|
| 1 | Earth work in surface excavationnot exceeding 30 cm in depthbut exceeding 1.5 m in width as well as 10 sqm on plan including getting out and disposal of excavated earth upto 50 m and lif upto 1.5 m, as directed by Engineer-in- Charge: |
| 2 | All kinds of soil |
| 3 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. |
| 4 | All kinds of soil. |
| 5 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 and for all lif. |
| 6 | Providingandlayinginpositioncementconcreteof specified grade excluding the cost of centering and shuttering - All work up to plinth level : |
| 7 | 1:2:4 (1cement : 2 coarse sand (zone-Ill) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 8 | 1:4:8 (1Cement : 4 coarse sand (zone-Ill) derived from natural sources: 8 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 9 | Centering and shuttering including strutting, propping etc. and removal of form work for: |
| 10 | Foundations, footings, bases for columns |
| 11 | Providing andlaying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement: 2 coarse sand (zone-Ill) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources). |
| 12 | Providing and laying in position specified grade of reinforced cement concrete,excludingthecostofcentering,shuttering,finishingand reinforcement - All work up to plinth level : |
| 13 | 1:1.5:3(1 cement: 1.5 coarse sand (zone-Ill) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 14 | Reinforced cement concrete work in walls (any thickness),including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor fivelevel,excludingcost of centering,shuttering, finishingand reinforcement: |
| 15 | 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 16 | Steelreinforcement forR.C.C.workincludingstraightening,cutting, bending, placing in position and binding all complete upto plinth level. |
| 17 | Thermo-Mechanically Treatedbars of gradeFe-500D or more. |
| 18 | Steelreinforcement forR.C.C.workincludingstraightening,cutting, bending, placing in position and binding all complete above plinth level. |
| 19 | Thermo-Mechanically Treatedbars of gradeFe-500D or more. |
| 20 | Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3(1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 21 | Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS: 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : |
| 22 | 300x16 mm |
| 23 | Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : |
| 24 | 100x10 mm |
| 25 | Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : |
| 26 | 125 mm |
| 27 | Providing and fixing factory made uPVC door frame made of uPVC extrudedsectionshavinganoveralldimensionasbelow(tolerance ±1mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame to be Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19 mm and 1 mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturer\"s specification and direction of Engineer- in-charge |
| 28 | Extruded section profile size 48x40 mm |
| 29 | Providing and fixing to existing door frames. |
| 30 | 24 mm thick factory made PVC door shutters made of styles cleats. The shutter frame filled and rails of a uPVC hollow section of size 59x24 mm and wall thickness 2 mm (± 0.2 mm) with inbuilt edging on both sides. The styles and rails mitred and joint at the corners by means of M.S. galvanised/ plastic brackets of size 75x220 mmhavingwallthickness1.0mmandstainlesssteel screws. The styles of the shutter reinforcedby inserting galvanised M.S. tube of size 20x20 mm and 1mm (± 0.1 mm) wall thickness. The lock rail made up of \"H\" section, a uPVC hollow section of size 100x24 mm and 2 mm (± 0.2 mm) wall thickness, fixed to the shutter styles by means of plastic/galvanised M.S. with a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer\"s specification and direction of Engineer- in-charge. (For W.C. and bathroom door shutter). |
| 31 | Providing and fixing factory made uPVC glazed/wire mesh windows/ doors comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanizedmild steel section madeof requiredshape & size asper CPWDSpecification,uPVC extrudedglazingbeads,interlocksandlnlinesashadaptor(where ever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum8mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-Charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-Charge. Wire mesh / Glazing of plain/ toughened/ laminated/ double glass unit with / without high performance coatings as per design requirements and conforming to IS: 3548 & IS: 16231 shall be paid separately.Note:-StructuraldesignproofcheckedfromaGovernment Engineering Institute,tobeprovidedbythemanufacturerfor (i) Sites with basic wind speed > 45 m/sec as per IS 875 — Part 3 (ii) Sites with structure height more than 20m for all wind speeds |
