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved. |
| 34 | Taking out existing CC interlocking paver blocks from footpath/ central verge, including removal of rubbish etc., disposal of unserviceable material to the dumping ground, for which payment shall be made separately and stacking of serviceable material within 50 metre lead as per direction of Engineer-in-Charge. |
| 35 | Laying old cement cocrete interlocking paver blocks of any design/ shape laid in required line, level, curvature, colour and pattern over and including 50 mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineerin-charge. (Old CC paver blocks shall be supplied by the department free of cost). |
| 36 | Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge. |
| 37 | Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete.10 litre capacity - White |
| 38 | Providing and fixing solid plastic seat with lid for pedestal type W.C. pan complete:White solid plastic seat with lid |
| 39 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.(a) flexible pipe 32 mm dia |
| 40 | Providing and fixing PTMT 15 mm Urinal spreader size 95x69x100 mm with 1/2” BSP thread and shapes, weighing not less than 60 gms. |
| 41 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVCplain & brass threaded fittings and fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the sameincluding testing of joints complete as per direction of Engineer in Charge.Concealed work, including cutting chases and making good the walls etc.20 mm nominal dia Pipes |
| 42 | Providing and fixing uplasticised PVC connection pipe with brass unions :45 cm length (a)15 mm nominal bore |
| 43 | Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet :100 mm diameter |
| 44 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :(a) 15 mm nominal bore |
| 45 | Providing and fixing C.P. brass pillar taps of approved quality conforming to IS:8931 : 15 mm |
| 46 | Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms.(a)15 mm nominal bore |
| 47 | Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. (a)15 mm nominal bore |
| 48 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931. (a)15 mm nominal bore |
| 49 | Providing and fixing PTMT Ball cock of approved quality, colour and make complete with Epoxy coated aluminium rod with L.P./ H.P.H.D. plastic ball.15 mm nominal bore, 105 mm long, weighing not less than 138 gms |
| 50 | Supplying and fixing C.I. cover 300x300 mm without frame for gully trap(standard pattern) the weight of cover to be not less than 4.5 kg |
| 51 | Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round pipes including bed concrete as per standard design :200 mm diameter pipe |
| 52 | Providing and fixing in position pre-cast R.C.C. manhole cover and frameof required shape and approved quality Rectangular shape 600x450 mm internal dimensions |
| 53 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :For fixed portion(a) Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 54 | For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) (a)Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 55 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): (a) With float glass panes of 8 mm thickness (weight not less than 20 kg/sqm) |
| 56 | Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge.(a)With stainless steel cover plate minimum 1.25 mm thickness |
| 57 | Providing and fixing false ceiling at all heights with integral densified calcium silicate reinforced with fibre and natural filler false ceiling tiles of Size 595x595 mm of approved texture, design andpatterns as per CPWD Specification 2019, to be laid in true horizontal level suspended on inter locking metal T-Grid of hot dipped galvanised iron section of 0.33 mm thick (galvanized @ 120gramspersqmincludingbothsides) comprising ofmain-Trunners of size 24x38 mm of length 3000 mm, cross - T of size 24x32 mm of length 1200 mm and secondary intermediate cross-T of size 24x32 mm of length 600 mm to form grid module of size 600 x 600 mm, suspended from ceiling using galvanised mild steel items (galvanizing @ 80 grams per sqm) i.e. 12x50 mm long dash fasteners, 6 mm dia fullythreaded hanger rod upto 1000 mm length and L-shape level adjuster of size 76x25x25x1.6 mm fixed with grid and Z cleat of size 25x37x25x1.6 mm thick with precut hole on both 25 mm flange to pierce into 12x50 mm or even bigger size dash fastener if require, fixed with Glavanised iron perimeter wall angle or size 24x24x0.40 mm of length 3000 mm to be fixed on periphey wall / partition with the help of plastic raw plugs at 450 mm center to center and 40 mm long dry wall S.S screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in-Charge.With 15 mm thick Tegular edged light weight calcium silicate false ceiling tiles |