| 32 | Fixed window/ ventilator without mullion /transom. Using R1 series with frame (33 mm & above) x (35 mm & above). (Height upto 0.90 metre) |
| 33 | Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. |
| 34 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. |
| 35 | Electric resistance or induction butt welded tubes |
| 36 | Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, bufing, polishing andmakingcurvature(wherever required)andfittingthesame with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). |
| 37 | Cement concrete flooring 1:2:4 (1cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. |
| 38 | 40 mm thick with 20 mm nominal size stone aggregate |
| 39 | Providing andlayingCeramic glazed floor tiles of size 300x300mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement :4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete. |
| 40 | Providing and laying vitrified floor tiles in diferent sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. |
| 41 | Size of Tile 600x600 mm |
| 42 | Providing ridges or hips of width 60 cm overall width plain G.S. sheet fixed with polymer coated J or L hooks, bolts and nuts 8 mm dia G.I. limpet and bitumen washers complete. |
| 43 | 0.80 mm thick with zinc coating not less than 275 gm/m2 |
| 44 | Providing valleys of 90 cm wide overall in plain G.S. sheet fixed with polymer coated J or L hooks, bolts and nuts 8 mm dia G.I. limpet and bitumen washers complete : |
| 45 | 1.60 mm thick with zinc coating not less than 350 gm/m2 |
| 46 | Providing and fixing of 40 cm overall width plain G.S. sheet fixed with polymer coated J or L hooks, bolts and nuts, G.I. limpet and bitumen washer complete, bent to shape and fixed in wall with cement mortar 1:3 (1 cement: 3 coarse sand). |
| 47 | 1.00 mm thick with zinc coating not less than 275 gm/m2 |
| 48 | Providing and fixingPre-Printed galvanune (PPG:) steel profile sheets AZ-150 of brand Tata Bluescope steel, Everest Industries Ltd., JSW Steel Ltd., Jindal Indai Ltd. or equivalent (size, shape andpitch of corrugation as approved by Engineer-in-Charge) 0.50 mm ( + 0.05%) total coated thickness with zinc coating 150 grams per sqm as per IS:277, in 240 mps steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single lenght upto 12 metre or as desired by Engineer-in-Charge. The sheet shall be fixed using self drilling/self tapping screws (Xylan) of size (5.5 x 55 mm ) woith EPDM seal, complete upto any pitch in horozontal/ vertical or currved surfaces, excluding teh cost of purlins, rafters and trusses and including cutting to size and shape wherever required.. |
| 49 | 12 mm cement plaster of mix: |
| 50 | 1:4(1 cement: 4 fine sand) |
| 51 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade: |
| 52 | Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture |
| 53 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 54 | Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture,including applying additional coats wherever required, to achieve even shade and colour. |
| 55 | Two coats |
| 56 | Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content. |
| 57 | With ready mixed pink or grey primer on wood work (hard and soft wood) having VOC content less than 50 grams/ litre |
| 58 | Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. |
| 59 | Nominal concrete 1:3:6 or richer mix (including equivalent design mix) |
| 60 | Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 metres lead : |
| 61 | Of area 3 sq. metres and below |
| 62 | Dismantling steel work in built up sections in angles, tees, flats and channels including all gusset plates, bolts, nuts, cutting rivets, welding etc. including dismembering and stacking within 50 metres lead. |
| 63 | Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. |
| 64 | For thickness of tiles 10 mm to 25 mm |
| 65 | Dismantling of flushing cistern of all types (C.I./PVC/Vitrious China) including stacking of useful materials near the site and disposal of unserviceable materials within 50 metres lead. |
| 66 | Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: |
| 67 | White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests |
| 68 | Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : |
| 69 | W.C. pan with ISI marked white solid plastic seat and lid |
| 70 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: |
| 71 | White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap |
| 72 | White Vitreous China Angle back wash basin size 400 x 400 mm with single 15 mm C.P. brass pillar tap |
| 73 | Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge. |
| 74 | Providing and fixing G.I. inlet connection for flush pipe connecting with W.C. pan. |
| 75 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. |
| 76 | Flexible pipe 40 mm dia |
| 77 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 78 | Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. |
| 79 | 450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms |
| 80 | Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge. |
| 81 | ProvidingandfixingChlorinatedPolyvinylChloride(CPVC)pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings and fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. |
| 82 | 15 mm nominal dia Pipes |
| 83 | 20 mm nominal dia Pipes |
| 84 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work |
| 85 | 25 mm nominal dia Pipes |
| 86 | Providing and placing on terrace (at all floor levels) polyethylene water storagetank,IS : 12701marked,withcoverandsuitablelocking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 87 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : |
| 88 | 15 mm nominal bore |
| 89 | Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. |
| 90 | 15 mm nominal bore |
| 91 | Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x 300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: |
| 92 | 100x100 mm size P type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 93 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fastenersto be paid for separately) : |
| 94 | For fixed portion Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) |
| 95 | Forshuttersofdoors,windows&ventilatorsincluding providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) |
| 96 | Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) |
| 97 | Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge. |
| 98 | Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side |
| 99 | Providing and fixing powder coated aluminium work (minimum thickness of powder coating 50 micron) consisting of tee/ angle sections, of approved make conforming to IS : 733 in frames of false ceiling including aluminium angle cleats with necessary C.P. brass/ stainless steel sunk screws, aluminium perimeter angles fixed to wall with stainless steel rawl plugs @ 450 mm centre to centre and fixing the frame work to G.I. level adjusting hangers 6 mm dia. with necessary cadmium plated machine screws all complete as per approved architectural drawings and direction of the Engineer-in-charge (level adjusting hangers, ceiling cleats and expansion hold fasteners to be paid for separately). |
| 100 | Providing and laying Polyethylene septic tank for 30-35 flushing made of polyethylene a single moulding with 3 chambers and 2 manholes, the high wall/thickness of septic tank should with standard load and pressure of the earth to a greate extent, fulfilling the technical specification of Type-III United Polyethylene spetic tank or equivalent capacity of flusing per day should be 30-35, diameter of tank 1000mm, lenght 2800mm, minimum thickness 10mm number if chamber 2 2 number of manhole 1 No. if size 500mm (Dia) and Air vent pipe of 50mm dia etc. all complete laid as per the direction of Engineer-in-Charge (Note EArth work in Ecavation, Cement Concrete bed & vent pipe shall be paid seperately). |
| 101 | Providing and fixing tactile (warning) tiles of size 300 × 300 × 9.8 mm, conforming to IS 15622 and IS 13801:1993 (Reaffirmed 2018), of approved make, colour and shade, on floor and wall surfaces, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointed with grey cement slurry @ 3.3 kg/sqm and grouted with white cement mixed with matching pigment, complete as directed by the Engineer-in-Charge |
| 102 | Providing and fixing stainless steel cloth hook (Grade 304) wall-mounted type with 2 prongs, fixed with rawl plugs and stainless-steel screws, including drilling, alignment and finishing complete |
| 103 | Providing and fixing alarm pull cord system suitable for Divyang (persons with disabilities), consisting of nylon cord with wall-mounted holder, alarm switch with indicator and buzzer, connected to power supply for emergency use in accessible toilets, including testing and commissioning all complete as per the direction of E-In-C. |