| 58 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :a)Two or more coats on new work. |
| 59 | Providing & Fixing ofWelded steel wire fabric of required width having rectangular mesh painted with two or more coats of enamel paint of approved shade over a coat of primer (Supplying of welded steel wire fabricandPriming & Painting to be paid for separately) a) Made of G.I. wire of dia 4 mm |
| 60 | Supply and installation, testing of Swimming pool FLOOR INLET as per sample approved by Engineer in charge of External thread of 2\", internal plain 50mm for a suitable flow as desired flow as desired By Engineer in charge |
| 61 | Providing and fixing Locker system -3 tier locker made of heat, bacteria, water, chemical, scratch and impact resistant 03 mm and 09 mm thick solid compact laminate pannel i/c doors self side pane, top and bottom panels finished with approved texture ,shade as per the detail drawing and and as per the IS 2046 (Indian standard ) . the compact item should have Green guard certificate . It should be Anti bacteria(Shree Ram House). This also include providing and fixing in position necessary hardware made ofallumonium(Grade -6063-T6) & Stainlesssteel(Grade 304) (1) Cam (2) hinges (3) Front section (4) Back section (50 Infill section (6) Rubber linning (7) screw and bolt. Lockers shall be constructed with 4 aluminium interlocking supporting frame work making it strong nd rigid . Standard dimensions of lockers unit shall be width 300 mm x depth 450 mm x height 1800 mm. (a) Locker system -3 tier of make Greenlam Sturdo. Marino or equivalent. |
| 62 | Providing and fixing polypropylene against UV rays, white or any required coloured, rectangular shape and required width & depth grating for swimming pool including providing and fixing of PVC angle of required size on both sides of drain, as per specification and direction of engineer in charge |
| 63 | Providing and fixing 1st quality pool tiles conforming to IS:15622:2006 (Group Bib) of minimum 8 mm for various tiles of make like HR Johnson or equivalent or better make in all colours, shades design and prints as approved by Engineer in Charge to be fixed over 3 to 4 mm bad of polymer adhesive as per IS:15477 (Ardex, Endura ferrous crete by Manchanda Enterprises, Pidilite make or better or equivalent make) to correct line, level and plan with 2 mm joint between the tile (method in application will be guided by manufacturer specification) and grouted with readymade polymer grout (Bal Endura make or superior or equivalent complete as per directions of Engineer in Charge. (1) Floor and inner wall of main swimming pool with rectangular size tiles 247 x 122 or as approved by Engineer in Charge (a) with light or white shade. |
| 64 | Cleaning and re-grouting of pool tiles of approx. size 247mm x 122mm. The work includes: Raking out of complete damaged grout in the joints of swimming pool tiles and Re-grouting the said joints with readymade polymer grout (Bal Endura make or equivalent. The agency shall completely clean the surface of all pool tiles and ensure that no epoxy marks are left due to the re-grouting work. Also, all previously existing hard water / grout stains shall have to be removed by using softening compound and rubbing with sponge / cloth. (no harsh acids shall be used). The persistent stains / marks shall have to be removed by dry rubbing with hand held rubbing machine fixed with non woven U5 type 100mm dia scrubbing pads. The job shall include removing all loose / deleterious material upto 50 meter lead / out of the swimming pool and washing of pool with soap & water after completion of work. Arrangement for washing i.e. water supply and for removal of wash water by running pump, shall be provided by dept. Complete job as per the directions of engineer in charge. |
| 65 | Supplying and fixing in position SFRC precast V railing /fence of overall dimension 1000 mm (length) 1035 mm (Height) 50 mm (thickness) manufacture with M-30 grade of concrete using vibro compaction process using jointless FRP moulds so as to achieve shuttering finish of approved quality and make \"KK\" or equivalent and as per the direction of Engineer in charge. i/c transportation, loading, unloading as per the design drawing approved by Engineer in Charge. |
| 66 | Less for GST Correction Factor @ 0.027 on DSR items 1 to 58 |