| 104 | Providing and fixing automatic electric hand dryer suitable for wall mounting, made of high-impact ABS or stainless-steel body, having automatic infrared sensor operation, rated for 230 V AC, with air speed > 90 m/s and power consumption up to 2 kW, includingtesting and commissioning complete. |
| 105 | Providing and fixing uPVC moulded fittings/accessories conforming to IS 14735, including jointing with solvent cement, complete as directed. |
| 106 | Plain bend (Single Socket), required degree 75mm dia |
| 107 | Plain bend (Single Socket), required degree 110mm dia |
| 108 | Door bend (Single Socket), required degree: 75mm dia |
| 109 | Door bend (Single Socket), required degree: 110mm dia |
| 110 | Providing and fixing soil, waste & vent uPVC SWR Pipe Type-B conforming to IS 13592 (latest), jointing with PVC solvent cement (conforming to relevant standard), including cutting, chamfering, jointing, testing, and making good the wall/floor/ground, complete as directed: |
| 111 | 75mm dia |
| 112 | 110mm dia |
| 113 | Providing and fixing self-adhesive reflective vinyl stickers with bilingual lettering (English & Hindi) and international accessibility symbols for Divyang (Persons with Disabilities), on smooth surfaces such as glass, wall or metal, including design, printing, cutting, surface cleaning and pasting complete as per direction of Engineer-in-Charge. |
| 114 | Providing and laying hollow ceent concrete block walling upto floor five level using achine-ade hollow concrete blocks of ix 1:3:6 (1 ceent : 3 coarse sand :6 graded stone aggregate of 12nominal size) having a minimum compressive strenght of 3.5N/mm2 at 28 days, conforming to IS 2185 (Part-I) -1979, laid in cement mortar 1:6 ( 1 ceent : 6 coarse sand), including all scaffolding,curing,raking of oints and finishing of oints flish, etc., coplette as per direction of Engineer-in-Charge. |
| 115 | 200thick hollow block masonary using blocks of size 400 m x 200 m x 200 m. |
| 116 | Providing and laying hollow ceent concrete block walling upto floor five level using achine-ade hollow concrete blocks of ix 1:3:6 (1 ceent : 3 coarse sand :6 graded stone aggregate of 12nominal size) having a minimum compressive strenght of 3.5N/mm2 at 28 days, conforming to IS 2185 (Part-I) -1979, laid in cement mortar 1:6 ( 1 ceent : 6 coarse sand), including all scaffolding,curing,raking of oints and finishing of oints flish, etc., coplette as per direction of Engineer-in-Charge. |
| 117 | 150thick hollow block masonary using blocks of size 400 m x 150 m x 200 m. |
| 118 | Providing and laying hollow ceent concrete block walling upto floor five level using achine-ade hollow concrete blocks of ix 1:3:6 (1 ceent : 3 coarse sand :6 graded stone aggregate of 12nominal size) having a minimum compressive strenght of 3.5N/mm2 at 28 days, conforming to IS 2185 (Part-I) -1979, laid in cement mortar 1:6 ( 1 ceent : 6 coarse sand), including all scaffolding,curing,raking of oints and finishing of oints flish, etc., coplette as per direction of Engineer-in-Charge. |
| 119 | 100thick hollow block masonary using blocks of size 400 m x 100 m x 200 m. |
| 120 | Providing and fixing in position facias or eaves of 30 c width, including fixing with nuts and bolts. |
| 121 | 18 m thick Wooden Plastic Composite (WPC) board. |
| 122 | Providing and fixing factory-made uPVC Top-Hung Sliding Door (Without botto rail) ade of multi-chambered, lead-free uPVC extruded profiles having wall thickness not less than 2.5 m, duly reinforced with glavanized ild-steel sections, mitred and fusion -welded at corners, fixed to wall with stainless-steel anchor fasteners (M8 x 75 ), crescent lock, stopper and bottom floor guilde for aligent, complete wih all fittings,accessories and fixtures, the shutter panels provided wih 12 m thick soild WPC (Wood Plastic Composite) board infill of approved quality and density not less han 700kg/m2, fixed in grooves of uPVC frame using EDP gasket and weather-proof silicone sealant, coplette in all respects as per manufacturer\"s specification and direction of Engineer-in-Charge. |
| 123 | Providing and fixing glazing in uPVC doors,windows,venilator shutters and partitions, including all necessary neading and snap fitings of EDPM rubber/neoprene /neoprene gasket etc complete, al as per architectural drawings and as directed by the ngineer-in-Charge. |
| 124 | With float glass panes of 4.0 m thick (weight not less than 10kg/sq). |
